arthur loibl gmbh used for sale

Frequency-controlled heating laboratory press with force measuring device -Pressure 20 KN / 2 tons -Pressing area 220 220 mm -Maximum pressing force at 220 220 mm: 41 N / cm² -Hot press with moveable lower pressing plate, electric drive with gear reduction, force measurement is carried out by means of strain gauge sensor -Heat output approx. 1 KW -Plate temperature 120 ° C -Dwell time / duration of laminating: 1-10 s -Pneumatic connection 6bar required -Power supply 400 V, 16 A -Sliding table with integrated positioning pins, lower pressing plate, pneumatic drive -Pressing panels with switchable integrated vacuum channel -Electrical control system integrated with PLC control display in the front panel of the machine -Side channel pump to generate the vacuum

Industrial freezer down to -40°C TTS 40-944U Fryka Refrigeration Freezer down to -40°C Tyxp TTS 40-944U Manufacturer Fryka Kältetechnik GmbH LED temperature display Electronic control ST100 (membrane keyboard) Alarm equipment Standby switch Current connection 400Volt, 16A Former original price 20.000.-EUR Quote from manufacturer description: "The housing is made entirely of stainless steel sheet. The insulated outer lid is lockable on the handle. In addition to the outer lid with double seal, the interior is closed with PE insertion lids. The lid is fixed to the base housing with folding hinges and is dampened by gas springs when opening and closing. This allows an opening angle of 90°. The insulation between the interior and the housing jacket is made of two-component insulating foam. The evaporator tubes of the chiller are wound around the interior. The inner she ...

NEW diesel engine Scania Dc13-72A incl. Starter to exchange give old Scania engine DC12 Power: 1500/1800 326/372 kW MIW GmbH Motoren-Instandsetzungs-Werk North-West-ring 8 D-27404 Zeven/Germany Tel:0049(0)4281 950583 Fax:0049(0)4281-950585

Unused gearboxes, angular gearboxes, partly without electric motors, partly with electric motors. Manufacturers e.g. PWH Plants + Systems GmbH These types and others pre-raetig: 1. PWH 90KW Type K2SZG250 n1=1500 rpm n2= 75 rpm i=20 P=90 KW Length over everything: 120cm Width over all approx. 55cm Height approx. 56cm Diameter of shaft rear (lies laengs) 45mm Transducer of the shaft front (lies transverse) outside 160mm Transducer of the shaft front (lies transversely) inside 140mm Weight-cooked 1,000kg 2. PWH 45KW Type KSZG200 n1=1470 rpm n2= 73.5 rpm i=20 P=45 KW All over: 94cm Pq7hwm Width over all approx. 45cm Height approx. 46cm Diameter of shaft rear (lies laengs) 50mm Transducer of the shaft front (lies transverse) outside 150mm Transducer of the shaft front (lies transverse) inside 120mm, passage 100mm Weight-cooked 600kg 3. PWH 37KW Type KSZG180 ...

Powder mixing plant Ytron Dr. Karg, built in 2012 and with Flow tank. Capacity up to 10 to/h The powder was treated via pipes into the flow vessel. The whey or milk powder mixture was via the plate heater and hot water Cycle in batch operation with the basic tanks set and then released for further processing. With frame and staircase a.) With a GEA plate heater for treatment the powder water solution. Hersteler FA. GEA TDS GmbH, Sarstedt Type: VT 20 CD-9-C-16 170/7412 No. 3600 4074, year of construction 2012 b.) With wall-mounted control cabinet system Siemens S 7 for process technology, CIP tank system and Control of cleaning paths c.) With 1 CIP system for the standing tank as a 1-tank cleaning system for the Batch operation and for the powder mixing plant Self. Content CIP tanks 15,000 l insulated, deformed inwards in the upper area with valve no ...

Gas-heated annealing and hardening furnace make SCHNEIDER GmbH Witten type 6 KMachine -No: 31 built in 2002Technical specifications:Chamber size W x D: 1200 x 900 mmin the rear part of the chamber step downwards: depth 500 x height 400 mmOpening W x H: 1200 x 470 mmmax.temperature: 1300 °Connected load: 300 kWHeating medium: natural gasExternal dimensions approx. W x D x H: 2200 x 2600 x 2650 mmWeight: 5850 kgWith- MEILI hand winch for opening the oven door- Attention without switch and control cabinet!usedPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Manufacturer: Expert Systemtechnik GmbH Make: cutEXPERT Type: Variojet year: 2009 Characteristics: Single table with dimensions:Laenge = 6500mm; Width = 3300mm; Height = 1850mmWeight: 1500kg Power consumption: 7.0 kW Cutting head count: 2 Manufacturer: AllfiType: V High Speed high pressure pump :Manufacturer: UhdeType: HP19/37-SYear of construction: 2009 Foerderpower 3.8l/min Design pressure: 4000bar Engine power: 37kW weight: 1450kg ready to use

properties: Used Schrenrollenbahn Condition: used Material: Steel (galvanized) Incl. SEW motors (9 drive units) Incl. 10 feet, height adjustable Speed adjustable Expertly dismantled and packaged specifications Scissor roller conveyor of the manufacturer Schmid Systemtechnik GmbH Year of construction: 2018 Conveying width: 600mm Material: Steel Total length extended: 9.000mm Total length retracted: 4.950mm Conveying width: 1.000mm Roll diameter: 50 mm Head: 820mm to 1040mm Number of rolls: 91 pieces Tailor-made solutions for your intralogistics We are your competent partner for roller conveyors, belt tracks, inclined conveyors or telescopes for loading and unloading your goods! We are happy to prepare your individual offer or advise you on the conception or assembly questions. Simply let us know your needs and local conditions. Take advantage ...

Heat pump or chiller, water-cooled, Type: OCEAN Tech OCT-H 150, M.T.A. S.p.A. OCEAN Tech OCT-H 150 are heat pumps (alternatively chiller) water / water for indoor installation without hydraulic circuit (pump, accumulator) incl. crankcase heating, phase monitoring. (The dry cooler, storage tank and pumps are not included in the offer). Heating capacity 50.2 Capacitor Hot water temp. Outlet / Entrance: 45 / 40°C Volume flow m³/h 6.33 Evaporator Medium: Hot water Cooling water temp. Outlet/ Entrance: 7 / 12°C Medium: Cold water Refrigerant R 410A (Cooling capacity 44.6 – optionally possible) Evaporator Cold water temp. Outlet/ Entrance: 7 / 12°C Volume flow m³/h 7.64 Medium: Cold water Capacitor Cooling water temp. Outlet / Entrance: 35 / 30°C Medium: Cooling water Refrigerant R 410A Electrical data: Voltage V 400, frequency Hz 50, phases Ph 3 pow ...

Praezision tube Residual bestaend from the production of gas pressure cylinders Stainless steel, probably V2A or V4A Laenge each 6m The following dimensions should be available, exact quantities on request or on order. 3x20 7x23 4x28 1x40 Sale against bid either as a total length or by length or by meter Special price

- with two driven hoed rolls different models: - Grain squeeze HQ1.5 (kW) - Grain squeeze HQ3 (kW) - Grain squeeze HQ4 (kW) - Grain squeeze HQ5.5 (kW) - Grain squeeze HQ7.5 (kW) New machine - best condition

1 pc. stainless steel tank with large inspection flap and 3 sampling points, staplerfaehig and stackable additional staplerfaehiger catcher in stainless steel (not pictured) Fasungsvermoegen 1,000 litres Operating pressure 0.1 bar For hazardous substances of class 3 6.1 b and Weight Tank 212 kg Collecting pan approx. 240kg Special price

Mobile press system with belt or packing press - can be varied by hourly performance More detailed information on request!; New machine - best condition

Rated power up to 300 kg/h engine power press 1.5 (2.0) Muehle 1.5 (2.0) kW (PS) Electrical connection 400V 50 Hz (3 phases) Electrical fuse 16 A Laenge 1200 mm width 1000 mm He 1880 mm Basket and juice tray in 1.4301 / AISI 304 press force 24.2 to Press pressure 380 bar Juice yield up to 65% Connection for juice drain 30mm High juice drain 525 mm Hoehe Marc ejection 585 mm Supplied 1 press bag 100l, 3 insert huellen 48cm, 3 Press inserts made of acacia wood 48cm ; New machine - best condition

Heat pump or chiller, water-cooled, Type: OCEAN Tech OCT-H 150, M.T.A. S.p.A. OCEAN Tech OCT-H 150 are heat pumps (alternatively chiller) water / water for indoor installation without hydraulic circuit (pump, accumulator) incl. crankcase heating, phase monitoring. (The dry cooler, storage tank and pumps are not included in the offer). Heating capacity 50.2 Capacitor Hot water temp. Outlet / Entrance: 45 / 40°C Volume flow m³/h 6.33 Evaporator Medium: Hot water Cooling water temp. Outlet/ Entrance: 7 / 12°C Medium: Cold water Refrigerant R 410A (Cooling capacity 44.6 – optionally possible) Evaporator Cold water temp. Outlet/ Entrance: 7 / 12°C Volume flow m³/h 7.64 Medium: Cold water Capacitor Cooling water temp. Outlet / Entrance: 35 / 30°C Medium: Cooling water Refrigerant R 410A Electrical data: Voltage V 400, frequency Hz 50, phases Ph 3 pow ...

Nominal Rating 1000 l/h; prepared - top condition

- for the production of mash - easy operation and easy cleaning nominal power up to 4200 kg/h engine power 5.5 (7.5) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical protection 16 A Laenge 7 30 mm width 690 mm Hoe 1410 mm Height assumption 1410 mm Weight 88 kg material 1.4301 / AISI 304 Hoehe mash release 470 mm Supplied New machine - best condition

Manufacturer: SHW Machine Tools Type: UF 21 Routes X,Y, Z: 1000, 600, 625mm Control: Heidenhain TNC 155 Table: Folding table 1000 x 630 mm Automatic swivel head Pinole 120mm Milling spindle holder SK 40 Speed 2500rpm Overhaul 2016 Partial overhaul 2022 About us: MBM Maschinenservice & Gebrauchtmaschinen GmbH, is a freelance specialist for SHW machine tools. Our main task is in the field of machine tool milling machines. Our services include spare parts deliveries, on-site customer service, machine overhauls and control modernizations. Performances: - Used machines - Spare parts - Customer service - Machine service - Machine overhauls - Control modernization

Rated power up to 150 kg/h engine power 1.1 (1.5) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 1100 mm Width 990 mm He 1430 mm Juice pan in 1.4301 / AISI 304 press force 14 to Press pressure 380 bar Juice yield up to 75% Connection for juice drain 30mm High juice drain 470 mm Supplied delivery 7 presses 70x70cm, 8 pressing inserts made of acacia wood 41x41cm ; New machine - best condition

Machine type TIG inverter welding system gas-cooled DC system Eurotronic brand Type Porty TIG 1601 DC (i)-2 Connection voltage 1 x 230 Volt Setting range 3 - 160 amps Duty cycle 60 % ED at 160 Ampere 100% ED at 100 amps Current adjustment infinitely variable weldable material thickness 4 mm Cooling inverter by built-in fan Cooling burner gas-cooled Version portable mounting system Fuse 16 amps Dimensions L x W x H 400 x 240 x 360 mm Weight 10 kg Age approx. 15 years Condition workshop tested, very good, incl. UVV test protocol Scope of delivery welding system with the following accessories: 1 piece TIG burner SR 17, 8 mtr. long 1 piece ground cable 1 piece pressure reducer with 2 pressure gauges 1 pair of TIG gloves 1 piece spare parts box kpl. Equipped Warranty 6 months from the date of delivery Listen-Werk-Price ex stoc ...

Machine type TIG inverter welding system gas-cooled DC system Make EP-Systems Type TopTIG 160 HF Connection voltage 1 x 230 Volt Setting range 5 – 160 amps Duty cycle 60 % ED at 160 Ampere 100% ED at 130 amps Current adjustment infinitely variable weldable material thickness 4 mm Cooling inverter by built-in fan Cooling burner gas-cooled Version portable mounting system Fuse 16 amps Dimensions L x W x H 410 x 240 x 320 mm Weight 10 kg Age 4 years Condition workshop tested very good incl. UVV test protocol Scope of delivery welding system with the following accessories: 1 piece TIG burner 4 mtr. long 1 piece ground cable 1 piece pressure reducer with 2 pressure gauges 1 pair of TIG gloves 1 piece spare parts box kpl. Equipped Warranty 6 months from the date of delivery Original price 1.550,00 € + VAT Price kpl. from ...

Rated power up to 300 kg/h engine power 1.5 (2.0) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 1250 mm width 1210 mm He 1510 mm Juice tray in 1.4301 / AISI 304 press force 24 to Press pressure 380 bar Juice yield up to 75% connection for juice drain 30mm High juice drain 420 mm Scope 9 pressing tins 80x80cm, 10 pressing inserts made of acacia wood 50x50cm ; New machine - best condition

Machine type TIG inverter welding system gas-cooled DC system Merkle brand Type LiteTIG 190 DC Connection voltage 1 x 230 Volt Setting range 5 – 190 amps Duty cycle 25 % ED at 190 Ampere 60% ED at 140 amps 100% ED at 115 amps Current adjustment infinitely variable weldable material thickness 5 mm Cooling inverter by built-in fan Cooling burner gas-cooled Version portable mounting system Fuse 16 amps Dimensions L x W x H 410 x 150 x 240 mm Weight 7.4 kg Age 6 months Condition workshop tested, as new, incl. UVV test protocol Scope of delivery welding system with the following accessories: 1 piece TIG burner 4 mtr. long 1 piece ground cable 1 piece pressure reducer with 2 pressure gauges 1 pair of TIG gloves 1 piece spare parts box kpl. Equipped 24 months warranty 1 piece instruction manual List factory price ex stock wit ...

Machine type TIG inverter welding system gas-cooled DC system Merkle brand Type LiteTIG 210 DC Connection voltage 1 x 230 Volt Setting range 5 – 210 amps Duty cycle 20 % ED at 210 Ampere 60% ED at 145 amps 100% ED at 135 amps Current adjustment infinitely variable weldable material thickness 6 mm Cooling inverter by built-in fan Cooling burner gas-cooled Version portable mounting system Fuse 16 amps Dimensions L x W x H 410 x 150 x 240 mm Weight 8 kg Age 6 months Condition workshop tested, as new, incl. UVV test protocol Scope of delivery welding system with the following accessories: 1 piece TIG burner 4 mtr. long 1 piece ground cable 1 piece pressure reducer with 2 pressure gauges 1 pair of TIG gloves 1 piece spare parts box kpl. Equipped 24 months warranty 1 piece instruction manual Listen-Werk-Price ex stock with 2 ...

- two rated power up to 600 kg/h engine power 1.5 (2.0) kW (PS) Electrical connection 400V 50 Hz (3 phases) Electrical fuse 16 A Laenge 1890 mm width 1210 mm He he 1510 mm Juice pan in 1.4301 / AISI 304 press force 24 to Press pressure 380 bar Juice yield up to 75% connection for juice drain 30mm High juice drain 420 mm Scope 18 pressing tuecher sier 80x80cm, 20 press inserts made of acacia wood 50x50cm ; New machine - best condition

Machine type TIG inverter welding system gas-cooled DC and AC system Merkle brand Type LiteTIG 210 AC/DC Connection voltage 1 x 230 Volt Setting range 5 – 210 amps Duty cycle 20 % ED at 210 Ampere 60% ED at 140 amps 100% ED at 130 amps Current adjustment infinitely variable weldable material thickness 6 mm Cooling inverter by built-in fan Cooling burner gas-cooled Version portable mounting system Fuse 16 amps Dimensions L x W x H 410 x 150 x 240 mm Weight 9 kg Age 6 months Condition workshop tested, as new, incl. UVV test protocol Scope of delivery welding system with the following accessories: 1 piece TIG burner 4 mtr. long 1 piece ground cable 1 piece pressure reducer with 2 pressure gauges 1 pair of TIG gloves 1 piece spare parts box kpl. Equipped 24 months warranty 1 piece instruction manual Listen-Werk-Price ex st ...

Machine type compressor Birkenstock brand Type K8 / 40 / 230 Connection voltage 1 x 230 Volt Version mobile version Fuse 16 amps Dimensions L x W x H 1,120 x 400 x 760 mm Weight 60 kg Age 6 months Condition very little used Boiler capacity 40 liters intake capacity 250 litres/min. delivery quantity 175 litres/min pressure 10 bar Cylinder 1 piece Original price incl. water separator 1.035,00 € + VAT Price incl. water separator from stock Munich 895,00 € + VAT Compressed air hose, incl. plug-in sleeve and quick coupling, 9 mm Ø 10 mtr. long, ready to connect 34,80 € + VAT Sach-Nr. S-50.98.10 Compressed air hose, incl. plug-in sleeve and quick coupling, 9 mm Ø 25 mtr. long, 9 mm Ø 61,10 € + VAT Sach-Nr. S-50.98.25 Compressed air hose, incl. plug-in sleeve and quick coupling, 9 mm Ø 50 mtr. long, 9 mm Ø 104 ...

- the classic must press in fruit processing nominal power up to 180 kg/h engine power 1.1 (1.5) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 1078 mm width 800 mm Hoehe 1700 mm Hoehe Acceptance 1 142 mm Basket in 1.4301 / AISI 304 press force 16.1 to Press pressure 320 bar Juice yield up to 65% Connection for juice flow High juice drain 480 mm Hoehe marc ejection 642 mm Scope of delivery 1 press bag 60l, 3 inserts of 38cm, 3 press inserts made of acacia wood ; New machine - best condition

Ground precision ball screw, D63mm, 1275mm, Steinmeyer, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, Type 1516.6/30.63.1010.1275 P3, Fa, Steinmeyer, Ball screw diameter 63 mm, Pitch 30 mm, Length of thread 1010 mm Length of ball screw nut 325 mm, Max. total stroke 685mm, Total length of the spindle 1275 mm Diameter for coupling with motor 42 mm Diameter bearing seat 50 mm Functional guarantee! We cannot provide a conventional guarantee and warranty for second-hand parts. However, we give you a functional guarantee. If the uni ...

Rated power up to 300 kg/h engine power 1.5 (2.0) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 1178 mm Width 800 mm Hoehe 1907 mm Juice pan in 1.4301 / AISI 304 Press force 24.2 to Press pressure 380 bar Juice yield up to 65% Connection for juice drain 30mm High juice drain 525 mm High marc ejection 640 mm Supplied 1 press bag 100l, 3 inserthuellen 48cm, 3 press inserts made of acacia wood 48cm ; New machine - best condition

Ground precision ball screw, D63mm, 1458mm, Steinmeyer, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, Type 1516.555/10.63.1215.1458 P3, D63mm, 1458mm, Fa. Steinmeyer, Ball screw diameter 63 mm, Pitch 10 mm, Length of thread 1215 mm Length of ball screw nut 192 mm, Max. total stroke 1023 mm, Total length of the spindle 1458 mm Diameter for coupling with motor 32 mm Diameter bearing seat A 40 mm Functional guarantee! We cannot provide a conventional guarantee and warranty for second-hand parts. However, we give you a functional ...

Ground precision ball screw, D40mm, 1479mm, Steinmeyer, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, Type 3526.7/25.40.852.1479E P3, D40 mm, 1479 mm, Fa. Steinmeyer, Ball screw diameter 40 mm, Pitch 25 mm, Length of thread 852 mm Length of ball screw nut 140 mm, Max. total stroke 712 mm, Total length of the spindle 1479 mm Diameter for coupling with motor 28 mm Diameter bearing seat A 32 mm, Diameter bearing seat B 20 mm Diameter 34 mm x 340 mm Functional guarantee! We cannot provide a conventional guarantee and warranty for  ...

Rated power up to 600 kg/h engine power 1.5 (2.0) kW (PS) Electrical connection 400V 50 Hz (three-phase) Electrical fuse 16 A Laenge 2080 mm width 1030 mm He 1450 mm Juice pan in 1.4301 / AISI 304 Pressing force 24 to Press pressure 380 bar Juice yield up to 75% connection for juice drain 30mm High juice drain 400 mm Supplied scope of delivery 80x80cm, 20 pressing inserts made of acacia wood 50x50xcm ; New machine - best condition

Ground precision ball screw, D63 mm, 962 mm, Steinmeyer, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, Type (123170) 409801/3-1, D63 mm, 962 mm, Fa. Steinmeyer Ball screw diameter 63 mm, Pitch 10 mm, Length of thread 745 mm Length of ball screw nut 152 mm, Max. total stroke 593 mm, Total length of the spindle 962 mm Diameter for coupling with motor 38 mm Diameter bearing seat A 50 mm Functional guarantee! We cannot provide a conventional guarantee and warranty for second-hand parts. However, we give you a functional guarantee. ...

Packing press 180P2 Inox with hydraulic lifting and vertical device Nominal power up to 1200 kg/h engine power 1.5 (2.0) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 2250 mm Width 840 mm He 1880 mm Maximum acceptance 1380 mm Weight 1020 kg Material 1.4301 / AISI 304 Press force 50 to Press pressure 270 - 320 bar Juice yield up to 75% Connection for juice drain 1 1/4 High juice drain 420 mm Scope 22 Pressing tummy 100x100cm + 24 press inserts Stainless steel 65x65cm ; New machine - best condition

Ground precision ball screw, D50 mm, 1143mm, Steinmeyer, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, incl. roller bearings on both sides. 3526.508/30.50.900.1143E P3 D50 mm, 1143 mm, Fa. Steinmeyer Ball screw diameter 50 mm, Pitch 30 mm, Length of thread 900 mm Length of ball screw nut 193 mm, Max. total stroke 707 mm, Total length of the spindle 1143 mm Diameter for coupling with motor 38 mm Diameter bearing seat A 40 mm, Bearing seat A 25mm Functional guarantee! We cannot provide a conventional guarantee and warranty for  ...

- replaceable stainless steel sifties for adjusting the grinding unit - food-grade - self-sufficient use or mounted directly on pre-basket presses nominal power up to 650 kg/h engine power 1.5 (2.0) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical protection 16 A La 496 mm width 434 mm He 885 mm He he with frame 1360 mm Hehe Assumption 1360 mm Weight 28 kg weight (without / with frame) 28 / 42 kg material 1.4301 / AISI 304 Hoehe mash release 690 mm Supplied cutter 8mm ; New machine - best condition

Ground precision ball screw, D50x10, 1741mm, Steinmeyer, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, Type 1516.364/10.50.1410.1741, Ball screw diameter 50 mm, Pitch 10 mm, Length of thread 1410 mm Length of ball screw nut 150 mm, Max. total stroke 1260 mm, Total length of the spindle 1741 mm Diameter for coupling with motor 35 mm Diameter bearing seat A 44 mm, Diameter bearing seat B 48 mm Functional guarantee! We cannot provide a conventional guarantee and warranty for second-hand parts. However, we give you a functional gu ...

- Adjustment of the grinding unit - for the crushing of various fruit varieties food-grade nominal power up to 1000 kg/h engine power 2.2 (3.0) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 532 mm width 519 mm 1151 mm Hehe with frame 1532 mm He he Assumption 1532 mm Weight 45 kg weight (without / with frame) 45 / 59 kg material 1.4301 / AISI 304 Hoehe mash release 666 mm Supplied New machine - best condition

Ground precision ball screw, D50x10, 1741mm, Steinmeyer, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, Type 1516.322/10.50.1410.1741 P3, MAG IAS X.0109.0329, Ball screw diameter 50 mm, Pitch 10 mm, Length of thread 1410 mm Length of ball screw nut 150 mm, Max. total stroke 1260 mm, Total length of the spindle 1741 mm Diameter for coupling with motor 35 mm Diameter bearing seat A 44 mm, Diameter bearing seat B 48 mm Functional guarantee! We cannot provide a conventional guarantee and warranty for second-hand parts. However, we  ...

- Cores are ejected separately from the mash nominal power up to 1000 kg/h engine power 5.5 (7.5) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 2 014 mm width 770 mm Hoehe 1 615 mm He He Assumption 1 615 mm Weight 220 kg Material 1.4301 / AISI 304 Connection for mash pump DN 65 AG Hoehe mash release 430 mm Hoehe stone ejection 490 mm ; New machine - best condition

Precision ball screw, D50 mm, 1253 mm Rexroth, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, Type model Star D50 mm, 1253 mm, Fa. Rexroth, Ball screw diameter 50 mm, Pitch 10 mm, Length of thread 1000 mm Length of ball screw nut 180 mm, Max. total stroke 820 mm, Total length of the spindle 1253 mm Diameter for coupling with motor 32 mm Diameter bearing seat A 35 mm Functional guarantee! We cannot provide a conventional guarantee and warranty for second-hand parts. However, we give you a functional guarantee. If the unit does n ...

Precision ball screw, D50mm, 1520mm, Rexroth, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, D50 mm, 1520 mm, Fa. Rexroth, Ball screw diameter 50 mm, Pitch 20 mm, Length of thread 1370 mm Length of ball screw nut 215 mm, Max. total stroke 1155 mm, Total length of the spindle 1520 mm Diameter for coupling with motor 24 mm Diameter bearing seat A 40 mm, Diameter bearing seat B 42 mm Functional guarantee! We cannot provide a conventional guarantee and warranty for second-hand parts. However, we give you a functional guarantee. If  ...

Rated power up to 500 kg/h engine power 3.0 (4.0) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 1200 mm width 640 mm 0 mm Hoehe Assumption 1250 mm Weight 115 kg Material 1.4301 / AISI 304 Connection for mash pump DN 65 AG Hoehe mash release 340 mm Hoehe stone ejection 380 mm ; New machine - best condition

capacity 90 l/h electric power 6 kW electric outlet 400V 50Hz (3 phases) fuse 16 A weight 10 kg material 1.4301 / AISI 304 suitable for fruit and vegetable juices ; new machine - top condition

capacity 500 kg/h power 3 kW electric outlet 400V 50Hz (3 phases) fuse 16 A dimensions: length 1 200 mm width 640 mm height 1 250 mm insertion resp. discharge height 1 250 mm weight 115 kg material 1.4301 / AISI 304 mash pump connection DN 65 AG stone discharge height 380 mm mash discharge height 340 mm suitable for stone fruit, berries scope of delivery 5 mm screen ; new machine - top condition

Precision ball screw, D50mm, 1635mm, Rexroth, new As good as new in original packaging! The high quality part comes from a spare parts warehouse of a mechanical processing of a large car manufacturer, is completely as new and in the original packaging. Attention: We have many, in stock, high quality ball screws in different versions in the diameters 32, 40, 50, 63 and 83mm. Please have a look at our website of IPV GmbH. Ball screw, Type R151054395, D50 mm, 1635 mm, Fa. Rexroth, Ball screw diameter 50 mm, Pitch 20 mm, Length of thread 870 mm Length of ball screw nut 90 mm, Max. total stroke 780 mm, Total length of the spindle 1635 mm Diameter for coupling with motor 30 mm Diameter bearing seat A 40 mm, Functional guarantee! We cannot provide a conventional guarantee and warranty for second-hand parts. However, we give you a functional guarantee. If the unit does no ...

- for the standard boxes (LxWxH = 1200x1000x970) engine power 1.5 (2.0) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 1670 mm width 1460 mm He 1280 mm He Assumption 850 mm Weight 350 kg Material 1.4301 / AISI 304 Lifting force up to 550kg / Box Duration per swivel 15 sec. Maximum mash levy 900 mm width fruit delivery 500 mm ; New machine - best condition