veneer used for sale

On request

HOT PRESS MODEL PL 90s 3000x1300 mm PS VBO TECHNICAL CHARACTERISTICS Platens dimensions 3000x1300 mm Stroke 400 mm Type of stroke Upstroke design (from bottom to top) Type of platen Assembled platens with coil and aluminum covering Total thrust 90 ton on 80% of the surface Pressing Cylinders N° 6 cylinders ø70 mm Specific Pressure 2.05 kg/cm2 on 100% of the surface 2.56 kg/cm2 on 80% of the surface Loading and Unloading Side3000 mm side Type of Heating system Oil boiler ? maximum temperature = 120°C Heating system specificationsElectric boiler 18 kW Opening Automatic by timer Control Board Standard Power supply 400V, 50Hz, 3ph Security device Safety rope around the press Red emergency Button Two Hand control Norma ...

Plate dimensions: 2500,1250 mm Daylight opening: 400 mm Number of daylights: 1 St. Specific pressure: 2,2 kg/cm² Motor output: 2,2 kW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

I sell the veneer assembly machine KUPER FLI. Built in 2007. Very good condition. Available the same.

Basic machine complete with: - circular saw unit 2,2 kW (3 hp) with pneumatic height adjustment - Axial mechanical adjustment of the saw, adjustment field stepless from 0 to 2 mm - high-precision double ball bearing slides for the moving parts - pressure beam controlled by two lateral pneumatic cylinders, equipped with torsion bar - plastic cable chain - connecting piece Ø 120 mm - HM- saw blade Ø 180 mm - Lubrication unit with filter complete with gearbox and pressure gauge on the air line - service tools - safety devices type: FILA 31 Usable cutting length 3.100 mm type: FILA 37 Usable cutting length 3.700mm type: FILA 43 Usable cutting length 4.300mm

Veneer press Brand: ORMA Type: NPC/DIGIT 6/90 New machine Technical datas: Press area: 2500x1300 mm Amount cylinder: 6 Lift & max. press opening: 400 mm Total pressure: 90t Electro-heater 18 kW for thermo-oil (up to 120°C) Optional: - Aluminium coating - 650 mm stroke - Parallelism control by sensor - Extra charge for down stroke design - Extra charge for temperature up to 150°C - Extra charge for temperature up to 200°C - Mylar protection foil 350,00 ? per panel - Pressure plate covered with glass fiber fabric Teflon - Hardware for Industry 4.0

Hot press Make: ORMA Type: NPC/DIGIT 6/95 New machine Technical datas: Press area: 3000x1300 mm Amount cylinder: 6 Lift & max. press opening: 400 mm Total pressure: 90t Electro-heater 18 kW for thermo-oil (120°C) Optional: - Aluminium coating for panels - 650 mm stroke - Parallelism control by sensor - Extra charge for down stroke design - 4 side loading - Max. temperature up to 150°C - Max. temperature up to 200°C - Mylar protection foil - Pressure plate covered with glass fier fabric Teflon - Hardware for Industry 4.0

New longitudinal veneer splicer Brand: CASATI Type: LINEA 1250 Technical details: Arm length 1.250 mm Veneer thickness 0,4 - 4 mm Min. veneer length 350 mm Min. veneer width 45 mm Glue for pre-gluing: Urea and PVA Glue for integrated gluing: Urea Feed speed 10 - 40 m/min. Heating area length 1.250 mm Total connected load 7,4 kW Power consumtion approx. 6 kw Compressed air consumption 5 Nl/min Compressed air pressure 6 - 8 bar This machine permits the longitudinal splicing of veneer sheets by applying glue on their edge. Immediately afterwards the veneer will be passing through a heated zone in order to activate the glue reaction: the glue will be hardening thus bonding the veneer sheets. The integrated glueing device allows the joining by one only process. Its also possible to bond pre-glued veneer sheets Option for an extra charge: Cooling device for the glue po ...

Veneer jointing guillotine, hydraulic Brand: Casati Type: TO/CC 3600 New machine Technical data: Cutting length: 3.600 mm Daylight opening of the clamping beam: 100 mm Max. rear feed width 800 mm Min. rear feed width 25 mm Hydraulic unit motor power 10 PS Rear feed motor power 0,5 PS Equipped with: - Motordriven feed of the back fence - Cutting edge light - Millimeter counter - Manual and automatic working cycle. The operator can choose between: manual working cycle (separated controls for each phase of the working cycle) or automatic working cycle (one only push-button control for the whole cycle) - hydraulic control valve of speed and pressure of knife beam and clamping beam - central system of lubrication - knife made with special steel - angular fence - Photocells and guards as per EC rules Options for an extra charge - Photo cells and guards ...

Basic machine complete with: - with automatic feed - circular saw unit 2,2 kW (3 hp) with pneumatic height adjustment - Axial mechanical adjustment of the saw, adjustment field stepless from 0 to 2 mm - high-precision double ball bearing slides for the moving parts - pressure beam controlled by two lateral pneumatic cylinders, equipped with torsion bar - plastic cable chain - connecting piece Ø 120 mm - HM- saw blade Ø 180 mm - Lubrication unit with filter complete with gearbox and pressure gauge on the air line - service tools - safety devices type: FILA 31 Usable cutting length 3.100 mm type: FILA 37 Usable cutting length 3.700mm type: FILA 43 Usable cutting length 4.300mm

Manufacturer: Simmpianti, Year: 1998, Longitudinal through running press: yes, Stages: 1, Work piece width min-max mm: 2700 mm X 3200 mm, Min.-max. workpiece height in mm: 3-80, Press length mm: 3200, Pressing width mm: 2700, Press power kg /cm²: 4-6, Warmwasser beheizt: yes, Feeding: yes, Automatical glue supply: yes, Veneer applicaition table: yes, Through running machine: yes, Destacking: yes, Year :1998

Manufacturer: Fischer Rückle, Type: Cut Master, Year: 2007, Control: Fischer Rückel, Cross cutting guillotine: Qeurschneidanlage und Verbindungsmaschine, Cutting lenght mm: 250-2800, Working hight mm: ca.1,5, Digital readout lineal guide: yes, FREE TEXT: verlleimung über Fadensystem, Year :2007

Manufacturer: Fischer Rückle, Type: FZK, Year: 1998, Working width mm: 1200, Veneer thickness min mm: 0,5, Veneer thickness max. min: 1,6, Feeding speed max m/min: 10-60, Feeding speed continous adjustable: yes, White glue connection: yes, Blue cooling: yes, Total power kW: ca.10, Wight approx. kg: 1500, Year :1998

Manufacturer: Langzauner, Type: FPS Hydromatik, Control: yes, Longitudinal cutting guillotine: yes, Cutting lenght mm: 3100, Schnittbreite min-max mm: 600, Working hight mm: 50, Required space L x W x H mm: 3900x1170x1500, Wight approx. kg: 3200,

Manufacturer: Hymmen, Type: AS 260, Year: 1973, Longitudinal cutting guillotine: yes, Double knife: no, Cutting lenght mm: 2.600, Motor-driven kinfe beam: yes, Year :1973

Manufacturer: Tagliabue, Type: L 600, Year: 1998, Monting of the machine: Walze/Walze, Sanding width mm: 600, Sanding hight mm: 0,5-30, Number of sanding belts: 2, Continous adjustable feeding speed m/min: 5-20, Feeding engine kw: ca.2, Sanding belt dimensions: ca.2620 X 630, Sanding belt speed m/sec: 2 Stufig, Power belt 1 in kW: ca12, Performance in kW belt 2: ca.12, Constant table hight: yes, machine ready for demonstration: yes, Year :1998

Manufacturer: Weber, Type: K 1-1100 V, Year: 2001, Monting of the machine: Walze, Double sided sanding line: no, Sanding width mm: 900, Sanding hight mm: 100, Number of sanding belts: 1, Continous adjustable feeding speed m/min: 2 - 14, Feeding engine kw: 1,3, Sanding belt dimensions: 2.620 x 1.150, Table hight adjustment by engine: no, Rollers: 1, Power belt 1 in kW: 15, Intermediate sanding of lacquer: no, Vacuum table: 2,2, Noise enclosure: yes, Brushing unit: 0,55 kW, Year :2001

Manufacturer: Jsting , Type: PFS 1800, Year: 1964, Longitudinal cutting guillotine: yes, Pressbalkenöffung mm: ca.80, Cutting lenght mm: 1800, Schnittbreite min-max mm: 850, Working hight mm: ca.40, Alignment light: yes, Digital readout lineal guide: yes, Motor-driven kinfe beam: yes, Motorized stop adjustment mm: yes, Year :1964

Manufacturer: Josting , Type: EFS, Year: 1968, Control: hand, Longitudinal cutting guillotine: yes, Pressbalkenöffung mm: 60, Cutting lenght mm: 2800, Schnittbreite min-max mm: 500, Working hight mm: 30, Alignment light: yes, Digital readout lineal guide: yes, Motor-driven kinfe beam: yes, Motorized stop adjustment mm: yes, Knife drive: Elektro, Year :1968

Manufacturer: Fischer Rückle, Type: Omnimaster, Year: 2006, Working width mm: 1200, Veneer thickness min mm: 0,5, Veneer thickness max. min: 1,6, Feeding speed max m/min: 10-60, Feeding speed continous adjustable: yes, White glue connection: yes, Blue cooling: yes, Total power kW: ca.10, Wight approx. kg: 1500, Year :2006

Manufacturer: Fischer Rückle, Type: Omnimaster, Year: 2007, Working width mm: 1200, Veneer thickness min mm: 0,5, Veneer thickness max. min: 1,6, Feeding speed max m/min: 10-60, Feeding speed continous adjustable: yes, Thread heating: yes, Total power kW: yes, Wight approx. kg: ca.10, Required space L x W x H mm: 1500, Year :2007

Manufacturer: Fischer Rückle, Type: AFD, Year: 2007, Control: Programm, Double knife: yes, Cutting lenght mm: 4200, Working hight mm: 40, Alignment light: yes, Digital readout lineal guide: yes, Motorische Anschlagverstellung mm: automatisch, Hydraulically driven kinfe beam: yes, Pressure beam: yes, Wight approx. kg: 10000, machine ready for demonstration: yes, Year :2007

Manufacturer: Kleistronik, Type: KT 96000 Funiermessanlage, Year: 2005, Programm: Auswertungssoftware für Funierpakete, Funierparketvermessung: yes, Barcodedrucker: yes, Einlaufband: yes, Scanner: yes, Auslaufband : yes, Feeding speed m/min: 60, Software Auswertung: yes, Flächenermittlung: yes, Schnittstelle SAP: yes, Wight approx. kg: 500, Year :2005

-) Press surface: 3,100 x 1,600 mm -) Cylinder: 8 cylinders -) Floors: 5 floors, 6 heating plates -) Heating plates: drilled 40mm steel heating plates -) Heating: for hot water or thermal oil (up to 200° -) Press opening: up to 600 mm -) Cooling: with own unit Etc.

HYDRAULIC PRESS with hot platens model ITALPRESSE SCF 6 second hand machine for wood, veneer, composite materials, furniture, panels etc platen useful size mm.3000 x 1300 n.06 cylinders diam.mm.70 max. thrust Ton. 120 opening mm. 400 hydraulic pump motor power Hp 3 hot water plates heating via wood boiler weight kgs. 4500 volt. 380/50

thread splicer machine for veneer model KUPER FW 1150 second hand machine volt. 380/50

SPECIFICATIONS: Working width: 420 mm Feed speed: 6 m/min Voltage: 230 V

Cutting length: 3100mm, machine dimensions X/Y/Z: approx. 4800mm/1200mm/1300mm, weight: approx. 800kg. An on-site inspection is possible.

Electricity connection 400V 13kW 2 heating plates à 1200 x 2250 mm Heating plates controlled by 2 thermostats Press pressure at 250 bar LxDxH: 2590 x 1330 x 1950 mm Weight approx. 2800 kg Press thickness 380 mm

A veneer line Cremona is available. 1) Vertical cutter Cremona, year of manufacture: 1999, working width: 5400mm. Includes lifting device. 2) Dryer Cremona, year of manufacture: 1999, control: Siemens PLC, control year: 2019, working width: 5400mm, vacuum feed width: 5400mm, sections: 6, temperature zones: 2, cooling section: 1. Production capacity: approx. 70 sheets/min. Documentation available. An on-site inspection is possible.

Dimensions (L/W/H): 4500x1500x2000 mm Weight: 6500 kg Total power requirement: 2 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Code: 0223 Brand: ITALPRESSE Model: PHF Hydraulic press for curved veneers for processing seats, chair backs, benches, tables and other curved items Technical data: Platen dimensions mm 2600 x 1600 Opening between platens mm 1500 Thrust ton 100 Movement from bottom to top Motor power Hp 4

Dimensions (L/W/H): 2960x1500x2000 mm Weight: 4000 kg Total power requirement: 19,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Code: 0487 Brand: KUPER Model: 630 Thread splicer for veneer with base Technical data: Throat depth mm 630 Thickness of veneers 0,4 - 2 mm Feed speed 7 mt/min Volt 220 single-phase Overall dimensions : mm 950 x 500 x 1180 h Weight kg 95

Dimensions (L/W/H): 3940x1620x2130 mm Weight: 5760 kg Total power requirement: 32,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 3600x1650x2150 mm Weight: 6500 kg Total power requirement: 52 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Simimpianti 3500×1300 veneer shelf press Shelf length 3500mm Shelf width 1300mm Two Batches Press on 8 cylinders Shelves heated with CO water Operating pressure max 300bar Piston diameter 80mm Machine Weight 7000kg Machine dimensions 435x160x235cmH Net price 65,000zł

Dimensions (L/W/H): 4500x1500x2000 mm Weight: 6500 kg Total power requirement: 22,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 3480x1500x2000 mm Weight: 5500 kg Total power requirement: 22,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 5200x1650x2250 mm Weight: 9000 kg Total power requirement: 45 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 3980x1500x2000 mm Weight: 6000 kg Total power requirement: 22,5 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 3480x1500x2000 mm Weight: 5500 kg Total power requirement: 2 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 3750x1650x1970 mm Weight: 5000 kg Total power requirement: 6 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 3450x1550x2950 mm Weight: 4500 kg Total power requirement: 1,6 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 4450x1550x2950 mm Weight: 4800 kg Total power requirement: 1,6 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 4300x1650x2520 mm Weight: 7900 kg Total power requirement: 108 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Plate dimensions: 3000x1350 mm Daylight opening: 400 mm Number of daylights: 1 St. Heating: 31,5 kW Specific pressure: 2,5-5,0 kg/cm² Total pressure: 90 t Motor output: 1,5 kW Dimensions (L/W/H): 3480x1500x2000 mm weight of the machine ca.: 5000 kg Year: Year: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 4200x1650x2150 mm Weight: 7500 kg Total power requirement: 54 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 2950x1550x2950 mm Weight: 4000 kg Total power requirement: 1,6 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.