2000 kw gas used for sale

Maurer FKS 2000 Apollo boiling kettle, electrically heated in a glycerine bath, 200 liter capacity, external MC control and control box, with boiler float, core temperature sensor, replacement cover gasket, Connection 400V, 16.9kW, boiler inner dimensions LxWxD approx. 91x53x45cm, Total dimensions LxWxH approx. 140x84x102cm, weight approx. 390kg, Built in 1999, but hardly used, top condition, almost as new, checked by the bricklayer.

General SKU331S605 LocationBarneveld MakeBrabender (D) Specified Features - Viscosity test machine Variable speedcheck Speed5-120 rpm With computerDell With extruder(1x) With double screw extruder(1x) TypeDSK 42/7 Screw dia.42mm L/D7 Number of heating zones:3 Information TypePLasti-Corder 814400 / PL 2000 No.911021 / 901455 Floorspace1,7x0,7 M Total height1,6 M Weight500 Kg Extra Specificationsworking condition tested Viscosity test machinesBrabenderPlastic machinery > Viscosity test machinesBrand > Brabender What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

This 3-axis Nicolas Correa Euro 2000 was manufactured in 1997. It features a Siemens 840 D control system and a Ganfior electro-spindle capable of reaching 10,000 rpm. The working envelope is 2000 × 1250 × 700 mm with a spindle taper of SK40. It supports a maximum table load of 4,000 kg and weighs 13,000 kg. If you are looking to get high quality milling capabilities consider the Nicolas Correa Euro 2000 machine we have for sale.Contact us for more information.

Key data: 2500 kN

Krauss Maffei KM 250-2000 CX Blue Power with the Sepro Industrial Robot SR S5-35HL S4 Trans robot Year of Make: 2019 Injection unit: Screw diameter: 70 mm Spraying weight: 980 g Spray pressure: 1877 bar Dosing volume: 1077 ccm Clamping unit: Clamping force: 250 t Tiebar spacing: 630x630 mm Size of the clamping plates: 995x1050 mm Ejector: hydraulic Clamping unit: hydraulic Control: MC6 - Touch Screen Additional equipment: Very good technical condition Operating hours: approx. h in automatic mode Euromap 67 Robot interface Air Valve with Vacuum Measurement x 1 Air Valve x 1 Hydraulic core pull x 3 Air Core Pull x 1 Control with hot runners x 16 Hardened injection unit - Bimetal Energy-efficient machine – has a system with 3 hydraulic pumps with variable power Parallel movements Proportional valve on the injection unit – precise injection Additional  ...

Block size press Müro A3 2000/TM; cleaned and tested; Tabletop device; 2 dryers; insertion width 525mm; Insertion height 200mm. Pading press Müro A3 2000/TM; cleaned and checked; two heaters; working width 525mm; working hight 200mm.

General SKU224T211 MakeErnst Möschle (DE) LocationBarneveld Pressure Working pressure5 Bar Main Features MaterialStainless steel Volume2000 Ltr. Pressure5 Bar Specified Features - Pressure vessel MaterialStainless steel 1.4404, Stainless steel 1.4571 (316Ti) Capacity2000 Ltr. Vessel sizesdia. 1500x2200 Dished topcheck Dished bottomcheck Manholecheck Top connectionsdia. 50 mm (2x), dia. 80 mm, dia. 60 mm Outletdia. 50 mm, dia. 60 mm Information No.91 217 Year of construction1991 Mounted on legscheck Floorspace1,7x1,7 m Total height3 m Weight350 kg Extra SpecificationsWith CIP-nozzles Pressure vesselsMoeschleTanks > Pressure vesselsBrand > Moeschle What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The N ...

Horizontal milling center Type: HFZ 2000x1800x6000/444 Manufacturer: Heckert Year: 1983 Table: 1800 x 2000 mm Working length: 6000 mm Machine fully functional Find more here - / Contact us at -

Arburg 570C 2000-350/150 / Production line with the Arburg Multilift side robot / 2K machine Year of Make: 2003 Injection unit: Screw diameter: 40 mm Injection weight: 153 g Spray pressure: 2120 bar Dosing volume: 182 ccm Clamping unit: Clamping force: 200 t Handlebar spacing: 570x570 mm Size of the clamping plates: 795x795 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA Additional equipment: Production line with the Arburg Multilift side robot 2K Machine Air Valve x 1 Hydraulic core pull x 5 Control with hot runners Reinforced Injection Units – Bimetal Proportional valves on sprinkler units - precise spraying The vertical injection unit - screw diameter: ⌀25 mm - 49 g/hp All offered machines are started by our service technicians before they are sold. It is possible to receive a video of the technical tests of the selected machine o ...

Key data: 2000 kN

Arburg 570H 2000-800 e² / Hybrid machine / Production line with the Arburg Multilift Select robot Year of Make: 2011 Injection unit: Screw diameter: 50 mm Injection weight: 359 g Spray pressure: 2000 bar Dosing volume: 392 ccm Clamping unit: Clamping force: 200 t Handlebar spacing: 570x570 mm Size of the clamping plates: 795x795 mm Ejector: electric Clamping unit: toggle lever Control: SELOGICA - Touchscreen Additional equipment: Hybrid machine: energy-saving and very quiet Euromap 67 Robot interface Air Valve x 4 Hydraulic core pull x 2 Control with hot runners x 12 Hardened injection unit - Bimetal Main motor of the machine - Servo motor driven by inverter - Energy saving The injection unit is driven by the servo motor, which is controlled by an inverter Machine with cylinder / battery with compressed nitrogen (extra charge for fast working) Central lu ...

Used Used Case Sealer APE ch 2000 hm fl: Year: 2006 Condition: Good Used Case Sealer APE ch 2000 hm fl: Year: 2006 Speed: 2.000 pz/h Hot melt gluer Nordson ? Year 2019 Safety protections Code: C 79 More details: https://bottlingscout.com

Used Used Case Sealer APE ch 2000 hm: Year: 2001 Condition: Good Used Case Sealer APE ch 2000 hm: Year: 2001 Speed: 2.000 CPH Hot melt gluer Nordson ? Year 2018 Safety Protections Code: C 78 More details: https://bottlingscout.com

Hydropneumatic mode of operation Profile height: 200 mm under hold-down Max. Punch Height: 150 mm Wither height: 150 mm Weight: approx. 400 kg

Key data: 1350 mm, 3 , 120 mm

Weber LCE 2000 wide belt sanding machine with lift table loading ex site for sale.

Horizontal turning machine manufactured in 2008. This Weiler E70 / 2000 features a swing over bed of 720 mm and a maximum workpiece weight of 2,500 kg. It includes a steady rest, tailstock, and faceplate, providing versatility for various applications. With a spindle speed range of 1 – 1,800 rpm and a robust main drive power of 37 kW, this machine is designed for precision. If you are looking to get high-quality turning capabilities, consider the Weiler E70 / 2000 machine we have for sale. Contact us for further details.

- Complete machining with twin spindel, upper and lower turrets - Kitagawa 3 chuck left and right - Tool holders with driven tools axial and radial - Large jaws cabinet with inserts - OGL Gantry loader with ca 10 Kg load capacity - Chip conveyor - Paper Filtration Pressure Tank

Banding / Banding Machine ATS Tanner Type US 2000 LB With ultrasonic tape welding, suitable for plastic and paper tape with a width of 30 mm. Powerful, proven and universally applicable (see video below). Versatile, infinitely adjustable via two potention meters/rotary controls in terms of belt tension and belt length. Tape can be added later via pressure switches if necessary. Counter currently shows around 740,000 work cycles. Offer price 3000,- EUR EXW or 3,500 EUR incl. packaging & shipping with transport insurance.

This TORNOS DECO 2000-10 was manufactured in 1999. It features a loading magazine with drum, integrated hydraulic unit, and supports both front and rear with a center height of 1100 mm. It includes a movable headstock, directional spindle stop, and cross slide with tool holders. Ideal for precision turning, it operates on AC drive motors with an absolute measuring system. Contact us for more information about this machine.

cutting length: 2000 mm sheet thickness - max.: 6 mm operating pressure: 250 bar fabric-no.: S2669 weight of the machine ca.: 4,7 t working width: 2059 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Main Machine - ZERMA ZPS 2000 - Type: single shaft shredder (Einwellenshredder) - Drive power: 2 x 55 kW - Frequency converter: included (1 unit) Conveying Equipment Included - Discharge Belt Conveyor - Type: WF 4000 x 2500 x 580 - Drive: 1.5 kW - Inclined Belt Conveyor (mounted at shredder) - Belt width: 980 mm - Centre distance: 5000 mm - Belt type: PVC with cleats - Safety features: emergency stop rope and safety stop - Drive (right-hand): 1.5 kW Spiral Conveyor - Type: HS 450 NW 560 - Manufacturer: BULCOTECH - Drives: 0.75 kW / 11 kW / 5.5 kW / 11 kW Magnetic Separation - Drum Magnet (1 unit) - Overhead belt magnet: DM01.60 - Design: ferrite - Drive: 1.5 kW - For belt width: 600 mm Find more here - / Contact us at -

Brembana Helixchanger Heat Exchanger Notified body AIB VINCOTTE Pressure 4/10 bar Capacity 6600/3800L Hydr.press 7,5/14,3 bar

VALOREL Stainless Steel Vessel 620 Ltr. with propeller stirrer, allowed pressure 2,5/-1bar, max. temp 150C , on top there is a inlet 50mm for clamp connection, down outlet valve diameter 2"

A two stage tea and spice mixer Gebrüder Kerner with renewed control circuitry and wiring is available. Volume: 2000l, Material: steel, Drive power: 3.1kW, Control: Siemens. Without stand and feet. An on site inspection is possible.

9 assen: Y1 / Y2 / X / R / Z / V / X1 / X2 / X3 3 CNC-gestuurde frontplaatsteunen Capacity: 2000 ton x 14 meter Backgauge: CNC Control: 2D Touch Passage between uprights: 12470 mm Max stroke: 900 mm Max distance between table -- ram: 1600 mm Depth of throat: 1255 mm Table width: 800 mm Locking speed: 77 mm/sec Working speed: 9 mm/sec Returning speed: 85 mm/sec Electric motor (power): 2x 90 kW Length: 16835 mm Depth: 5695 mm Height: 6750 mm (above floorlevel) Weight: 370 ton Capacity: 2000 ton Bending length: 14 000 mm

The Velati M 2000 twin shaft paddle mixer is a robust and reliable industrial device, specially designed for food processing in commercial kitchens or production facilities. This type of used mixer is characterized by its high capacity and efficiency in mixing a wide variety of ingredients. Thanks to the twin shaft technology, the M 2000 ensures even mixing of the materials while minimizing mixing time. The paddles are designed to ensure optimal mixing without excessive friction, which maintains product quality. The stable construction of the device offers long-lasting performance and lower maintenance requirements. Ideal for use in food processing, this mixer is a valuable addition to any company that requires high-quality and consistent mixes., power: approx.: 1,600 kg mixing volume, Dimensions / weight: Mixer: L x W x H: 4,650 x 1,500 x 1,950 mm, auger: L x W: approx. 5,100 x 2,000 mm ...

In this case, the containers to be labelled are fed in by hand. The system was used for cylindrical jars with a low height. They are first given a base label from below, turned by 180° using a turning basket, and then given a security seal label from above. The labelled jars then run onto a storage table, offset by 90°.

A four-roll plate bending machine Kramer is available. Working width: 2000mm, max. plate thickness: 3mm, power: 3kW. An on-site inspection is possible.

x-travel: 1250 mm y-travel: 1000 mm z-travel: 1000 mm taper ISO: 50 Table dimensions: 650 x 1000 mm spindle speeds: 32-1600 voltage: 380 V Control: Philips total power requirement: 7,5 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

swing over bed - 500 mm distance between centers - 2000 mm

swing over bed - 500 mm distance between centers - 2000 mm accesories DRO Heidenhain

This 4-axis HEDELIUS RS 60 K - 2000 was manufactured in 2005. It features a generous X-axis travel of 2000 mm, Y-axis travel of 620 mm, and Z-axis travel of 520 mm. The machine can accommodate a maximum workpiece weight of 1000 kg on the fixed table. If you are looking to get high-quality machining capabilities, consider the HEDELIUS RS 60 K - 2000 vertical machining centre we have for sale. Contact us for further details.

plate width: 5000 mm plate depth: 2000 mm plate height: 400 mm total power requirement: kW weight of the machine ca.: 9,2 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CNC Turning and Milling Center Okuma LT 2000 EX -MY 2pcs Control: OSP-P300L Year of Make: 2013 Turning diameter over bed: 400 mm Center spacing: 960 mm Turning diameter: 210 mm Speed: 50 – 6,000 rpm Sub-spindle speed 50 – 6,000 rpm Travels: W-axis 730 mm X-axis 205 mm C-axis: 360 degrees (0.001) 2 tool turrets with 16 places each (all places driven) Equipment: - Chip conveyors - Paper belt filter system with high-pressure pump - 2x 3-jaw chuck Kitagawa - OGL gantry loader with approx. 5 kg load capacity - Stacking magazine 20 places - Touchsetter - Renishaw touch probe - Extraction system - Various accessories

Four Engel injection molding machines are available. 1) Engel ES 750/150 HL, year of manufacture: 2006, core pulls: 2, screw diameter: 55mm, shot volume: 511cm³, injection pressure: 1616bar/2052bar, nozzle stroke: 350mm, nozzle contact force: 67kN, clamping force: 1500kN, opening stroke: 606mm, ejector force: 60kN, ejector stroke: 150mm, min. mold installation height: 294mm, platen dimensions X/Y: 750mm/520mm, weight: approx. 9500kg, control system: CC100, operating hours: approx. 79000h. Including Engel HLi automation robot. 2) Engel ES 80/30 HL, year of manufacture: 1995, core pulls: 2, screw diameter: 22mm, shot volume: 38cm³, injection pressure: 1500bar/2050bar, nozzle stroke: 200mm, nozzle contact force: 28kN, clamping force: 300kN, opening stroke: 330mm, ejector force: 24kN, ejector stroke: 70mm, min. mold installation height: 110mm, platen dimensions X/Y: 550mm/380mm, weight: ap ...

turning diameter: 356 mm turning length: 510 mm control: M 730 BM total power requirement: 40 kVA weight of the machine ca.: 6,6 t dimensions of the machine ca.: m CNC control: Mitsubishi 730 BM Main spindle: Speed: 5000 rpm Power: 15/11 kW (15% duty cycle / constant) Bar diameter: 65 mm Sub spindle: Speed: 6000 rpm Power: 11/7.5 kW (25% duty cycle / constant) Turret: 12 stations Tool spindle speed: 10000 rpm Power: 5.5/3.7 kW (5 minutes / constant) Y-axis travel: +/- 50 mm Equipment: Machine with gantry loader: Left-hand installation, 14-station storage, 20-pallet workpiece storage, Double gripper conveyor 3-jaw hydraulic KITAGAWA power chuck, 210 mm diameter High/low pressure chuck system for main and counter spindles MABEO high-pressure pump with 1.5 MPa filter unit Coolant gun Coolant sprayer on the chuck for main and counter spindles Coolant sprayer for the machine bed cladding Oil  ...

Hydropneumatic mode of operation Profile height: 180 mm under hold-down Max. Punch Height: 145 mm Wither height: 150 mm Weight: approx. 400 kg

Hydropneumatic mode of operation Profile height: 180 mm under hold-down Max. Punch Height: 145 mm Wither height: 150 mm Weight: approx. 400 kg

Hydropneumatic mode of operation Profile height: 210 mm under hold-down Max. punching height with 2-way adjustable punching heads: 145 mm Wither height: 150 mm Weight: approx. 400 kg

Cream separator (Skimmer). Self cleaning. Machine comes with the bowl, motor (37 kW), motor cover, base plate and feet, desludge tank, control panel (original Westfalia), water valves, all inlet/outlet pipes with manometer / flowindicator and service tools for maintenance., Type of Machine: Cream Separator / Skimmer, Capacity: 20.000 liter per hour, Bowl speed: 4.700 rpm, Motor power: 37 kW - 380 V - 72 A - 1.475 rpm - 50 Hz - 3 Ph, Weight: 2.200 kg, Dimensions: 190 x 130 x 225 cm

- Spindle SK 40 - Speeds 8000 Rpm with 165 Nm - Workload 2000 Kg - ATC 56 Positions - Hours spindle 10.304 - Closed housing with automatic top door - IKZ Coolant system - LTA Air Cleaning

CNC vertical machining center Type: Mill 2000 Manufacturer: Chiron Year: 2013 Control: Siemens Sinumerik 840D Hours: 17000 X: 2000 mm Y: 700 mm Z: 550 mm Spindle speed: 9000 rpm Spindle taper: HSK-A63 Table: 2600 x 710 mm Max table load: 1000 kg Weight: 10700 kg Machine in good condition, fully functional, under power Find more here - / Contact us at -

turning length: 2000 mm greates pass round over bed: 630 mm swing diameter over slide rest: 350 mm control: Monforts Control System K bed width: 550 mm turning speed range: 2 - 1800 U/min spindle diameter in front bearing: 120 mm spindle head DIN 55027 - Size: 8 tool taper: RD2 PARAT quill stroke: 210 mm spindle bore: 71 mm total power requirement: 30 kW weight of the machine ca.: 5 t dimensions of the machine ca.: 4,90 x 2,10 x 2,00 m Three-jaw chuck / key bar / Ø250mm Four-jaw chuck 3-jaw chuck for tailstock 4-station tool post head PARAT Fixed steady rest, Ø small Fixed steady rest, Ø large Various chuck jaws, live centers, live centers, tool holders Chip conveyor with coolant pump The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

table length: 2000 mm table width: 1000 mm table height: 900 mm table load: 3000 Kg weight of the machine ca.: 0,45 t dimensions: 2,0 x 1,0 x 0,9 m Welding table / perforated table including accessory set WMT Basic-Set 2.0 The table is made of 25mm high-alloy, plasma-nitrided steel S355J2+N (St 52/3) Surface hardness 850 Vickers Surfaces that have been ground down and planed smooth. Hole diameter: 28mm, countersunk by 3mm 100 x 100mm grid Side panels 200mm Hole spacing in the side panels 50mm, diagonal grid Height adjustable from approx. 830 - 890mm Substructure reinforced with 140 x 15mm flat steel Including base bearings, 110mm diameter The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hanging cabinet HS 2000 with sliding door with intermediate floor Used device cleaned Dimensions: 2000 x 400 x 600 mm, WxDxH

Anchorage Rego SM 2000 M The machine when it comes to striking! Stirring machine with automatic timer Working Shaft/Agitator Shaft NEW Connection 400V, 16A-CEE plug Used machine overhauled with warranty

B&A REF: 9275 TON: 200 SCREW DIAMETER: 55MM SHOT WEIGHT: 451 STROKE VOLUME: 475CM3 INJECTION PRESSURE: 1741AR PLATEN SIZES: 780 X 780MM DBTB: 530 X 530MM MIN MOULD HEIGHT: 200MM MAX MOULD HEIGHT: 500MM MOULD OPENING STROKE: 440MM MAX DAYLIGHT: 940MM EJECTOR STROKE: 130MM CONTROLS: VPC 20000E AIR VALVES: 1 HEATING CAPACITY: 12.9KW

Key data: 2000 mm, 23 mm, 18 mm

4-roll plate bending machine Imcar-Italy capacity 2000 x18/23 mm year 1995, model 4RH12/3 , TECHNICAL DATA: Capacity plate width 2000 mm Plate thickness max 23 mm Prebend 18 mm Upper roll 300 mm Lower roll 300 mm Surface useful on rolls 2050 mm Electric 380/50 motor 11 Kw on centralized hydraulic unit Weight 10 Ton Machine dimension 4100x 1750 x H 1550 mm Configuration: Hardened rolls very high surface resistance Conical bending attachment Digital position readout Hydraulic rolls power driven with planetary gear unit Hydraulic side rolls on linear guideways plate prebend Open front drop-end hydraulic to unload the closed shell Safety and emergency installed

B&A REF: 9259 TON: 370 SCREW DIAMETER: 70MM SHOT WEIGHT: 1060 STROKE VOLUME: 1175CM3 INJECTION PRESSURE: 1700AR PLATEN SIZES: 1070 X 990MM DBTB: 710 X 630MM MIN MOULD HEIGHT: 300MM MAX MOULD HEIGHT: 750MM MOULD OPENING STROKE: 710MM MAX DAYLIGHT: 1460MM EJECTOR STROKE: 275MM CONTROLS: DIMI EL2 PLUS CORE PULLING: 2 AIR VALVES: 1 MOTOR: 37 HEATING CAPACITY: 27KW ROBOT INTERFACE: EUROMAP SCREW DRIVE: HYDRAULIC

Key data: 2000 mm, 6 mm, 10 mm

4 ROLL HYDRAULIC PLATE BENDING MACHINE MODEL M2006P _NC EASY COMMAND 15” -MATR. C072/25 MACHINE NEW PLATE BENDING ROLL PLANETARY DESIGN DOUBLE PINCH PRE-BEND BRAND MG SRL ITALY CNC_PROGRAMMABLE AUTOMATIC PLATE ROLLING Capacity: -Width of plate: 2000 mm -Thickness of plate rolling 6 mm -Thickness of plate pre-bending 4 mm Rolls dimensions: -Surface length mm. 2050 -Top roll  mm. 160 - Lower roll  mm. 140 Configuration installed: • Surface hardening of the four rolls, smooth finishing suitable for stainless plates rolling • Dual pre-pinch, plate edges pre-bend automatic programmable • Conical bending hydraulic attachment - hardened contrast pad. • Power driven rolls rotation top/bottom gearbox axial direct drive hydraulic each roll. • Calibration system f ...

Work table AT 2000 with beech wood top and sliding door Work table Baker's table mobile Beech wood worktop Used device cleaned Plate sanded & re-oiled

weight max. in kg: 2.000 kg table height: max. 1.010 mm table height: min. 190 mm table surface area: 800 x 1.300 mm engine: 0,75 kW The Unicraft SHT 2000 hydraulic scissor lift table (1300058) offers a reliable solution for your lifting projects, e.g., for manually feeding a planer or saw with entire stacks of wood. With an impressive load capacity of 2000 kg and a robust construction, this lifting platform is ideal for use in industrial environments. This scissor lift table is characterized by its precision and user-friendliness, enabling you to lift heavy loads safely and efficiently. With a maximum table height of 1,010 mm, the Unicraft SHT 2000 is the ideal choice for improving your workflows and protecting the back of the machine operator. Drive: Electro-hydraulic Cable length: 3 m Safety standard: EN 1570 Condition: New with warranty The data for this ad was created with ModulMW ...