137,143 used machines on RESALE, but how to find them? Machine Search
AGICOM Recycling Machines The used single-shaft shredder MR2260 is a powerful and energy-efficient shredder for the pre-shredding of cables, electronic waste, waste plastics, wood and much more... It has two stator knives for better product quality and higher hourly output. The shredder is equipped with an electronic control system. This monitors the hydraulic feed and the cutting shaft. As a result, the single-shaft shredder rarely has to reverse and retains its high throughput. Machine pre-equipped for cooling Control: Siemens Weight: approx. 1,800 kg Dimensions: approx. 1750 x 1300 x 1800 mm Capacity: up to 400 kg/hour (depending on material and perforated screen) Safety: retraction of the feed in the event of overload, reverse rotation of the rotor in the event of blockage Year of Make: 2019 Machine in good condition and ready for immediate use!
VEM motors GmbH75 kW400 V50 Hz144 A740 rpm968 Nm (20-50 Hz)S1/S9IP 55IM B3850 kg
Technical data cardboard shredder (2-shaft shredder): Manufacturer: Presto GmbH & Co. KG Type PZA Year of construction 2007 (52,998 h and 55,325 h) Throughput volume 130 m³/hour Speed 37/9 1/min. Motor power 7.5 / 2.2 kW Electrical connection 32 A Dimensions shredder inside 1,490 x 1,320 x 530 mm (L x W x H) Dimensions shredder external dimensions without hood 2,308 x 1,320 x 685 mm (L x W x H) Machine weight 0.45 t Use of the systems: The 2 pieces of cardboard shredders of the type PZA were used in a Dutch logistics center to pre-shred loose, erected cartons from the returns department and then press them into bales. The cartons were fed by hand onto the feed belt and were transported directly to the carton shredder with a sliding belt conveyor belt and torn. The pre-shredded cartons were then transported over hundreds of meters to the baler and pressed there. Sco ...
Fine shredder Doppstadt AK 565 EcoPower used Model: AK 565 EcoPower Year of manufacture: 05 / 2021 Build No.: 1550 Operating hours: approx. 2,700 hours Availability: by arrangement Equipment: - Mobile shredder, mounted on a central axle trailer chassis for 80 km/h according to StvZo with ABS - Total weight approx. 19,000 kg - Mercedes/MTU diesel engine 6R1300, 390 KW at 2,000 rpm, meets EUROMOT IV emission standard - Fuel system 600 liters - Load-dependent control of the material feed via scraper floor - Aggressive feed roller: length 1,690 mm, diameter 510 mm, with attached toothed elements - Four-row flail drum with 36 free-swinging cast steel flail holders and interchangeable DoppLock flail tips - Centrally located lubrication strips - Electric pump for operating the cylinder functions (raise/lower support leg, open/close rear basket, fold/unfold rear belt, ...
4 shaft shredder for crushing of thick-walled pipes. Supply via feeding shaft (not in scope of delivery, can be manufactured alternatively) Manufacturer Vecoplan Drive: Rotorshaft 1: 37 kW Rotorshaft 2-4: 30 kW (each)
Working Width: 800 mm Working Height: 300 mm Main Motor Power: 250 KW
Used shredders with gearbox not overhauled and also not repaired. Spare parts such as shafts, scrapers, knives, etc. also available as good as new.
Spare parts for raw material shredder Baader 152 (Raw Material Crusher Baader 152). Almost all spare parts are available in stock or at short notice. Alternatively, a new machine can be offered. Please contact us.
-PREPARATION AND PRODUCTION OF PRODUCTS -TRADE AND SALE OF PRODUCTS (NEW AND USED) -THE USE OF A COMPANY (JE AFTER AVAILABILITY)
XXL Large tire detwulster for OTR tires up to 1600 mm inner diameter! Mobile on rolling frame. Transport with unrolling tipper. Weight approx. 9500 kg, length approx. 6500 mm. Very good condition!
Small shredder for various tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). Rotor shaft with connectors for connecting a cooling device (e.g. when used for NYM old cables. The machine is 1 year old and little used from our demo machine inventory. The machine is offered with a one-year used machine warranty.
Styrofoam shredder MAXI XL 1400 x 560mm MAXI 1400 x 600mm JUMBO 1800 x 800mm Insertion opening: L x W Polystyrene shredder MAXI XL: 1400mm x 560mm Polystyrene shredder MAXI: 1400mm x 600mm Polystyrene shredder JUMBO : 800mm x 800mm Dimensions: L x W x H (dimensions without blower) Polystyrene shredder MAXI XL: 2.4m x 0.9m x 1.6m Polystyrene shredder MAXI: 1.9m x 0.8m x 1.8m Polystyrene shredder JUMBO: 2.4m x 1.1m x 1.8m Motor power/connection/power conveying fan: Pre-shredder / conveyor blower Polystyrene shredder MAXI XL: 5.5 kW | Blower 2.2 kW Polystyrene shredder MAXI: 6.2 kW (with built-in screw under the pre-crusher) | Blower 2.2 kW Polystyrene shredder JUMBO 11.2 kW (with built-in screw under the pre-crusher) Conveyor blower 5.5 kW Throughput (EPS) Polystyrene shredder MAXI XL: 8-10 m3/h Polystyrene shredder MAXI: 25-30 m3/h Styrofoam ...
NEW! flaker for frozen products (fish, meat, vegetables, etc...) electric power : 18,5 kW speed of the cutting drum : 112 rpm dimensions of the machine (l x w x h) : ± 2.950 x 1.600 x 1.780 mm product temperature : max. – 30°C opening/closing lid: pneumatic "Festo" 6 bar capacity : ± 7.000 kg/h for blocks of max. ± 810 x 650 x 350 mm number of knives: 7 pieces various cut sizes possible (1 set of high knives is included): • low knives : 3, 6, 9 mm • high knives : 14, 17, 20 mm discharging possible in Dolav boxes 3 x 400 V, 50Hz weight : 1.860 kg
NEW! flaker for frozen products (fish, meat, vegetables, etc...) electric power : 9,2 / 11,5 kW speed of the cutting drum : 1st speed - 70 rpm / 2nd speed - 140 rpm dimensions of the machine (l x w x h) : ± 2.350 x 1.140 x 1.410 mm product temperature : max. – 30°C opening/closing lid: pneumatic "Festo" 6 bar capacity : ± 4.000 kg/h for blocks of max. ± 420 X 650 X 250 mm number of knives: 4 pieces various cut sizes possible (1 set of high knives is included): • low knives : 3, 6, 9 mm • high knives : 14, 17, 20 mm discharging possible in 200L eurobins 3 x 400 V, 50Hz weight : 980 kg
NEW! industrial shredder for pulled meat suitable for beef, pork, lamb, chicken,… content hopper : ± 35L electrical power : 1,47 kW capacity : ± 300-500 kg / h (depending on the degree of the cooking) possibility to place a 200 L eurobin at the bottom of the machine, so the product falls in it.
Used shredder In good condition this shredder was used inside the dutch greenhouses for taking out the final plants of tomato's, peppers etc Available directly.
Weima WL 4 Hackers Weima Single-shaft Shredder NEW Funnel opening with logspacer 600x1050mm Funnel content 0.6m/3 Working width of the rotor 600mm Diameter of rotor 252mm Drive power 18.5 kW Rotor speed 80-120 rpm Knife number 28 pieces Type & size of knives concave / 40 x 40 mm Sieblochung 10 - 100 mm Painting WEIMA Standard RAL 2002 / 7016 Connection value 400 V +/- 5% / 50 Hz Weight approx. 1,300 kg 2nd knife row
Shredder, rotor shears, plastic shredder, garbage shredder, two-shaft shredder, two-shaft shredder, used shredder 13 knives each approx. 300 x 36 mm each shaft is driven separately Insertion approx. 1450 x 1000 mm Platform height: approx. 1000 mm Drive 11 kW and 5.5 kW, 380 V Dimensions: approx. 3500 x 2000 x 3500 mm For crushing plastic, paper, cardboard, files, canisters, cans, floor coverings and the like.
Small shredder for a wide range of tasks such as old cables, plastics wood, etc. With hydraulic, electronically controlled feed. Drive 18.5 + 2.2 kW (rotor + feed). The machine was overhauled by the manufacturer ISVE in September 2020 and supplemented with an electronics for networking into a cable recycling line. A rotor cover for the optimized processing of old cables has also been added. Currently, the shredder has a 16 mm hole sieve but other hole diameters can also be added. With the 16 mm hole sieve, the shredder reaches about 250 kg/hour when processing mixing cables.
Construction debris / concrete shafts, suitable for Arjes Impactor 250 with quick-release cassette and dust-tight bearing lid - ready for installation - incl. transport frame ! We are happy to take care of the transport for you and build a professional !
Used shredder In good condition this shredder was used inside the dutch greenhouses for taking out the final plants of tomato's, peppers etc Available directly.
CATALOG NUMBER 6114 TECHNICAL DATA - 800x1000mm loading hopper inlet - rotor working width 800mm - pump motor 0.75kW - 15kW main engine - number of knives 21 pcs - dimensions of the knives 30x30mm - 0.8x10mm sieve - pressure drawer - electric reverse - 2 × 1.1kW discharge augers - dimensions length / width / height 2460x1800x2250mm - weight 1660 kg - German production - reverse - pressure drawer - unpainted - very good condition - used chipper Net price: 69 900 PLN Net price: 16069 euros depending on the price, 4.35 euros (Prices may vary for greater fluctuations)
Strand granulator type: ASG-4-63 without feed The GRANULATOR ASG 4-63 is only suitable for the cutting/granulating of semi-hard thermoplastics and is used in the regranulation /recycling of plastics on/on an extrusion line Up to 4 pieces of individual plastic strands with the Ø of 4 mm can be fed to the cutting rotor via a separate feeding unit, usually strip or roller puller. The part/granulate length is proportional to the feeding speed and can be adjusted by changing the rotor speed. Speed rotor max. 380 min-1 Ø Feed strands max. 4mm Cutting force : ~410 N EL connector: 400VDC 16A
Specifications Cutting width: 5.8 x 50 mm Year of construction: 2003 Productivity: approx. 120 sheets (DIN A4, 70g/m²) Price: on request Cutting speed: approx. 354 mm/s the security level: 3 Power supply: 400 V/4 kW
used shredder / shredder Manufacturer: ZENO Type: ZTLL 1600 x 1600 Year of construction: 2018 Operating hours: approx. 400 Specifications: Drive power: 2 x 55 kW Sieve: 35 mm hexagonal Screen design: solid screen basket, reinforced with ribs, including sieve quick-change device Counter knife: with cutting gap adjustment Hopper: 1,075 mm high, without lid with maintenance door and level sensor (Sonar Bero) Transmission: Compact gearbox with torque cut-off Filling opening: 1,600 x 1,600 mm Rotor speed: approx. 80 - 120 rpm Rotor aircraft: 600 mm Rotor design: 4 rows (76 pieces) positive inserts 60 x 60 mm on tool holders Rotor bearing: Standing bearing Machine floor and slide bottom: grooved Weight: approx. 13,400 kg Universally applicable shredder for a wide variety of materials The ZTLL shredder is the result of more than 35 years of kn ...
Cutting width: 5.8 mm Year of construction: 1993 Productivity: approx. 100 sheets (DIN A4, 70g/m²) Price: on request Cutting speed: 354 mm/s the safety standard DIN 66399: P2 Power supply: 400 V / 4 kW Machine is fully functional, after technical inspection. Price also includes the paint renovation. We have several channel balers and balers in our warehouse and we cordially invite you to contact us!
Specifications Industrial shredders IDEAL 4104 Shredder Cutting width: 6 mm Power supply: 400 V/ 4 kW the safety step P2 DIN66399-1 Year of construction: 1993 Productivity: ok. 70 sheets (DIN A4, 70g/m²) Machine is fully functional, after technical inspection. We have several channel balers and balers in our warehouse and we cordially invite you to contact us!
Specifications Cutting width: 3.8x50 mm Power supply: 400 V Year of construction: 1991 Price: on request the security level: P2
Specifications Cutting width: 12mm, 9mm, 6mm, 3mm Year of construction: 1988-1989 Productivity: approx. 70 sheets (DIN A4, 70g/m²) Price: on request Cutting speed: approx. 200 mm/s the security level: P1 - P2 Power supply: 380 V/2.2 kW Machine is fully functional, after technical inspection We have several channel balers and balers in our warehouse and we cordially invite you to contact us!
Specifications Shredder Cutting width: 5.8 x 40 mm Year of construction: 1992 Power supply: 400 V / 7.5 kW the safety level P4 DIN 66399-1 F2 DIN 66399-1 pts. 5.2 Baler Maximum pressure: 9 tons Year of construction: 1992 Pressing force: 36 tons/m² Channel cross-section: 500 x 500 mm Dimensions of the tailgate: 400 x 450 mm Power supply: 400 V/ 3.5 kW Bale binding: manual
For sale renewd shredder made by HOMBACK with 250kw. Used for shredding wood in long till chipwood.
Wood shredders, plastic shredders, garbage shredders, two-shaft shredders, shredders, shredders used Manufacturer: I.S.V.E. Srl Type: 80-80 D Year of construction: 2003 Insertion approx. 1500 x 900 mm Insertion height approx. 1600 mm Drive 2x 9 kW 380 V Dimensions: approx. 2400 x 1800 x 2400 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.
Catalog number 6726 TECHNICAL DATA - 280x300mm loading hopper inlet - outlet for shredded wood fi 310mm - rotor working width 340mm - 22kW main engine - number of knives 6 pcs - dimensions length / width / height 1300x1150x1680mm - weight 720 kg ADVANTAGES - very good condition - used chipper Net price: PLN 19900 Net price: EUR 4422 Net price, calculated at the rate of 4.50 PLN / EUR (with greater fluctuations in the rate, the price may change)
GRANULATOR TYPE PALLMANN PS-H 1000 x 1400, 132 kW very good condition incl. 3 sets of rotor knives and stator knives incl. 2 sets of screens, 5 and 8 mm IMMEDIATELY AVAILABLE AND READY FOR USE
SHREDDER KOMPTECH TERMINATOR 5000 E incl. control cabinet
Pre-shredder / shredder / chopper Fabr. Piranha for wood and plastic Motor 37 Kw Shaft length 600 mm with 3 x 5 Schneider knife with sieve 35 mm with control
used single-shaft shredder Manufacturer: LINDNER Type: VEGA 1100 L Year of construction: 2013 specifications: Filling volume: 1.7 m³ Working opening: 1,100 x 1,800 mm Rotor length: 1,090 mm Rotor flight circle: 434 mm Rotor speed: 100 rpm. Drive power: 45 kW Pneumatic pusher: 6 bar Weight: approx. 6,000 kg
used shredder Manufacturer: BOA Type: ALLIGATOR 550 - 100 Year of construction 2017 Specifications: Drive power: 55 kW Throughput: - 1,5 t/h for fine adjustment, and - up to 6.0 t/h with coarse setting Filler opening: 1,120 Rotor speed: 1,500 rpm Operating voltage: 400 V/50 Hz Insulation class: IP 55 Weight: approx. 5,200 kg
Cutting width: 4 x 60 mm Year of construction: 2015 Productivity: approx. 35-40 Sheets (DIN A4, 70g/m²) Price: on request Security level: P3 Power supply: 380 V/ 2.2 kW Machine is fully functional, after technical supervision.
maximum number of results exceeded
please refine your search
1 € 
