133,336 used machines on RESALE, but how to find them? Machine Search
Set of blow molds for PET blowing machine Sidel SBO Universal - 10 molds HR for heat resistent bottle 1.0 litre - 10 molds for standard bottle1.0 litre Molds were used to produce PET bottles for juices Low working hours Molds are n very good condition Available immediately Can be customised
max. format 54 x 72 cm Built in 1960 Inking unit not complete for punching / embossing Price on request. We supply and install worldwide.
Grinding wheel dimensions (od x id x width): 508 x 304.8 x 160 mm, Ø min/max to be rectified: 1.5 / 75 mm, Regulating wheel width: 160 mm, Regulating wheel dimensions (od x id x width): 304.8 x 190.5 x 160 mm, Grinding wheel width: 160 mm, Maximum length to be rectified in plongeé: 160 mm, Grinding wheel head motor power: 11 Kw, Long: 2.015 mm, Width: 1.280 mm, Tall: 1.440 mm, Weight: 3,000 Kg approx.
CLAMPING FORCE: 150TON PLATEN SIZES: 1295 X 990 DBTB: ROTARY TABLE 1520 MIN MOULD HEIGHT: 300 MOULD OPENING STROKE: 400MM MAX DAYLIGHT: 700MM SCREW DIAMETER: 40MM INJECTION PRESSURE: 2678BAR STROKE VOLUME: 283CM3 SHOT WEIGHT (P/S): 257GR CONTROLS: UNILOG B6 MOTOR: 22KW HEATING CAPACITY: 12.1KW SCREW DRIVE: HYDRAULIC CORE PULLING: 4 AIR VALVES: 1 HOT RUNNER: 8 ZONE INTERGRATED ADDITIONAL: HORIZONAL INJECTION VERTICAL CLAMP
Marel / Townsend Revoportioner Type: TRP630 Serial number: 10098176 Year of construction: 2012 Belt width: 630 mm Compressed air: 8 - 10 Bar, 200 Nm³/h Water: 2.5 - 3.5 Bar Power: 3 x 400V, 50Hz, 5kW Dimensions: 1850 x 1700 x 1700 mm Weight: 1000 kg Risco vacuum filler Type: RS505CP Serial number: C809047 Year of construction: 2010 Pump capacity: max 8000 kg/h Filling pressure: up to 40 Bar Hopper: 350 litres Power: 3 x 400V, 50Hz, 8kW Dimensions: 2100 x 1200 x 2250 mm Weight: 1010 kg With lifter for 200L tote bins
Process chiller / chiller air-cooled, Type: Aries TECH AST2 115 U MTA S.p.A. The Aries TECH AST2 115 HE are compact chillers suitable for outdoor installation (from -20°C to +48°C) with shell and tube evaporator, four scroll compressors, compressor shut-off valves, crank pan heater, phase monitoring, P3 double pump, tank 598 litres, electric antifreeze heater, condenser filter and control and control cabinet. Cooling capacity (kW): 315 Cold water temp. Exit/Entry (°C): 7 / 12 Volume flow (m³/h): 53.8 Available. Pump pressure (bar): 2.99 Ambient Temperature (°C): 32 Refrigeration circuit: Refrigerant R 410A Refrigeration Circuits (Quantity): 2 Compressors (quantity): 4 Power levels (%): 0-25-50-75-100 Electrical data: Voltage V 400, frequency Hz 50, phases Ph 3, Max. power consumption (kW): 158 Max. Current (A): 262 Starting Current Circuit (A): 507 P ...
Offer 25269 PVC – Gas Strip Sawing Machine Specifications: - Saw blade speed frequency-controlled for very fine sawing - Saw blade diameter 200 mm -Auto. Workflow - Press stop with SICO counter to adjust the glass contact pressure - -simulation - Pneumatic connection 6 bar - Drive 400 V / 0.8 kW - Space requirement approx. W 400 x H 1200 x D 700 mm - Weight approx. 80 kg - Machine stand
Offer 73066 Specifications: - Sanding belt dimensions approx. 2000 x 150 mm - Surface grinding opening approx. 560 x 150 mm - Sanding belt speed approx. 30 m/sec. - Contact washer B 150 / D 200 mm - Drive pulley B 150 / D 200 mm - Drive 400 V / 3 kW - Working height adjustable - separate mot. Dust extraction - Space requirement approx. W 750 x H 1050 x D 1500 mm - Space requirement para. approx. W 750 x H 1250 x D 750 mm - Weight approx. 180 kg
ENGEL ES 1350/350 HL injection moulding machine was built in 1995 in Austria by ENGEL AUSTRIA GmbH. The machine, which is designed for the economical production of plastic parts, is distinguished by the use of many components with excellent technical parameters. These parts are produced using the reliable injection moulding method, which involves feeding plasticised plastic into a mould and then clamping it with high press force. A precision mould clamping system, operating at a maximum force of 350 tonnes, guarantees high repeatability and quality of the manufactured parts. Once the production process is complete, the robot automatically transfers the finished products from the workspace to a conveyor belt. The ES 1350/350 HL injection moulding machine weighs 5000 kg. Technical specifications of the ENGEL ES 1350/350 HL injection moulding machine - CNC controller: ENGEL - maximum m ...
Key data: 600 kN, 132 g/PS, 35 mm
Arburg 320C-600-250 Injection Moulding Machine (241) Ability to work vertically Number: 241 Availability: in stock Year of production: 2008 Producer: Arburg Condition of Injection Molding Machine: Used Screw diameter [mm]: 35 Injection weight [g]: 132 Injection pressure [bar]: 1820 Clamping force [kN]: 600 Gap spacing [mm]: 320×320 Panel size [mm]: 446 x 446 Min. mould height [mm]: 200 Control Type: Selogica Tongue: German Installed power [kW]: 23.9 Working hours [h]: 74753 Weight [kg]: 2330 Dimensions [mm]: 3500×1500 Feed hopper: NO Robot Socket: Yes Core String: 1x
ROMACO NOACK BLISTER PACKING LINE --- 1) BLISTER PACKING MACHINE ROMACO NOACK, MODEL N921 Year of construction: 2010 Rotary sealing machine. With the latest servo technology, and the best tool-free changeover times in the industry. CHARACTERISTICS • Carton output: 400/min. (max) • Forming cycles: 100/min. (max) • Blister output: 500/min. (max) Compatible products: Tablets, capsules, soft gels, caplets, child-resistant/senior-friendly packs, coldform aluminum, multi-layer lidding materials • Foil width: 210 mm (max) • Forming depth: 12 mm (max) Reel diameter forming foil: 700 mm (max) • Reel diameter lidding foil: 280 mm (max) • Carton size (A/B/C): 120/95/210 mm (max) ---- 2) UHLMANN CARTONER, MODEL C150 Year of construction: 2010 Cartoner for big industrial production as well as in smaller, less equipped factories. with GMP-compatible pharm ...
Key data: 63 kp, 750 , 600
Rated power at 50%ED: 63kVA Short-circuit current: 26.3kA Electrode force: 65-390daN / single stroke Throat: 450-750mm --- Welding control: MPS 15036 (5 times, 1 program) --- Incl. additional options: - Footswitch with "de-energized" touchdown -Main switch --- Warranty 6 months --- Training + commissioning on request --- Spot welding electrodes + spare parts available from stock
Key data: 40 kp, 550 , 390
Rated power at 50%ED: 40kVA Short-circuit current: 26.2kA Electrode force: 65-390daN / single stroke Throat: 250-550mm --- Welding control: MPS 10 (5 times, 8 program) --- Incl. additional options: - Footswitch with "de-energized" touchdown -Main switch --- Warranty 6 months --- Training + commissioning on request --- Spot welding electrodes + spare parts available from stock
Key data: 25 kp, 150 , 120
Rated power at 50%ED: 25kVA Short-circuit current: 12kA Electrode force: 120daN / single stroke Projection: 150mm --- Welding Control: AR.01 (5 times, 2 program) --- Incl. additional options: -Foot switch -Main switch - Mounted on aluminium plate --- Warranty 6 months --- Training + commissioning on request --- Spot welding electrodes + spare parts available from stock
Spot welding gun --- Rated power at 50%ED: 22kVA Short circuit current: 17kA Electrode force: 360daN / single stroke Projection: 95mm --- - Electrode arm AE/2/96g + C34/2/63g --- Welding control: on request --- Spring balancer on request --- Warranty 6 months --- Training + commissioning on request --- Spot welding electrodes + spare parts available from stock
Chevalier FM 3VS X: 762 - Y: 305 - Z: 406 mm Max longitudinal travel X-axe: 762 mm Max cross-travel Y-axe: 305 mm Max travel Z-axe: 406 mm Max height workpiece: 70 > 476 mm Power on spindle: 3 HP Admission in boring head (ISO): ISO 30 Spindlespeeds: 3750 rpm Table size: 1220 x 230 mm Length: 1235 mm Depth : 1500 mm Height: 2100 mm Weight: 1 ton
Philips Diagnost TH/FS/VE with the following system components: - Generator Optimus 50 - Tube SRO 0951 0.3/1.0_Bj. 2014 - Tube tripod Diagnost FS - Vertical tripod Diagnost VE/VT Can also be used as a pure lung X-ray workstation. • Before taking over, all devices or systems have been tested on site for their functionality. • The system is located in our warehouse in Freiberg, Germany. It is packed on pallets, professionally lashed and wrapped in stretch film and can be picked up immediately • You buy the system in "IST" condition from the warehouse Freiberg (EXW), Saxony, Germany, and prepayment. • The sale is made as "Used", EXW Freiberg, Saxony, Germany, to resellers or dealers despite being fully functional without warranty. • The installation, commissioning and configuration of the system or plant components must be carried out by the manufacturer or by a sp ...
Width 78 cm Year of manufacture 2001 MC Control Round stack feeder Vacubelt 6 fold pockets in the parallel fold section Motorized fold pocket adjustment Downstream knife shaft Noise Insulation Hood Shed display Delivery date: immediately from stock Price on request. We supply and install worldwide.
height of profile: 60 mm : 60 weight of the machine ca.: 188 kg dimensions of the machine ca.: 0,85 x 0,45 x 1,25 m foot switch: - Fabr.-No.: 292539 - pneumatic clamping head The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offer 25290 Specifications: - Max. working width 3040 mm - max. material thickness at 40 kg / mm² strength 2 mm - Bending angle adjustment selectable 6 - 135 ° - Largest opening width / stroke of the upper beam 250 mm - Height adjustability - bending beam 50 mm - the lower beam 50 mm - Upper bolster drive 400 V / 0.37 kW - Bending beam drive 400 V / 0.75 kW - Manual backgauge - Split goat's foot bending splint - Space requirement approx. W 4000 x H 1400 x D 1200 mm - Weight approx. 3500 kg
Vacuum packer VAMA Specifications: Type: VB 300 Year of Make: 2020 230 Volt / 50 Hz /0.35 kW Weight: 40 kg Chamber size: 320 x 350 x 160 mm Sealing bar length: 310 mm Max. bag size: 300 x 350 mm Machine design Completely stainless steel Compact, solid design Surface ground Corrugated acrylic glass lid 2 inserts for different height levels in the chamber High-performance pump with 8 m³ capacity Easy operation with the new SC12 control system Vacuum adjustable Welding time adjustable Stock machine, immediately available! Function checked, condition see original pictures.
Fully automatic slicer / slicer GRAEF VA 800 / Art.Nr. VA804DE-C3 Specifications: 230 Volt / 50 Hz / 2.4 A / 500 W Knife diameter: 300 mm Stainless steel knife including underframe trestle Machine with CERA 3 coating Machine weight: 75 kg Year of Make: 2017 Knife speed 229 rpm Cutting thickness: 0.5 to 10 mm Stacking up to 4 stacking trays Longitudinal and transverse compartments, variable up to 4 rows, and round shelf Carriage designed for up to 40 cm of food to be cut Condition, see original pictures! If you have any questions, email or call.
GRAEF MASTER 3370 Specifications: 400 Volt / 50 Hz / 2.2 A / 450 W Cutting thickness adjustment: 0 to 24 mm Knife diameter: 330 mm Stainless steel knife, smooth Power current Machine with CERA 3 coating Weight: 43 kg Cutting size square: 300 x 224 mm Cutting size: Ø 190 mm External dimensions (L/W/H): 660 x 620 x 470 mm Installation area (L/W): 585 x 440 mm Carriage dimensions (L/W): 300 x 340 mm Knife speed: 229 rpm Noise level:
Inv. Num. : 5955 Type: Trumatic 500 R Producer: Trumpf Created: 2003 Parameters: Control system: TRUMAGRAPH CC 220 S Switch-on hours: 29433 h Compressive force: 22 t Machine height: 2200 mm Machine length: 6900 mm Machine width: 5800 mm Machine weight: 11000 kg 2020: Replacement of hydraulic hoses
Key data: 4020 mm, 1 mm
with material thickness adjustment, hydraulics on the left side of the machine, without roller shears, bending beam with removable attachment rail approx. 8mm, 3 stop fingers, control on the swivel arm, Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Working length: 4020 mm Sheet thickness max. steel: 1.5 mm Sheet thickness max. aluminium: 2.5 mm Sheet thickness max. VA: 0.8 mm Back gauge (max.): 1000 mm Projection: 1000 mm Colour: blue Total power requirement: 16 A Approx. space required: 6000 x 2000 x 1900 mm Weight approx.: 5000 kg Upper beam stroke (opening width): 200 mm without roller scissors Number of stands: 5 pieces Bending angle (max.): 145 degrees Machine Number: 0040-01
Undercarriage for edge banding machines Was mounted on Homag Edgeteq S-200, KDF 1130 FC (1100kg). But it certainly also fits on other machines, e.g. Brandt (might have to be adjusted a bit) Length of the U-profiles approx. 1130mm Body height incl. castors approx. 150mm 4 sturdy steel castors as swivel castors with grease fittings 2 Brakes 2 support plates for height compensation The machine can be demonstrated on site by appointment. We offer only machines that are ready for demonstration in our warehouse, see "other offers of this year". provider".
Duplo 645 in production ready condition. Counters: cut: 102 670 crease 355 946 paper: 419 128
This offer is aimed exclusively at entrepreneurs within the meaning of § 14 BGB. The price is net plus 19% VAT. Manufacturer: ARO Type: M 302 Year of Make: 1971 No. 1063655 380 V ~ 50/60 Hz E 100 100 All information is made to the best of our knowledge, errors excepted. The sale is subject to exclusion of any warranty. The exclusion does not apply to claims for damages arising from grossly negligent or intentional breach of the Seller's duties or to any injury to life, limb and health. Further legal Information can be found on the website of Witzenmann GmbH under the keywords "Imprint", "Terms and Conditions" and "Data Protection".
Width 66 cm Year of manufacture 2004 Pallet feeder PFH 66 Tremat Sheet Separation System Double Suction Wheel 4 fold pockets in the parallel fold section Automation Kit II Automatic folding pocket adjustment Automatic folding roller adjustment Downstream knife shaft 2 folding swords in the crossfold section 1 more fold pocket after the 1st cross break Shed display SAK without compressor New folding rollers and bearings in parallel fold Machine condition: cleaned and checked Price on request. We supply and install worldwide.
Width 56 cm Built in 1993 Round stack feeder Counting device PCS 100 1st station: 4 fold pockets 56 cm Downstream knife shaft 2nd station: 4 fold pockets 56 cm Downstream knife shaft Noise Insulation Hoods Shed Display SAK 56 without compressors / air supply Delivery date: immediately from stock Price on request. We supply and install worldwide.
Mobile semi-automatic wrap-around labeller with press-on belt and pre-installed for an Allen hot-air coder. Dispensing head: HERMA, type: 300 DHLK16. Max. label width: 150 mm.
Coordinate measuring machine Inv. Num. : 8632 Type: MICRO-MS 343 Producer: Tesa Created: 1997, GO 2020 Parameters: Machine dimensions: 800x750x1370 mm New Reflex system
Distance between points: 1000 mm, Height of points: 180 mm, Max. diameter to be rectified: 355 mm, Max. piece weight between points: 300 Kg, Max. weight with plate: 125 Kg, Transverse travel of the carriage (X axis): 350 mm, X-axis speed: 0.01 / 6.000 mm/min, X-axis Resolution: 0.0001 mm, X-axis measurement system: Digital ruler, Longitudinal travel of the carriage (Z axis): 1.300 mm, Z-axis speed: 0.01 / 15,000 mm/min, Z-axis resolution: 0.0001 mm, Z-axis measurement system: Digital ruler, Working wheel dimensions (od x id x width): Ø500 x Ø203 x 80 mm, Main engine power: 7,5 Kw, Angle of rotation of the grinding head: -30º / +210º, Workhead rotation speed: 10 / 800 rpm, Workpiece holder head cone: MORSE 5, tailstock cone: MORSE 4, Ø of the tailstock shank: 60 mm, Course of the counterpoint reed: 40 mm, Control type (CNC/manual): CNC, CNC brand: FAGOR, CNC model: 8040-T, Dimensions ...
HESTA HK 453 Year of manufacture 2002 - completely overhauled in 2021 Extruder 45 mm, 22 D Control Beckhoff New quill head, a new wall thickness control and new hybrid pump Denison The machine has been in operation for less than 50 hours since the overhaul in 2021, and in almost mint condition.
STIGAL DYNAMIC SPEED HQ plasma cutting machine was built in 2013 in Poland by STIGAL Marcin Stępień. The machine is used for precision cutting of sheet metal with a maximum thickness of 50 mm. The machining process is performed by a reliable plasma torch, which is powered by a CEBORA plasma source of the highest energy efficiency. Depending on the material type, high quality gas mixtures, i.e. oxygen, air, nitrogen and argon, are used in the cutting process. All this is complemented by an intuitive CNC control in which even the most advanced machining programmes are created in just a few steps. All this makes the offered STIGAL plasma cutting machine an excellent choice for both small businesses as well as large industrial plants. The total weight of the machine is approximately 2000 kg. Technical specifications of the STIGAL DYNAMIC SPEED HQ plasma cutting machine - operator panel ...
Key data: 100 t, 215 mm, 3100 mm
Ref.Nr. 00882 Name of the system: Used press brake Manufacturer: Beyeler Model PR4 1000 KN x 3100mm Year of construction 2000 Machine hours Not visible Power 100 tons Working range 3100mm DNC 80 control system Mains voltage 400V Connected load 5.5kW Machine weight 7000 kg Mains Frequency/Frequez 3~50Hz Max Pre-Fuse 20 AT Max Compressed Air 8Bar Max closing speed mm/s 200mm/s Pressing speed 1-10 Max stroke 215mm Max stop time 110mS Min safety distance 350mm Technical condition Fully functional
Electric roll Bending Machine 3 rolls Capacity: 800 mm x 3 mm Rolls diameter: Ø 105 mm Motor: 4 CV New electrical panel Front/back rotation Voltage: 220 V Tri (possibility of reversing the motor in 380 V) Equipped with: Emergency stop Equipped with: Protective cover Dimensions (L x W x H): 2000 x 1300 x 1300 mm Weight: approx 1,5 T
Klaaßen SDM15-5 turning machining centre, The top lathe we offer has the following in the basic configuration Technical parameters: ▪ SDM 4-5 CNC 4-Panel Bed Precision Lathe - Z-travel (slide longitudinal)= 5,000 mm (6,000 with TAE3) X-travel (face slide transverse)= 1,000 mm Y-axis (vertical movement)= 350 mm Maximum workpiece Ø = 1,500 mm Circulation diameter over face slide = 1,500 mm - Center width = 4,500 mm (5,500 with TAE3) ▪ CNC machine designed as a 4-lane tip lathe with full drive-over of the Bezels and superstructures - - - Cross slides and face slides restrict the diameter range by lateral arrangement on the lathe bed. As a result, there is no accompanying Diameter restriction above the face slide/tool carrier. Cross slide unit can be fully attached to the steady rests, HSSL and tailstock. This significantly reduces the set-u ...
DUPLO ISADDLE 10/60i Year: 2012 Paper Size : 356 x 610 / 120 x 210 mm Pile height per station : 65 mm Paper weights : 50 – 300 g/m² 2 towers Duplo 10/60i / 20 stations Dubble production possibility on trimmer, 6mm gap 4 stitching heads In production ready condition.
Weibert BS 750E profi Log band saw The log band saw is designed exclusively for sawing soft, hard, dry, wet and frozen materials, tree trunks or prismatic workpieces. Their length depends on the design of the machine. The material is placed on the supports of the rail track and fastened. The sawing unit is fed manually. Max. trunk diameter 750 mm Max. width of the boards 730 mm Max. cutting length 3,700 mm (3.7 meters), expandable! Min. cutting length 900 mm (0.9 meters) Saw blade stroke min./max. = 20/540 mm Max. cutting depth 220 mm Wheel diameter/width = 400/25 mm Motor power 7.5 kW (5.5 kW S1/100%) Motor power height adjustment 0.12 kW Saw blade length 3,600 mm Saw blade speed 15 m/s Total length of the basic version 4,600 mm (4.6 metres) Weight approx. 450 kg Optional for an extra charge: Extension section 2.3m Aspirator Lathe rod
Key data: 500 mm, 450 mm, 400 mm
5 Axis CNC Machining Center Universal CNC Milling Machine DMG Ecoline DMU 50 eco Year of construction: 2011 Siemens Sinumerik Conveyor Complete documentation 5-axis machining of simple to highly complex workpieces. Swivel rotary table Powerful milling spindle 8,000 rpm Tool Changer with 16 Places Pick-up Magazine Direct position measuring system and centrally lubricated roller circulation guide for high long-term accuracy. Ball screw in the linear axes The machine is in excellent condition and is still energized.
Cup wheel Ø: 180 mm Cup wheel speed: 2900 rpm electr. Connection: 380 V, 2900 rpm, 0.9 kW Vibration table dimensions: 200 x 350 mm Tilting Swinging Table Swing table swivels by +/- 20° Dimensions: 750 x 350 x 1270 mm
2 pieces of numbering machines for rotary and flat bed printing presses. Both are forward turning.
Key data: 4 , 240 mm, 130 mm
SPECIFICATIONS: Feed length: 2500 mm Machining width: 240 mm Processing height: 130 mm Spindles: Ø 40 mm Number of Spindles: 4 Shaft drive (2.9 kW) Installed power: 24 kW Voltage: 380 V CONFIGURATION OF THE SPINDLES: I bottom (5.5 kW) II right (7.5 kW) III left with electronic sideshift (7.5 kW) IV top (7.5 kW) EQUIPMENT: Complete with tools
The machine underwent a general overhaul in 2015 The following tasks were performed as part of the overhaul: repair of the electrical cabinet and hydraulics, scraping of the bed and table, replacement of bearings in the headstock, new springs for the axial bearings, new table piston rod and sleeves, installation of sludge separators. Documentation for the machine is available. Year of manufacture: 1980.
Width 76 cm Year of construction 2000 Flat pile feeder with Vaculift and Vacubelt Counting device MPC 6 fold pockets in the parallel fold section Downstream knife shaft 2 folding swords in the crossfold section Noise Insulation Hood Standing sheet delivery SAP 46 L Delivery date: immediately from stock Price on request. We supply and install worldwide.
Machine is in good working condition. Parts shown by hand not come.
Key data: 630 mm, 8
A used gear pusher Lorenz S8/630 with interchangeable wheels.
maximum number of results exceeded
please refine your search
