w 100a used for sale

WIWA High Pressure Pump 235.42R / 38042, YOC 2000 With high flow rate, ideal as a feed pump for airless sprayers (united for medium and low viscosity coating materials) Material guide in stainless steel (suitable for water-based paints) Gear ratio: 42:1 Air inlet pressure max. 8 bar Flow rate per double stroke 235 cm3 Flow rate max. 38 l/min. Maximum permissible operating pressure 335 bar Piston diameter of the air motor 230 mm Piston stroke of the air motor 120 mm

weight max.: 5 t workpiece diameter: 150 - 1800 mm Turning speed: 70 - 1200 mm/min roll diameter: 250 mm total power requirement: 1 kW weight of the machine ca.: 0,5 t dimensions of the machine ca.: 1,8 x 1,5 x 1,0 m • demonstration unit • unused vessel turning unit, • with rubberised rolls, manual adjustable roller-spacing, • one device with twin drive with adjustable rotational speed. • with CE marking The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

weight max.: 3 t workpiece diameter: 120 - 1500 mm Turning speed: 0,6 - 1000 mm/min roll diameter: 250 mm total power requirement: 0,5 kW weight of the machine ca.: 0,6 t dimensions of the machine ca.: 1,4 x 1,5 x 1,0 m • demonstration unit • unused vessel turning unit, • with rubberised rolls, manual adjustable roller-spacing, • one device with twin drive with adjustable rotational speed. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

chamber volume: 170 liter useable volume: -- liter friction: -- motor drive power: 800 kW Condition: used - Specification: internal mixer used as additional option: Rubicon batch-off plant - capacity approx.: 170 litres - rotor model: tangential design - drive controller: Allen Breadley - Control: Mitsubishi - Motor speed: 1,000 rpm - Gearbox: Panamax 9000 make Sumitomo - Rotor speed: 5.6 - 55.6 rpm - Chamber hardness: 45 -50 HRC - Motor: 800 kW - 1000 rpm - 380 V, 50 Hz - Moror make: Teco - Output: 27 tons/day - Cycle time approx.: 4 - 8 min - Height approx.: 7,500 mm - Weight approx.: 35,000 kg, incl. gearbox and motor Available as an option: - Batch-off system Make: Rubikon / Mattech - Cooling bars max.: 300 mm / 2x 80 mm The data for this ad was created with ModulMWS - the software solution  ...

WEBER COOLING BASE TWO Vacuum cooling system Cooling capacity: 2 IP or 2 EUR Products to be cooled: leafy vegetables/fruits up to 1000 kg Cooling temperature: from 20-30 degrees C to 3-5 degrees C Control: PLC Unitronics V1040, Weber 2022 software Vacuum pump: 1 x Busch RA R5 0305D ( 300 m3 / h ) Chiller: Aermec ANL 202 Compressor: Metabo Basic 250-24W OF

Counter support, counter bearing, bearing block, pillow block, bearing for milling machine, milling machine horizontal -Manufacturer: WMW, counter bearing from milling machine FW 400 x 1600 -Dimensions: see drawing in the photos -Transport dimensions: 1505/400/H345 mm -Weight: 370 kg

Device characteristics: Number of bars: 48 per minute. Hopper capacity: 7 litres. Weight: from 10 to 80 g ( depending on the stamp ). Dimensions ( L x W x H ): 500 x 400 x 650 mm. Total weight: 27 kg.

Heavy duty castors, heavy duty wheel, tire, forklift drive wheel -Manufacturer: Wicke- Elastic heavy duty bike -Wheel size: Ø 270/105-225 mm -Hole circle: Ø 188/9 mm -Price: per piece -Number: 1 piece -Weight: 8.9 kg/piece

Safety relay, relay, heating current monitoring, contactor, semiconductor contactor, contactor -Type: SVS11/R-2-24 V -Allow. Operating temp.: -20/+50 °C -Response time: 50 ms -Obstacle size: Ø 50 mm -Fuse: M400 mA -Weight: 2.1 kg

First installation year 2010 - Bar capacity 52 mm - The machine has always worked with oil - Equipped with Lns Sprint S2 barfeed, front magazine type, and a lot of accessories (for both lathe / barfeed) - Fanuc 31i-A Control.

Manometer, test manometer, pressure measuring device with Bourdon tube, pressure-temperature measurement technology -Manufacturer: Wika, pressure gauge type 233.50.063 16 bar -Art.-No.: 12064394 -Screw connection: G1/4B -Dimension box: 90/100/H70 mm -Weight: 0.3 kg

Cam switches, circuit breakers, motor protection switches, step switches, rotary switches -Type: WAA477/100 VZ -Voltage: AC-3 kW 3 ph 380 V/440 V 125 A -Dimensions: 330/95/H130 mm -Weight 2.3 kg

-3 pieces available in stock -for 10 sheets 60x40cm -with Wiesheu Comfort control -Power 19 kW -400 V 3/N/PE -Rated current 27.5 A -Supports distances 8cm -Year of construction: 2014 Dimensions: Width: 93cm Depth without hood: 100cm Depth with hood: 115cm Height: 217cm

Since we have focused our -fischer organics- laboratory service more on peptides / HRMS, we would like to hand over our SFC. The system has the complete equipment, The original price in 2012 was over 250,000 euros net! - Mass detector QDa - Backing pump RE6 - Acquity PDA detector - Acquity Pillar Manager - Acquity Binary Pump 1000bar - Acquity Autosampler - Isocratic UPLC pump - Convergence Manager

Electromagnet with large depth action for extracting ferrous parts from a material stream, oil-cooled design. Including control cabinet with 22 V DC power supply (type: 312-220/20, for connection to 400 V / 50-60 Hz) and overhead duo-rail installation (ca. 4.5 m long x 2.5 m high) for moving the magnet. By switching off the magnet above the drop point attracted ferrous parts are removed.

Transformer, transformer, converter, three-phase autotransformer -2 pieces: three-phase transformers DTST 7.5 -with: additional electronic modules -Primary: 400 V -Power: 5.5 kVA each -Dimensions: total 200/430/H740 mm -Total weight: 164 kg

Machine Details Stock-No. 1105-03837 Type of machine Machining Center - Vertical Make WILLEMIN MACODEL Type 408 S Year of manufacture 2000 Type of control CNC Storage location HAGUENAU FRANCE Country of origin SUISSE Delivery time immediately Freight basis ex Site Technical details x-travel 250 mm Y-Travel 200 mm Z-Travel 300 mm control FANUC 16 I MB A-Axis -30° - +100° C-Axis 360° table load 200 kg Rapid traverse 20000 m/min turning speeds 35 - 30,000 rpm tool taper HSK E40 power capacity - milling spindle 15/10 kW Tool piece magazine with 92pos. tool diameter 80 mm Tool-Dia with Free Toolbox 95 mm tool length 200 mm tool weight 8 kg Tool Changing Time 3.6 sec total power requirement 35 kW weight of the machine approx. 2.5 t dimensions of the machine approx. 2.0 x 2.1 x 2.65 m Accessories Chip conveyor Coolant system electr. Hand Wheel Coolant ...

MIG/MAG hose package -MIG/MAG hose package: water-cooled -Length: 3,2 m -Weight: 3,0 kg

amount: 1 STK The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Max diam 250 , max lenght 2000, 3 x heads , change gears

MIG/MAG hose package, MIG/MAG welding torch -MIG/MAG hose package: water-cooled -Number: 2x hose package available -Price: per piece -Length: 6.3 m -Weight: 5.4 kg

heavy-duty castors, heavy-duty wheels, tires, forklift drive wheels -Manufacturer: Wicke- Topthane heavy-duty wheel -Wheel size: Ø 230 x 90 mm -Bolt circle: Ø 95/13 mm -Price: per piece -Quantity: 2 pieces -Weight: 7.5 kg/piece

Face plate, face plate chuck, four-jaw chuck, facing chuck -Transfer: in the current condition as seen -Face plate: without jaws -Chuck size: Ø 770 mm -Shot: short taper 11 -Hole circle: Ø 235 mm -Through hole: Ø 120 mm -Groove width: 24 mm -Weight: 234 kg

Control cabinet and distribution board, busbars, busbar supports, busbar adapters -Wöhner item no.: 01 508 -Rated current: 690 V/630 A -Quantity: 16 pieces available -Price: per piece -Minimum order: 3 pieces -Dimensions: 190/25/H50 mm -Weight: 0.2 kg/piece

Wartsila L32 cylinder heads Brand new condition With BV class certificate 8 Pcs available In our stock in Istanbul Turkey

Converters for bottle vibrators, vibrating bottles, internal vibrators, concrete vibrators -Manufacturer: Wacker -Handover: as is as seen -Transport frame wheels defective, see picture -Motor: 2.8 kW -Vibrating bottle: length 360 mm -Hose length: 5 m -Dimensions: 1150/520/H690 mm -Weight: 116 kg

Refer to code 1004 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

number: 10 Stk. clamping range: 15 - 50 mm : 28 mm weight: 10 kg dimensions: 0,3 x 0,3 x 0,2 m Basic set 4 / 53 pieces for table top thickness 15mm and 25mm 6 pcs screw clamps 14 pcs. quick clamping bolts 2 pcs. universal stop 100mm 6 pcs. universal stop 150mm 6 pcs. universal stop 225mm 2 pcs. universal stop 300mm 6 stop and clamping angles 175mm 4 stop and clamping angles 275mm 2 pcs. prisms 60mm 1 piece torch holder 1 pc. Eccentric stop 100mm diameter 1 piece perforated brush 30mm 2 pieces separating lotion 500ml, on a natural, biological basis 2 pcs. Welding table cleaner 500ml, on a natural, biological basis The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Central lubrication, oil circulation system, progressive pump, central lubrication unit -Drive motor: Siemens -Pump: 440 V 0.105 kW -Number: 1 x pumps available -Price: per piece -Dimensions: 290/180/H340 mm -Weight: 8.7 kg

Hydraulic pump, oil pump, gear pump -Max.: 600 rpm -Working pressure: 2 bar -Output: 3 l/min -Number: 1x pumps available -Price: per piece -Dimensions: 95/100/H90 mm -Weight: 2.3 kg

Refer to code 1006 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Tank-& Umweltschutz Wozniack Fachbetrieb nach Wasserhaushaltsgesetz Delivery time immediately Dear Sir or Madam, we offer a 10,000 liter double-walled storage tank for the storage of diesel. Heating oil or other hazardous substances as follows. Nominal capacity 10 cbm according to EN 12285-2 standard Piece 1. Material steel in steel, material S235JRG2 Documents Manufacturer's certificate/test certificate according to EN 12285-2 standard and type plate Piece. 1 dipstick Piece. 1 vent nozzle Piece. 1 filler neck Piece. 1 new limit value transmitter Piece. 1 new leak detector with filled leakage liquid Piece. 1 ladder Piece. 1 removal sleeve Form. cylindrical storage tank with feet/bracket Container dimensions length approx. 5,300 mm Diameter approx. 1,600 mm Weight approx. 1.800 kg Storage above ground Top on offer . Liquid ferti ...

Gear motor, electric motor, three-phase motor -Speed: 22 rpm -Power: 0.18 kW -Shaft: Ø 20 x 40 mm -Protection class: IP54 -Construction: B5 angle -Dimensions: 325/240/H155 mm -Weight: 9.8 kg

Refer to code 1013 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

Tank-& Umweltschutz Wozniack Fachbetrieb nach Wasserhaushaltsgesetz Delivery time immediately Dear Sir or Madam, we offer a 50,000 liter double-walled storage tank for the storage of diesel. Heating oil or other hazardous substances as follows. Nominal capacity 50 cbm Piece 1 Bring in colour wishes. Material steel in steel, material S235JRG2 Documents Manufacturer's certificate/test certificate according to EN 12285-2 standard and type plate Piece. 1 dipstick Piece. 1 vent nozzle Piece. 1 filler neck Piece. 1 new limit value transmitter Piece. 1 new leak detector with filled leakage liquid Piece. 1 ladder Piece. 1 removal sleeve Form. cylindrical storage tank with feet/bracket Container dimensions length approx. 10900 mm Diameter approx. 2,500 mm Weight approx. 9000 kg Storage above ground Top on offer . Liquid fertilizer -  ...

Refer to code 1001 in your request More information on our web page G3 Mixing Technologies - G3 STOCK or LinkedIn G3 STOCK Used machine, possibility to be purchased "as is" without warranty, or completely rebuilt and guaranteed as new machine.

in very good working condition

In-store oven WIesheu Type: Dibas Duo Dibas 64 blue S + Dibas 64 blue L 10+5 editions for 60×40 cm sheets digital control Self-cleaning program  Door with internal sliding mobile on wheels tested & cleaned, very good condition Specifications: Year of construction: 12/2017 (2018 Model) 400 V – 50 Hz Dimensions: Height: 215 cm Width: 95 cm Depth: 100 cm

CATALOG NO. 6904 TECHNICAL DATA - max width of the workpiece 230mm - max height of the workpiece 130mm 6 spindles: 1) horizontal bottom 230mm 5.5kW 2) vertical right 130mm 3) vertical left 130mm (2nd and 3rd spindle) 7.5kW 4) horizontal top 230mm 5.5kW 5) horizontal bottom 230mm 5.5kW 6) universal 230mm, 360° adjustable 5.5kW - all spindles adjustable up / down, right / left - spindle 1,2,3,4,5 equipped with an electric brake - spindle diameter 40mm - 5 introductory, toothed, pulling rollers from above - from above, 4 rollers, pulling, rubber, smooth, including 2 double - from the bottom, a rubber roller, pulling - feed on cardan shafts - rollers pressed pneumatically - smooth adjustment of the feed speed - feed motor 4kW - working pressure 6-10 bar - electric setting of planing thickness - motor lifting the body of about 0.55 kW - central lubrication of the co ...

Tapping chucks, thread chucks, tapping chucks, milling tools, tapping attachments -Manufacturer: WMW, thread cutting chuck mount MK3 -Types: GB3 -Dimension: Ø 80 x 270 mm -Weight: 3.7 kg

Qty. 1 Second-hand wall paper production line – already dismantled & in warehouse Mfc.: Shin Shang Built: 1998 New electrical incl. cables in 2019 Production stopped in 2/2023 In line system Printing width: 850 mm 6 colors printing station Hot embossing system PVC coating system Six colors high speed paper roll CI flexo printing machine Automatic high speed flexo printing machine High speed CI type Central Drum 6 Colors Flexographic Printing Machine for paper OPP/ BOPP/ PP plastic film rotogravure printing machine

Pneumatic cylinder, air cylinder, pneumatic stamp, compact cylinder -Manufacturer: Wabco Westinghouse, compact cylinders -Stroke travel: 900 mm -Piston: Ø 80 mm -Piston rod: Ø 22 mm/M20x1.5 -Price: per piece -Quantity: 2 pieces -Dimensions: 1165/95/H95 mm -Weight: 15.2 kg/piece

Type / type: N 25 Year of make: 1977 Manufacturer / make: Weingarten Rated pressure: 25 t Number of strokes: 140 / min Radius slide center to frame: 200 mm Window in frame: 240 mm distance table slide: 250 mm Stroke adjustment / adjustment of stroke: 8 ... 80 mm Ram adjustability/adjustment of ram: 50 mm Ram size / surface of ram: 355 x 220 mm Table size / surface of bed: 560x 400 mm Hole in table: 160 mm Power of main motor:3 kW Weight / weight: 2,23 t

Batch / spiral kneader W&P, type: UC50 AC -overhauled- - including 2 tank cars - for 50 kg flour or 80 kg dough - for mischweizen and mixed rye dough - in bakery condition - very nice condition, immediately ready for use - Video with kneader in function on request Inspection and test run are of course possible at any time by arrangement. The machine has been tested and is ready for immediate use.

Gear motor Flender MBH 125CC-B 27.7/1 Bevel helical gear drive motor 11 kW at 1400 1/min. 230/400 V, 50 Hz, IP 55 were operated with frequency converters Matching Freqenzumrichter Walther Flender ZZ0103069.34003 Sinus Penta available A total of 15 traction motors and 12 drives ! available Very good condition, straight from production!

Removed in rotating condition due to re-engine Incl. propellor shaft flange and original oil pit

Bezel, steady rest, lynette -steady rest: from lathe WMW DLZ 800 -Max. Passage: Ø 260 mm -Tip height: 495 mm -Technical drawing: in the photos -Dimensions: 670/130 / H785 mm -Weight: 98 kg

Heavy duty castors, heavy duty wheel, tire, forklift drive wheel, swivel castor, track roller, pallet truck rollers -Manufacturer: Wicke- Topthane, roller -Wheel size: Ø 85 x 80 mm -Inside: Ø approx. 20.3 mm -Price per piece -Quantity: 1 piece -Weight: 1.4kg

WAGNER FCU 1600 universal milling machine manufactured in Germany in 1998 is designed for precision machining of workpieces in X,Y,Z axes with feeds of 1200 mm (X axis), 700 mm (Y axis) and 500 mm (Z axis). The machine characterised by its high reliability and efficiency performs the milling of workpieces on a large work table with a length of 1600 mm and a width of 500 mm using a precision spindle rotating at a maximum speed of 2050 rpm. The milling machine is also equipped with measuring rulers and digital readouts. The total weight of the machine is 4000 kg. Technical data of the WAGNER FCU 1600 milling machine - feed rates in the X/Y/Z axis: 1200/700/500 mm - feed speed in the X axis: 10-1000 mm/min - feed speed in the Y axis: 10-1000 mm/min - feed speed in the Z axis: 5-500 mm/min - rapid traverse in the X/Y/Z axis : 3000/3000/1500 mm/min - working table dimensions (L x W): ...

Specifications: Capacity: 60 t Passage between stand: 820 mm Working area, max.: 820 x 300 mm Piston stroke: 400 mm Flow speed: 6.1 mm/s Return speed: 10 mm/s Motor power: 3 kW Width: 1460 mm Depth: 850 mm Height: 2400 mm Weight, approx.: 700 kg Equipment: - Laterally movable cylinder - Spacious work area - Height-adjustable table - Torsion-resistant design made of welded steel -Manometer - Fine adjustment of pressure - Additional hand pump