used DEMAG ergotech concept

Demag Ergotech Concept 110/470-600 Clamping/injection matrix Clamping force [kN] 1100 Mounting plate dimensions (hxv) [mm] 670 x 660 Clearance between columns (hxv) [mm] 470 x 470 Min./max. mold height [mm] min 250 Maximum opening width [mm] 850 Injection unit Screw diameter [mm] 50 Injection volume [cm3] 398 Shot weight [g] 359 Injection pressure [bar] 1550 Electro-hydraulic equipment Power rating of the pump motor [kW] 33,3 Power rating of barrel heating [kW] 15,7 Dimensions and weight (approximately) Net weight with control cabinet [t] 5,6 Dimensions (L x W x H) [m] 4,9 x 1,5 x 2,0

Key data: 4200 kN

Demag Ergotech Concept 420/810-2300 with the Sepro Success 33 robot Year of construction: 2006 Injection unit: Screw diameter: 60 mm Spray weight: 800 g Injection pressure: 2420 bar Dosing volume: 891 ccm Clamping unit: Clamping force: 420 t Tie bar spacing: 800x710 mm Size of clamping plates: 1200x1100 mm Ejector: hydraulic Clamping unit: toggle lever Control: NC 4 Additional equipment: Machine in very good technical condition Euromap 67 Robot Interface Air Valve x 4 Hydraulic, needle core pull, controlled by a proportional valve - from the side of the movable plate x 2 Hydraulic, needle core pull, controlled by a proportional valve - from the side of the fixed plate x 2 Hot runner control x 18 Injection unit hardened - Bimetal Central lubrication Parallel Movements Built-in print quality control system from Sensor Kistler - tool pressure measurement  ...

Molding machine of Mag Type: Ergotech, 150/500-840 concept control: NC 4 year of construction: 2001 Clamping unit Clamping force t Gap 150 mm: 500 Holm dimension mm: 500 x 500 min/max height mm: 275 / 585 Plate size: 1085 x 1185 injection unit Screw diameter mm: 50 Injection weight gr: 402 Injection volume cm m³: 442 Spray pressure bar: 1946 Dimensions and weights Dimensions Lxwxh m: 5.2 x 1.6 x 2.1 machine weight kg: 7,800

Key data: 800 , 149 , 35

Manufacturer: Demag Type: 80/420 - 310 concept Built: 2005 Control: NC 4 Control Type of closure: Hydraulish Closing force: 800 kN Tie bar ratio: 420 mm x 420 mm Plate size: 580 mm x 590 mm WZ Installation height: 250 mm Opening distance: 500 mm Plate spacing max: 750 mm Screw: 35 mm Lifting volume: 149 gram PS / 168.3 cc Spray pressure: 2020 bar General Engine: 18.5 kW Heater: 8.8 kW Dimensions: 3.9 m x 1.4 m x 1.9 m Weight: 4100 kg Screen text: German Optional extras Core train: x1

Key data: 1000 , 205 , 40

Manufacturer: Demag Type: 100/420 - 430 concept Built: 2004 Control: NC 4 Control Type of closure: Hydraulish Closing force: 1000 kN Tie bar ratio: 420 mm x 420 mm Plate size: 590 mm x 600 mm WZ Installation height: 250 mm Opening distance: 500 mm Plate spacing max: 750 mm Screw: 40 mm Lifting volume: 231 cc / 205 gram PS Spray pressure: 2020 bar General Engine: 18.5 kW Heater: 11.1 kW Dimensions: 4.9 m x 1.6 m x 2.1 m Weight: 4800 kg Screen text: German Optional extras Core train: x1 Air valve: x1 Robot interface

Key data: 1500 , 210 , 40

Manufacturer: Demag Type: 150/475 - 440 concept Year of construction: 1999 Control: NC 4 Control Locking type: Knee lever Closing force: 1500 kN Tie bar spacing: 475 mm x 450 mm Plate size: 690 mm x 660 mm WZ Installation height: min 230 max 460 mm Opening distance: 450 mm Plate spacing max: 910 mm Screw: 40 mm Lifting volume: 231 ccm / 210 gram PS Injection pressure: 1855 bar general Engine: 22 kW Heater: 11.7 kW Dimensions: 4.9 m x 1.6 m x 2.1 m Weight: 6600 kg Screen text: German Optional extras Core train: x1 central lubrication Air valve Robot interface

Key data: 350 , 78 , 30

Manufacturer: Demag Type: Ergotech 35/320 - 120 concept Year of construction: 2005 Control: NC 4 Control Closing type: Hydraulic Closing force: 350 kN Tie bar spacing: 320 mm x 320 mm Plate size: 460 mm x 450 mm Tool height: min 180 mm Opening distance: 350 mm Plate spacing max.: 530 mm Screw: 30 mm Lifting volume: 88.3 cc / 78 gram PS Injection pressure: 1393 bar general Engine: 11 kW Heating: 8.3 kW Dimensions: 3.4 m x 1.2 m x 1.8 m Weight: 2750 kg Screen text: German Additional equipment Robot interface Core train: x1 Air valve: x1 Temperature control point for hot duct

This SUMITOMO SHI DEMAG Ergotech 350 Concept Injection moulding machine was manufactured in the year 2003 in Germany. The machine has a clamping force of 3500 kN and a screw diameter of 60 mm.

This SUMITOMO SHI DEMAG Ergotech 350 Concept Injection moulding machine was manufactured in the year 2003 in Germany. The machine has a clamping force of 3500 kN and a screw diameter of 60 mm.

Clamping force 250t, clear tie bar width: 560mm, operating pressure: 190bar, weight: 10.7t, with documentation, an inspection is possible.

Key data: 3500 , 60

warehouse no.: 503071 manufacturer: DEMAG type: Concept 350-710-1450 controller: NC4 year of construction: 2003 operation hours: 62370 h clamping force: 3500 kN distance between tie-bars h x v: 710 x 630 mm size of mould plates h x v: 1040 x 950 mm min. mould height: 330 mm max. mould height: 830 mm max. open daylight: 1385 mm opening stroke: 675 mm screw diameter: 60 mm swept volume: 763 ccm injection pressure: 1905 bar equipment included: 16x control for hotrunner screen text german CEE-socket 16A core pulling hydraulically 1x air valve moveable WAP machine incl. water flow regulator machine without material hopper Anti vibration mounts electric interface for handling units according to Euromap 12 interface EUROMAP 63 Schuko-socket 10A measures of machine l x w x h: 6.5m x 2m x 2.3m total weight: 15300KG

Control type: NC 4 Number of hours: 38,000 hours Closing force: 420 T Opening stroke: 710 mm Between columns: 800 x 710 mm Tray dimensions: 1200 x 1100 mm Mini/maxi mold: 380/820 mm Max distance between trays: 1530 mm Injection: Screw diameter: 60 mm Screw length: 20D cm3: 763 Bars: 1905 General: Motor power: 45 kW Heating power: 23.1 kW Closing weight: 18t Injection weight: Length dimensions: 8 m Width dimensions: 2.20m Height dimensions: 2.50 m Options: Cores: 2 Robot interface: YES Bi metal: YES

INJECTION UNIT Screw diameter: 60 mm Calculated injection volume: 763 cm³ Length / diameter ratio: L / D Pressure on the material: 1905 bars CLOSING UNIT Closing force: 2500 kN Mold thickness Mini / Max: 370-710 mm Passage between columns: 630 x 630 mm EQUIPMENT 4 Cores EUROMAP robot socket

Demag Concept 300-630/2300 injection molding machine Year of production - 2006 Clamping force - 3000 kN Spacing between columns - 950 X 950 mm Table size - 630 x 630 mm screw diameter - 80 mm injection volume 1583 cc injection weight - 1430 g injection pressure - 1437 bar machine weight - 14,600 kg dimensions of the machine 6.5 x 1.9 x x 2.3 m number of man-hours worked 75299 Screw 80 mm hardened (good condition) RSP revised in 2022 2021 injection system has been completely sealed 2019 the pump along with the control valve and Hall sensor has been completely revised

Demag concept 420/810-2300 year 06 We offer a Demag injection molding machine in working condition. Used only in morning shifts and in semi-automatic mode. Must be seen in operation at our injection plant

Key data: 100000 kN, 149 g/PS, 35 mm

Clamping force: 100 t Year of construction: 2001 Injection weight in PS: 149 g Control Type: NC4 Injection unit: .../310 Screw diameter: 35 mm Spec. Injection pressure: 2020 bar Spray volume: 168.3 cc Injection weight in PS: 149 g Hydr. Drive power: 18.5 kW Cylinder heating capacity: 9.4 kW L/D screw ratio: 20 Clamping unit: 100/... Clamping force:: 100 t Size of clamping plates: 600 x 600 mm Lights spar spacing: 420 x 420 mm Ejector force: 41.2 kN Tool installation height: 250 mm Aperture travel: 500 mm Max. plate spacing: 750 mm Ejector travel: 150 mm General information: Fuel tank capacity OIL: 220 l Weight: 4800 kg Dimensions(m) LxWxH: 4.3 x 1.4 x 2.0 m Equipment: 1 x Hydraulic Core 1 x Pneumatic Valve

Inv. Num. : 7418 Type: Concept 420/810-2300 Producer: Demag Created: 2006 Parameters: Clamping force: 420 t Screw diameter: 60 mm Injection capacity: 891 cm³ Injection mass: 800 g Height of the clamping plate: 1200 mm Width of clamping plate: 1100 mm Distance between uprights (horizontal): 800 mm Distance between uprights (vertical): 710 mm Maximum spraying pressure: 2420 bar Machine length: 7900 mm Machine width: 2200 mm Machine height: 2500 mm Injection weight: 20000 kg

Clamping force: 35 t Year of construction: 2006 Injection weight in PS: 30 g Control Type: NC4 Injection unit: .../80 Screw diameter: 22 mm Spec. Injection pressure: 2061 bar Spray volume: 34.2 cc Injection weight in PS: 30 g Hydr. Drive power: 7.5 kW Cylinder heating capacity: 5.1 kW Clamping unit: 350/... Clamping force:: 35 t Size of clamping plates: 460 x 450 mm Lights spar spacing: 280 x 280 mm Aperture travel: 350 mm Max. plate spacing: 530 mm Ejector travel: 100 mm General information: Delivery Time: Natychmiast Weight: 2750 kg Dimensions(m) LxWxH: 3.2 x 1.2 x 2.0 m Equipment Filling funnel Sorting flap bimetallic plasticizing structure hydraulic core on movable plate

This DEMAG Concept 420/810-2300 Injection moulding machine was manufactured in the year 2006 in Germany. It is equipped with a Ergo control unit. The machine has a screw diameter of 60 mm, a stroke volume of 891 cm³, a injection pressure of 2420 bar, a shot weight of 800 g/PS and clamping force of 4200 kN. The distance between bars are 800x710 mm and the size of mould platens 1200x1100 mm.

This injection moulding machine, manufactured in 2000 by DEMAG, model Ergo-Tech 350 Concept, comes with handling technical specifications, making it a prime choice for efficient and reliable production. Its design emphasizes durability and ease of use, suitable for a wide range of injection moulding applications. The DEMAG Ergo-Tech 350 Concept machine we have for sale represents an opportunity to enhance your manufacturing capabilities with a proven, quality piece of equipment. For further information, please contact us.

The machine has a Demag DR631-0399 robot built into it. Machine with CE standards. Type of material used: PC/ABS Service History: 3.2018 - Calibration - Ergocheck 1.2016 — Replacement of a faulty hydraulic system pressure sensor. scheme 1.2015 – repair of the nozzle rod. units 2.2014 — Replacement of the chamber, auger and tip 1.2013 — Replacement of the screw and tip 6.2012 – Repair, re-sealing of the injection cylinder. units 11.2010 — Repair of proportional valve 4.2008 — Replacing the control panel display 3.2008 — Replacing the proportional valve 3.2008 — Calibration — Ergocheck 12.2007 — Replacing the tip

Demag hose pouring machine type: Ergotech 500-200 systems control: NC 4 construction year: In 1999 Schliesseinheit Schliesskraft t: 50 opening ways mm: 400 cross-beam measure mm: 355 installation heights min / max. mm: 210 record size: 520 x 520 hose unity snail diameter mm: 30 hose weights gr: 94 hose volumes cm?: 106 hose pressure cash: In 1995 mass and weights dimensions LxBxH m: 3.6 x 1.4 x 1.8 machine weight kg: 2900 other 1 x nuclear trains

Demag hose pouring machine type: Ergotech per 80-400 controls: NC 4 construction year: In 1998 Schliesseinheit Schliesskraft t: 80 cross-beam measures mm: 400 installation height min / max. mm: 250 record sizes: 580 x 580 hose unity snail diameter mm: 40 hose weights gr: 205 hose volumes cm?: 217 mass and weights dimensions LxBxH m: 4.13 x 1.13 x 1.81 machine weights kg: 3800 other 1x nuclear train, new cylinder with snail

Demag hose pouring machine type: Ergotech 330-840 systems control: NC 4 construction year: In 1998 Schliesseinheit Schliesskraft t: 330 cross-beam measures mm: 815 x 735 installation height min / max. mm: 330830 record sizes: 1040 x 950 hose unity snail diameter mm: 60 hose weights gr: 560 hose volumes cm?: 636 hose pressure cash: 1351 mass and weights dimensions LxBxH m: 6.5 x 1.9 x 2.2 machine weights kg: 14500

Molding machine of Mag Type: Ergotech 100-430, El Exis control: NC 4 year of construction: 2000 Clamping unit Clamping force t 100 Gap mm: 445 Holm dimension mm: min/max height of 420 x 420 mm: 460 / 560 Plate size: 690 x 660 injection unit Screw diameter mm: Gr 40 injection weight: 210 Injection volume cm m³: 231 Spray pressure bar: 1855 Dimensions and weights Dimensions Lxwxh m: 5 x 1.6 x 2 machine weight kg: 6900 Miscellaneous 1 Core pull of armored snail