40 bar used for sale

Atlas-Copco GA11P FF 9,8 bar Diesel-oil (1) -- Naphte (2) -- Electr (3): electric Low press. (1) High press (2) Screw (3): 9,8 bar Volume flow rate: 1,82 m3/min Power imput: 11 kW Length: 1260 mm Width: 720 mm Height: 1480 mm Weight: 455 kg

NEW! 400 L capacity all stainless steel with stirring system conical bottom with centrifugal pump with water meter power : 1,5 kW dimensions (l x w x h) : 1.200 x 700 x 1.500 mm

NEW! flaker for frozen products (fish, meat, vegetables, etc...) electrical power : 11,5 kW dimensions of the machine (l x w x h) : ± 2.100 x 1.070 x 1.300 mm capacity : ± 2.500 kg / h for blocks of max. ± 470 X 600 X 200 mm 3 x 400 V

Glass Triblock KOSME Modell Barifill RFC Filling System: Short Tube Filling System with 60 filling valves, 50 rinsing stations and 10head aluminum screw capper Year of manufacturing: 2013 Capacity: 0,33 ltr. glass bottles - 20.000 bph 0,75 ltr. glass bottles - 16.000 bph Pitch: 113 mm Control system: Siemens S 7 The complete line was fully refurbished in December 2025. Available from November 2026

GINES, Barcelona 800mm wide x 350mm dia two roll mill, Machine number: 88, manual nip adjustment, adjustable guide plates, friction ratio 1:1.18, direct drive gearbox (on left hand side), with 60HP DC variable speed motor, Mentor II DC drive control panel. O/a dimensions 2750mm x 2100mm.

VakuuCar +. Modern mobile work station with vacuum clamping device and height adjustment. Set your workstation to your workpiece. Size 1200 x 800 mm Height 850-1,050 mm Flat suction pad round, India. 190 mm elongated 280 x 80 mm Weight 115 kg VakuuCar +. Modern mobile work station with vacuum clamping device and height adjustment. Set your workstation to your workpiece. Size 1200 x 800 mm Height 850-1,050 mm Flat suction pad round, India. 190 mm elongated 280 x 80 mm Weight 115 kg G & BAR-BV-1 Optional equipment: Swing frame, additional cleaner, vise, Extensions Drawers & BAR-BV-08-74 Accessory tray G & BAR-BV-08-78 Optional equipment: Swing frame, additional cleaner, vise, Extensions Drawers & BAR-BV-08-74 Accessory tray G & BAR-BV-08-78

Oven wild Barfield Temperature: 500 ° C Dimensions: Inside dimensions (WxDxH): 470 x 440 x 400 mm External dimensions (WxDxH): 850 x 600 x 730 mm Supply: 380 volts

Temperature: 500 ° C Dimensions: Inside dimensions (WxDxH): 470 x 440 x 400 mm External dimensions (WxDxH): 850 x 600 x 730 mm Supply: 380 volts

Board repair line with double end profiling line in top condition Workpiece parameters of the plates: Min.: 900 mm x 200 mm Weight min. : 17 mm Max .: 5000 mm x 1250 mm Max. Weight: 60 mm Weight: max. 150 kg < Accuracy: +/- 0.2 mm The portals have a max. Clock power of: max. 6 cycles / min The max. Partial performance: 18 parts / min (DEP line) Year of construction 2008 Condition: good (Original price of the line 2008 Euro 4.9 million) Consisting of: Feeding station with feeding rollers, Automatic vacuum lifting table for lengths up to 6 m Conveyor systems Repair line 1 Turning station Transfer service Repair line 2 automatic vacuum lifter for stacking (6m) Stacking roller conveyor Control cabinet with machine control Profilfraessanlage Stacking Tables; very well

REX - TORWEGGE - HOMAG- BARGSTED - KALFASS - HOMS-410-K core layer production plant (also solid wood boards) Consisting of feeding roller, Package cross-cut saw HOLTEC's 121-SHKA,. more feed roller TRANSA, Rotary scissors type lift roller Solid wood loading portal, Loading system KALFA for planing machine REX, REX planing machine HOMS-410-K built in 2004. with RIP saw unit. Central RIP saw unit, upper and lower drum, Much sheet saw unit, Belt conveyor system 8 manual workstations circular saws, 12 x material import System. 12 x glue system. Glue press TORWEGGE Working length approx. 6600 mm,. 2 cross cutting, 8-speed The stack and cooling system, Stacking line, Conveyor roller conveyor Power 2500 sqm / 7 hours PLATTENAUSBESSERUNGS AND ROLL FORMING LINE BARGSTEDT/HOMAG Plattenausbesserungs line Doppelendprofilier line in TOP condition! Workpiece parameters of ...

Barsso” vacuum tumbler Type 5 Bartumb NEW ! all stainless steel PLC control with 50 programs max. load : ± 500 kg adjustable speed from 0 up to 9 rpm with vacuum pump Büsch with water filter dimensions (l x w x h) : 2.550 x 1.300 x 1.650 mm

Horizontal pillow-pack packaging machine For the packaging of various products from A for Apple to Z like plums, the performance is dependent on the product and the cover material (foil) that are used to. Is the machine for packs of 20 to 50 wraps the minute set there are various special applications possible or additionally possible. Depending on customer request, the machine in a line can be built or supplied as a whole line. From the Eintaktung.Bis to the Pack in the box or E 2 box with Etieketierung and foreign body detection.

VakkuCar3 Bench Planer Modern mobile workstation with vacuum clamping device and height adjustment. Make your workplace on your workpiece. Vacuum flat suction; d = 190 mm Flat suction pad 250 mm x 80 mm Flat suction 240 mm x 45 mm built-in socket for auxiliary equipment Size 1800 x 800 mm Height-adjustable 874-1074 mm G & FE-VAKUUCAR-3 Extras: Swing frame, additional cleaner, vise, Extensions Drawers & BAR-BV-08-74 Accessory tray G & BAR-BV-08-78

Cooling screw trough screw double-walled heated or coolable used Manufacturer: BARL Maschinenbau GmbH Type: KT0803F17T50 Built: 2015 Total dimensions of the trough screw approx. 9.5 x 1.3 x 1.6 m Trough length approx. 8000 mm Trough width outside approx. 450 mm Trough depth approx. 600 mm Conveyor length approx. 7000 mm partly double-walled and can be heated or cooled with water Steel screw with cooled shaft Spiral thickness approx. 8 mm Diameter approx. 400 mm Spiral height approx. 100 mm Slope approx. 160 mm Shaft approx. 200 mm geared motor 1.5 kW 6.8 rpm 220/380 V substructure Steel construction approx. 11 x 2.5 x 0.2 m Total dimensions: approx. 11 x 2.5 x 2 m Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.

new ! all stainless steel 2 speeds (30 and 60 rpm) 2 mixing directions 2,4 kW safety lid CE-approved overall dimensions (l x w x h) : 1.720 x 840 x 1.390 mm (open lid: H: 1.890 mm)

all stainless steel capacity 300 L. (= ± 10CF) Double Ribbon mixing arm Dimensions: (l x w x h) : ± 1.900 x 670 x 1.740 mm (open lid : ± 2.140 mm) outfeed height : ± 720 + 20 mm safety lid CE-approved 2 speeds: 16 en 32 rpm 2 mixing directions 5,5 kW Digital – touch screen with programs Perfectly suitable for dry products, such as: herbs, ingredients, powders,…

new ! all stainless steel 2 speeds (20 and 40 rpm) 2 mixing directions 12 kw pneumatic lid inspection gantry safety lid CE-approved overall dimensions (l x w x h) : ± 2.210 x 1.130 x 1.770 mm (open lid : ± 2.630 mm) infeed height : ± 1.600 mm outfeed height : ± 720 + 20 mm + Loader for eurobins

new ! all stainless steel 2 speeds (20 and 40 rpm) 2 mixing directions inspection gantry safety lid CE-approved variable speed plc control overall dimensions (l x w x h) : 1.970 x 1.000 x 1.600 mm (open lid: H: 2.250 mm) Quick & Clean system Seals of mix axles easy and quickly disassembly and monolithic seals + Loader for eurobins

BARATTI FRAMED VACUUM PUMP WITH SUCTION FILTER AND SILENCER Fabr. -No.: 216 105 // Type: ATMOS V4-KR Var. 0102 Equipment / Additional information: Roots Blower Section. oil and wear-free compression, air-cooled, V-belt drive with tension rails and belt guard and two-stage exhaust silencer Incl. the following accessories: -Vacuum relief valve -saugs. Fine filter 3" -Connection piece internal thread 3" - Rohrfederman. -1..0 bar, filled with glycerine -Drive motor Blower data: Max. negative pressure: 500 mbar, abs. Suction volume: 440 m3/h Fan speed: 2920 rpm Noise level: approx. 79 dB (A) Engine data: 7.5 kW, 2930 rpm, 400/690 V, 50 Hz, IP 55 ISO class F, B3, KKL

Take-up Winders for synthetic Yarn Barmag POY / FDY filament yarn high speed take-up winder, SW4 type with 2 bobbins Chuck length: 600 mm Chuck type: 2 bobbins Chuck dia: 75 mm Stroke length: 250 mm max package dia: 305 mm MAX MECHANICAL SPEED 6000 M / MIN, WITH DOUBLE-DECK ARRANGEMENT AND PITCH 410 MM

We can offer you 5 x Barmag FK6-1000V texturizing machines,manufactured in 2019,240 spindles,with spandex(lycra) device,still working,good maintenance. We machinery dealer of Polymwerization,POY,FDY,DTY,Staple,Nonwoven amd spare parts. We have many brands and models machines, tell me what you need seriously!

new ! all stainless steel speed : 27 rpm 2 mixing directions safety lid CE-approved power : 2,2 kW overall dimensions (l x w x h) : ± 1.400 x 1.000 x 1.600 mm

Bartell FSW-409 7/8in bead winding machine suitable for PCR tyres 12in to 20in consisting of: - 12 station bead wire let of unit. - Prodicon zig zag cutter Type Z/Z year 1988 (takes sheet compound max 750mm wide and cuts to suitable size for feeding extruder. - 60mm dia coldfeed extruder, L/D ratio 13:1, with 18.4kw DC variable speed motor and 3 x TCU's - Festoon section - Former unit with various Bartell formers available/included. - Siemens S5 plc controls.

Lmacchia Barley twist lathe- model012/FE Spiral/rope turning lathe Barley twist with automatic indexing 67" max. length 8" max. working diameter as new condition...$9,500 obo Contact Fred (716) 433 4224 (12:00 noon is best time to call)

new all stainless steel discharging height ± 1.770 – 2.250 mm mobile

NEW ! all stainless steel suitable for eurobins of 200L discharging height : ± 700-900 mm 1,5 kW mobile ± 300 kg dimensions (l x w x h) : ± 1.800 x 1.100 x 1.300 mm

NEW! industrial shredder for pulled meat suitable for beef, pork, lamb, chicken,… content hopper : ± 35L electrical power : 1,47 kW capacity : ± 300-500 kg / h (depending on the degree of the cooking) possibility to place a 200 L eurobin at the bottom of the machine, so the product falls in it.

BARMAG POLYESTER EXTRUSION -SPINNING LINE WITH 12 POSITION / 72 THREADLINES FOR POLYESTER POY MICROFILAMENT YARNS • MANUFACTURER : BARMAG , GERMANY • CONSISTING OF FOLLOWING EQUIPMENT : •1 EXTRUDER BARMAG 12 E 8•SPIN BEAM INCLUDING SPIN PACKS & SPIN PUMPS3,5 CC/U•SPINNERETTES 100MM DIA, BOTTOM LOADED,DESIGNED FOR HIGH COUNTS MICRO & SUPERMICRO•POLYMER MANIFOLD EXTRUDER TO SPIN BEAM•DOWTHERM MANIFOLD FOR SPINBEAM ANDPOLYMER MANIFOLD•QUENCH SYSTEM INCLUDING FINISH SYSTEM,SPINFINISH JETS BY 'KYOCERA'•WITH CONVENTIONAL QUENCHING CABINETS +EVOSEPEED & RADIAL TYPE •TAKE UP UNITS, INCLUDING:•TAKE UP SECTIONS / PLATFORMS / LADDERS•COLD GODETS, ONE PAIR PER POSITION•INTERLACE SYSTEM WITH HEBERLINE INTERMINGLING JETS•YARN SUCTION SYSTEM•12 WINDERS, BARMAG CW6-1200/66 ENDS PER CHUCK , max. dia 440mm, stroke 170 mm

Hot counter + refrigerated counter on undertable with casters Dimensions undertable: H95 x W193 x D76 cm Hot Counter BETEC Execution: Hot counter GN 2/1 230V / 50 Hz Heat output up to 90°C the hot counters are lit up Total dimensions: H55 x W75 x D78 cm Year of Make: 2019 Chilled distribution depot: Bartscher Batida 2/1 Refrigerated display case / cold counter 2 x GN 1/1 with squared glass version 406051 This refrigerated display case / show display case from Bartscher is a guarantee for your good product presentation. Dimensions (W/D/H) cm: 75 x 77.5 x 60 cm Weight: 78.6 kg Capacity: 1 x GN 1/1-6.5 cm height (53x32.5cm) Technical services: Temperature range: +6ºC / +10ºC Version with convection cooling including lighting Connection: Connected load: 230 V /0.29 kW 1 phase / 50 Hz / 16 A with plug in Schuko design ...

Type Barmix 300 New! complete stainless steel 2 speeds (20 and 40 revolutions per minute) 2 rotation directions 3.3 / 4.4 kw fold-up inspection stairs Safety lid Emptying forward via an emptying flap with CE marking Outer dimensions (L x W x H) : 1,750 x 950 x 1,650 mm (open lid: H: 2,100) Loading height ± 1,350 mm Dimensions Drum (L x W x H) : ± 860 x 670 x 565 mm

Type Bartumb New! MC control maximum load: ± 380 kg with vacuum pump "Busch" Dimensions (L x W x H): ± 2,200 x 2,100 x 2,500 mm stepless speed from 0 to 9 revolutions / minute a variety of products, as all varieties of salads, meat and fish, can be mixed /tumbled with the Bartumb. + With loading arm for standard car 200L

1 BARUDAN double head embroidery machine type BEAT-802T-YS, 2 heads, 7 needles each head, with driver unit SDV-I, BARUDAN SMT keyboard

We have complete Barmag POY spinning lines, YOM 2004, 2 kinds of widers, ACW 4T 1200/8, ACW 1500/10. each model 48 pos. available very good condition. Serious buyers contact us.

Key data: 150 mm

Berstorff Strainer Extrusion Line Consisting of: Extruder Supplier Berstorff Type GE 150KSx16D Year of construction 2007 Pins: 12 Pins per level: 8 Condition: good Weight approx. 10000 kg Screen change: hydraulic, bladder accumulator 20lt / 300Bar D = 200mm Gear pump Supplier: Maag Pump Systems Type: extrex® 110-5 RV Volume 716 cm³ / rev Year of construction 2013 Condition: good Heaters Supplier: Regloplas Type P140 Year of construction various Number 5 pcs. Cooling bath Cooling medium Water above, 2 rows below with 4 fans each Year of construction 2006 Condition: good Dimensions 9m Weight approx. 500 kg Especially 8 fans Installation tape Year of construction 2006 Condition: good Weight about 300 kg

BARCODE PRINTER / LABEL PRINTER CAB A4 + Equipment / Additional information: Printer method: thermal transfer / thermal direct Resolution: 203 dpi, 300 dpi or 600 dpi Print speed: 200 mm / sec (203 dpi), 152 mm / sec (300 dpi) Maximum print width: 116 mm Interfaces: USB 2.0, RS232, Ethernet 10/100 Base T, 2x USB master interface, slot for CompactFlash memory card

Bartscher combi steamer for 2/3 GN shells, with core temperature probe, with 3 flat 2/3 GN shells and 3 deep 2/3GN shells (see photos), 4 shells of which are new. Current: 230V/50Hz, 2.5 KW with operating instructions

Barwell MR400 Top Load Ram Extruder

Bartscher refrigerated table 0 °C to 10 °C 1 unit – double benefit: convection cooling ensures a constant and uniform cooling temperature inside the refrigerated table with 1 door and 4 drawers. With its high-quality and robust stainless steel surface, the appliance can be perfectly integrated into any kitchen and can also be used as a work surface. • Number of drawers: 4 • Door hinge: Left • Door Type: Hinged Door(s) • Number of doors: 1 • Number of cabinets: 1 • Cabinets refrigerated: Yes • Drawers refrigerated: Yes • Standard format drawers: 1/1 GN • Connected load: 0.452 kW | 230 V | 50 Hz • Feet height adjustable: Yes • Temperature range: 0 °C to 10 °C • Height adjustable: 850 mm to 900 mm • Backsplash: 50 mm • Cooling: Convection • Refrigerant: R134a • Digital Display: Yes • Depth GN container max.: 150 mm • On/Off S ...

machine measurements: 850 x 1.800 x 1.450 mm machine weight: 360 kg power capacity: 0,7 kW Condition: new Specification: Powder coating machine, type: EPC-30/2E The machine is designed for the powder coating of cables, hoses and profiles. - Product diameter max.: 30 mm - Product speed max.: 1,500 m/min - Powder throughput min.: 30 g/min with fine dosage - Powder throughput max.: 400 g/min per powder injector - Electrostatic: available as option - Connected load: 0.7 kW - Dimensions LxHxW: 850 x 1,800 x 1,450 mm - Weight approx.: 360 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

cross-section width:: 100 mm cross-section heigth:: 40 mm feed:: 2 - 999.999,9 mm Condition: new, Specification: Impact knife cutting machine CC-600/40 for hoses and profiles - contact length: 600 mm - product diameter: 40 mm - belt width: 100 mm - Tractive force: 400 N to 800 N - Drive: 2 drives upper and lower belt - Conveyor belt speed: 100 m/min - Drive feed, cutting motor: Servo drives - Cutting capacity with blade max.: 4,000 1/min - Connected load: 3.5 kW - Dimensions L/H/B: 1,900 x 1,650 x 960 mm - Weight approx.: 580 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

We can offer Barmag FDY lines, winder model: ACW-5T, 1380mm/12 ends, hot godets model HF6, All ground floor equipments, just dismantled into warehouse.very good condition.Serious cintact us.

The Lutetia Type 1 sous vide churn is aimed at food professionals who require high marinade quality and production performance. Indeed, this model can process up to 400 kg of meat and brine per cycle, making it a perfect solution for medium-sized workshops. In addition, the 950 liter tank volume ensures a comfortable margin for vacuum marinating operations, while ensuring repeatability of results and consistency of processing. Thanks to its compact design (2150 × 1230 × 1730 mm) and a weight of approx. 800 kg, this churn easily fits into an existing production line. In addition, vacuum technology improves brine absorption, enhancing the texture, taste and added value of the finished product. For example, the internal components and robust workmanship ensure a longer service life, while the quick integration and simplified maintenance reduce production downtime. In addition, the L ...

The Lutetia T2 churn is a benchmark machine in the field of vacuum mixing. Designed to meet the needs of meat and food processing plants, it offers a capacity perfectly suited to medium-sized productions. This ensures an ideal balance between performance and space. Thanks to its homogeneous mixing system, the T2 Churn optimizes marination and improves the texture of the products. This is because the vacuum process promotes uniform brine penetration and reduces yield losses. In addition, it preserves the quality of the meat by limiting oxidation and improving preservation. This efficiency makes it an essential tool for manufacturers wishing to produce with regularity and consistency. In addition, its robustness and stainless steel design ensure optimal durability. Food contact surfaces meet the highest hygiene standards, simplifying cleaning and maintenance. In addition, its footpri ...

The Lutetia T4 vacuum churn is an essential tool for meat processing companies looking to optimize the quality and efficiency of their processes. Thanks to its high-performance vacuum system, this churn ensures homogeneous absorption of liquids, which improves the texture and flavor of the finished products. In fact, it allows you to marinate large quantities of meat efficiently, guaranteeing consistent and high-quality results. In addition, the Lutetia Type 4 Churn stands out for its robustness and ability to meet the demands of intensive production environments. With a high mixing capacity, it is perfectly suited for large productions, while ensuring a smooth and fast work process. In addition, it can be easily integrated into different production lines, offering great flexibility in terms of managing the volumes and types of meat processed. In short, the Lutetia Type 4 Churn is  ...

The Lutetia Type 5 vacuum churn is a must-have tool for food industry professionals looking to improve the quality and efficiency of their processing processes. Designed for processing large quantities of meat, this churn optimizes marinating and seasoning with its vacuum operation, ensuring even absorption of liquids and spices. This machine is equipped with a timer with variable speed drive, which allows each cycle to be customized according to specific production needs. As a result, it delivers consistent results while optimizing processing time. Thanks to its large capacity of 3800 to 4000 kg of meat and brine, the Lutetia T5 is particularly suitable for intensive production environments. Its robust, stainless steel design ensures exceptional durability and maximum hygiene, essential in food processing processes. In addition, its variable speed control allows precise control of th ...

Barwell Hydraulic Extruder – Used For sale: a used Barwell hydraulic extruder, designed for processing rubber compounds and elastomers. Barwell machines are well known worldwide for their robust construction, reliability, and consistent performance in industrial applications. The machine has been operated in an industrial environment, regularly maintained, and remains in good technical condition. Ready for further use after installation. Key features and advantages: Hydraulic drive ensuring smooth, stable, and precise extrusion Heavy-duty, solid construction for long service life Reliable operation, even with demanding rubber compounds User-friendly operation and easy integration into existing production lines Proven Barwell quality, widely trusted in the rubber industry Applications: Extrusion of rubber profiles and semi-finished products Preparation o ...