wd 200 used for sale

Emergency generator set 200 kVA Volvo / WA-V 200 S Machine Execution: Unit type: Stationary Design: Soundproofed Technical data engine: Engine manufacturer: Volvo Engine type: TAD 733 GE Engine No.: 5312956418 Motor power: 201 KW Cooling: Water-cooled Power: Electric 12 V DC Speed: 1,500 rpm Fuel: heating oil or diesel B7 Technical data generator: Generator manufacturer: Leroy Somer Generator type: TAL 044 M M 6S/4 Gen.Nr.: 39786300005 Generator capacity: 200 kVA Voltage: 400 / 231 volts Power factor: cos. - phi 0.8 Speed: 1,500 rpm Switchgear: Version: Automatic start Tank: Design: Base frame tank with drip tray Dimensions of the unit: Width approx. mm: 1.200 Height approx. mm: 2.200 Length approx. mm: 3.600 Weight approx. KG: 3.550 Use: Condition: Demonstration machine Year of construction: 2023 Delivery time: immediatel ...

Three-jaw chuck, 3-jaw chuck -Mouth size: Ø 200 mm -Passage: Ø 54 mm -Weight: 12.6 kg

Three-jaw chuck, three-jaw lathe chuck, 3-jaw chuck -Feed size: Ø 200 m -Through hole: Ø 54 mm -Short cones: 5 -Bolt circle: 105 mm -Weight: 16.2 kg

Three-jaw chuck, 3-jaw chuck -Type: OM200-ZJ -Chuck size: O 200 mm -Passage: O 56 mm -Admission thread: M60 x 5.5 mm -Weight: 19.8 kg

Three-jaw chuck, 3-jaw chuck -Chuck size: Ø 200 mm -Passage: Ø 54 mm -Rezess: Ø 159 mm -Hole circle: 176 mm -Weight: 14.2 kg

Three-jaw chuck, three-jaw lathe chuck, 3-jaw chuck -Mouth size: Ø 200 mm -threaded mounting -Through hole: Ø 53 mm -Weight: 19.7 kg

Three-jaw chuck, 3-jaw chuck -Chuck size: Ø 200 mm -Hole circle: 156 mm -Passage: Ø 54 mm -Weight: 12.7 kg

Flange mounting, driving flange -Chuck flange with: driving pin -Outer diameter: 200 mm -Short taper mount for: bayonet disc mounting DIN 55027 -Cone size: 5 -Hole circle: Ø 104.8 mm -Weight: 9 kg

Three-jaw chuck, 3-jaw chuck -Chuck size: Ø 200 mm -Admission recess: Ø 168 mm -Passage: Ø 55 mm -Weight: 12 kg

TECHNICAL SPECIFICATIONS Designation: Discharge belt Version: stationary Axle distance: 6,000 mm Belt width: 1,200 mm Year of construction: 2006 Drive power: 15 kW Drive type: Plug-on gear motor Support: free supporting structure Catwalk: not available Handover: Transfer hood Belt tension: Tensioning carriage Galvanized version: yes SPECIFIC COMMENT - Exhaust conveyor belt with close upper belt stations - No trough angle / straight load flow

Pneumatic cylinder, standard cylinder, air cylinder, pneumatic piston, air piston -Stroke travel: 200 mm -Piston diameter: 43 mm -Piston rod: 25 mm -Total length: 390 mm -Total length extended: 590 mm -Price: per piece -Quantity: 2 available -Dimensions: 100/100/H390 mm -Weight: 6.5 kg/piece

Pneumatic cylinder, standard cylinder, air cylinder, pneumatic stamp, air stamp -Stroke: 200 mm -Piston diameter: 60 mm -Piston rod: 32 mm -Total length: 425 mm -Total length extended: 625 mm -Price: per piece -Number: 2x available -Dimensions: 150/150/H425 mm -Weight: 12.1 kg/piece

Micrometer, micrometer screw -Measuring range: 200 - 225 mm -without: test piece -Also other sizes: available -Weight: 1.4 kg

Electric motor, three-phase motor -Volt: 415 V. -Power: 0.063/0.4 kW -Speed: 460/2840 rpm -Shaft: Ø 17 x 35 mm -Construction: B14 -Protection class: IP 65 -Dimensions: 330/220/H170 mm -Weight: 9 kg

Three-jaw chuck, three-jaw lathe chuck, 3-jaw chuck -Chuck size: Ø 200 mm -Passage: Ø 55 mm -Weight: 12 kg

Used SMG HZPUX 350/200 - 1500/1300 moulding press in good condition! Main technical data: - Power: 510 ton - Maximum span with castle: 1460 mm - Minimum light with castle: 520 mm - Maximum span without castle: 2160 mm - Minimum light without castle: 1220 mm

Three-jaw chuck, 3-jaw chuck -Chuck size: Ø 200 mm -Passage: Ø 54 mm -with: base plate -Weight: 26 kg

Clamping table, clamping angle, T-slot table, rotary table, milling machine table -Table surface: 500 x 200 mm -4x T slots: 14 mm -Clamping angle: rotatable, swiveling, tiltable -Foot recording: mm -Dimensions: 500/300/H210 mm -Weight: 50.5 kg

Double bench grinder, double grinding machine, pedestal grinder, pedestal grinder -Motor power: 0.75 kW -Speed: 3000 rpm -Max. grinding wheels: Ø 200 x 32 mm -Operating voltage: 380 volts -Dimensions: 540/280/H1230 mm -Weight: 116 kg

Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 200 mm -Passage: Ø 50 mm -one set: hard interchangeable jaws -Weight: 15 kg

Three-jaw chuck, three-jaw lathe chuck -Mouth size: Ø 200 mm -hard: interchangeable jaws -Base plate for: machine table -Passage: Ø 54 mm -Weight: 22 kg

Ball Mill Vollrath EFC 200 Wet and dry grinding Ferrous grinding with steatite balls Lining hard porcelain Capacity 200 l Drive power 1.4 kW Speed 42 1/min 3 ball mills each mounted on steel structure Very good operational condition, directly from production!

turning diameter: 235 mm turning length: 200 mm turning speeds: 6500 U/min control: Siemens 840D swing diameter: mm turning height: mm workpiece height max.: 100 mm spindle bearing diameter: 90 mm spindle head: A5 total power requirement: 41 kW weight of the machine ca.: 6500 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Three-jaw chuck, three-jaw lathe chuck -without: interchangeable jaws -Mouth size: Ø 200 mm -Recess: Ø 162 mm -Bolt circle: 3 x 180 mm -Passage: Ø 52 mm -Weight: 13 kg

Three-jaw chuck, 3-jaw chuck -Type: DHB 200x3x5 TGL 30 2332 -Mouth size: Ø 200 mm -Passage: Ø 54 mm -max.: 3000 rpm -Short taper mount: Ø 105 mm -Weight: 24 kg

Clamping angle for workpiece clamping -Dimensions: 200/320/H220 mm -Thickness: 25 mm -Groove: 20 mm -Surface: milled -Weight: 22.7 kg

The scope of delivery includes: 01x Shelf connector, used Material color: blue Manufacturer: Feralco for shelf spacing: approx. 200 mm Total length: approx. 200 mm Profile abm.: approx. 20 x 20 mm Headstock: approx. 100 x 40 x 4 mm Borehole Ø: approx. 9 mm (2 pcs per side) Weight: approx. 0.41 kg | Pcs.

Function generator, oscilloscope -Frequency range: 0.2 Hz to 240 kHz -Dimensions: 225/225/H85 mm -Weight: 1.2 kg

Electric motor, three-phase motor -Volt: 415 V. -Power: 0.063/0.4 kW -Speed: 460/2840 rpm -Shaft: Ø 17 x 35 mm -Construction: B14 -Protection class: IP 65 -Price: per piece -Number: 3x available -Dimensions: 395/210/H190 mm -Weight: 7 kg

Lathe Manufacturer: Schaerer Model: UN 200 Center distance: 1600mm

Pneumatic cylinders, air cylinders, standard cylinders, clamping cylinders -Piston: Ø 50 mm stroke: 200 mm -Piston rod: Ø 20 mm -Quantity: 1x available --Dimensions: 65/65/H580 mm -Weight: 4.2 kg

Pneumatic cylinder, standard cylinder, air cylinder, pneumatic stamp, air stamp -Stroke: 200 mm -Piston diameter: 80 mm -Piston rod: 22 mm -Total length: 445 mm -Total length extended: 645 mm -Price: per piece -Number: 2x available -Dimensions: 96/96/H445 mm -Weight: 6.6 kg

Slotting machine Elmass for wedge tracks from 2.5-14mm. Thanks to the bore-guided tool, even extra-long keyways can be pushed. Tools for standard holes of 6-50mm and groove widths of 2.5-14mm are available. Wedge tracks in blind holes are also possible. Multiple wedge tracks thanks to the 400mm rotary table are feasible.

Pneumatic cylinder, standard cylinder, air cylinder, pneumatic piston, air piston -Stroke travel: 200 mm -Piston: Ø 40 mm -Piston rod: Ø 16 mm -End position damping: adjustable on both sides -Dimensions: 54/54/H400 mm -Weight: 2.2 kg

Pneumatic cylinder, air cylinder, standard cylinder -Stroke: 200 mm -Piston: Ø 50 mm -Piston rod: Ø 20 mm -Dimensions: 65/65/H450 mm -Weight: 3 kg

Pneumatic cylinder, standard cylinder, air cylinder, pneumatic stamp, air stamp -Stroke: 200 mm -Piston diameter: 50 mm -piston rod: 16 mm (connection M16 x 1.5 thread) -Total length: 383 mm -Total length extended: 583 mm -Price: per piece -Number: 1x available -Weight: 1.35 kg

Mazak Integrex 200 lll S + GL 150 F CNC turning-milling center with second spindle CNC control Mazatrol PC Fusion CNC 640 MT PRO Turning diameter 550/660 mm Turning length 1016 mm Spindle bore diameter 65 mm Spindle speed 35-5000 rpm X-axis travel: 580 mm Y-axis travel 160 mm Z-axis travel: 1045 mm B-axis travel: 225 ° mm C-axis indexing 360° Spindle nose A2-6 Tool cone Capto C6 Number of tools in the magazine 40 If you have any questions about the machine, as well as an appointment for a viewing, please contact us by phone or e-mail.

Dough filling and dosing machine Rheon KN 200 Cornucopia used Rheon KN 200 dough filling and dosing machine.The machine has been tested for function, can be viewed and tested in the warehouse in Bielefeld. We will be happy to send you further pictures and information on request. - Dough pieces: 10-300 gr. - Output : 10-60 pieces/min -digital control - Stainless steel cladding - rollable on wheels - used Rheon KN 200 for bakery confectionery

geared motor, electric motor -Speed: 40.5 rpm -Power: 0.55 kW -Design: B5 -Shaft diameter: Ø 25 mm -Protection class: IP 65 -Dimensions: 445/230/H210 mm -Weight: 26 kg

Gear motor, electric motor, three-phase motor -Speed: 19.5/78 rpm -Power: 0.1/0.4 kW -Construction: B3 -Diameter shaft: 20 mm -Protection class: IP 54 -Dimensions: 410/220/H210 mm -Weight: 21.9 kg

Execution: Aggregate type: stationary Execution: Soundproofed Technical data engine: Engine manufacturer: Volvo Engine: TAD 733 GE Engine No.: 5312982207 Power: 201 KW Cooling: Water-cooled Occasion: Electric 24 V DC Speed: 1500 rpm Fuel: Fuel oil EN 590 Technical data generator: Generator manufacturer: Leroy Somer Generator type: TAL044-M Gene. No.: 39664900008 Generator power: 200 kVA Voltage: 400 / 231 Volt Power factor: Cos. - PHI 0.8 Speed: 1500 rpm Switchgear: Execution: Automatic start Functions: Parallel operation Switch: Generator switch 4 poles Delivery: Built Tank: Execution: Base frame tank with drip pan Content / liter: 990 Dimensions of the power unit: Width approx. mm: 1.200 Height approx. mm: 2.295 Length app ...

Hand lever scissors, hand tin snips, tin snips, sheet metal snips -Hand lever shears -Material thickness: max. 2 mm -Blade length: 200 mm -Dimensions: 790/540/H1715 mm -Weight: 28 kg

Bending tool, die, upper knife, upper tool, straight tool -Tool for: press brake -Tool as: die -Thickness: 25/13 mm -Drawing with the pictures -Total length: 200 mm -Total height: 188 mm -Weight: 6 kg

Gear motor, electric motor -Speed: 30.5 rpm -Power: 0.55 kW -Brake: 440 V -Construction: B5 -Shaft diameter: Ø 30 mm -Protection class: IP 65 -Number: 1x motors available -Price: per piece -Dimensions: 605/250/H215 mm -Weight: 36 kg

Electronically controlled, programmable roller feed for advancing and precise positioning of strip material SIEMENS® PLC – Control Largest sheet strip width 200 mm (optionally up to 800 mm) Sheet thickness range 0.8 to 3 mm Steel sheet 400 N/mm² - (optional thicker sheets on request) Rollers Ø 95 mm Maximum practical feed rate in operation with eccentric presses: 120 strokes per minute with a maximum feed length of 80 mm per stroke

Gear motor, electric motor -Speed: 68 rpm -Power: 0.55 kW -Construction: B5 angle -Diameter shaft: Ø 25 mm -Protection class: IP 54 -Number: 1x motors available -Price: per piece -Dimensions: 400/180/H200 mm -Weight: 21 kg

For sale : 200/250 ml Square conversion kit for A3flex machine. I send photos by email.

Stock# U2412-3 Unused progressing cavity pump by Allweiler type AEB 1E 200. Pump is driven via Nord gearbox and el motor 2.2 kW, 1445 rpm, 230/400 V, 50 hz. Pump works with rotation up to 150 rpm. Working output depends on product and rotation and can reach from 5 l/min, up to 500 l/min. At current rotation on gearbox pump can reach 60 l/min / 3600 l/h. Mounted on carbon steel base.

Machine vice, vice, drill press vice -Jaw width: 155 mm -Back height: 80 mm Clamping depth: max. 200 mm -Dimensions: mm -Weight: 35 kg

Wire brush round, round grinding brush, braid round brush, grinding wheel, cup wheel -Inside: Ø 32 mm -Outer: Ø 200 mm -Width: 25 mm -Number: 3x discs available -Price: per piece -Weight: 1 kg