We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
used
Charmilles Robofil 310 CNC type Year: 1994 X axis Axis shift of 400 mm Axis Y axis shift 250 mm Z-axis travel 400 mm The stroke of the U axis is 400 mm The stroke of the V-axis 250 mm We attach 8 cartons of brass wire 0.25 and all the instructions including one in Polish
used
Charmilles Robofil 4020 Year 1996 Travel: X-450, Y-320, Z-270, U-100, V-100 Max cutting angle: 30 degrees Max workpiece weight: 500 kg Programmable axes: X, Y, Z, U, V Max dimensions of the detal - 990 x 505 x 270
used
Charmilles Robofil 440 SL EDM Wire Cutting Machine X : 550 mm Y : 350 mm Z : 400 mm
used
Wire EDM CHARMILLES TECHNOLOGIES ROBOFIL 300 (1995) In production. X axis (longitudinal): 400 mm Y axis (transverse): 250 mm Z axis (vertical): 400mm Max piece length: 850 mm Max piece width: 500 mm Max piece weight: 500 kg Working tank length: 900mm Working tank width: 800mm Working tank height: 400mm Max piece height: 400 mm Length x width x height: 1800 × 1600 × 2230 mm. Weight: 2500kg
used
This CHARMILLES Robofil 2020 SI Erosion Machine was made in 1996 in Switzerland. It has been working for approximately 73000 hours. It operates in solid conditions without any problems and can be inspected under production. In the delivery scope all standard accessories are available (except clamping devices). For more information see PDF attached.
used
Machining paths X/Y/Z: 350mm/220mm/220mm, table dimensions X/Y: 680mm/450mm. max. workpiece weight: 750kg, max. workpiece dimensions X/Y/Z: 1000mm/550mm/250mm. Wire diameter range: 0.1mm-0.3mm, wire spool size: 8kg, skewing capacity: 0°-30°. Dimensions X/Y/Z: 2020mm/2050mm/2000mm, weight: approx. 2500kg, operating hours: approx. 60000.
used
Max. workpiece weight: 800kg, weight: 3.34t, with generator, the PC of the machine is defective, an on-site inspection is possible.
used
Axis X ... 350mm Axis Y ... 220mm Axis Z ... 220mm Machine weight ... 2100kg Max. workpiece weight ... 750kg Max. workpiece length ... 1000mm Max. workpiece height ... 220mm Max. workpiece width ... 550mm The machine is in good condition, possible to test under electricity.
used
The machine has been standing still for a couple of years now, so it needs a complete overhaul, it is not possible to see it in operation. - tank dimensions: 1105 x 765 x 435 [mm] - maxi dimensions of the pieces: 1100 x 760 x 360 [mm] - maxi piece weight: 800 [kg] - strokes: X x Y x Z: 450 x 320 x 162 [mm] - U strokes: +/- 50 [mm] - V strokes: +/- 50 [mm] - solution: 1 [µm] - wire unwinding speed: 2 - 15 [m / min] - rake angle: +/- 30 ° - tank dimensions: 1150 x 900 x 2280 [mm] - tank capacity: 1000 [l] - dimensions: 3700 x 2700 x 2300 - weight: 4930 [kg]
used
Key data: 450 mm, 320 mm, 162 mm
Control FJ.37X Travel X/Y/Z 450/320/162 mm Travel U/V +/- 50 mm Workpiece size X/Y/Z 1100/760/360 mm Table load 500 kg Weight 3200 kg Wire guides ø0.25 and ø0.30 Base strips for EROWA tension beams Wire Alignment Block Wire threading module
used
Fanuc CNC model Automatic threading yes Immersion EDM type Maximum wire inclination +/- 30° 400mm X Axis Travel 400 mm Y Axis travel 300 mm Z Axis travel 400 mm U Axis travel 500 mm V Axis travel 400 mm Maximum piece dimensions 900 x 600 x 400 mm Max piece weight 1000 kg
used
X-travel: 800mm, y-travel: 600mm, z-travel: 400mm, U-travel: 60mm, V-travel: 60mm, workpiece dimensions: 1300x910x400mm, max. workpiece weight: 2.3t, dielectric capacity: 210l, connected load: 10kVA, length: 2550mm, width: 2350mm, height: 2200mm, weight: 4.84t, with generator, wire guide, protective cabin, documentation and other accessories, on-site inspection is possible.
used
Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm Ampere: 0 A CNC Brand: 0 CNC Model: 0 Operating hours: 12000 Technical data Working table: Length: 680 mm Width: 450 mm Max. dimensions of work piece: Length: 1000 mm Width: 550 mm Height: 220 mm Table load max.: 750 kg Longitudinal traverse (X-axis): 350 mm Cross traverse (Y-axis): 220 mm Vertical travel (Z axis): 220 mm Taper-cut +/-: 30 ° Diameter of electrode wire: from: 0.33 mm up to: 0.10 mm Max. cutting speed with wire 0.33 mm: 400 mm2/min Total power required: 10 kVA Dielectric aggregate: Contents: 760 l Air connect: 6 - 7 bar Voltage 50 Hz 3x: 400 Volt Total power required: 12 kVA Weight total installation approx.: 2100 kg Overall dimensions machine: Length: 2050 mm Width: 2020 mm Height: 2000 mm Various accessories: Cooling unit for fluttines
used
Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm Ampere: 0 A Positions ATC: 0 Tank contents: 0 CNC Brand: 0 CNC Model: 0 Control: CHARMILLES Technical data Table length: 800 mm Table width: 560 mm Table load max.: 800 kg Longitudinal traverse (X-axis): 450 mm Cross traverse (Y-axis): 320 mm Max. distance from the table and sleeve: 640 mm Working vessel:length inside: 1195 mm Width: 800 mm Height: 410 mm Working head: way rapid feed (Z): 410 mm Dielectric aggregate: Contents: 560 l Height: 870 mm Width: 2110 mm depth: 750 mm net weight: 300 kp Generator: Power: 128 A Height: 2100 mm Width: 650 mm depth: 600 mm Total power required: 7.0 kVA Operating voltage: 380 Volt Machine´s weight about: 320 kg Machine´s weight about: 4100 kg Overall dimensions machine: Length: 3700 mm Width: 2110 mm Height: 2700 mm
used
Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm Ampere: 0 A Positions ATC: 0 Tank contents: 0 CNC Brand: 0 CNC Model: 0 Control: CHARMILLES Technical data Table length: 750 mm Table width: 600 mm Dimension of the workpice: Length: 1200 mm Width: 850 mm Height: 400 mm Table load max.: 1600 kg Longitudinal traverse (X-axis): 600 mm Cross traverse (Y-axis): 400 mm Height adjustment (Z-axis): 450 mm max. electrode weight: 100 kg Voltage 50 Hz 3x: 400 Volt Machine´s weight about: 4500 kg Overall dimensions machine: Length: 3150 mm Width: 2750 mm Height: 2960 mm
used
AGIETRON HYPERSPARK 2 HS Sinker 2008 Design with lowerable working container Work table with 50 mm hole grid travel X/Y/Z 350x250x350 mm -Workpiece size: LxWxH=650x580x250 mm or 820x420x250 mm Integrated C axis, for rotation, indexing and erosion Electronic laser measurement of all axes Detection of the electrode and workpiece position 1 set of documentation (CD + manuals) AGIEVISION 5 Control with multitasking DNC interface with transmission protocolXon/Xoff and LSV2 2 serial interfaces RS 232C for DNC and master computer LAN connection for data exchange via in-house network RJ45 3 drives: hard drive, 3 1/2" floppy disks, CD-ROM Without tool changer
used
Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm Ampere: 0 A CNC Brand: 0 CNC Model: 0 Control: CHARMILLES Operating hours: 171812 Technical data Working table: Length: 950 mm Width: 620 mm Max. dimensions of work piece: Length: 1260 mm Width: 690 mm Height: 360 mm Table load max.: 800 kg Longitudinal traverse (X-axis): 630 mm Cross traverse (Y-axis): 400 mm Vertical travel (Z axis): 160 mm U/V axis travel: +/-48 mm Resolution: 0.05 µm Taper-cut +/-: 30 ° Diameter of electrode wire: from: 0.05 mm up to: 0.33 mm Dielectric aggregate: Contents: 240 l Voltage 50 Hz 3x: 400 Volt Total power required: 15 kVA Machine´s weight about: 4100 kg Overall dimensions machine: Length: 2660 mm Width: 2610 mm Height: 2370 mm Various accessories: CNC control Automatic wire treading
used
Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm Ampere: 0 A Positions ATC: 0 Tank contents: 0 CNC Brand: 0 CNC Model: 0 Control: CHARMILLES Technical data Table length: 500 mm Table width: 400 mm Table load max.: 500 kg Longitudinal traverse (X-axis): 350 mm Cross traverse (Y-axis): 250 mm Max. distance from the table and sleeve: 150/450 mm Working vessel:length inside: 800 mm Width: 550 mm Height: 370 mm Working head: way rapid feed (Z): 300 mm max. electrode weight: 50 kg Dielectric aggregate: Contents: 410 l Generator: Power: 64 A Total power required: 7.5 kVA Voltage 50 Hz 3x: 380 Volt Machine´s weight about: 2500 kg Overall dimensions machine: Length: 1900 mm Width: 1690 mm Height: 2800 mm
used
Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm Ampere: 0 A Positions ATC: 0 Tank contents: 0 CNC Brand: 0 CNC Model: 0 Technical data Table length: 500 mm Table width: 400 mm Number of spline: 3 T-channel width: 12 mm Distance of the T-slots: 125 mm Table load max.: 500 kg Longitudinal traverse (X-axis): 350 mm Cross traverse (Y-axis): 250 mm Height adjustment (Z-axis): 300 mm Working vessel:length inside: 800 mm Width: 550 mm Height: 370 mm Dielectric aggregate: Contents: 450 l Total power required: 5 kVA Voltage 50 Hz 3x: 400 Volt Machine´s weight about: 2500 kg Overall dimensions machine: Length: 3300 mm Width: 2400 mm Height: 2480 mm Various accessories: Loading roboter: Type: QCRi Pallet positions: 8 Holder: 54 Fire extinguishing system (without bottle) Interface serial port RS 232 Lamp
used
Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm Ampere: 0 A CNC Brand: 0 CNC Model: 0 Technical data Max. dimensions of work piece: Length: 900 mm Width: 520 mm Height: 270 mm Table load max.: 500 kg Longitudinal traverse (X-axis): 320 mm Cross traverse (Y-axis): 220 mm Vertical travel (Z axis): 270 mm Taper-cut +/-: 30 ° Diameter of electrode wire: from: 0.25 mm up to: 0.30 mm Overall dimensions machine: Length: 3400 mm Width: 2400 mm Height: 2300 mm
used
Machine is in good condition X : 350 mm Y : 250 mm Z : 350 mm
used
Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm Ampere: 0 A CNC Brand: 0 CNC Model: 0 Technical data Working table: Length: 900 mm Width: 600 mm Max. dimensions of work piece: Length: 1200 mm Width: 700 mm Height: 400 mm Table load max.: 1500 kg Longitudinal traverse (X-axis): 550 mm Cross traverse (Y-axis): 350 mm Vertical travel (Z axis): 400 mm Taper-cut +/-: 30 /400mm ° Diameter of electrode wire: from: 0.33 mm up to: 0.10 mm Dielectric aggregate: Contents: 1200 l Air connect: 6 - 7 bar Voltage 50 Hz 3x: 400 Volt Total power required: 10 kVA Weight total installation approx.: 2850 kg Overall dimensions machine: Length: 2810 mm Width: 2600 mm Height: 2080 mm Various accessories: Cooling unit for fluttines: HITEMA
used
Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm Ampere: 0 A CNC Brand: 0 CNC Model: 0 Control: CHARMILLES Technical data Working table: Length: 560 mm Width: 440 mm Max. dimensions of work piece: Length: 1130 mm Width: 510 mm Height: 260 mm Table load max.: 500 kg Longitudinal traverse (X-axis): 318 mm Cross traverse (Y-axis): 218 mm Vertical travel (Z axis): 114 mm U axis: +/-48 mm V-axis: +/-48 mm U/V axis travel: 48 mm Taper-cut +/-: 30/65mm ° Diameter of electrode wire: from: 0.1 mm up to: 0.25 mm Forward feed for wire elctrode: from: 0.2 m/min up to: 15 m/min Max. coil weigth: 16 kg Dielectric aggregate: Empty weight: 4400 kg Contents: 240 l Generator: Cut capacity max. from: 300 mm2/min Voltage 50 Hz 3x: 380 Volt Total power required: 12 kVA Weight total installation approx.: 4500 kg Overall dimensions machine: Length: 3700 mm Width: 2600 mm Height: 2300 mm Variou ...
used
BRAND: CHARMILLES YEAR: 1998 MODEL: ROBOFORM 810 APPLICATION TYPE: EDM LOCATION: PORTUGAL MACHINE TYPE: EROSION MACHINE AVAILABILITY: IMMEDIATELY CONTROL UNIT BRAND: CHARMILLES GINDUMAC ID: PT-EDM-CHA-1998-00001 Technical Information GENERAL DATA MEASUREMENTS WIDTH: 3950 MM MEASUREMENTS DEPTH: 3550 MM MEASUREMENTS HEIGHT: 2960 MM MACHINE WEIGHT: 5300 KG CONTROL UNIT BRAND: CHARMILLES MAIN DRIVE NUMBER OF AXIS: 4 MOVEMENT X-AXIS MOVEMENT: 800 MM Y-AXIS MOVEMENT: 600 MM Z-AXIS MOVEMENT: 500 MM Additional Information MACHINE BENEFITS TECHNICAL MACHINE BENEFITS: - MAX. PART DIMENSION: 1500 X 1000 X 500 MM - MAX. WEIGHT PART: 4200 KG - DIELECTRIC VOLUME: 1600 L - C-AXIS: YES - TOOL CHANGER: 24 - CHUCK: 3 R QUALITATIVE MACHINE BENEFITS: - MACHINE IN EXCELLENT CONDITION - REFURBISHED
used
Longitudinal X: 0 mm Cross Y: 0 mm Vertical Z: 0 mm Ampere: 0 A MACH-id 4003 MAKE Charmilles TYPE ROBOFORM 200 YEAR 1990 DIMENSIONS Length 3000 mm Width 1600 mm Height 2500 mm