wmw karl marx used for sale

Hobs, tooth gear cutters for hobbing machine WMW / PWS Type G Module 3 ( Module3 ) HSS / Co TGL 29-8002 Bore Ø 40 mm New !' Dimensions: 110 x 100 x 100 mm

MAX DIAM 200

faceplate diameter: 3500 mm turning diameter: 4000 mm centre distance: 16000 mm turning speeds: 0,71-33,5 U/min Rest: 2 tailstock quill taper MT: max. workpiece weight -without tailstock: 6300 kg max. workpiece weight between centres: 18000 kg Plate area: mm total power requirement: 31 kW weight of the machine ca.: 60 t dimensions of the machine ca.: 22x5x4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hobs, tooth gear milling machine for hobbing machine WMW / PWS type G module 1.5 HSS / Co TGL 29-8002 bore Ø 27 mm New !' Dimensions: 58 x 69 x 69 mm

WMW - VEB PEEV 40/11 Capacity: 40 ton Weight: 2400 kg

Hobs, tooth gear milling machine for hobbing machine WMW / PWS ( WMW/PWS ) Type K Module 2,25 1575 HSS / Co TGL 29-8002 Bore Ø 27 mm New !' Dimensions: 70 x 70 x 58 mm

max. wheel diameter: 400 mm gear width: 275 mm max. module: 6 Overall size: 300x330x245 cm weight of the machine ca.: 5,5 t dist. cutter spindle - workpiece spindle: 40/265 mm hob turning speeds: 50-400 U/min Specification: Max wheel diameter: 400 mm Min module: 1 Max module: 6 Table diameter: 370 mm Max wheel diameter: -With counterstay: 340 mm -Without counterstay: 400 mm Max axial offset: 275 mm Max tangential adjustment: 100 mm Tooth helical angle: 45 degrees Max cutter diameter: 145 mm Max hobbing length: 170 mm Hob turning speeds capacity: 63-180 U/min Feeds infinitely variable axial: 0,2-10 mm/U Feeds infinitely variable tangential: 0,1-5 mm/U Radial for spur gears: 0,1-4 mm/U Radial for worm gears: 0,025-1 mm/U Rapid traverse axial: 500 mm/min Rapid traverse tangential: 250 mm/min Radial for spur gears: 400 mm/U Radial for worm gears: 100 mm/U Motor power: 7.4 kW The data for t ...

Hobs, tooth gear milling machine for hobbing machine WMW / PWS ( WMW/PWS ) Type G Module 1.5 1844 HSS / Co TGL 29-8002 Bore Ø 27 mm New !' Dimensions: 69 x 69 x 58 mm

Offer 24177 Specifications: - Tip height 180 mm - Center width 1000 mm - larger circulation – Ø over bed 355 mm - via flat sleds approx. 200 mm - Spindle bore 36 mm - Pick-up cone of the tailstock quill MK 5 - Travel of the tailstock quill 260 mm - Spindle speeds 18 - 1800 rpm -Feeds - Travel of the cross slide approx. 200 mm - Travel of the upper slide approx. 115 mm - Drive 400 V / 5.8 kW - with: - Tailstock, 3-jaw lining, bezel - Steel holder, moving center punch, - Chip tray - Space requirement approx. W 2500 x H 1500 x D 1200 mm - Weight approx. 2100 kg

Hobs, tooth gear milling machine for hobbing machine WMW / PWS type G module 2 0175 HSS / Co TGL 29-8002 Bore Ø 32 mm New !' Dimensions: 80 x 80 x 71 mm

Hobs, tooth gear milling machine for hobbing machine WMW / PWS ( WMW/PWS ) Type G Module 2 0191 HSS / Co TGL 29-8002 Bore Ø 32 mm New !' Dimensions: 80 x 80 x 71 mm

Hobs, tooth gear milling machine for hobbing machine WMW / PWS ( WMW/PWS ) Type G Module 2 0510 HSS / Co TGL 29-8002 Bore Ø 32 mm New !' Dimensions: 80 x 80 x 71 mm

x-travel: 1600 mm : ja weight of the machine ca.: 13,7 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Hobs, tooth gear milling machine for hobbing machine WMW / PWS ( WMW/PWS ) Type G Module 1.5 1432 HSS / Co TGL 29-8002 Bore Ø 27 mm New !' Dimensions: 69 x 69 x 58 mm

MAX CAPASITY 63 T, DIAMETER ROLLING 110

hobs, tooth gear hob for hobbing machine WMW / PWS type G module 2 0120 HSS / Co TGL 29-8002 bore Ø 32 mm New !' Dimensions: 78 x 78 x 71 mm

A WMW lead and feed spindle lathe that was overhauled in 1993 and has not been used since then is available. Center width: 1600mm, turning length: 1600mm, turning diameter: 250mm, turning diameter over bed/cross slide: 450mm/250mm, steel holder surface X/Y: 140mm/140mm, steel cross-section: 25mm/25mm. Speed: 2240rpm, spindle bore: 45mm, faceplate diameter: 450mm, quill stroke: 160mm, max. workpiece weight: 800kg/1250kg, max. journal diameter: 60mm. Including taper turning device, coolant device and quadruple steel holder. Documentation available. On-site inspection is possible. The machine was not used after its overhaul in 1993.

Turning diameter over bed/face slide: 630mm/340mm, turning length: 2000mm, center height: 290mm, clearance: 70mm, speed: 1180rpm, chuck: 400mm wedge bar chuck, tailstock: MK5, total power requirement: 15kW, machine dimensions X/Y/Z: approx. 5000mm/1350mm/1500mm, weight: approx. 4500kg. Including 2x 340mm steady rests, 2x medium steady rests, face plate with a diameter of 630mm, 2x face plates with cross slots, various tool holders, steady rest box, tool cabinet with additional tools, Heidenhain position indicator and 400mm key bar chuck. Documentation available. On-site inspection is possible.