132,114 used machines on RESALE, but how to find them? Machine Search
Screw Compressor WORTHINGTON - CREYSSENSAC Type Rollair 40 -- RLR 40BM6Fabr. No. 6240330200 built in 2003Volume flow rate 4.6 m3/min. Pressure capacity 10 barMotor power main motor 30 kWNe-connection 400 Volt, 50 HzConnection thread 1 1/2 inch- 36004 Switch-on hours read- 19256 load hours read- SoundproofedSpace requirement L x W x H 1850 x 1050 x 1760 mmWeight 910 kggood condition; used
Battery interchangeable rack, transport rack, storage rack for forklift batteryChanging table, battery pallet, battery swapping system, battery swap trolleyManufacturer: WELUX 2.5Type: WS2-RR-2-300Load capacity: 2x 500 kg per compartment = 1000 kgSlide-in dimensions per compartment W x D = 300 x 920 mmSlide-in dimensions without centre bar W x D = 655 x 920 mmAdjustment height: 80 to 200 mm - centre bar can be dismantled - also suitable for sheet material - 16 pieces of galvanised steel castors 50 mm - 4 pieces of fixed castors 100 mm, 2 pieces rotatable with fixed castors
Universal temperature control unit WEINREICH type WTD 4Temperature control unit with electric heating and connections for external coolingFabr. No.: 11932217 year of construction 1993Temperature max. 140CBorcing pressure max. 6 barPump capacity 30 l/min. Tank volume 4 litresHeating capacity 4 kWeergisation capacity heat exchanger 15 kWCotor capacity of the pump 0.37 kWUmrune water supply + return G 3/8Cooling water flow + return G 3/8Total capacity 4.4 kWNe-connection 380 volts, 50 Hz, CEE plug-in temperature control medium water
Hydr. Scissor lift table WEIDMANN type E5/13-1Fabr. No. 30403339 Year of construction 1982 / 2007Load capacity 500 kgPlatform size 2000 x 1200 mmStroke max. 1280 mmOverall height - table bottom 290 mmOverall height - table top max. 1570 mmTable height with safety support 1430 mmLifting speed 1280 mm in 25 sec. Lowering speed 1280 mm in approx. 0 to 15 sec. Hydraulic operating pressure approx. 130 barEngine power 1.5 kWNex connection 400 volts, 50 Hz.- Rotary switch switch on the hydraulic power unit for up and down lowering speed
Radial drilling machine WEBO type R4bRFabr. No. 15 / E195 Year of construction approx. 1965Drilling capacity 40 mmThroat: approx. 1250 mmSpindle holder: MK 4Spindle speed: 30 - 1325 rpm. 9 stepsFeed from 0.12 - 2 mm/rev. 9 steps; used
L + Z Lathe WEWAG Model 250 / 1500Fabr. No. 20953 Year of construction approx. 1975Center width 1500 mmNominal turning diameter over bed 500 mmTurning diameter over bed max. 510 mmCenter height over bed 255 mmTurning diameter over support 300 mmCenter height over support 150 mmSpindle bore 56 mmSpindle speed 18 - 1800 rpm. 24 stepsRotary chuck mount short taper DIN 55022Tailstock inner taper MK 5Drive power 4 kW and 6.7 kW pole-switchable- 3-jaw lathe chuck BISON, 250 mm-
Hydr. Hacksaw, hacksaw, lifting saw KASTO type PSB WBS 210 / 230Masch. No. 115 106 1212 / 72783 Year of construction 1986Sawing area - Round 250 mmSawing area - Square 225 x 225 mmSawing area - Rectangle 260 x 100 mmCutting speed 11 -13 - 17 - 22 - 26 - 34 m/min. Saw blade length 400 mmMotor power 1.4 and 1.8 kW pole-switchableMains connection 380 volts, 50 Hz- only for 90 cuts, no mitre adjustment- Saw motor with 2 speeds and 3 V-belt steps- Hydraulic saw bar feed- hydraulic
E-chain hoist, electric chain hoist, crane KITO type WLL 240 ManuliftManufacturer: KITO Yamanashi JapanCode No. EDC 24SD Series No. 035884 Year of construction 2018Load capacity 240 kgHook travel 2 metersDistance suspension to load hook 850 mmLifting speed 3 to 12.9 m/min. mains connection 230 volts, 50 Hz- cylinder handle control with potentiometer for speed adjustment- safety- stroke limit switch- emergency stopweight 18 kgvery good condition; used
CNC Lathe - twin turret - subspindle Y axis NAKAMURA WTS150, CNC Fanuc, Series 16i-T, Spindle - Subspindle, 3x turrets, live tools + 2 Y axis (milling), 2x C-axis, Conveyor, LNS bar loader (short bars) Mimu machine tools Italy
A Wieland extraction system is available. Engine speed: 2930rpm, power: 18.5kW, weight: approx. 1200kg. Documentation available. On-site inspection is possible.
Weinig Quatromat 23 Moulder Specifications: Brand: Weinig Type: Q23P (profileerautomaat) Year of Make: 2003 M-No.: 99567 Feed table: 2000 mm Dressing table adjustment range: 10 mm Joining ruler adjustment range: 10 mm Planing width: 13 - 230 mm Planing thickness: 6 - 120 mm Thickness adjustment: Manuel with Siko counter Width adjustment: Manuel with Siko counter Head dimension: Min. 613mm, up to max. 120230mm Knife shafts: Bottom: ø125 mm Right & Left: ø125-200mm Top: ø125-200 mm Adjustment range dressing shaft: 5 mm Spindle adjustment range axial: 30 mm Min. Product Length: Short Workpiece Length Equipment Central Control: Relay Control Lubrication: Spindle arrangement: Bottom 4.0 KW Right + Left Spindle 5.5 kW Above 4.0 kW Speed: 6,000 rpm Feed: 8 m/min Stepless -1.5 kW Steel and rubber rollers. 1 feed roller electro-pneumatically cycled ...
Z455 Workpiece Conveyor Belt of CNC Automatic Lathe WEBO Tape width 80mmx tape length ,450mm fabric tape is missing Drive 380 V on the motor with toggle switch off and on T-slot on both sides Dimensions L1550 x W300 x H150mm Weight approx. 20kg Price EXW excl. VAT Prior sale and errors excepted Euro 600.--
turning diameter: 720 mm turning length: 3000 mm centre height: 360 mm spindle bore: 106 mm turning speed range: 1 - 1800 U/min tailstock quill taper MT: 6 workpiece weight max.: 3800 kg total power requirement: 36 kW weight of the machine ca.: 6100 kg dimensions of the machine ca.: 4800 x 2450 x 2000 mm CNC lathe - cycle controlled The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
1 used WEINMANN Gebertisch, built in 2022, as good as new, For now.. without control, as this remains in the overall production control. Control is about 6000 euros new from Weinmann. Size 12 x 3 m - Model BuildteQ A 570.. Sale as seen from site without warranty, dismantling is helped with overhead crane and forklift free of charge without warranty.
Plastic dryer - Wittmann Drymax E30-70-M / Very good technical condition Year of Make: 2015 Location: Lodz, Poland Description: Dryer with 2 molecular sieves, 1-silo Silo capacities: 150 kg Sieves work alternately, during the drying process, one sieve works and the second sieve regenerates Hermetically insulated silo Dryer with Wittmann suction conveyor Price: On request
Plastic Dryer - Wittmann Drymax D60-150-M (2 pcs.) Year of Make: 2011 Location: Lodz, Poland Description: Dryer with 2 molecular sieves, 1-silo Silo capacities: 150 l Sieves work alternately, during the drying process, one sieve works and the second sieve regenerates Hermetically insulated silo Dryer with Wittmann Feedmax S3-40 suction conveyor Price: On request
Conveyor - Wittmann Feedmax S3-NET / New, unused (6 pcs.) Year of manufacture: 2023 Location: Lodz, Poland Description: Suction conveyor with a hose and suction probes The conveyor has its own control system. On the control system, you can set the proportions in which the raw material is to be transported It is possible to buy a plastic container as well as a proportional valve for transporting 2 raw materials, e.g. regrind and original Price: On request
Conveyor - Wave Year of construction: Location: Lodz, Poland Description: Suction conveyor with a hose and suction probes The conveyor has its own control system. On the control system, you can set the proportions in which the raw material is to be transported It is possible to buy a plastic container as well as a proportional valve for transporting 2 raw materials, e.g. regrind and original Price: On request
Number of axis: 3 X: 1500 mm Y: 2600 mm Z: 4000 mm + C axis pneumatic Reach: 4000 mm Payload: 41 kg
Parallel Lathe WABECO D6000E Between points: 600 mm Maxi Ø on bench: 270 mm Maxi Ø over saddle: 170 mm Spindle speed: from 45 to 2300 RPM Multifix turret type A Concentric 3-jaws chuck Ø 100 mm (NEW) Year of construction: 1998 (machine very little used) Spindle speed by variator Tailstock CM2 Scale 2 axes EAE type Mikronel 220 L Supplied with one clamp tie rod Accessories: 5 tool holders + different thread wheels Voltage: 220 V mono Dimensions (L x W x H): 1500 x 900 x 1700 mm Weight: approx 200 kg
Inv. Num. : 8559 Type: WDR 1000 CNC Producer: Wagner Created: 2011 Parameters: Control system: Siemens 840D Maximum turning length: 5000 mm Maximum turning diameter over bed: 750 mm Maximum turning diameter over support: 666 mm
Travel X/Y/Z: 495mm/205mm/355mm, table clamping surface: 1060mm, spindle bore: 46mm, speed: 2240rpm, machine dimensions X/Y/Z: approx. 4300mm/2100mm/1750mm, weight: approx. 1900kg. Only with counter bearing for arbor mandrels, key, and hobbing arbors. The machine shows bearing noise and play on the X-axis. Documentation available. An on-site inspection is possible.
pressure: 25 t throat: 200 mm stroke: mm pressure: 25 t no. of strokes: 140 Hub/min window in frame: 240 mm adjustment of stroke: 8...80 mm ram - range of adjustment: 50 mm surface of ram: 355 x 220 mm table-size: 560 x 400 mm hole in table: 160 mm total power requirement: 3 kW weight of the machine ca.: 2,23 t dimensions of the machine ca.: m - distance table slide: 250 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Beck Wand 1000/2000 Extraction Wall Extraction wall Type: Beck Wand 1000/2000 Extraction wall made of sheet steel, with 5 suction slots made of perforated sheet metal evenly distributed. For connection to a central extraction system via a suction nozzle at the top center of the extraction wall. Cleaning opening can be unscrewed at the bottom of the front of the wall. Uses: Extraction of process air during grinding and milling Extraction of gases and light dust Extraction of powder mix or other stationary dust-forming processes Width: 1000 mm Height: 2000 mm + 100 mm nozzle Depth: 300 mm Suction nozzle: NW 250 top center Recommended extraction capacity: 3000 m3/h Paintwork: RAL 5018, RAL 7032 Weight: approx. 75 kg Manufacturer's price: 2970,-€ More items - new and used - can be found in our shop! International shipping costs on request!
Lead and pull spindle lathe WEIPERT Year of Make: 1956 Spindle bore: 90 mm Center width: 3000 mm Circulation Ø over bed : 800 mm Circulation 0 over slide: 610 mm Circulation 0 in offset: 1120 mm Speed range: 7.5 – 475 rpm With the following accessories: Multifix tool holder with 11 inserts Coolant Setup Three-jaw chuck 0315 mm Three-jaw chuck 0 400 mm Three-jaw chuck 0 500 mm Face Plate 0 400 mm Face Plate 0 800 mm Face Plate 0 1000 mm Running Lynette Various turning tools (30 pcs. indexable insert tools) 2 moving centering tips 1 drill chuck Operating instructions
Approx. 170 tool holders, some with tools
measuring range X-axis: 300 mm measuring range Y-axis: 290 mm measuring range Z-axis: 650 mm tool diameter: SK 50 mm Number of revolutions: 30 U/min max. workpiecediameter: 300 mm max. workpiece length: 500 mm max. workpiece weight: 40 kg accuracy +/-: 0,002 mm feeds:: Working speed: X/Y/Z: 80 mm/s dimensions of the machine ca.: 2,5 x 2,0 x 2,5 m weight of the machine ca.: 1,2 t total power requirement: 1 kVA Documents: Tool-Presetter WALTER - Heli Toolcheck The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
WMW HECKERT FU450R-51 universal milling machine was built in 2009 in Belarus by Gomel Machine Tool Plant S.M. Kirov.. This extremely versatile, functional and reliable machine is designed for precision machining of workpieces with a maximum weight of 1500 kg. The machining process is performed by a powerful spindle on a large work table. T-slots in the table allow for quick installation of additional tooling such as a vice. The precision and repeatability of the manufactured parts, in turn, is maximised by the design made of the highest quality cast iron, which maintains excellent stability during even the most intensive challenges. All this makes the offered FU450R conventional milling machine an excellent choice for both unit and series production. The WMW HECKERT vertical milling machine weighs 4300 kg. Technical specifications of the WMW HECKERT FU450R-51 milling machine - number ...
Manufacturer: WEEKE Model: OPTIMAT BHT 500 Year of Manufacture: 2009 Technical Specifications: - Voltage: 400 V - Frequency: 50/60 Hz - Phases: 3 + N (three-phase with neutral) - Power Consumption: 45 kW - Current Rating: 100 A - Control Voltage: 24 V Find more here - / Contact us at -
max. wheel diameter: 780 mm gear width: 130 mm max. module: 8 / 10 table diameter: 510 mm table bore diameter: 160 mm number of strokes (double strokes): 30 - 1500 DH/min Control: Siemens Sinumerik 3 distance table - lower edge of ram: 650 mm table-size: 500 mm total power requirement: 36 kVA weight of the machine ca.: 8,5 t dimensions of the machine ca.: 4,9 x 3,65 x 3,8 m The machine is suitable for: - Internal and external gear teeth in small quantities - Internal gear teeth in blind holes (non-through holes) - External gear teeth without run-out, as hobbing would not be possible Examples of components are: Internal gear rings for planetary gears, drive shafts, clutch hubs... - Siemens Sinumerik 3 CNC control - Chip conveyor Machine was only used sporadically The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Table clamping surface: 600 x 300 mm Coordinate travel: X 350 Y 250 mm W-axis adjustment range (motor): 200 mm servo-controlled EDM axis Z: 340 mm Holes with electrodes from Ø 0.2 to 4 mm Max. workpiece weight: 300 kg Connected load: 3.5 kVA Machine weight: 700 kg
Travel X/Y/Z: 800mm/2000mm/700mm, max. length measurement error: 2.5 + L/350, max. single-point error: 2.5, control: Pantec Eagle Pro/3. Includes test head PH10M Plus, PHC-2, sensor TP200, 20-piece probe set, calibration sphere, industrial PC, measuring software Inca 3D Premium with STEP and factory calibration. The machine can be equipped with additional options. Documentation available. An on-site inspection is possible.
Travel X/Y/Z: 800mm/1000mm/700mm, max. length measurement error: 2.5 + L/350, max. single-point error: 2.5, control: Pantec Eagle Pro/3. Includes test head PH10M Plus, PHC-2, sensor TP200, 20-piece probe set, calibration sphere, industrial PC, measuring software Inca 3D Premium with STEP and factory calibration. The machine can be equipped with additional options. Documentation available. An on-site inspection is possible.
Travel X/Y/Z: 600mm/750mm/500mm, max. length measurement error: 3 + L/350, max. single-point error: 3, control: Pantec Eagle Pro/3. Includes test head PH10M Plus, PHC-2, sensor TP200, 20-piece probe set, calibration sphere, industrial PC, measuring software Inca 3D Premium with STEP and factory calibration. The machine can be equipped with additional options. Documentation available. An on-site inspection is possible.
Travel X/Y/Z: 500mm/600mm/400mm, max. length measurement error: 2.9 + L/350, max. single-point error: 2.9, control: Pantec Eagle Pro/3. Includes test head PH10M Plus, PHC-2, sensor TP200, 20-piece probe set, calibration sphere, industrial PC, measuring software Inca 3D Premium with STEP and factory calibration. The machine can be equipped with additional options. Documentation available. An on-site inspection is possible.
Production Year 2015, start use in end of 2015. Used for two Year. Was used with 75kW electric motor. Now it is without motor. Can be used with some diesel motor. Have spare knives. Can input up to 42cm diameter log
Grinder with mixer Manufacturer: Kramer Grebe Wetter Model: Grinder 130mm Made of stainless steel Lowest noise level Easy cleaning Hopper volume: 245 liters Voltage: 400V 50Hz Weight: 850kg
Travel X/Y/Z: 4000mm/1800mm/2500mm, max. length measurement error: 55 + L/35, max. single-point error: 35, control: WPC 2040. Includes test head PH10M Plus, PHC10-3, sensor TP20, 20-piece probe set, calibration sphere, industrial PC, measuring software Inca 3D Premium with STEP and factory calibration. The machine can be equipped with additional options. Documentation available. An on-site inspection is possible.
maximum number of results exceeded
please refine your search
