vf 200 used for sale

max. wheel diameter: 215 mm gear width: 40,65 mm max. module: total power requirement: 20 kW weight of the machine ca.: 10 t Max. external Ø of workpiece 215 mm Tooth profile, height x width 16 x 40.65 mm No. of teeth 5 - 200 Max. tooth ratio 1 : 10 Grinding wheel Ø 51 - 190 mm Grinding wheel speeds 1,000 - 6,000 rpm X Axis (horizontal) 152 mm Y Axis (vertical) 178 mm Z Axis (slide base plate) 304 mm Distance from middle of machine to middle of workspindle 115 mm Axial speed 125 mm/sec Workpiece speeds 0 - 30 rpm Workspindle bore, conical 3 29/32 inch Total electrical load 20 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features FANUC CNC Control, Model 150 MB, for 7 axes, with monitor and direct input. Automatic calculation of all workpiece and grinding parameters. Extensive coolant equipment with filter system, band filter, etc. Driv ...

max. wheel diameter: 0 mm gear width: 120 mm max. module: 3 min. module: 1 total power requirement: 20 kW weight of the machine ca.: 7,5 t dimensions of the machine ca.: m : : : : : : 5 machines in stock, YOM: between 1986 and 1990 Gear Æ, min./max. 55 / 120 mm Gear Æ for shaft-formed parts 80 mm Module (pitch 25.4 - 8.5) 1 - 3 No. of teeth, min./max. 13 / 80 Pressure angle 14 - 30 ° Helix angle, max. 40 ° Workpiece clamping length 145 - 420 mm Grinding worm Æ 300 - 400 mm Grinding worm width 25 - 40 mm Grinding worm speeds, infinitely variable (35 m/s) 1,650 rpm Feed range 0.4 - 4 mm/rev Total electrical load 20 kW - 380 V - 50 Hz Weight 7,500 kg Accessories / Special Features REISHAUE ...

pressure: 200 t stroke: 400 mm total power requirement: 7,5 kW weight of the machine ca.: 2300 kg dimensions of the machine ca.: 2.000 x 1.200 x 2.800 mm Control: Producer: HIDROLIKSAN YOM: new Type: HD 160 Thrust: 160 ton. Stroke: 400 mm Throat depth: 480 mm Total power requirement: 5,5 kW Distance between frames: 1.200 mm Cylinder-Ø: 120 mm Dimensions (LxWxH): 1.800 x 1.000 x 2.550 mm Weight: 1.400 kg Additional information: • solid, welded construction • pressure cylinder lateral adjustable • operating electrical per switch lever / • pressure indication per Manometer • material support per cylinder, adjustable in height • CE-mark The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

square edge steel: 20x20 / 25x25 mm flat steel: 100 x 7.0 mm round bar steel: 22.0 / 27.0 mm L-beam: 100 x 10 mm weight of the machine ca.: 33.0 kg. range L-W-H: 900 x 430 x 310 mm Features - For precise cold and hot bending of flat, round and square steels - Sturdy design for bolting to the workbench - Infinitely adjustable bending stop - With eccentric quick clamping for efficient working - Readable bending angle up to 120 - High repeat accuracy thanks to bending angle stop - Ideal for repair workshops and locksmiths - - - - - Bending performance cold : Flat steel 100 x 7 mm 65 x 12 mm Round steel 22.0 mm Square steel 20 x 20 mm Angle steel 100 x 10 mm - - - - - Bending capacity hot : Flat steel 100 x 15 mm 75 x 20 mm Round steel 27.0 mm Square steel 25 x 25 mm Angle steel 100 x 15 mm - - - - - Scope of delivery - Bending plate - Angle stop stepless - Clamping block with  ...

plate thickness: 6 mm pressure: 12 t cutting range: Breite x Länge 200 mm no. of strokes: 15 Hub/min cutting angle: 30 - 140 ° total power requirement: 4 kW weight of the machine ca.: 1,02 t dimensions of the machine ca.: 1065 x 900 x 1210 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 t stroke: 400 mm table surface area: Arbeitsbreite 1300 mm pressure: 243 bar oil volume: 64 dm³ ajustment speed: 5,73 mm/sec work speed: 1,84 mm/sec return speed: 7,08 mm/sec total power requirement: 3,0 kW weight of the machine ca.: 1690 kg Inner diameter of the cylinder [mm]: 320 Piston rod diameter [mm]: 140 Diameter piston crown [mm]: 175 - adjustable cylinder (left-right) - Integrated pressure gauge - Pressure regulator - Two-speed hydraulic unit - Working table adjustable in height - Joystick to move the piston up / down - Hand pump for precision work - with digital display This 200 ton hydraulic press is equipped with a movable cylinder (left- right), a height-adjustable work table, a pressure regulator, 2 speeds, a joystick and a hand pump for precision pressing fitted. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 t chamfer lenght: 3600 mm distance between columns: 2650 mm dayligth: 500 mm throat: 300 mm stroke: 250 mm working feed: 10,5 mm/sec return speed: 100 mm/sec ram stroke speed: 150 mm/sec table height: 900 mm oil volume: 500 l total power requirement: 37 kW weight of the machine ca.: 17800 kg dimensions of the machine ca.: 3710 x 1800 x 3390 mm Equipment: - Controlled axes Y1 + Y2 - Manual X-axis with digital position display - Set of upper and lower tools - 2x stop fingers - 2x front support arms - Hand and foot controls - Side + rear safety guard - Operating instructions The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 200 t chamfer lenght: 3100 mm distance between columns: 2550 mm stroke of upper beam: 200 mm throat: 300 mm dayligth: 440 mm working feed: 9.0 mm/sec return speed: 80.0 mm/sec : 265 bar Control: konv. work height max.: 965 mm total power requirement: 15.0 kW weight: 10500 kg range L-W-H: 3360 x 1750 x 2800 mm - in checked conditions - machinevideo - https://www.youtube.com/watch?v=EcmvsA4AGfo Equipment: - simple / conventional electro-hydraulic press brake - pivoting operation, front left - electric, infinitely variable depth adjustment (Y1 Y2 axis) Torsion shaft for parallelism - Electro-motorized backgauge (X axis) with handwheel for fine adjustment on recirculating ball screws 2x manually adjustable stop fingers - manual (jog mode) and automatic cycle selector switch - manual table crowning - split set of roe foot upper tools ... H = 210 mm - 1x as good as new universal  ...

Key data: 200 mm

Hydraulic Machine Vise Hilma 200 mm - 360° rotatable Made in Germany. Jaw width 200 mm. Clamping range up to 348 mm. Jaw height approx. 68 mm. 360° turntable with degree scale. Footplate 370 x 400mm Weight 120 kg.

Key data: 200 mm

Hydraulic machine vise Hilma 200 mm - 360° rotatable. Hilma 3741-05. Made in Germany. Jaw width 200 mm. Jaw height approx. 68 mm. Clamping range up to 348 mm. 360° turntable with degree scale. Base plate 370x 400 mm. Weight 120 kg.

Conrad Boxer 200 drilling rig , Pull-up 4000 daN / kg, Pull-down 2000 daN / kg, Winch//Witch 1450 daN / kg, Year of manufacture 2007, Weight 12,500 kg, Stroke 430 cm, This Conrad Boxer is equipped with:, Caterpillar track , - Caterpillar length center to center : 2600 mm., - Caterpillar width : 400 mm., Brevini EGO200LS winch with 50 meters / Ø10 mm., Soundings winch 200 meters stainless steel wire, Ø 2mm., , Hydraulically driven 4 drill head , , - Max. Drive torque 380 - 400 daNm, - Breakaway torque 475 - 500 daNm, - Max. Speed 80 rpm, , Hydraulically operated changeover clock, suitable for 3 1/2 drill pipes., Spool head suspension with weight compensation, Hydraulically operated catch clamp, Hydraulic tank 480 liters, Hydraulically driven spray pump, Drill pipe manipulator, Drill pipe storage rack incl. 74 pcs. 3-meter 3-1/2-inch drill pipes (222 mete ...

Impulse Pumps proudly presents the SIP 200-8HP, an exceptional addition to our esteemed SIP-series range. This pumpset is meticulously engineered to provide unparalleled pumping capabilities, especially when it comes to handling higher discharge heads. With the SIP 200-8HP, you can experience enhanced performance and conquer even the most challenging pumping tasks with ease., , Equipped with a robust JCB 448 diesel engine, the SIP 200-8HP delivers outstanding power and reliability. This engine, combined with Impulse’s cutting-edge technology, ensures optimal performance even under demanding conditions. You can trust our pumpset to meet the highest emission regulations while prioritizing safety, empowering you to operate efficiently and confidently., , Navigating complex equipment is a thing of the past. The user-friendly Ecomizer-Pro pump controller by Impulse provides real-time insigh ...

Pump is new and unused, assembled by manufacturer, , The SIP-series Screw Impeller Pumps are the do it all” pumps and have become very popular to use in all kinds of wet-construction works. It was just this set-up that has become the middle-man” between the very big market of hi-fuel consuming centrifugal dewatering pumps compared with the very specialized market of super-efficient low-fuel consuming piston pumps. Our 4-inch SIP 100-4 pump set was specially developed to be able to run successfully and efficiently on well-point dewatering without losing its flow while pumping a mixture of water and air. Designed and desired to excel in a wide range of works, our entire range of SIP-series centrifugal pumps handle today’s tough job site conditions. – Impressive solid handling capabilities make them ideal for wastewater, sewerage, mud, and so many more applications you can’t even ...

turning diameter: 210 / 350 mm turning length: 400 mm control: Fanuc 0i-TC swing diameter: 500 mm travel -x axis: 195 mm travel -z axis: 430 mm spindle speed:: 3500 1/min spindle bore: 75 mm bar diameter: 51 mm C-Axis: 0,001 ° turret head: 12 Pos. taper in tailstock-quill: MK 4 tailstock travel: 100 mm diameter of quill: 80 mm rapid traverse X-axis: 30 m/min rapid traverse Z-axis: 30 m/min drive capacity - spindle motor: 11 / 15 kW voltage: 400 V total power requirement: 30 kVA weight of the machine ca.: 4,2 t dimensions of the machine ca.: 2,70 x 1,90 x 2,10 m chip conveyor: 2,80 x 0,60 x 1,30 m Transformer: 0,60 x 0,45 x 0,55 m - Serial-No.: M015356K2F - Machine ON: 14.494 h - control: FANUC Oi-TC - Machine with C-axis and turret for life tools (1x radial + 1x axial in the accessories) - Tool meeasuring arm - Parts collecting tray - Collet chuck - 3-jaw chuck Samchully Ø 250 mm - O ...

grinding length: 2500 mm grinding width: 600 mm workpiece height: 800 mm Table dimensions: 2500x600 mm vertical movement: 800 mm throat: 650 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m filter system The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTec ...

swing diameter: 200 mm centre height: 300 mm weight of the machine ca.: 75 kg dimensions of the machine ca.: m hydraulic steady rest width of arms 40 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 200 mm turning length: 400 mm control: Siemens type: C 200-4 840 C spindle passage: 65 mm Tool changer: 2 x14 Pos. Turret 12-fold, 12 stations: c-axis: live tooling: 2x Revoler total power requirement: kW weight of the machine ca.: 4 t dimensions of the machine ca.: m Main and counter spindle 3-jaw chuck with numerous jaws Hainbuch collets Many tool holders Various driven tools Bar loader Index MBL Chip conveyor with coolant unit Complete set of spindle reducers etc. see photo The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, o ...

turning diameter: 290 mm turning length: 850 mm swing diameter: 600 mm control: Siemens type: 840 D mm spindle passage: 103 mm turning speeds: 3000 U/min live tooling: 3000 U/min rapid travel - grinding spindle: 25 m/min total power requirement: 65 kW weight of the machine ca.: 11 t dimensions of the machine ca.: m Serial No. 1130.2011-30 Equipment: Main spindle / counter spindle 2 power chucks 2 tool turrets C-axis Cabin Chip conveyor Coolant system 22 bar Offer price without tools Optional accessories available for purchase: 106 tool holders for internal and external machining, 20 driven tools (including 10 angle tools) The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane c ...

Bosch Bremsmodul EBX 200-T Nr. 057914-111 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

user power

Machine Type: Deburring Machine Manufacturer: Vangroenweghe Type: T-200-2K/B Year of Make: 2014 Condition: used Offer will only be sent if a complete imprint is provided! Price 9.750 Euro incl. 19% VAT Location Warstein , Germany Reference number M-VAN-0726 DESCRIPTION We offer you a used deburring machine from the manufacturer Vangroenweghe. For technical data, see last picture. Availability: immediately Our offer is aimed at tradespeople who are registered in the sense of the Trade Regulation Act according to §14 GewO. The offer is subject to change, subject to prior sale. Please provide your full contact details to receive a quote with our terms and conditions of payment. Errors in the descriptions and offers are reserved

Deighton forming machine, Type: Formatic R2200 / 180, Serial number: R2200/22/10/368, Capacity: max 4400 products per hour, Hopper: 20 litres, Belt width: 120 mm, Power: 230VAC, 1Ph, 50Hz, 0.75kW, Dimensions: 1150 x 900 x 1500 mm, Weight: 95 kg, Deighton flattening conveyor, Type: FL, Serial number: FL 16/04/036, Belt width: 175 mm, Power: 230VAC, 1Ph, 50Hz, 0.18kW, Dimensions:1450 x 650 x 1200mm, Weight: 48 kg, Deighton preduster, Type: 200W Econodust M/C, Serial number: ED 22/09/068, Belt width: 200 mm, Power: 3 x 400V, 50Hz, 0.51kW, Dimensions: 1600 x 950 x 1400 mm, Weight: 140 kg, Deighton battering machine, Type: 200W weir Econorobe M/C, Serial number: WER 22/09/067, Belt width: 200 mm, Power: 3 x 400V, 50Hz, 0.88kW, Dimensions: 1600 x 950 x 1400 mm, Weight: 140 kg, Deighton mixer, Type: Batter mixer, Serial number: M 22/10/073, Mixer: 200 litres, Power: 230VAC, 1Ph, 50Hz, 1.5kW, Di ...

A Herzog two-head square braiding machine is available. Number of carriers 1/2: 12/16, tandem carrier configuration: 8, horn gear diameter: 150mm/200mm, speed 1/2: 175rpm/131rpm, bobbin diameter: 55mm, bobbin height: 130mm, bobbin capacity: 265cm³. Including 2x change gears, 2x double gears, 28x bobbins, 28x thread tension springs, 2x take-off discs, 6x wooden drums, 8x carrier tubes, 2x braiding plates and one carrier guard. The machine has only been operated for a few thousand running meters and is therefore in very good, near-new condition. Documentation available. An on-site inspection is possible.

200 litre stainless steel tank single-walled container, open at the top

200 litre stainless steel tank Manufacturer : Ahrens & Bode Type: Pressure Vessel Content: 200 litres Technical specifications : cylindrical stainless steel container on feet, single-walled Conical spout Operating pressure up to 5 bar Dimensions: approx. Diameter: 360 mm, diameter lid 500 mm, cone 400 mm Cylindrical height: 1,840 mm Enema: 3x DN 50 Discharge: DN 65

Key data: 660 mm, 1495 mm

Mazak Integrex 200-lV ST CNC turning-milling center with second spindle CNC Control Mazatrol Matrix Turning diameter 660 / 260 mm Turning length 1495 mm Spindle bore diameter 65 mm Spindle nose A2-6 Spindle nose sub spindle A2-6 Spindle speed 35 - 5000 rpm Spindle speed sub spindle 35 - 5000 rpm Milling head speed 15 - 21,500 rpm X-axis travel 580 mm Y-axis travel 160 mm Travel of the Z-axis 1,545 mm Travel of the B-axis 225 ° C-axis indexing 0.0001° (360°) Tool Taper Capto C6 Number of tools in the magazine 120 Barfeeder Irco-Breuning ILS-MUK If you have any questions about the machine, as well as an appointment for a viewing, please contact us by phone or e-mail. Feel free to check out our other ads for a full overview of our stock.

BORCHE BS 200 injection moulding machine was built in 2018 in China by BORCHE BORCH MACHINERY CO., LTD. The machine is designed for the efficient production of technical components and everyday products made from plastics of various shapes and for various purposes. A clamping force of 200 tonnes, combined with reliable components, ensures high efficiency even during intensive mass production. The parts are made by injection moulding, a process which involves injecting plasticised plastic under high pressure into a closed mould, where the material cools and takes on the mould’s shape. This method enables the rapid production of parts with complex geometries whilst maintaining high repeatability and a high-quality finished product. The BORCHE BS200-III Plus injection moulding machine can be further equipped with production automation systems that increase the efficiency of the entire  ...

cutting hight at 90°: 200 mm; cutting width: 410 mm; miter square horizontal: 45° - 90° - 25°; miter square vertical: 60° - 90° -30°; roller convoyer/ supporting table: no; saw blade diameter: 520 mm; speed: 2800U/min; motor power: 5 kW; motor brake: yes; suction connection: 100mm; machine length: machine width: Gewicht: 300kg; crosscut and miter saw Typ ZS 200 N  compact and clear saw to cut large-format cross section this machine is characterized by following properties: †clarity by cutting process because saw blade arranged above †extremely large cutting area  with a compact and stable structure â€Â powerful 5 kw three-phase motor with automatic star delta start †fast miter adjustment  - horizontal meter range of 45° †90° †25° - vertical meter range of ca. 60° †90° †30° - acu ...

Cutter head, milling chuck, carbide cutter, indexable insert cutter, face milling head, milling head, cutter head shell cutter, face milling cutter, corner milling cutter -Manufacturer: Sandvik Coromant, face milling cutter -Type: R 265.2-200M -Mount: Ø 60 mm / Bolt circle Ø 102 x 18 mm -Dimensions: Ø 205 x 62 mm -Weight: 8.6 kg

Dairy Machinery UK Farm Milk Cooling Tanks, Space saving, ergonomic design-chassis with solid leg construction and adjustable feet., Constructed completely from AISI 304 Stainless Steel, welded and polished to global food grade standards.Insulated with CFC free polyurethane, thickness varying from 38mm at the top to 100mm at the bottom, adding extra strength to the structure., Laser Welded S.S 304 Evaporator (0.9/1.5/2mm). Milk Cooling Tank consists of milk vessel made from 1.5mm S.S 304 and insulation vessel made from 1mm S.S 304., Detachable Butterfly valve-DN 50, SMS thread One piece top Lid made from S.S 304 with thickness of 1.5mm mounted with pneumatic springs to allow easy and safe opening and closing of the tank. Gear motor with micro switch for gentle agitation of RPM 30-36,1Φ-50Hz from Dairy Machinery UK, Make: Dairy Machinery UK, Model: FMCT-200 L , Capacity: 210 Litres , Coo ...

Mengele paternoster with 42 shelves High-quality, extremely space-saving vertical carousel rack (storage paternoster) from the renowned manufacturer Karl Mengele & Söhne The system works according to the paternoster principle and brings the stored goods directly to the ergonomic removal opening at the touch of a button. Perfectly suited for tools, spare parts, small parts storage or documents in the workshop, warehouse or archive. Technical data at a glance: • Manufacturer: Karl Mengele & Söhne • Type designation: 130-200/12 • Number of shelves: 42 pieces • Maximum permissible shelf load: 100 kg (per tray) • Permissible maximum bay load: 4,200 kg (total load capacity) • Nominal consumption / power: 3,000 W (3 kW) • Connection: 380 V (three-phase / high-voltage) / fuse 16 A • Permissible unload: up to 20% • Year of manufacture: 1985 Dimensions ...

TECOM BLOWN FILM EXTRUDER, for LDPE-RLDPE blends, Contrex feeding, 2 gravimetric components + 1 volumetric dosing units, Screw diam.70 mm 30 L/D, Rotating head, Low neck, 1.600 mm pull off unit, gusseting unit, Cason corona treatment, single color printer (for marks), 1.600 mm double collection frame, BRA 36+ Eurochiller, Connected and running., conditions: used - running, working width: 1600, availability: February 2026

Features Volume 6200 L Material No. V2A Total height 2050 mm Cylinder height 1740 mm Outer diameter 1740 mm Depth 2700 mm Description Tank crest: Weld-on nozzle DN50 Front: Cone base Tasting tap Manhole 410 x 320 Nozzle Flap Size 37 Rear: Cone base Underbody: Residual drain pipe with angled seat valve DN50 2 bearing cups

Combined heat and power plant (CHP) for natural gas operation Manufacturer: Viessmann Year of Make: 2017 Operating hours: 22,334 h Plant starts: 2580 Electrical power: 8.5 kW Thermal power: 20.1 kW Energy input H: 30.1 kW Electrical self-consumption max.: 0.15 kW Flow temperature min./max.: 50/85 °C Return temperature min./max.: 30/65 °C Permissible operating pressure: 1 MPa (10 bar) Condition and availability: The CHP unit is in a well-maintained condition and is immediately available. This system is particularly suitable for economical and self-sufficient heat and power supply in small to medium-sized applications.

Features Volume 6200 L Material No. V2A Total height 1900 mm Cylinder height 1700 mm Outer diameter 1740 mm Depth 2700 mm Cooling jacket design Description Tank crest: Weld-on nozzle DN50 rear Front: Cone base Tasting tap Manhole oval 420 x 310 Nozzle Flap Size 37 Residual drain pipe DN50 with angled seat valve Rear: Cone base Underbody: 2 bearing cups

: gebraucht : 2907D : prompt, Zwischenverkauf v : Taiwan : 945 € : 1 : 200 mm : 62 mm : 300 mm : 110 kg : 8500 kg MINT CONDITION with turning base accurate adjustment of clamping force by use of a dial cast iron body hardened and ground slideways vice jaws made of special hardened alloy steel are precision ground (sample photo) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

NEGRI BOSSI 55 T type V55-200 CANBIO? Force de fermeture : 55 T Diamètre vis : 28 mm Rapport L/D : 20 Volume d’injection : 92 cm3? Capacité d’injection : 84 gr de PS? Pression d’injection : 2100 bars? Épaisseur moule mini/max : 120/350 mm ?Entre colonnes H-V : 315 x 280 mm Dimensions des plateaux : 455 x 430 mm? Commande : DIMI EL 2 Interface colorateur ?Noyaux hydrauliques : 1? Noyau air : 1 Dimensions. : 3,72 x 1,18 x 1,80 m Poids : 2000 kg

Key data: 2000 , 50

KRAUSS MAFFEI 200 T type CX 200-750 Clamping force: 200 T Year: 2011 33 000 operating hours Screw diameter: 50 Injection volume: 393 cm3 Injection pressure: 1892 bars Tie-bar spacing: 560 x 560 mm Opening stroke : 700 mm Maximal distance between platen : 1050 mm Power install : 37 KW Dimensions : 5,20 x 2 x 2 m Weight : 11 500 kg

: neu : ca. 8 Wochen ab Auftragse : Türkei : 29990 € : 572.81 € : 0.4 - 3.5 mm : 200 mm : 700 mm² : 80 mm : 75 m/min : 10 m/s² : 10 Nm helical gear boxWATTDRIVE (Made in Austria) FESTO pneumatic equipment servo drive and control SIEMENS 7", colour touchscreen SIEMENS 2 driven rolls OPTIONAL EQUIPMENT Handrwheel and Simlinx remote control € 4.290,-- The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

General SKU273K305 MakeHaagen &: Rinau Mischtechnik Bremen TypeSRC-200 No.8233751 Year of construction1987 LocationBarneveld Pressure Working pressure3 Bar Vacuum possiblecheck Working pressure jacket4 Bar Main Features MaterialStainless steel Volume345 Ltr. Motor6 KW Specified Features - Processing vessel Closed stirring vessel:Vacuum processing vessel: (1x) Capacity345 Ltr (useful capacity 50-200 Ltr) Vessel sizesdia. 740x550mm Dished bottomcheck Dished top sidecheck With covercheck With jacket(32,5 Ltr) Max. temperature143/151 Degr. C. (vessel/jacket) With anchor stirrer:scraper stirrer: (Teflon scrapers missing) Motor5,5 KW, 220/380 Volt Speed mixing shaftvariable With homogenisercheck Motor1,5/6,0 KW, 380 Volt MaterialStainless steel 1.4301 (304) With jacketcheck General Floorspace2,2 x 1,2 M Total height2,9 M Weight1800 KG Extra Specifications- W ...

General SKU291Y541 MakeFryma Koruma TypeDH-A 140/200 No.4.209 Year of construction1988 Motor Motor power11 kiloWatt Main Features MaterialStainless steel Motor11 KW Inlet diameter100 mm Specified Features - Colloid mill Colloid millcheck Rotor sizesø 125 x 140 mm Teethed rotorcheck With hopper± 200 l. Inletø 100 mm Outletø 70 mm Motor11 kW, 380 V, 2910 rpm Speed2910 rpm MaterialStainless steel 1.4571 (316Ti) General LocationBarneveld With switchgearcheck Floorspace1,4 x 0,8 m Total height1,4 m Weight350 kgOils & fatPaints & coatingsGeneric medicinesOintmentsBiotechnologyFeed additivesColloid millsDetergent & surf.CosmeticsFood additivesLubricants & oleoDairyConfectioneryBeveragesBiopharmaceuticalNew arrivalsMinerals & inorganicFryma KorumaIndustries > Food & Feed > Oils & fatIndustries > Chemical > Paints & coatingsIndustries > Pharmaceutical > Generic med ...

: gebraucht : 2891C : China : 250 € : 1 : 200 mm : 63 mm : 160 mm MINT CONDITION turning base for drilling-, shaping- and milling machines mechanical clamping vice bocy made of cast iron (sample photo) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 4 Monate ab Auftragse : Italien : 55200 € : 1043.28 € : 200 to : 500 mm : 1000x600 mm : 640 mm : 21 mm/s : 2 mm/s : 5.5 kW : 1800 mm : 1300 mm : 2500 mm : 6400 kg 2 speeds adjustable max. pressure manomete The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

High-pressure clamp vise MC2 / 200 ORIGINAL PRICE: ~ $1,650.00 Description: - Body made of cast iron FCD 65, jaws made of steel - Ground on the bottom and sides - Anti-lift mechanism - Built-in pull-down mechanism - Mechanical force amplification, seal-free and maintenance-free - Short design - Clamping force can be preset Technical data: Jaw width: 200 mm Vise opening: 300 mm Jaw height: 55 mm Dimensions: 600 x 180 x 210 mm Weight: approx. 90 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

saw blade diameter: 520 x Ø 50 mm cutting diameter: 200 mm cutting length: 420 mm Cutting height at 45°: 140 mm dimensions of saw-blade: 520x3,6/3,0x50 mm turning speeds: 2800 U/min Dust suction hood: 100 mm total power requirement: 3,0 kW weight of the machine ca.: 310 kg. range L-W-H: 1400 x 900 x 1650 mm - Crosscut and miter saws for crosscuts - Miter adjustment on both sides (60°/45°), with fixed stops - Shift cut on both sides (60°/45°), with fixed stops - Stable cast iron construction - Precise ball bearing guidance of the tool slide hardened and welded steel shafts - manual saw feed - Saw blade infinitely adjustable in height - socket for opt. suction Furnishing : - 3.0 kW motor for ALU cuttings - Saw blade can be tilted via handwheel and worm gear (shift cut) - Saw blade diameter 520 mm - Saw blade mounting hole 50 mm - Saw blade speed 2,800 rpm - 400 Volt / 3 kW (S6/40%)  ...

plate thickness: 8.0 mm ST plate thickness: 5.0 mm VA table-size: 1000 x 950 mm blade length: 200 x 200 mm strokes per minute: 60 H/min adjustable: Winkel 30°-140° mm work height max.: ca. 950 mm oil volume: 60.0 l engine output: 4.0 kW weight of the machine ca.: 1200 kg range L-W-H: 1000 x 1120 x 1700 mm from a maintenance workshop New price at the time ~ 21.000 euros Furnishing: - Robust electro-hydraulic notching machine - with adjustable angle, electro-hydraulic adjustment - Adjustment by hand wheels (left + right knife segment) - hardened knives also for cutting stainless steel - front panel - electro-hydraulic knife clamping - Inching mode for setting the shear blades selectable (manual mode) - planed table surface, with T-slots to avoid tilting or slipping of the metal sheet - 2x staking stops with movable and interchangeable stop bars - 2x blank holders - 1x free moving foo ...

plate thickness: 4.0 mm thickness at Niro-steel: 3.0 mm blade length: 200 mm angle adjustable from - to: 30 - 120 Grad no. of strokes: 60 Hub/min oil volume: 60.0 ltr. table:: 1000 x 800 mm total power requirement: 2.62 kW weight: 800 kg range L-W-H: 1000 x 1500 x 1440 mm Furnishing: - robust hydraulic notching machine, with adjustable angle - Adjustment range 30 - 120 degrees Adjustment with the 2x front handwheels - hydraulic clamping and locking - Infinitely adjustable cutting depth, with digital display - 2x locking accuracy stop, with stop bars - Stripper for sheet metal cutting - Collecting container for clippings - Freely movable foot pedal for triggering the stroke The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: neu : ca. 4 Monate ab Auftragse : Italien : 82000 € : 1549.8 € : 200 to : 500 mm : 870x500 mm : 1000x600 mm : 500 mm : 300 mm : 21 mm/s : 3 mm/s : 7.5 kW : 2300 mm : 1500 mm : 3000 mm : 8200 kg 2-fold round guidance table and ram with T-slots 2 hand operation Siemens PLC manometer users manual OPTIONS: Light barrier € on Request Siemens control for programming of stroke and press time € on Request Siemens touchscreen-control, 50 programsstoreable, for programming: • Upstroke and downstroke quota • Break time in the bottom • time of Decompression • setting pressure of work • Pieces counter • prestop in upstroke and downstroke • setting for movement in manual and in automatic • management of alarms and anomalies € on Request Working hour counter € on Request Stroke counter € on Request Deompression valve € on Request Oil cooler with decompreission  ...

: neu : ca. 10 Wochen ab Auftrags : Türkei : 40900 € : 781.19 € : 2050 mm : 10 mm : 10 mm : 8 mm : 8 mm : 6 mm : 200 - 220 mm : 200 - 220 mm : 160 mm : 1,5 / 6 m/min : 5.5 kW : 4400 mm : 1150 mm : 1250 mm : 3950 kg 4 rolls Top rolll driven by hydromotor and planetary gearbox, bottom roll driven by gear and cardan system Pinch roll and latereal rolls move with hydraulic cylinders Digital read-out for lower and side rolls position Hardened rolls Conical bending device Hydraulic load relieving of upper roll Hydraulic drop-end bearing 2 working speeds Protectionagainst overload Moveable control pane According to CE rules OPTIONAL EQUIPMENT: Infinitely adustable speed of rolls Hydraulic side support Hydraulic top support NC control IMPORTANT ISSUES AT CONICAL BENDING: The max. sheet metal thickness isequivalent to 50 % of nominal capacity The cone length can be max. 30 % oremust be more  ...

: neu : ca. 12 Wochen ab Auftrags : Türkei : 30900 € : 590.19 € : 200 to : horizontal verschiebbar : 300 mm : 1900 mm : 320x210 mm : 5 mm/s : 20 mm/s : 2460 mm : 1600 mm : 2700 mm : 4800 kg horizontal movable cylinder by handwheel steel welded frame stop at any position pressure manometer safety valve against overloading 2 V-blocks table height adjustable table up-down movement attachment control by operating lever according to CE regulations user manual in GERMAN and ENGLISH (sample photo shows mod. HDK 1570/150) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.