vertical boring mill used for sale

Key data: 300 , 600

Rollers: dia. 300 x 600 mm Roll surface: smooth Rollers type: hollow bored NIP adjustment: Manuel Engine: 22 kW

Qty. 1 Second-hand roughing, finishing mills and special equipment Mfc.: DAVY, TMEIC, TOSHIBA, MITSUBISHI Type: 4-Hi Rev. Built: 1997 Revamped & Installed: 2008, 2011 Stopped in 7-2017 Revamped cost of USD 151.0 Mill. from 2008 up to 2011 Finishing mill equipped with CVC Roll plus Technology System Finishing mill – new hydraulic adjustment to increase rolling force to 90 MN Roughing & Finishing mills: Technology Control System (Level 1) Process Models (Level 2) for pass schedule calculation, profile & flatness control (PFC), Pacing system & Material tracking Revamped by SMS in 2011: Roughing mill: Slipper-type Spindles Product capacity: 2,000,000 ton/year Mill capacity: 30 Plates/h Entry Material: Slab T130~300 mm x W1,200~2,200 mm x L2,350~4,000 mm Final Product: Plate T5~180 mm x W1,200~4,100 mm x L max. 25 m Application: Ship building plate & Pipe pro ...

Impact mill according to photos

Milling Machine MAHO MH 700 C CNC- 5 axis CNC- Phillips 432 X/Y/Z- 700/450/500 mm B axis CNC Universal table 820x480 mm 5th axis- CNC/NC dividing head ISO 40 spindle adapter Quill stroke of spindle 100 mm Universal table: -swiveling of the Horizontal X/Z axis 30 degrees -swiveling of the vertical Y axis 360 degrees Spindle speeds infinitely variable 20-3150 rpm

BALLISTRINE- linear profiler,/shaper-double sided 10 hp cutter head per side- follows your templates - shapes both sides- 9' table- hydraulic feed- material hold downs- $7,800

Qty. 1 Second-hand Duplex board paper mill Mfc.: Hasegawa, Yodogawa, Fuyo Japan, Valmet, Finland, Kumsun, Chung Korea Buil: 1984 Width: 3400 mm Speed: 330 m/min. Productivity: 450 ton/day max. 350 ton/day (average) GSM: Max.500 g/m2 -The number of HEAD BOX: 7 sets -Fourdriner type -Dryer: 77 ea (Air type+Electric type)

Various Grinding Stones

Mikron C Axis Machine Table - with Heidenhain control 430 - Siemens server motor - Table: 60 x 110 cm - 4th axis, diameter: 50 cm - Weight: 650 kg Good condition fully functional can be visited and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article, in order to avoid misunderstandings, can be viewed before the purchase and tested under electricity. Please ask questions before buying to avoid ambiguity. For general questions or an appointment for a viewing, I can be reached at any time at the telephone number below or above. Errors in the description and prior sale excepted. VAT will be shown separately on my invoices. Shipping with freight forwarder.

Cylinder mill for very fine grinding, consisting of three pairs of cylinders, new machinery, stainless steel construction, never been used, complete with product feeder, three electric motor and hydraulic control unit

2130 2x3 M 3D CNC milling plotter built in 2014 in China, is used for machining workpieces in the X,Y and Z axes. Machining is performed on the machine’s vacuum table with dimensions (L x W) of 3000 x 2100 mm, by using a rotary head. The applied electro-spindle with a power of 4.5 kW, is distinguished by its extreme reliability and speed reaching up to 18000 rpm, allowing the desired result to be obtained in a very short time. The CNC milling machine is controlled by a hand-held terminal connected to the WEIHONG NK105 G2 CNC controller. This solution makes the machine’s operation much easier to handle and allows every function to be used. The machining centre is also equipped with among others: an EMI filter to attenuate high-frequency electromagnetic interference and a PANASONIC MDME102GCGM axis servo motor. Technical specifications of the 2130 2×3 M CNC milling machine - wo ...

Stock number: U2293-2 Used carbon steel grinding/refining mill by Pallmann (Germany) model PR8. Mill has bolted rotor with diameter 795 mm and stator with diameter 800 mm. Belt driven by el. motor 100 kW, 1480 rpm, 380 V, 50 hz. Manual adjustment of gap between milling plates. Mill has mounted 5 nozzles for feeding gas or liquid inside the milling chamber. Front door bolted with central feeding inlet through feeding chute. Bottom discharge.

Rotor Ø: 340 mm Working width: 410mm Motor power: 11-18.5 kW Rotor cutting strips: 5 Stator cutting strips: 2 Insertion opening: approx. 410 x 340 mm Capacity depending on plastic and screen size: approx. 130-400 kg/h Granulate conveyor: 1.1 kW Net weight: approx. 1640 kg Gross weight: approx. 1865 kg Box dimensions: approx. 2.2 x 1.7 x 1.6 m Feed belts with silencer Centre distance: 3700 mm Belt width: 400mm Net weight: approx. 296 kg Gross weight: approx. 430 kg Box dimensions: approx. 0.8 x 0.8 x 4.4 m - Overhaul in 2022 - Real bevel cut - Integrated sound insulation - Conveniently designed grinding room - Safe material acceptance - Optimum granulate quality - Built-in granulate conveyor system - Easy maintenance and cleaning - Tested occupational safety Ø of rotor: 340 mm Useful width: 410mm Motor output: 11-18,5 kW Rotor blades: 5 Stator blades: ...

l 45 kw POWER 680 kg/h (depending on material/full load) Active process and computer-controlled Koller PP 300 is a pellet line consisting of the following machines: - DOSAGE SYSTEM with an automatic PLC control from the feed of the ground material incl. rotary valve - Hammer mill with sieve 6 mm for wood chip raw material - Pellet mill with main motor 45 kW with automatic hydraulic control system (Eur.Pat. EP1619012B1). Patented system. The pressing process is completely monitored by a controller and monitored via mobile phone. incl. minisilo for loading with level sensor; Safety system to control the blockage of the Matritze Humidity monitoring - Cooling and dedusting system for the pellets produced via a screw

Several BÜHLER MDDK roller mills in different versions on sale. Any sort of feeding With or without inlet glass Scraper knifes, single or divided spout Plain rolls or corrugated rolls Size 1000 mm or 800 mm with roller diameter 250 mm Our specialists will provide a liable solution with used Buhler MDDK roller mills at good value.

technical details: - Milling depth: 0 - 80 mm - Diameter suction nozzle: 60 mm - Swallow size: W-1/2/3 - Dimensions (W x H x D): 600 x 770 x 540 mm - Weight: 19 kg - Operation: manual - Workpiece clamping: manually via hand lever - Passage height: 110 mm Stop elements: -1 x Stump Stop - 1 x stop plate 45° (angle stop) - 1 x measuring scale (All settings are done manually.) Controls: - 1 x milling depth adjustment - 1 x workpiece clamping - 1 x chip breaker Motor data (milling unit): - Power: 0.5 kW (530 W) - Voltage: 230 V - Frequency: 50 Hz - No-load speed: 29,000 rpm The machine mills one keyway per work cycle for the above-mentioned dovetail sizes. All Hoffmann accessories can be used on this machine. (Changes and errors regarding technical data and prices excepted!) In accordance with our terms and conditions, we would like to point out once  ...

HELMA- model CF-40-copy milling/shaping machine feed thru with work piece return (2) milling spindles- 18" max. distance between the spindles centers- 28" x45" Table - (2) 30mm. work spindles- 10,500 RPM spindles- 4"max. cutting height - vertical adjustment 10 mm.- (2) 7 1/2 hp. spindle motors - 1/2hp. variable speed feed motor 5' to 30' per min.- 2,200 lbs. $7,500

VISION WIDE VB-2016 5-AXIS CNC gantry milling machine was manufactured in 2013 in Taiwan. The machine performs precision machining of heavy workpieces in three or even five axes, once the automatic swivel head is mounted to the vertical spindle. The machine’s top-quality cast-iron structure is rigid and resistant to bending stress, thus perfectly dampening the vibrations and oscillations generated during machining. The VISION WIDE VTEC VB 2016 CNC gantry milling machine centre is equipped with safety guards fitted around the entire machine with sliding doors that open flush with the X-axis travel. Inside, there is a large work table with a length of 2000 mm and a width of 1300 mm, which is supported along the entire length of the longitudinal travel and guided by two sliding guideways, making it possible to machine heavy workpieces even when the table is unevenly loaded. Two scre ...

SERON 1315 EXPERT CNC milling machine built in Poland in 2017 is new and has never been used. The machine designed and manufactured with attention to the smallest details, is used for precision machining of a wide range of materials such as mild metals, plastics, carbon, wood, wood-like panels and glass. All vibrations and deformations during the milling process are eliminated by the high-quality ribbed steel construction with a T-slot table made of aluminium profiles, with a length of 1500 mm and a width of 1300 mm. The workspace is additionally equipped with a special PVC overlay to protect the table cover while cutting the workpieces through. At the end of the table there is a six-position linear magazine with an automatic tool correction sensor. The 1315 EXPERT machine axes are driven by highly dynamic and precise brushless AC servo drives with back pressure, equipped with serv ...

Impact forming mill is used for dry and fine grinding of brittle materials with a hardness of up to 3 Mohs. the impact fine grading mill combines efficient impact grinding with efficient classification in one unit. The supplied materials are thrown into the liner by the milling tools at a speed of 60-130m/s and then shredded. the ground material is transported to the integrated cashier for processing by means of air and rotation of the grinding tool. the fineness can then be infinitely adjusted via the speed of the classifier. Particles that are too large are sorted out by classifiers and end up in the grinding zone for continuous comminution.

BALLISTRINE- C 70 N- auto feed thru (2) sided shaper(2) 10HP; 3PH spindle motors • (2) 30mm diameter spindles with 5in. under the nut • Spring loaded floating spindles • In-feed and out-feed rubber covered upper feed rollers • Working width 14.4in. (360mm) max • Working height 4.8in. (120mm) max • Min working length 9.6in. (240mm) • Spindle 8,000 RPM • feed 3 to28..Price-$8,900

Features and advantages of the classifier mill ACM: • Grinding and classifying in one machine. • Excellent selectivity, steep particle size distribution. • Infinitely adjustable fineness. • Flow-optimized, conical classifier wheel guarantees product without oversize grain and low wear compared to cylindrical classifier wheels. • Cool and gentle grinding due to high air flow. This makes the ACM ideal for processing temperature-sensitive products. • Deflection area in the grinding chamber lid: classifier gap flushing not required. • Low noise emission. • Very good running characteristics due to the belt-driven grinding disc. Bzc3pyxj32 • Easy to maintain: motors and bearings easily accessible. • The lid lifting device allows quick access to the grinding and viewing zone for cleaning and retrofitting. • Extremely compact and space-saving design. • Option ...

Table size: 254 x 1100 mm Table movement x: machine. u. v. hand 682 mm Table movement y: hand 380 mm Table movement z: hand 457 mm Milling head swiveling to: +/-90 or +/-45 ° Spindle retainer: ISO 40 Spindle speeds: 70-2300 rpm Quill feeds: 0.038 â 0.152 mm / min Spindle drive: 380 V, 2.2 kW Space: 1600 x 1600 x 2150 mm Weight: 1420 kg

ZERMA GSE 700 plastic granulator machine manufactured in 2018, is used in the processing of lightweight plastics such as PE, PP or PVC. The granulator has a specially shaped hopper with splash protection, inside of which there are fixed knives and a rotor with knives arranged in a ‘V’ shape. The rotor is driven by a slide-rail-mounted electric motor with tension-screw adjustable V-belts. The ZERMA GSE 700 plastic granulator machine can even cope with larger pieces of plastic, such as lumps and film rolls, thanks to the use of a deflecting wedge and block knives to prevent the rotor from blocking. All of the machine’s components are mounted on a base frame, fitted with mounting pads to dampen noise and vibration.

x-280 ,y- 200 , Z 315 , Table dimensions 380x380/250x500 A lot of writings,much more than pictured

Complete grain mill for sale for about 75 tons per day. Rollermills Bühler MDDK Plansifter MIAG LM The plant has been professionally dismantled. All machines have been overhauled. With switchgear and PLC control.

Used hammer mill made by Alpine, type B 630. Manufacturer's documentation.

Bearing number 1105-02690 Machine type Milling machine - Universal Make HERMLE Type UWF 1000 Built in 1988 Control type CNC Storage location FRANCE Country of origin Germany Delivery time SOFORT Freight base EXW Technical details x-way 700 mm y-way 630 mm z-way 500 mm Control heidenhain 355 Tool holder SK 40 (DIN 69871) Table clamping area: 1000 x 490 mm Spindle speed Gear stage 1 25 - 400 rpm. Spindle speed Gear stage 2 401 - 1260 rpm Spindle speed Gear stage 3 1261 - 4200 rpm Feed 5 m/min Rapid speed 10 m/min Swivel of the milling head + / - 90 ° Pinole diameter 110 mm Pinole stroke 95 mm Total power requirement 18 kW Machine weight approx. 5 t Information with full cabin coolant device Sale takes place without clamping equipment approx. 8500h switch-on hours

Universal tool milling machine DECKEL FP 1 with 3 axis active digital display Heidenhain TNC 113 Year of construction: 1987 Travel: X 300 Y 160 Z 340 Speed range: 40 – 2000 rpm With the following accessories: Universal table 600 mm x 250 mm clamping surface Movable vertical milling head Extendable drill quill Infinitely variable feed via potentiometer 1 machine vice 1 counter holder with counter bearing 1 pc. milling mandrel long 0 22 mm Various tool holders S 22 x 2 Bellows Z Axis Machine light Automatic central lubrication pump Chip collection plate Coolant system Operating instructions THE MACHINE IS IN VERY GOOD CONDITION

U5 Lab Package For Pilot & Development Construction: 305 stainless steel with 316L stainless steel product contact parts. Surface Finish: Product contact surfaces mirror polished (Ra 0.10 micron), non-contact surfaces 150 grit (Ra 1.06 micron); welds cleaned and polished and all material contact welds ground flush and polished. Infeed Opening: 3.25" (83 mm) diameter with grid bars to prevent operator access to the rotating impeller. Infeed Chute: Hand-fed funnel, 6.4" diameter x 5" high (163 mm x 127 mm) with magnetic actuated safety interlock. Spindle Assembly: Sanitary pharmaceutical duty with pre-lubricated, sealed bearings, viton O-ring, two shaft seals, and double varilip seal in a stainless casing. Also suitable for use with vacuum. Impeller Speed: Approximately 1000 - 6500 RPM. Capacities: Varies based on tooling, feed and speed used. Discharge: 6" (152mm) tri-clamp di ...

Table surface: 300 x 1300 mm Table movement x: 950 mm Table movement y: 220 mm Table movement z: 400 mm Spindle intake: MK 5 Spindle speeds: 25-1200 rpm Prests lengthwise & across: 7.5-635 mm/min Presens vertical: 3-250 mm/min Electr. Connection: 380 V, 7.5 kW Space requirement: 1670 x 1500 x 1750 mm Weight: 2600 kg

Qty. 1 Second-hand cold rolling mill Mfc.: MCC, ABB, IMS Type: 6-Hi Cold Rolling Mill Built: 2009 Stopped: 2017 Annual capacity: 220,000 Ton/Year Annual running time (Hour): 6480 Strip Width: 800~1250 mm Thickness Entry: 1.5~3.5 mm Exit: 0.2 – 1.2 mm De-Coiler OD: 1000~2000 mm De-Coil ID: 610 mm De-Coil Weight: Max. 25 T Coil OD: 1000~2000 mm Coil ID: 610 mm Coil Weight: Max. 25 T Mill Max Speed: 1300 m/min Threading Speed: 30 m/min Main Drive Controller (3300 VAC) Mfc.: ABB ACS6000 Variable Speed Variable Voltage Xray Gauge Mfc.: IMS Germany Automation Siemens PLC/Wincc

Grinder mill with open rotor blades, cutting chamber: 430x200 mm, motor: 5.5 kw. With electrical panel. We offer a highly efficient shredder mill with blades and open rotor, designed to optimize the reduction of plastic materials. Our machine features a 430x200mm cutting chamber and a 5.5 kW motor that ensures solid performance in plastics processing. In addition, we include an electrical panel that facilitates the control and safe operation of the machinery. At [Your Company], we are committed to providing state-of-the-art solutions for the thermoplastics management and recycling industry. Ready to get started? Contact us directly! Send us a WhatsApp message to (+34) 647 590 257 or an email to infogester.es for personalized advice.

Technical data: Fixed angular table: Fixed angular table clamping area: 800 x 400 mm Max table load: 200 kg Working spindle: Tool holder horizontally and vertically: ISO 40 Power of the main drive motor / 100% ED: 2.2 kW Vertical milling head: Speed range, tiered: (12) 50 - 2000 rpm Drill pinole, stroke: 100 mm Swivel range: +/- 90° Travel: X-axis automatic/man.: 385/400 mm Y-axis automatic/man.: 185/200 mm Z-axis automatic/man.: 365/380 mm Feeds: Feed range: 0-650 mm/min Number of feeds: infinitely adjustable Rapid response: 1000 mm/min Characteristics: - Machine accuracy according to DIN 8615 - 3-axis digital displays FAGOR® Innova (option) - Spindle run max. 0.005 mm, incl. test protocol according to DIN 8615 (rolling bearing SKF®/NSK®) - Vertical milling head can be swivelled out for horizontal milling (without d ...

ID2430 Waagner Biro Wet Ball Mill 260 x 550 cm year/Year of construction 1987 52 t Wet ball mill, overflow ball mill, drum diameter 2600 mm, grinding track length 5500 mm, ground material: limestone 0-10 (16 mm), wet grinding process, 2-stage cyclone circuit, nominal grinding capacity: 12-22 t/h, filling weight max./normal: 44/39 t, installed engine power: 450 KW, rubber Skega armor Wet ball mill, overflow ball mill, drum diameter 2600 mm, grinding track length 5500 mm, regrind: limestone 0-10 (16 mm), wet grinding process, 2-stage cyclone circuit, nominal grinding capacity: 12-22 t/h, filling weight max./normal: 44/39 t, installed engine power: 450 KW, armouring rubber skega

x-400,y-330,z-350,angle table 630x335,SK 40, 40-6,000 rpm,measuring probe

Hammer mill Fa. Wery

Complete mill / mill plant with a capacity for the production of 100 tons of flour/24h consists of: Grain cleaning systems, bucket elevators, conveying augers, stainless steel pipe systems, etc. The automated mill has been continuously modernized and expanded. 1 Airtronic roller mill, made by Bühler 1 top-mounted filter, made by Bühler 1 Dust cleaners 1 double screening machine, Fbrikat Bühler 3 MJZF, make Bühler dissolver, total 7 metal silos for grain Conveyor systems and stainless steel pipe systems 1 Compressor systems Laboratory equipment consisting of: 1 glue washer 2 Perten Inframatic 8600 1 case counting device 1 gluten index device 1 Schlagkreuzmühle To the flour store: Storage cells 6x 7.5 tons Storage cells 2x a 25to 1x 15to -------------------- Elevators: 3x A 75to  ...

1 x Universall tool-feeding machine Lid FP 4 Built: c.1970 Very robust and rare conventional machine in good condition. Technical data: Travel: X: 700 Y: 400 Z: 450 mm Spindle speeds: 31.5 - 1,600 rpm (18 levels) Tool holder: ISO 40 Pinole stroke: 115 mm Feed in X/Y/Z Feed range: X/Y/Z 5 - 500 mm/min (infinitely adjustable) Rapid response: X/Y: 10 - 500 mm/min Z: 5 -250 mm/min (18 levels) swivel handling table Clamping area: 860 x 500 mm Accessories: 1 x horizontal counter bearing 5 x horizontal frond spine Bftj7cazem 10 x vertical fraes aufnahme 36 x tension tension ingesheis from 0.5 - 18 mm 0.5 mm rising 5 x Direct clamping pliers D: 12/14/16/18/20 mm 1 x machine vice Manual various distance rings and accessories for milling machines complete documentation The machine can be inspected at our warehouse under electricity. A 3-axis digital ...

Qty. 1 Second-hand 4 stands cold rolling mills – 4-Hi Mfc.: Fröhling Built: 1969 Revamped hydraulics: 1984 Dismantled and in storage 2018 Rolled material: Alloy AA5050, AlMg3 (Series 3000 & 5000) Type: 4-Hi Strip width max.: 282 mm Thickness: in 2.0 mm out 0.25 – 1.20 mm Speed max.: 400 m/min

Peforated disc mill Manufacturer: Fryma Type: ML 180 No.: M10451 Power: 7.5 kW with hopper (volume: ca. 100 l) with feed screw (speed-controlled) on mobile cart with control cabinet LWH: 800 x 700 x 2400 mm Weight: ca. 250 kg

5 Qty. 1 Continuous 6 Stand Cold Rolling Mill Mfc.: Fröhling Built: 1984 Type: 4-Hi Strip width: 220 mm Thickness: 0.15 – 2 mm 8 Qty. 1 Strip welding machine (Cold mill) Mfc.: A.I. Welders Built: 1986 Rev. in 2002 Speed: 75 – 600 m/min. Width: 233 mm Thickness: 0.175 – 2.0 mm 9 Qty. 1 Induction Treatment Furnace (Cold mill) Mfc.: Otto Junker Built: 1986 Width: 220 mm Thickness: 0.175-2.0 mm Speed: 8-60 m/min. Temp.: 550 °C 10 Qty.1 Quenching unit (Cold mill) Mfc.: Otto Jumker Built: 1986 Flow: 95 m³/h Temperature: 29 °C Size: 1.2 x 1.2 x 2.8 m 11 Qty. 1 Rotary shear (Cold mill) Mfc.: HDE Built: 1996 Strip width: 220 mm Thickness: 0.1 – 0.95 mm

Mfc.: Hitachi Type: 6-Hi reversing mill Built: 1976 Shut down: 2014 Revamped: 2010 Control system – changed DC to AC motors Load cells were replaced in March 2005 & thickness gauge in March 2009 Roll coolant cooler was replaced in July 2009 Control boards of hydraulic screw down & electromagnetic valves were replaced in 2009. Strip width: 610 – 1330 mm Thickness Entry: 1.6-4.5 mm Exit: 0.15 – 2.3 mm

Demo Machine Specifications:  Dimensions - 1300 x 1560 x 1210 mm, (with built-in drive and control cabinet)  Dimensions of the packed machine - 1500 x 1800 x 1320 mm,  External dimensions of the mill drum - Ø870 x 1120 mm,  Distance between bearings - 1260 mm,  Height of the drum axis - 860 mm,  Operating capacity - 600 dm3,  Weight of the machine - 641 kg,  Installed power - 5.5 kW,  Input voltage/frequency - 400V/50Hz,  Connector - 32A; 400 V  Milling time range - 1s... 99h59min,  Mill installed on a steel frame,  Drum made of 10 mm steel without inner lining. including first filling 80 mm steel balls Technical specification:  Dimensions - 1300 x 1560 x 1210 mm, (with drive and control cabinet installed)  Dimensions of the packed machine - 1500 x 1800 x 1320 mm,  Mill drum external dimensions - Ø870 x 1120 mm, � ...

AVIAN Engineering Model G46/ 60 Pinch Infeed Rollers Integral Blower Main Motor 20 kW Blower Motor 2 kW Rotary Blade 6pcs Stationary Blade 4pcs ThruPut 300 KG/H Cutting Chamber 620 x 460mm Hopper Opening 620 x 500mm

No.: 851275 with speed-controlled feed pump Funnel in Exx protection with switchgear good condition Dimensions LWH: 700 x 700 x 700 mm Weight: approx. 100 kg

No.: 56218 Power: 4 kW with hose pump and control cabinet highly specified, as good as new

Mikron Milling Machine WF2/35 - Width: 120 cm - Depth: 140 cm - Height: 180 cm Good condition, fully functional, can be viewed and tried out on site. Shipping also abroad. Sightseeing: Basically, I would like to point out that the article can be viewed and tested under power before purchase in order to rule out misunderstandings. Please ask questions before purchasing to avoid confusion. If you have any general questions or would like to make an appointment for a viewing, I can be reached at any time on the telephone number below or above. Errors in the description and prior sale excepted. VAT is shown separately on my invoices. Shipping with forwarding agent.

Blade length 205 mm Max cutting performance Sheet R = 42 kg / mm2 4 mm Sheet R = 70 kg / mm2 3 mm Engine power 3 kW Number of beats / minutes 50 min Table dimension 625 x 954 mm Capacity of the oil tank 25 l Weight 500 kg The setting between the blades is fully automatic. Standard: - 1 set of knives at 30 ° (mounted on the machine) - 1 stop switch - 1 general circuit breaker - 1 stop adjustable and adjustable every 15° - Fill the first oil - Manual with installation and maintenance instructions and service keys.

XYZ SMX 5000 CNC bed milling machine was built in 2016 in the UK. The machine for precision machining of workpieces with a maximum weight of 850 kg is made from a uniform cast iron, which guarantees excellent rigidity and stability during even the most intensive machining. The enclosed workspace includes a large work table with a length of 1930 mm and a width of 355 mm, a reliable spindle and a tilting work head. All this is complemented by a CNC control with integrated CAD functions, which significantly simplifies everyday machining. The XYZ Machine Tools SMX 5000 CNC milling machine weighs 3570 kg. Technical specifications of the XYZ SMX 5000 milling machine - feed in the X/Y/Z axis: 1500/600/580 mm - rapid traverse in X,Y,Z axis (CNC): 6.3 m/min - rapid traverse in X,Y,Z axis: 3.8 m/min - work table dimensions (L x W): 1930 x 355 mm - maximum workpiece weight: 850 kg - number ...

ATMSolutions ATMS 1325 CNC milling machine built in 2017 in Poland is designed for the production of both small and large parts made of e.g. aluminium, plastic or wood. The machine on offer is like new, it has never worked after a trial run. The machining process is performed on a large vacuum table using a powerful, water-cooled spindle. The steel frame, by increasing the overall rigidity, makes it possible to achieve unprecedented precision and accuracy in machining, removing any vibration and deformation. In addition, the X and Y axes are equipped with trapezoidal guides with gear drives with bevel teeth, thanks to which excellent dynamics and feed repeatability are achieved. This is complemented by an intuitive CNC control with professional CAM software that supports G-CODE and .nc commands. The ATMS 1325 CNC milling machine weighs 1000 kg. Technical specifications of the ATMSo ...