We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
120,455 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
ISO-K-KF Reducing T PFEIFFER VACUUM TR-9990-04985 Nominal diameter: DN 63 ISO-K nominal diameter ( reduced ): DN 25 ISO-KF installation length: 340 mm Material: Stainless steel 1.4301 / 1.4307 New Dimensions ( reducing tee ): 340 x 120 x 95 mm Dimensions ( packaging ): 350 x 125 x 100 mm
used
Level switch, float switch, level monitor, level switch WOERNER KFV-A/39D933/950/175/745 407795 1 Switching point Immersion depth: 950 mm Flange diameter: Ø 80 mm bolt circle diameter: Ø 65 mm 4x bore: Ø 6 mm Switching capacity: max. 250 V UC, 1.0 A, 40 VA, 40 W Material tube: Brass Float material: Stainless steel New ! Dimensions (level switch): 1040 x 80 x 80 mm
used
Compact radiators, profile compact radiators KERMI Type: 33/900/1200 Article number: FK0330912 three-row, three convectors, serial flow with cladding and mounting material Dimensions ( radiator ): 1200 x 155 x 900 mm New ! Dimensions: 1250 x 200 x 950 mm
used
CV drive shaft, cardan shaft, propeller shaft PAGUS length: approx. 830 - 950 mm shaft outside Ø 70 mm flange Ø 152 mm bolt circle Ø 1128 mm 6x bore Ø 12.5 mm New ! Dimensions: 870 x 160 x 160 mm
used
Repair kit GRUNDFOS 98923302 Kit, maint DMX226-280 Material: PVC/EPDM 226L, 226M, DN20 316 stainless steel, EPDM New, with documents Dimensions ( packaging ): 175 x 135 x 60 mm
used
Repair kit, maintenance kit GRUNDFOS Kit valves/diaphragm PVC/E/C 97751473 SD-S-PVC/E/C-1 for DD(E/C/A) with standard valve New, with documents ! Dimensions ( packaging ): 230 x 220 x 35 mm
used
Sauglanze PAGUS 900 mm Material: PVC Immersion depth: 900 mm connection thread : 1 1/4 ( inches ), inner diameter: Ø 20 mm thread for fastening: 2 ( inches ), length: 25 mm 2x level switch: 0 - 300 mm foot valve diameter: Ø 32 mm New ! Dimensions ( suction lance ): 1040 x 120 x 115 mm
used
Cardan shaft, propeller shaft ELBE length: approx. 940 - 1040 mm 150/8-S=935/X=110 0.0.br 117.110.0 shaft Ø 64 mm shaft outside Ø 100 mm flange Ø 150 mm New Dimensions: 950 x 150 x 150 mm
used
Chip conveyor, hinged plate conveyor, chip conveyor, hinge belt conveyor SILISTRA TC 280 x 900 ( TC280x900 ) Inlet hopper height: 230 mm inlet: 2880 mmbr /br / inlet: 2880 mm 0 x 900 mm Belt width: 400 mm Height discharge: 1000 mm 220 / 380 V used, tested ! Dimensions: 2700 x 750 x 1350 mm
used
Safety valve, flange safety valves, pressure relief valve ARI ARMATUREN Figure 901/902 3,8 bar TÜV.SV.87-663.36.D/G.0,74.3,8 bar TÜV.SV.85-729.36.F.0,54.3,8 bar inlet: DN40 Flange diameter: Ø 152 mm outlet: DN65 Flange diameter: Ø 185 mm New ! Dimensions: 200 x 190 x 540 mm
used
Solenoid valve, directional control valve BUSCHJOST, IMI, NORGREN 8251164.9150 0000000.9150 0.3 - 12 bar G3/8 ( inch ) 24 V DC, 15 Watt New, with documents ! Dimensions ( valve ): 85 x 65 x 42 mm Dimensions ( packaging ): 130 x 110 x 50 mm
used
Solenoid valve, directional control valve HERION 9203000 Mounting length: 60 mm Connections: 1/2 ( inch ) Control solenoid: 0200 24 V DC 12 W / 48 V AC 50 Hz 15 VA New ! Dimensions: 96 x 66 x 33 mm
used
Solenoid valve, directional control valve BUSCHJOST, IMI, NORGREN 8240200.9101.02400 0000000.9100 0.1 - 10/16 bar G1/2 ( inch ) installation length: 67 mm 24 V DC, 8 Watt New, with documents ! Dimensions ( valve ): 81 x 67 x 44 mm Dimensions ( packaging ): 190 x 100 x 40 mm
used
Hand lever press, mandrel press, rotary mandrel press LINING (LONDON) LIMITED. No 900-0000 Projection: 140 mm stroke: max. 65 mm table: 60 x 81 mm, tool holder: Ø 38 mm ram diameter: Ø 32 mm, tool holder: Ø 18 mm with punching tool: Ø 13 mm and material hold-down device ( adjustable ) used, checked! Dimensions ( ready for use ): 270 x 160 x 670 mm
used
Slewing ring, slewing ring, ball slewing ring, slewing gear PAGUS Ø 1100 mm x 80 mm Upper ring: Outer diameter: Ø 1125 mm, bolt circle diameter: Ø 1075 mm Lower ring: Outer diameter: Ø 1100 mm, bolt circle diameter: Ø 1060 mm Inner diameter: Ø 975 mm Height: 80 mm 8x bore: Ø 17.5 mm per ring As good as new ! Dimensions: 1125 x 1125 x 80 mm
used
Tapered roller bearings, roller bearings, ball bearings TIMKEN 32006XM-90KM1 4 pieces Inner diameter: Ø 30 mm Outer diameter: Ø 55 mm width: 17.5 mm originally packed unused ! Dimensions (package): 120 x 65 x 65 mm
used
hobs, sprocket hobs WMW / PWS ( WMW/PWS ) type BP II ( BPII ) chain pitch 9,25 rollers Ø 5 mm 9317 HSS / Co bore Ø 27 mm New ! Dimensions: 70 x 70 x 57 mm
used
Hob WMW / PWS ( WMW/PWS ) Type G pitch 3 HSS 9560 20° TGL 29-8002 bore Ø 40 mm New ! Dimensions ( cutter ): 108 x 100 x 100 mm Dimensions ( packaging ): 115 x 115 x 120 mm
used
Hobs WMW / PWS ( WMW/PWS ) Type G pitch 3,5 HSS 9560 20° TGL 29-8002 bore Ø 40 mm New Dimensions ( cutter ): 108 x 100 x 100 mm Dimensions ( packaging ): 115 x 115 x 120 mm
used
Slip-on milling cutters, face milling cutters, corner milling cutters, milling head JONGEN WERKZEUGTECHNIK 90PP-050-128-6 diameter: 50 mm Number of cutting edges: 6 Diameter base body : 48 mm height: 40 mm diameter (bore): 22 mm Plate seat: B4 New ! Dimensions ( cutter ): Ø 48 x 40 mm dimensions ( transport box ): 62 x 57 x 57 mm
used
Slip-on milling cutters, face milling cutters, corner milling cutters, milling head JONGEN WERKZEUGTECHNIK 90PP-80-128 Diameter: 80 mm Number of cutting edges: 8 diameter Base body : 78 mm height: 50 mm diameter (bore): 27 mm plate seat: B4 New ! dimensions ( cutter ): Ø 78 x 50 mm dimensions ( transport box ): 100 x 90 x 60 mm
used
Corner milling cutters, end mills JONGEN WERKZEUGTECHNIK 90PP-28-10-4 Diameter: 28 mm Number of cutting edges: 4 Shaft diameter: 25 mm Length: 100 mm Usable depth: 51 mm Plate seat: B3 New ! Dimensions ( cutter ): Ø 28 x 100 mm Dimensions ( transport box ): 115 x 38 x 34 mm
used
Screw-in milling cutters, face milling cutters, corner milling cutters JONGEN WERKZEUGTECHNIK 90PP-022-15 Diameter: 22 mm Number of cutting edges: 2 Shank diameter: 25 mm length: 100 mm Usable depth: 32 mm thread: Ø 25 x 14 mm, pitch: 1,1,25 New ! Dimensions ( cutter ): Ø 25 x 100 mm dimensions ( transport box ): 106 x 38 x 34 mm
used
Corner cutters, end mills JONGEN WERKZEUGTECHNIK 90PP-20-77-2 Diameter: 20 mm Number of cutting edges: 2 Shaft diameter: 25 mm Length: 100 mm Usable depth: 26 mm Plate seat: B13 New Dimensions ( cutter ): Ø 25 x 100 mm Dimensions ( transport box ): 105 x 38 x 34 mm
used
End mills, milling cutters JONGEN WERKZEUGTECHNIK 90TF-028-15 Diameter: 28 mm Number of cutting edges: 2 Diameter shank : 25 mm Usable depth: 44 mm Total length: 100 mm New ! Dimensions ( cutter ): Ø 28 x 100 mm Dimensions ( transport box ): 110 x 42 x 36 mm
used
High-pressure pump, plunger pump PLATZ® REINIGUNGSSYSTEME GmbH Type 304 920 Q: max. 45 l/min p: max. 100 bar necessary drive power: 8,,2 kW Speed (pump shaft): 450 rpm Connections: Ø 25/ 30 mm ( inside ) Flange diameter: Ø 230 / 300 mm bolt circle diameter: Ø 265 mm 4x threaded bolt: M12 x 1.75, usable length: 35 mm material (pump heads): brass new ! Dimensions: 410 x 320 x 500 mm
used
Fan motor, three-phase electric motor LEROY SOMER, EMERSON 6P CM29/T ( 6PCM29/T ) 1,1,4 kW 950 rpm 400 V 3AC IP 55 shaft diameter: Ø 19 mm flange: 258 x 146 mm New ! Dimensions ( engine ): 390 x 260 x 190 mm Dimensions ( packaging ): 420 x 300 x 280 mm
used
Hydraulic pump COMMERCIAL / INTERTECH M22 26 313 9610 514 001 ( M22263139610514001 ) Continuous pressure 250 bar Peak pressure 350 bar shaft: 32mm shaft length: 50mm dimensions 210 x 180 x 140 mm
used
Four-wire rotary joint, housing part ROEMHELD, HILMA, STARK 9284036 NW5 Pressure range: 10 - 500 bar max. operating pressure: 500 bar Number of passes: 4 Bearings: plain bearing speed: max. 48 rpm hydraulic connection: G1/4 New ! Dimensions: 88 x 85 x 85 mm
used
Rubber-cork gasket, 10 pieces SCHUNK 9612791 PGN 160 Deckel Material: Rubber - Cork - Mixture Material thickness: 0.75 mm New ! Dimensions ( packaging ): 190 x 120 x 10 mm
used
Three-phase electric motor VEM K20R 80 K 6 H ( K20R80K6H ) 0,0,75 kW 935 rpm 230 / 400 V 3AC 50 Hz IP 55 Design: B3 Shaft diameter: Ø 22 mm Wavelength: 50 mm Groove width: 6 mm Motor base: 125 x 153 mm hole spacing ( parallel to shaft ): 100 mm hole spacing ( transverse to shaft ): 125 mm hole diameter: Ø 10.5 mm New ! Dimensions: 275 x 155 x 200 mm
used
Activated carbon filter with protective grille TEKA 970545 Filter dimensions: 305 x 305 x 70 mm Protective grille dimensions: 305 x 305 x 24 mm New ! Dimensions: 310 x 310 x 100 mm
used
Tank Ausgestattet mit: Schauglas im Oberboden Kombinationsventil Reinigung/Co² Scheibenventil DN32 Nw32 Number available (price per tank): 7 Diameter [cm]: 90 Height [cm]: 210 capacity liter: 900 More then 300 machines new and second hand on our seema .de
used
Turnbuckle with 2x clevis PAGUS 830 - 950 mm thread: M20, pitch: 2.5 2x clevis head: 40 x 40 x 105 mm inner width: 21 mm, inner length: 65 mm for bolts: Ø 16 mm wrench width: 30 / 36 mm Material: Steel, galvanized New ! Dimensions (packaging): 900 x 40 x 40 mm
used
Fan Impeller, Axial Impeller WINGFAN P9TR Diameter: Ø 990 mm Necessary shaft diameter: Ø 48 mm Wavelength: 112 mm Groove width: 14 mm Hub diameter: Ø 100 mm hub length: Ø 70 mm New ! Dimensions: 9990 x 990 x 210 mm
used
Control console, text display, digital display LAUER, PULSOTRONIC PCS 900 ( PCS900 ) 8450-6300 24 V DC 20 VA for front panel installation: 304 x 168 mm New, with documents ! Dimensions: 326 x 190 x 65 mm Dimensions ( Packaging ): 380 x 260 x 90 mm
used
Electric motor, three-phase motor -Power: 0.6 kW -Speed: 925 rpm -Shaft: Ø 18 mm -Construction: B3 -Protection class: IP 44 -Number: 6x motors available -Price: per piece -Dimensions: 360/170/H240 mm -Weight: 24 kg
used
Gear motor, electric motor, stop motor, drive motor, crane motor, bridge crane -Manufacturer engine DEMAG type: KBA-112-MB-6 -Manufacturer engine DEMAG type: KBL-71-A4 -Manufacturer gearbox DEMAG type: FG08-B-14-U-0-H1- -Power: 0.3/2.9 kW -Speed: 106/945 rpm -Construction: B14 -Diameter shaft: Ø 28 mm -Protection class: IP 54 -Dimensions: 670/300/H500 mm -Weight: 102 kg
used
Three-phase motor, electric motor -Power: 16 kW -Speed: 980 rpm -Construction: B3 -Protection class: IP 54 -Dimensions: 750/480/H400 mm -Weight: 223 kg
used
Electric motor, three-phase motor -Electric motor: Type 80/S6 -Power: 0.37kw -Speed: 920 rpm -Shaft: Ø 19 x 40 mm -Construction: B3 -Protection class: IP 54 -Dimensions: 280/160/H210 mm -Weight: 9 kg
used
Screws, hexagon head screws, cylinder head screws with hexagon socket, Allen screw -Hexagon head screws: M20, DIN 931 -Weight: 514 kg -Sizes/number: M20 x 45 to M20 x 100, see photo parts list -Quality: 8.8 black or galvanized -Manufacturer: various -Price: complete -Total weight: 534 kg M20 x 40 mm, galvanized, 4 packs of 25 pieces = 100 pieces M20 x 50 mm, galvanized, 12 packs of 25 pieces = 300 pieces M20 x 60 mm, galvanized, 20 packs of 25 pieces = 500 pieces M20 x 65 mm, galvanized, 20 packs of 25 pieces = 500 pieces M20 x 100 mm, galvanized, 19 packs of 25 pieces = 475 pieces M20 x 45 mm, black, 1 pack of 25 pieces = 25 pieces M20 x 50 mm, black, 8 packs of 25 pieces = 200 pieces M20 x 90 mm, black, 5 packs of 25 pieces = 125 pieces
used
Three-phase motor, electric motor -Manufacturer: VEM, electric motor type KR 112, 2/6./S -Power: 2.2kW -Speed: 940 rpm -Shaft: Ø 28 x 60 mm -Protection class: IP44 -Dimensions: 390/230/H255 mm -Weight: 41 kg
used
Electric motor, three-phase motor -Manufacturer: ZSE MEZ, electric motor type 4AP90s-6 -Power: 0.75 kW -Speed: 940 rpm -Shaft: Ø 24 x 50 mm -Type: B5 -Protection class: IP 54 -Dimensions: 290/175/H210 mm -Weight: 14 kg
used
Three-phase motor, electric motor, brake motor -Manufacturer: Kobold, electric motor brake motor type KOD 467 ma -Power: 0.12 kw -Speed: 920 rpm -Shaft: Ø 11 x 20 mm -Construction: B14 -Protection class: P 33 -Brake: 0.37 kp/m -Dimensions: 245/160/H115 mm -Weight: 6.0 kg
used
Three-phase motor, electric motor -Manufacturer: Kobold, electric motor type KOD 566 -Power: 0.18kw -Speed: 920 rpm -Shaft: Ø 14 x 30 mm -Construction: B14 -Dimensions: 205/175/H130 mm -Weight: 5.5kg
used
Shunt motor, three-phase motor, electric motor, motor for saddle stitchers, saddle stitching machine, speed-controlled, speed-controlled, slip-ring rotor, slip-ring rotor motor, brake motor -Handover: in the current condition as seen -Brense: out of order -Manufacturer: VEM, electric motor type BMRE 80 G 6 -Power: 1.1kW -Speed: 930 rpm -Shaft: Ø 22 x 50 mm -Construction: B3 -Protection class: IP44 -Dimensions: 345/155/H200 mm -Weight: 20kg
used
Three-phase motor, electric motor -Manufacturer: ADDA, electric motor type AE132S-5 -Power: 3/3.6 kW -Speed: 950/1140 rpm -Shaft: Ø 38 mm -Construction: B3 -Protection class: IP 54 -Price per piece -Number: 1x available -Dimensions: 440/260/H310 mm -Weight: 42kg
used
Electric motor, three-phase motor -Manufacturer: VEM, electric motor type DMK 5/6 RA -Power: 3.5 kW -Speed: 950 rpm -Shaft: Ø 28 x 60 mm -Construction: B3 -Protection class: P33 -Dimensions: 515/360/H285 mm -Weight: 77 kg
used
Shunt motor, three-phase motor, electric motor, motor for saddle stitcher, saddle stitcher, speed-controlled, speed-controlled, slip-ring rotor, slip-ring rotor motor -Power: 3.0kW -Speed: 930 rpm -Shaft: Ø 28 x 60 mm -Type B3 -Protection class IP44 -Price per piece -Quantity: 4 pieces -Dimensions: 535/235/H260 mm -Weight: 51kg
used
Electric motor, three-phase motor -Manufacturer: VEM, electric motor type KMR 132 S6 -Power: 5.5 kW -Speed: 955 rpm -Voltage: 380/660 V -Shaft: Ø 38/80 mm -Construction: B3 -Protection class: IP44 -Number: 2 motors available -Price: per piece -Dimensions: 470/250/H325 mm -Weight: 70 kg