200 kva man used for sale

Outdated MAN E2876LE302 bio gas engine in Exchange.

FOR SALE... 2 SET T/C TO TCR 18-42065 YOB 2010 AT TURKEY HAVE A GOOD DAY SIR. WE VE 2 SET COMPLETE T/C TO TCR 18 - 42065 AT OUR STOCK. PLS FIND TURBO CHARGER SPECT AT BELOW. TYPE: TCR 18 - 42065 WORK NO: 7642160 / 7642161 SPEED: 37300RPM T MAX: 650C. YOB: 2010 IF YOU INTEREST PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurluba BEST of regards; Aliaga marine services E mail: info@aliagamarine

FOR SALE COMPLETE MAIN ENGINE MAN BRONS 12V 25/30 HAVE A GDY SIR; WE VE COMPLETE BRONS MAN 12V 25/30 ENGINE AT OUR STOCK. THIS ENGINE EQUAL AS SULZER 12 ASV 25/30 ENGINE ENGINES ARE IN VERY GOOD RUNNING CONDATION. WE VE SO MANY NEW GENUINE SPARE PARTS AT OUR STOCK. ENGINES ARE READY TO LOAD ON TRUCK. PLS FIND SPEC OF ENGINES AT BELOW 2400Kw 900 RPM 1984 YOB 20604/1045147 SERIAL NO. IF YOU'VE ANY FURTHER QUESTIONS PLS DO NEED HESITATE TO CONTACT WITH US. Capt. Ayhan Ugurlubay Best regards; Aliaga marine services E mail: info@aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

MAN D 2066 LF 12 - Euro 4-287 KW - 390 HP Motor was cpl. repaired according to RAL GZ-797: with new piston rings, new bearings, new oil pump, AT cam shaft, AT injectors, new water pump, oil and fuel filters 1 year warranty without KM-limit Old Engine must be returned

MAN D 2066 LF 31 - Euro 4-324 KW - 440 HP Motor was cpl. repaired according to RAL GZ-797: with new cylinder liners, Pistons, bearings, turbochargers, air compressor, injectors, high pressure pump - without starter, alternator and clutch Repair enabled old part must be returned. Maximum mortgage of old part of 4.000,00 = €

Motor was sealed front and rear new - upgraded oil pump, thermostat, oil filter, fuel - engine was installed on engine test bench and a cpl. Test run was carried out 6 months warranty on the motor mechanism Mileage only 200,000 km old part pledge 4,500.00 = €

MAN D 2876 LF 13 - Euro 4-390 KW - 530 HP Motor was cpl. repaired according to RAL GZ-797: with new pistons and liners, new bearings, new oil pump, AT cam shaft, AT injectors, new water pump, oil and fuel filters 1 year warranty without KM-limit Bauglieches old part must be returned

MAN D 2866 LUH 24

MAN 2876 LE302 gas engine (biogas) 190KW (also as 210KW-Version) It's a replacement engine for various biogas CHP. Overhauled according to manufacturer guidelines and RAL quality seal(maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a quotation. We have other Exchange engines (2848 with 250KW and 2842 370KW) and AT cylinder heads, intercoolers, turbochargers, etc. and other components and spare parts for MAN gas engines in stock.

MAN 2848 LE322 gas engine (biogas) 250KW It's a replacement engine for various biogas CHP. According to one manufacturer guidelines and according to RAL quality seal repaired (maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a written offer. We have other replacement engines (2876 with 190KW and 2842 370KW) and AT cylinder heads, intercoolers, turbochargers and other components and spare parts for MAN gas engines in stock.

MAN 2842 LE322 gas engine (biogas) 370KW It's a replacement engine for various biogas CHP. According to one manufacturer guidelines and according to RAL quality seal repaired (maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a written offer. We have other replacement engines (2876 with 190KW and 2848 250KW) and AT cylinder heads, intercoolers, turbochargers and other components and spare parts for MAN gas engines in stock.

HAVE A GOOD DAY SIR. WE VE NEW UNUSED. MITSUI MAN NA 57 TO 725 P IT STOWED AT FABRIQ WOODEN BOX. IT WILL NEVER MOUNTED AND USED. PLS FIND SPEC AT BELOW. READY TO TRANSPORT. EX STOCK. MITSUI MAN: NA 57 TO 725 P NO.: 2430 SPEC AD: 490 A4K : 404.3 REVOLUTION: 15000 RPM MAX TEMP: 600 C IF YOU'VE ANY FURTHER QUESTIONS PLS DO EMERGENCY HESITATE TO CONTACT WITH US. READY TO TRANSPORT. EX STOCK. Capt. Ayhan Ugurluba Best Regards ; Aliaga marine services E mail: info@aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 ABC.aliagamarine.com TURKEY

The offer refers to the whole team. The MAN is as good as new and has only run 2093 kilometres. Net price: € 110.000,00. Manufacturer: MAN Model: TGL 8.250 Vehicle type: Truck box / suction-pressure vehicle Chassis number: WMAN12ZZ3LY404807 First registration: 07.04.2021 Next general inspection: 04.22 Mileage: 2,093 Displacement: 6,871 cc KW / HP: 184 / 250 Drive type: Diesel Euro6c Transmission type: Automatic Empty weight: 5,260 kg Permissible total weight: 7,490 kg Dimensions H / W / L: 3.35 m / 2.55 m / 6.15 m Equipment: Roller shutter / side doors / trailer hitch Maul / Air conditioning / navigation The offer refers to the whole team. The MAN is as good as new and has only run 2093 kilometres. The tank trailer has a capacity of approx. 10,500 litres with 3 chambers and is approved according to GGVSEB/ADR Class 3, packaging group III, tank coding LGBF and  ...

Mannesmann Demag compressor General repair 2004 Flow rate: 39.5 M ³/min, 2150 m ³/h Suction pressure: 1 bar Max pressure: 10 bar Speed: 1500 rpm Engine power: 250kW Pressure: 8.5 bar

MAN head, for engine 28/32 REVISED

approx. 500m roller conveyor with accumulating 50 cm wide, powered - used-: Price for 10m from the site: only EUR1.099.-(net), dismantled and loaded! Price for 50m from the site: only EUR4.999.-(net), dismantled and loaded! A total of approx. 500m available (details upon receipt in the camp)! Manufacturer: Mannesmann (Siemens) Dematic AG Type: KR Year of construction: 2001 Motor: SEW Individual lengths: approx. 3 m,. Width: 50cm, Conveyor width: approx. 44 cm, Roller spacing: approx 8 cm. Optional accessories (photocells, scanner etc.) Condition: good Available: available now Location: Camp Bautzen

2 x 3.6MW 60Hz MAN 18V28/32H Power Plant for sale At a time when the world is suffering from a shortage of power generation capacity, we are very pleased to inform you that we have a nice 7.2MW diesel power plant. This vintage power plant has been used as an emergency generating sets for a larger R&D center in Korea, a very short actual running hours (abt. 2000~3000hrs) and has been well maintained, so our company can confidently recommend this power plant to anyone who needs it. The plant was dismantled and has been now stored in our factory and will be delivered to the buyer after the performance verification test of the generating sets at our test shop. Main Specifications - Engine Model: SSANGYONG-MAN 18V28/32H x 2 Sets - Manufactured & Running Hours: in 1999 & abt. 2000~3000hrs - Continuous Output: 3600kW x 720 rpm - Frequency & Voltage: 60Hz & 6600V - Fuel Oil: Diesel Oil /  ...

7.2MW diesel power plant. This vintage power plant has been used as an emergency generating sets for a larger R&D center in Korea, a very short actual running hours (abt. 2000~3000hrs) and has been well maintained, so our company can confidently recommend this power plant to anyone who needs it. The plant was dismantled and has been now stored in our factory and will be delivered to the buyer after the performance verification test of the generating sets at our test shop. Main Specifications - Engine Model: SSANGYONG-MAN 18V28/32H x 2 Sets - Manufactured & Running Hours: in 1999 & abt. 2000~3000hrs - Continuous Output: 3600kW x 720 rpm - Frequency & Voltage: 60Hz & 6600V - Fuel Oil: Diesel Oil / Heavy Fuel Oil - Plant Auxiliary Equipment: 1 set

DEAR'S SALE, ALPHA MAN L&V 28/32 COMPLETE ENGINE & SPARE PARTS 12V CRANKSAFT STD 6L CRANKSAFT STD LINER, PISTON, FULL COVER, CONROD... ANY PARTS Brgds info@kscege.com

Dear's Sale, Man B&W 16/24 spare parts; Full cover, liner, pumps, conrod, crank&block(5cyl) piston, etc Best Regards info@kscege.com

Dear's Sale, Man B&W 40/45 engine parts Piston head full.. 2 pcs Liner 2 pcs valves etc Ready for transport Best Regards Hakan KUSCU info@kscege.com

S5 - used 50m³ / 50,000 litres steel tank, double-walled, underground tank, firefighting water tank, water cistern. In good condition, underground or aboveground tank, steel storage tank, water reservoir. Surface coated with bitumen insulation / bitumen painting. capacity: approx. 50m³ / 50,000 litres material: steel tank / underground tank, double-walled manufacturer: Mannesmann dimensions: approx. Ø 2.5m x 10.0m long weight: approx. 8.0 - 10.0 tons The steel tank is used, has been emptied and professionally cleaned inside. According to the age there are traces of use. This container can serve as a storage tank for water, waste water, sewage, manure, seeping juice, rapeseed oil, or as rainwater collection tank, water cistern, firefighting water tank etc.. Price upon request. Transport can be arranged at low cost. Also we can modify the tank to suit your dem ...

Cylinder heads for MAN 28/32 A-H for sale, Info by request Part no: 1.1616-03-E0

Ladies and gentlemen, hereby we offer a gas engine, type 2842E312 for sale on! The engine has 29.300 hours and is working properly.

We can offer 12 sets of Barmag winders,manufactured in 2022, model:Manta ACW6T 1500/16,16 ends,chuck length:1500mm.Never used,still in packing. Seious buyer contact us please. We have many brands and models machines, tell me what you need seriously!

sed Manesty Rotapress MK IIA rotary tablet press, 45 station, double sided, with pre-compression, keyed upper punches, With feed hoppers, force feeders, controls and associated parts.

Rotative tablet press of 27 stations Max. diameter of the tablet 16 mm Filling depth 18 mm Pressing capacity 80 Kn Prepressing capacity 20 Kn Production from 48.000 to 100.000 h Dimensions : 1.000 x 950 x 1876 . Weigh 1850 Kg. Force feeder Type of tool : B

Swiss type CNC Manurhin KMX TWIN 207 is a double-spindle automatic machine with automatic feeding of bars. The CNC lathe was produced in 2000 in France. Technical data : - type of automatic lathe: Swiss Type - control: NUM - Swiss control - number of axles: 6 - turning diameter up to: 20 mm - diameter of passage Ø: 28 mm - number of turns: 150-8000 rpm - feed: 10/15 m / min - number of tools: 8 + 8 + 4 + 4 pcs - spindle power: 2.2 kW - tailstock: counter spindle - machine weight: 5000 kg Lathe equipment: - two main spindles / two opposite spindles - material feed with FMB Doppel-Turbo - counter spindle: 150-6000 rpm - chip conveyor - Manurhin / Schlichting-System clamps - coolant filtration

Manitou Mod. MRT 1432 HOURS: 670 YEAR: 2004

Tablet output: 234.000/h (mechanical speed) Number of station: 37 stations Tablet diameter max: 25 mm Filling depth : 21 mm Die plate speed : 25 – 100 RPM Compression force max: 100 kN Initial compression force: 10 kN Type of tool : EU Norm D Height of the machine with filling hopper: 2135 mm Project floor area: 1260 x 1280 Weight: 2840 Kg

MANITOU MVT 1330 SL HOURS: 5,242 YEAR: 2001

N° of Stations 35 Output tablets per hour 70.000 - 210.000 Maximum tablet diameter 16 mm Maximum depth of fill 8.5 mm Upper punch entry 1.5 - 8 mm Die type B tooling Die diameter 30.1 mm Die height 22.22 mm Upper/lower punch length 133 mm Punch body diameter 19.05 mm Compression force 80 kN Power 3.75 kW Net weight 1143 Kg Can be also for doble layer.

Load capacity: 2500 kg

Manitou 170 AETJL aerial work platform with 16.90 m working height The 170 AETJ-L aerial platform makes it easy to reach the most remote work areas. Equipped with an articulated structure, this model is characterized by an exceptional offset and overhang to be able to work at different heights and in different places without having to move the machine. Take advantage of the flexibility of its hydraulic movements for precise positioning in the work area! With its perforated platform floor, inclination detectors and load sensors, cylinder valves and negative braking system, the 170 AETJ-L aerial work platform allows you to carry out your work safely. This machine complies with: European Directives: 2006/42/EC - Machinery (recast EN 280:2013) - 2004/108/EC (EMC) - 2006/95/EC (Low Voltage) Make: Manitou Type: Articulated telescopic platform Type: 170 AETJ Year of construction: 20 ...

with hood including fan with Gaer schrank 4 herds each 60x80cm long ago any stove with stone slab manual control with fixed water connection for each floor separately Each floor with separate swath box Fermentation chamber control manually Each floor with viewing glass Each floor with lighting Connection per stove 4.65 kW 400 Volt 3/N/PE 50 Hz Furnace is mobile on wheels checked and cleaned The furnace is fully assembled ready for loading in stock.

TABLET PRESS MANESTY BETAPRESS N° of stations: 16 Operating pressure: Max. 6.1/2 Diameter of punches: 19 mm Length of upper punch: 133.6 mm Length of lower punch: 133.6 mm Max. mechanical speed: 90.000 Height of machine: 160 mm Floor space occupied: 584 mm x 851 mm Approx. weight of machine: 695 Kilos

Mantle Packaging Stainless manual tray sealer, twin tray operation, temperature and timer controls, tray dimensions 270mm x 280mm, 1Ph