alpin used for sale

Casing holder device ALPINA type DOE9 Manufacturer: Alpina Type: DOE 9 Supply: 400 V Casing holder device ALPINA type DOE9 Ask for offer iNTER-WiBA Sp.J. UL. Krakowska 263 PL 43-305 Bielsko-BiaÅ?a USt-IdNr.: PL547-17-47-669 Tel. 0048/33 812 58 60 fax. 0048/33 812 58 36 abc.inter wiba.com.pl

Bobst Cube / monitor with control unit for transfer station, Bobst Alpina 110 II matic. Used and tested. Bobst cube / monitor with control unit for transfer station, Bobst Alpina 100 II matic. Used and tested. BSA07320000TG / H12P+P50S1

Type: 100 FSG, Y&l: 1986, granulation plant with circular gas operation, sifter 100 ATP (4 kW Vario, up to 11,500 rpm), and reblow filter K 6 R (2.4 m2 filter area). All in stainless steel. Very good condition.

Double flat clip machine DKF 15/15 overhauled 2009 - see display category Packaging machines -

Material: steel Engine: 75 kW Pin-disk Capasity factor: F=ca. 6,3 Drive: 75 kw Speed: 4900 The machine is as good as new. You can also get the entire system with all components.

Weight 1750 kg Length x Width x Height 1800 mm x 1350 mm x 3000 mm Machine data: rotor diameter - knife circle : 500 mm length rotor : 630 mm angular speed rotor : appr. 650 min-1 after-run duration : appr. 60 sec. motor power - depent of order: 37 kW / 1500 min-1 45 kW / 1500 min-1 idle power :appr. 30 - 40 % of nominal power. Very good condition, ready to work. You can also get the entire system with all components.

Material: steel Engine 11 kW Very good condition. You can also get the entire system with all components.

Producer: Alpina Description: -Hopper capacity: 60l -Paddle rotor (teflon paddles) -Twister -Efficiency approx 300kg/h

Drive: 30 KW

Material: mild steel Drive: 45 KW Weight: 2000 kg Dimensions: 1500 x 1500 x 1600 mm

Used mill Alpine 500.

rpm : 6.300 Weight : 220 kg.

Fine grinding plant consisting of: Alpine 630 AFG fluidized bed counter-jet mill (V ges: 885 dm3, 10 bar pressure-shock-resistant, saerterrad fold-out), feed station, cyclone, 2 pcs. EX-protection valve, control cabinet and 4 pieces of product buckets. Previous use: Grinding of toner. The system can be inspected in a disassembled condition. Available at an additional cost: Dust filter Bühler PGFG 60/18 (39 m2 filter area).

Inlet size: 400 x 250 mm - With electrical motor

--> Grinding blades in the opposite direction. Suitable--> mill for the processing of spices. 2 drives: 15 KW + 7.5 KW.

Used hammer mill made by Alpine, type B 630. Manufacturer's documentation.

Kolloplex pin mill type 630 Z, Drive : 55 KW Weight : 1100 kg; --> Stifscheiben diameter housing and door side : 630 mm;

Stock - No. 2537 1 used,, functionally tested cutting mill/granulator Manufacturer: Alpine Hosokawa Type: RO 50 / 80 Built: 1993 Material feeding hopper: 500 x 840 mm Opening hydraulic Rotor diameter 500 mm x width 800 mm Rotor semi-open, 4 rotor V-cut - 2 Fixed blades Drive 55 kW Sieve diameter 10 mm Blower and Cyclone Throughput up to approx. 800 kg/h depending Material Machine is ready for demonstration from the Wuppertal plant, Date by appointment More granulators from stock ready to show, Ask for our current stock list or visit : plasticotrading

turning diameter over bed: 330 mm turning diameter over slide rest: 190 mm centre distance: 650 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m turning length: mm 3-jaw chuck Multifix tool holder device tail stock coolant device Technische Daten / technical details: Spitzenweite / center to center 650 mm Dreh-Ø über Bett / turning diameter over bed 330 mm Dreh-Ø über Schlitten / turning diameter over sledge 190 mm Spindelbohrung / spindle hole 36 mm Drehzahlbereich / spindle speed 30-2500 UpM /rpm Antriebsleistung / drive capacity 2,2 kW Gewicht der Maschine ca. / weight ca. 600 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Nautical vacuum dryer Nautical vacuum dryer Hosokawa Alpine

Mill, Used Machine Type : B 315 Manufacturer : Alpine

Mill, Use Machine Type : B 315 U Manufacturer : Alpine Material : Mild steel

Vacuum cutter Alpina PBV 330-1110 DC Manufacturer Switzerland Year of production Overhauled Technical data overall dimensions 3300x2600x2450 mm; bowl 330 ltr; power supply 400 V, 50 Hz; total power 115 kW / 150 A; knives speeds 550/975/1950/2500/3200/4100 rpm, main motor 103 kW DC; bowl speeds 4/8/12/16 rpm, bowl motor 1,2 kW; mixing speeds 65/130 rpm, hydraulic system 5,5 kW; loader; unloader; vacuum pump Busch 250 m3/h, 5,5 kW; weight 5600 kg.

Mill, Used Machine Type : B 315 Manufacturer : Alpine

Fine impact mill B 315 with 15 kW motor, newly mounted

Cutter Manufacturer: Alpina Made of stainless steel Volume: 200 liters

Machines No 53423, 5.5KW incl. soundproof booth

Height 2300 mm Width 2700 mm Length 2200 mm Weight 5000 kg Power supply: 400V 50Hz 3N Total power 102 kW Main Material Stainless steel, acid-resistant Cutter Type Vacuum Bowl Cutter Cutter bowl made Stainless steel, acid-resistant Bowl capacity 200 l Number of knives on the head 6 pcs. Knife shaft speed 680-5050rpm Bowl speed 4-16 rpm

Height 1700 mm Width 1600 mm Length 2300 mm Capacity 300 l Power supply: 400V 50Hz 3N Total power 106 kW Main Material Stainless steel, acid-resistant Cutter Type Bowl Cutter Cutter design Stainless steel, acid-resistant Number of knives on the head 6 pcs.

grinding diameter: 480 mm grinding length: 2250 mm centre height: 370 mm throat: 900 mm length of gap: 400 mm bed width: 480 mm turning speeds: 14-1000 U/min spindle passage: 85 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Used Alpina clipping machine type DKF 18.15. Technical data: Voltage 380 V Number of phases 3 Frequency 50 Hz Pressure 8 bar

Wide-chamber pin mill with grey cast iron housing, output / throughput: 600 kg/h max. (depending on material), required motor power: 12 kW to 22 kW (optional). Rotor and stator disc in very good condition. Cleaned, anti-rust primed and repainted. Rust protection inside can be easily removed before commissioning.

A complete UPG system for polyester resin granulate production is available. 1) High-speed Henschel fluid mixer FM 350C, speed: 1500 rpm, heating unit: Lauda. 2) Raw material supply system with 6 bunkers, screws and vibrating chutes. 3) Conveying system with a collecting tank located 9m above the mixer and a Demag 4t rope hoist. 4) Schenk fluidized bed cooler. 5) Engelsmann ED 250/4 flat bed screen. 6) Alpine B40/63 RO granulator. 7) 2 annular gap compactors Siemens. 8) 2 Kessler & Luch blowers, volume flow: 7000m³/h. 9) Aerobic filter, filter capacity: 4000m³/h. Documentation available. On-site inspection is possible.

turning diameter: 570 mm turning length: 2000 mm control: Siemens Sinumeric steady: chip conveyor: turning dia. in gap: 600 mm turning diameter over slide: 340 mm spindle bore: 63 mm Tool changer: total power requirement: 22 kW weight of the machine ca.: 4,5 t dimensions of the machine ca.: 3,5x1,5x1,5 m The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad ...

A complete Hosokawa mill for processing polyester resin lumps is available. Complete plant: Feed material: polyester resin, max. feed grain size (dry): 800mm/600mm/20mm-30mm, fineness: below 1.5mm, round hole diameter: 15mm, plant capacity: approx. 3000kg/h, analysis method: Alpine air jet screen 200 LS-N. 1) Alpine single-shaft shredder type A 1500P, feed hopper opening: 2030mm/1440mm, feed hopper volume: 2.5m³, working width: 1500mm, knife circle: 300mm, rotor speed: 100rpm, motor power: 37kW, machine dimensions X/Y/Z: approx. 2100mm/2200mm/2300mm, weight: approx. 3500kg. 2) Automatic dedusting filter AE 48 L, filter surface: 42m², filter bags: Needle felt 550g/m². 3) Alpine Compact-Line granulator 45/100 CL, cutting tool rows: 4, min. hole width: 3mm, required power: 55kW. Including extraction system, conveyor system and accessories/peripheral equipment. Documentation available. On ...

Stiftmühle Alpine 630 C, dismantling provided by the buyer.

Alpine pin mill A 400 CW. Mining by the buyer is required. 2 x available

Hammer mill Voest Alpine Unirotor 490/190. 2 x available.

Additional knives will come with machine.

300 lit, good condition

Center height: 280mm, center width: 2000mm, turning length: 2000mm, turning diameter over bed/face slide: 570mm/340mm, spindle bore: 63mm, speed: 2500rpm, quill stroke: 160mm, quill diameter: 70mm, power requirement: 15kW. Machine dimensions X/Y/Z: approx. 3850mm/1850mm/1750mm, weight: approx. 3500kg. On-site inspection is possible.

Annpona Cutter PB 125-990, with Black Bowl, in Function

Alpina-Clipper Model DK

Technical data of the pallet rack crossbar: Shelving system: Voest Alpine Type: Megastar GS The scope of delivery includes: 01x Pallet rack crossbar, used Material colour: hot-dip galvanised CS profile: 100 x 50 x 10 mm Agraffe: 4 HK (hooks) Clear width: approx. 2,700 mm 02x Locking pins, used Design: compl. galvanized For securing the longitudinal members Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. Any additional transport or shipment of this item is associated with additional costs, which can be requested separately depending on the delivery location or scope of delivery.

Vacuum cutter Alpina Swopper Sw V 330 S

ALPINA TIPPER TIE SW 330 CUTTER AS NEW

General SKUR0380 LocationBarneveld MakeAlpine Ultraplex Type500 UP beater plate No.141724 Year of construction1970 Main Features Motor30 KW Inlet diameter450 mm Width150 mm Specified Features - Fine Impact Mill MaterialMild steel Fine Impact Mills Grindercheck Grinding room sizedia. 450x150mm Inlet170x100mm Motor30 kW 400 Volt Information Total height1,1 M Weight1020 Kg Floorspace1,1x0,9 MFine Impact MillsAlpineMills > Fine Impact MillsBrand > Alpine What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!