7 TROESTER Rubber extruders used machines

Troester.200mm H/F strainer M/C Number 7175-71 L/D 6.5/1 Roller Feed 350mm. Hinged strainer head with hydraulic clamp. 125KW AC v/s motor. On single bedplate. With controls.

available Troester Triplex Extruder Top machine QSM 90x 16D Middle machine 200W x 6D Below machine QSM 150 x 16D Head MW500 Description attached!

90s cold feed extruder, GE 90 x 16 D Vac, make Troester, with large hose / profile spray head, drive 52 KW Siemens AC, 4 TCU Siengle

cold feed extruder - 60 mm x 18 D vacuum, with feed roller, drive 22 KW, screw speed 10 to 60 rpm, with gear pump, 5 TCU,

cold feed vacuum extruder Troester 90 mm x 18 D, with feed roller, drive 46 kW, pie speed 10 to 60 rpm, 5 TCU,

Manufacturer: Paul Troester Maschinenfabrik/Hannover Year of construction: 1978, machine was in operation until the end of 2015 Screw diameter: 150 mm Length: 16 D (approx. 2,400 mm) Screw speed: 2.5-25 / 4 - 40 U/Min. Centre height of the extruder: 1,100 mm Type of gearbox 3 TH 990 K / 2s, 2 speeds. Gear ratio: = i1 16.5: 1 i2 = 26.4: 1 Maximum gearbox output torque: 45,000 nm Maximum permissible injection pressure: 350 bar without limitation through the extrusion head. The extruder will be overhauled and designed/changed according to customer's specification. Below pictures 1-4 show an extruder overhauled by us.

Used rubber extruder make Troester, type GSV 60/k-12-18D-m.S., Execution as desired, with or without vacuum Built in 1991, machine was in operation until the beginning of 2010 Feed roller Kpl. new drive with flat gear motor Screw speed max. 62 rpm. Engine power 22 kW Control with PLC and temperature control new on request Extruder similar to attached photos.

Used Troester rubber extruder type GSV 60/k-12-18 D with feed roll can be modified/overhauled according to customer\s specification, with or without vacuum, year of construction: 1991 machine was in operation until end of 2010. including feed roll, new drive with flat-gear motor screw speed: maximum 62 rpm motor power: 22 kW PLC control and TCU can be renewed, if requested.

roll surface width: 450 mm roll diam. toproll: 203 mm roll diam. bottom roll: 203 mm output: 8,8 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

screw ø:: für Extruder 90 mm screw length:: -- screw speedl:: -- U/min drive power:: 13,6 kW Condition: little used, as good as new Specification: gear pump ZP 75/50 for extruder size 90 - SEW helical gear units: R 97 - Siemens direct current motor: 1 GG5 118 - Drive power: 13.6 kW, 57 A - curved tooth coupling - With clamp for the head connection, - Clamping flange for extruder and head connection, - Base plate with linear guide rails, - Tooth shaft diameter: 75 mm - tooth width: 50 mm - helical gearing, hardened steel bearings, right-hand drive - without control The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

A Troester mixing mill is available. Including strip cooler, year of manufacture: 1993. An on-site inspection is possible.

screw ø:: 90 mm screw length:: 16D screw speedl:: ca. 40 U/min drive power:: 48,5 kW Condition: used, overhauled to order, including warranty, including CE marking Specification: extruder – used with feed roller - Screw diameter: 90 mm - Screw length: L = 12D - Screw speed approx.: 40 rpm - Motor rated power: 48.5 kW - Belt drive, number of belts: 5 - Number of heating/cooling zones: 4 - Voltage: 3x 380V, 50Hz, N For further details, please refer to the attachment. Price on request, depending on design and customer requirements The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

1 x Berstorff GmbH 250mm strainer extruder, Year of manufacture: 1988, L/D ratio 7:1, power roller feed (300mm wide), with 120kW, 1800rpm DC variable speed motor mounted on top of gearbox (belt drive), with tube head and knife at top for sheet extrusion. Complete with control panel etc and in very good condition.

Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel

Key data: 70

Single-screw rubber extruder with feed roller and degassing in screws of 70mm and a process length of 22.D - with two-speed temperature-controlled entagling screw - Degassing cylinder with device for static and/or vacuum degassing of the material - a vacuum block pump - two water temperature control units with 9kW heating capacity each, - a Siemens SPS S7 machine with Siemens KTP1200 HMI control panel - a directly driven feed roller feeder for rubber raw strips, a funnel-material stiffening system with Strip monitoring - temperable base body for tool holder and v.m

Farrel Twin Screw / Rollerdie Extruder complete available with Motor and Inverter Description attached!

Francis Shaw 30mm Extruder Roller Feed LD ratio 15:1 Year 1993

Berstorff 6inch (150mm) Strainer Extruder Manufactured by: Krauss Maffei Berstorff Model: GE 150 K Screw Diameter: 6"/150 mm L/D Ratio: 6 Speed: Variable, up to 45 rpm Motor: 90 KW, 1500 RPM Transmission: Direct Drive, 3 steps reduction Gear Reduction Ratio: 33:1 Year 2009

Iddon 75mm Cold Feed Rubber Extruder With roller feed With motor, gearbox and control panel

120 mm cold feed pen convert-extruder, GE 120 SC, make Berstorff, output capacity up to 1,000 kg /h as a power extruder with strip spray head, complete rebuild mechanically and electrically in 2024

Key data: 50 mm

50mm Extruder Manufacturer: Rutil Screw diam. 50mm LD ratio 15:1 Max speed (50 Hz) 70rpm

AST 220 / POMINI-FARREL flat head / POMINI-FARREL 18"x15" Slabber / BANDERA Slabber. Refer to code 1043-1044-1045-1046 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Key data: 215 mm, 304

Pomini 12” x 8.5” Dump Extruder Type 12/8.5 Year of Manufacturing: 1993 Conical screw 300mm 215mm diam. Pneumatic crammer feed with DC variable speed motor Pelletizing head Without controls

Colmec 150mm Extruder Model: TGF 150/ 16D LD ratio 16:1 Screw length 2340mm Siemens Motor, 178kW, 1860rpm Hydraulically operated crosshead With Control cabinet With Temperature control unit Spare screw Year 2001

Sale of spare parts of EEK 125.22 V, including vacuum cylinder, screw and V-pump, 6 x TCU, Power cabinet with FU 165 KW