windows cnc used for sale

Rotox Water Slot Mill

Length: 5000 mm Width: 100 mm Height: 2800 mm Year: 2011 0 Range+Heine coating system for coating individual wooden window components and frames for sale on behalf of a client ----------------------------------------------------------- Manufacturer’s technical description: Part dimensions: Length: 5,000 mm Height: 2,800 mm Width: max. 100 mm Coating system: Intended use of material from the relevant coating manufacturer with a low solvent content (VOC value), water-based and non-flammable. Capacity: min. 40 crossbars/shift, i.e. approx. 60 window units/shift (without forced drying) Process (1 cycle is run twice): - Flooding - Drying - Checking and applying joint sealant - Spraying - Drying -------------- -------------------------- Item 1 Conveyor technology 1 Power + Free circular conveyor Layout as per drawing 11-138-010a Essentially comprising: 3 drives with gear motors for the main  ...

Year: 2006 - technically efficient, ready to work – after full service - flash limit: 2 mm - angle range: 30-180 degrees - large heater - side supports - air preparation station

Technical data: heated blades, welding bead limitation 0.2 mm, optimisation of the welding result by means of parallel thrust welding processes, individual setting of the welding parameters, quick change of the outer contour allowances by means of holding magnets. Air consumption at 6bar: 15l/stroke, angle adjustment range: 30-180°, profile height: 30-105mm, max. profile width at 90°: 157mm, compressed air connection: 8.7bar, power: 2.7kW, mains voltage: 220V, 50/60Hz, length: 770mm, width: 880mm, height: 1560mm, weight: 320kg.

Double mitre saw Haffner DGS 1873400 for PVC profile blanks Technical data: Built in 1994 Diameter of the saw blades mm 500 2 motors per Kw 2.2 - speed 2800 Cutting length max mm 3400 Cutting length min mm 230 Cutting depth approx. mm 150 Swivel range 45-90 degrees Hydropneumatic saw feed Pneumatic workpiece clamping Control panel with double buttons 2 suction nozzles diameter mm 120 Compressed air 6 bar Overall dimensions mm 4600 x 1300 x 1650 h Weight kg 550

In need of repair - temperature controller defective! Single Head Welding Machine Technical data: heated blades, welding bead limitation 0.2 mm, optimisation of the welding result by means of parallel thrust welding processes, individual setting of the welding parameters, quick change of the outer contour allowances by means of holding magnets. Air consumption at 6bar: 15l/stroke, angle adjustment range: 30-180°, profile height: 30-105mm, max. profile width at 90°: 157mm, compressed air connection: 8.7bar, power: 2.7kW, mains voltage: 220V, 50/60Hz, length: 770mm, width: 880mm, height: 1560mm, weight: 320kg.

Glazing bead saw: Sawing Units 1 Length of scanning rod 1,500 mm and 3,000 mm Cutting length max 90 mm Diameter saw blade 175 mm Cutting height 25 mm Support length 1,500 mm Main motor 0.5 kW Saw blades fixed 45° For plastics Pneumatic clamps Saw feed manual

Year: 2015 - technically efficient, ready to work – after full service - two pneumatically tiltable beams (retaining and pressing) - through-feed - adjustable height: 500 mm (liftable) - adjustable vertical angle from 0 to 7 degrees - working width: 3500 mm

Year: 2014 - technically efficient, ready to work – after full service - motor: 2 x 0.75 kW - pneumatic clamping of the strips - discs with undercutting cutters (2 x 250 mm, 2 x 150 mm) - glass simulator – lateral strip support – stepless (adjustable with a crank and counter) adjustment of the simulator position - manual height adjustment of the work table

Year: 2014 - technically efficient, ready to work – after full service - working dimensions: 2750 x 1300 mm - tilting stop pins - pneumatically tilted - sliding/brush strips

Year: 2006 - technically efficient, ready to work – after full service - screwdriver - automatic screw feeding system - tilting table top - fittings punch (straight cut)

Year: 2014 - technically efficient, ready to work – after full service - working dimensions: 2750 x 1300 mm - tilting stop pins - pneumatically tilted - sliding/brush strips

- technically efficient, ready to work – after full service - adjustable leg height - working length: 3500 mm - roller width: 240 mm

- technically efficient, ready to work – after full service - adjustable leg height - working length: 3500 mm - roller width: 240 mm - measurement reading scale - manually adjustable stop + locking lever

Window suspension conveyor Tiger Surface area on the ceiling approx. 8.50 m x 3.20 m 20 hooks with 2 points already dismantled and ready for loading Shipping Dimensions 1 pallet 2800 mm x 800 mm x H 500 mm Weight 119 kg 1 pallet 1200 mm x 800 mm x H 600 mm Weight 120.5 kg

- technically efficient, ready to work – after full service - motor: 0.55 kW - working range: 410 x 110 mm - pneumatic profile clamping - pressure reducer

Year: 2007 - technically efficient, ready to work - after full service - pneumatically operated rotary table -90°/0°/+90° - working range: 200 x 240 x 2500 mm - 4 kW motor - speed ​​control (inverter) - 2 electronic position indicators - pneumatic profile clamping - cooling and lubrication system - copying template

Year of construction: 2025. Includes keyboard and mouse. Auction-ID: A1-49846-455

230V. Auction-ID: A1-49846-465

Year of construction: 2025. Includes keyboard and mouse. Auction-ID: A1-49846-461

Year of construction: 2025. Includes keyboard and mouse. Auction-ID: A1-49846-459

230V. Auction-ID: A1-49846-458

Year of construction: 2025. Includes keyboard and mouse. Auction-ID: A1-49846-466

Year of construction: 2025. Without monitors, keyboard and mouse. Auction-ID: A1-49846-470

230V. Without monitors. Auction-ID: A1-49846-468

Year of construction: 2025. Includes keyboard and mouse. Auction-ID: A1-49846-464

Year of construction: 2025. Includes keyboard and mouse. Auction-ID: A1-49846-463

Year of construction: 2025. Includes keyboard and mouse. Auction-ID: A1-49846-456

Year of construction: 2025. Without monitors, keyboard and mouse. Auction-ID: A1-49846-469

Year: 2002 New-exhibition machine, never used in production. - 3 motors - pneumatic profile clamping - adjustable milling length

This lot has not been tested for functionality. Parts may be damaged or missing. The dimensions, weights and other data given are to be understood as non-binding guideline values. No liability is assumed for the accuracy of the information ; Auction-ID: A1-50030-20

This lot has not been tested for functionality. Parts may be damaged or missing. The dimensions, weights and other data given are to be understood as non-binding guideline values. No liability is assumed for the accuracy of the information ; Auction-ID: A1-50030-19

Year: 2002 New-exhibition machine, never used in production. - handle function - copying template - pneumatic profile mounting - centering device

DAF LF45 4x2 truck, built in 2004, equipped with a specialized transport body with vertical racks, suitable for transporting glass, windows, doors, veranda elements and aluminum joinery. Equipped with a 3,920 cc diesel engine with an output of 123 kW (approx. 167 hp), Euro 3 emission class and 5-speed manual gearbox. Odometer reading: 193,754 km. Equipped with 3 seats and air suspension with DAF remote control for height adjustment and memory settings. Own weight 4,740 kg, GVW 6,500 kg and payload approximately 1,760 kg. Belgian vehicle documents available. Vehicle starts, drives and brakes properly. Last inspection shown was valid until 01/02/2026. Auction-ID: A3-46124-22081

Control: SIEMENS 840D Max.turning length: 450 mm Max swing diametr over bed/Slide: 500 mm/375mm Workpiece diametr: 246 mm Material passage through the spindle: 0 mm Rotation speed(max.) 6000 rpm Quick Change Toolposts:12 Taper ? VDI30 Coolant tank:175l M

Control: Heidenhain Max.turning length: 450 mm Max swing diameter over bed/slide: 500 mm/375mm Workpiece diametr: 246 mm Material passage through the spindle: 0 mm Rotation speed(max.) 6000 rpm Quick Change Toolposts:12 Taper ? VDI30 Coolant tank:175l Ma

OPTIMUM - OPTImill F 105 CNC Offer details Stock number 1039-8705 Machine Type Machining Center - Vertical Manufacturer: OPTIMUM Type OPTImill F 105 CNC Year of construction 2019 Control Sinumerik 808D adv. Siemens Additional Information CNC Machining Center Vertical OPTIMUM - OPTImill F 105 CNC - DEMONSTRATION MACHINE Technical details x-travel 550 mm y-travel 305 mm z-travel 460 mm Control Sinumerik 808D adv. Siemens Main spindle: Speed range - main spindle 10 - 10,000 rpm Drive power - main spindle 11 / 7.5 kW Max. torque 70 / 48 Nm Tool holder BT 40 Work table: Table clamping area 800 x 320 mm max. table load 300 kg T-slots 3x 14 x 100 mm Distance spindle / table 100 - 600 mm Tool Changer: Number of tool positions 12 pos. Tool holder BT 40 max. tool diameter 70 mm max. tool weight 6.0 kg Tool-tool changeover time 7.0 sec Feeds: Rapid traverse  ...

4 GUIDEWAYS LIVE TOOLS C AXIS CNC Siemens Sinumerik Center height mm 450 Max. swing diameter mm 800 Max. turning diameter mm 600 Center distance mm 8.290 TRAVELS X-axis travel mm Z-axis travel mm 8,400 Y-axis travel mm +/-15 mm SPINDLE Spindle nose mount ASA 11'' 4-jaw independent chuck diameter mm 700 Bar passage mm TURRET 12 positions Model Baruffaldi VDI 60 Live tools 6 positions MOTORIZED TAILSTOCK Quill diameter mm DIMENSIONS: Overall size mm 12.740x3.080xH 1.725 Weight COMPLETE WITH: Heidenhain optical scale Z axis n.1 steady rest diameter mm 320 n.1 steady rest diameter mm 600 n.1 steady rest diameter mm 740 Chip conveyor Auction-ID: A1-48745-13

Machine number: 2355 Operating voltage: 400 V Frequency: 50 Hz Rated current: 125 A Connection: 45 kW Control: SIEMENS SINUMERIK Center height: 320 mm Center width: 3000 mm Max. grinding length: 3000 mm Grinding spindle diameter: max. 620 mm Grinding spindle tool holder: 80 mm diameter, taper 1:5 Swivel capability: +- 10° Workpiece spindle bore: MORSE K 6 mm Swivel capability: +30° incl. extensive item spare parts and accessories, documentation, grinding wheels, belt filter system, extraction and filter Hours read: 2667 Attention: the machine can be transported on a standard truck up to 3000 mm wide ! Auction-ID: A7-49089-231

Machine number: 2356 Operating voltage: 400 V Frequency: 50 Hz Rated current: 125 A Connection: 45 kW Control: SIEMENS SINUMERIK Center height: 320 mm Center width: 3000 mm Max. grinding length: 3000 mm Grinding spindle diameter: max. 620 mm Grinding spindle tool holder: 80 mm diameter, taper 1:5 Swivel capability: +- 10° Workpiece spindle bore: MORSE K 6 mm Swivel position: +30° incl. extensive batch Tips in different sizes, matching steady rests, documentation, belt filter system, suction Hours read: 2355 Attention: the machine can be transported on a standard truck up to 3000 mm wide ! Auction-ID: A7-49089-235

Manufacturer: BURKHARDT + WEBER GmbH Model (Typ): MC 100 S0 Machine Type: CNC Horizontal Machining / Boring Center (floor-type) Country: Germany Delivery Date: July 1992 Series: MC Series (Modular Machining Centers) Travels X (Column travel): ~3,000 – 5,000 mm Y (Vertical): ~2,000 – 2,500 mm Z (Ram): ~800 – 1,200 mm W (Spindle quill): ~500 – 800 mm Spindle Diameter: 100 mm (this is what MC 100” refers to) Spindle Taper: ISO 50 / SK50 Spindle Speed: ~2,000 – 3,000 rpm Main Motor Power: ~30 – 50 kW Auction-ID: A1-49922-14

32 fold tool changer. Main spindle 50- 9200 rpm X shaft 700 mm Y shaft 315 mm Z shaft pinole controlled 172 mm Includes tool drawer Z axis (hand 180 mm) W shaft (Machine head) 495 mm Rapid traverse 9 mtr/min Auction-ID: A1-47360-147

X shaft 700 mm Y shaft 315 mm Z shaft pinole controlled 172 mm Z shaft manual pinole 180 mm W shaft ( Machine head ) 495 mm 4th axle 360 x 0,001 gr with against center. Table size 1230 x 410 Spindle holder SK 30 / DIN 69871A Includes tool drawer Auction-ID: A1-47360-148

Machine type: Vertical machining center Control: Heidenhain, Table load: 500 kg Tool magazine: 24 places The dismantling must be carried out by one of the partner companies mentioned. The costs for this are to be requested by the buyer himself. Auction-ID: A1-50085-3

Used, untested. Documentation and instruction manual available. Equipped with automatic stop. Loading conditions: Is loaded onto the truck Forklift and crane available Auction-ID: A7-50094-12

Technical data: Turning diameter over bed: 1260 mm Turning diameter at opening: 2700 mm Turning diameter at the pit: 3800 mm Turning diameter via slide: 900 mm Turning length: 4000/5000 mm

Technical data: Diameter over bed: 625 mm Turning length: 1500 mm Diameter via slide: 325 mm Spindle head shape: Cam-Lock Spindle drilling diameter: 105 mm

The machine is equipped with controlled B-axis smallest delivery 0.001, swivel range 340, controlled workpiece spindle stick (C-axis)smallest delivery 0.05, max. 42 rpm, equipped with an external grinding spindle (left and right spindle end), 1 internal grinding spindle. For an additional charge, a second internal grinding spindle can be delivered. Z-way 680 mm, X-way 255 mm, smallest delivery of the axles 0.001 mm. Tip height 175 mm, W.-stock MK 5, step. adjustable 1 - 1200 rpm, external grinding spindle 1000 - 3000 rpm, max. grinding wheel perm. 300 mm. The machine is suitable for ideal for the processing of carbide and technical ceramics (SIC and Al 2). Intermediate sale:reservations Delivery time:4-6 months

Manufacturer Heckler & Koch Model AM 444 A Power consumption: 5.5 KW Voltage: 380/400 Volts Spindle holders for vertical and horizontal spindles: 40 Slide movement x = 410nn y = 350mm z = 400mm Vertical clamping table 850 x 255 mm Feed range 0-1500 mm/min Sliding gearbox 12-stage Speed: 63-2800 rpm Step jump 1.4 CNC control CNC 783/m Dimensions (HxWxD) 1.800x2.400x1.700mm Weight 1,500 kg Ref.Nr PLW18 Mistakes reserved!

Technical data: The machine is completely overhauled in 2011 with new electrics, new wiring, including new control SIEMENS Sinumerik 840D max. circulating and turning diameter: 2,000 mm max. turning height: 1,500 mm Sheet disc diameter: 1,600 mm max. table load: 11.20 to. Cross-beam adjustment: 1,170 mm