two used for sale

The machine is formed of the following main assemblies: floor table, left and right beds, gantry assembly (a saddle and a column on the each bed , a cross-rail, and a cross beam ) and two milling heads. The gantry is guided by the slideways of the two beds and the cross rail is guided by the slideways of the two columns. The milling heads travel on the cross rail guideways. Inside of the each milling head is guided a ram with the main spindle. Fixed table length 36 000 mm Fixed table width 6 000 mm Distance between columns with covers / without covers 6 900 / 7 100 mm Gantry travel 30 000 mm Cross rail travel 3 100 mm Milling heads (right and left) travel on cross rail 7 400 mm Vertical travel of right and left rams 1 000 mm Gantry work feeds 0 - 6 000 mm/min Gantry rapid feed 10 000 mm/min Milling heads (right and left) work feeds 0 - 3 000 mm/min Milling heads (right and l ...

TWIN – CNC PUNCHING LINE EQUIPPED WITH 2 HORIZONTAL HEADS 22 TONS Punching machine “Twin” is equipped with feeders that move and place the tubes according to a punching program set on the programmer. Twin can punch either a row, or two rows of holes on the same tube at the same time, it is equipped with a rotary vice for round tubes, it can punch different rows of holes on the same tube. It has been supplied with two heads; this way, either square or rectangular tubes can be punched on all 4 sides in a single run in the machine, according to the tools installed, it can punch either one or two tubes at the same time. Excellent Condition.

The sale is intended for the entire brewery in the body, only and exclusively in the body. Steamed room from two 15hl semi automatic vats Ecobrewtech Touchscreen system control panel with recipe programming Very high precision electronic fiscal meter Cold (glycol) and hot (steam) storage tank of 30hl each. Double stage heat exchanger (cold water and direct glycol) 158hl cellar (2 45hl fermenters, 1 24hl fermenter, 1 29hl fermenter and 1 15hl fermenter) Steam generator year 2020 of 150kg / hour with pressure reducer (low pressure work but also high if necessary) Softener Chiller year 2020 from 23kw Manual 4-jaw isobaric bottling machine, July 2021 Cold room about 30sqm year 2020 Wheeled pump for washing year 2020 Product transfer tubes 2020 Skid 2 pumps for glycol and glycol tank 500lt 2 stainless steel control panels for fermenters control (total 10 slots, 7 active therm ...

Biosan microplate washer. Scrubber purchased in 2017, efficient, not used, turned on once to check if it works. The Inteliwasher 3D-IW8 microplate washer is designed to wash a variety of standard 96-well microplates, split plates such as Flat Bottom, U-shaped and V-shaped FastFrame (rectangular well) microarrays. The washer is a fully programmable device to perform multi-stage work. It operates in a single point in a hole, two points in a hole or cyclically (in a circular or rectangular path), liquid dispensing mode, and washing and rinsing mode (in cycles of both functions). The fluid dosing system allows dosing each of the three independent channels for buffers separately. The 4-CHW recorder connected to the washer provides automatic control of the volume of washing solutions and beakers. Shows the volume of reagent in each bottle (in percent) and alerts you when the fluid is runn ...

Slotted hole drilling machine with pneumatic height adjustment Duggle hole drilling on two levels in one clamping Motor power 1.5 kW With Röhm two-jaw chuck 1 - 20mm Pneumatic adjustment of the machining height by foot pedal, dowels on two levels without repositioning. Transverse adjustment approx. 240mm, infinitely variable or in 16/22/25/32mm increments Maximum height adjustment approx. 135mm Drilling stroke approx. 145mm Table size approx. 700 x 380mm pneumatic workpiece clamp Fixed stop and adjustable angle stop from +45 to -45 degrees Grid rail for quick adjustment on the side of the grid Driving equipment Extraction connection Parts repainted Pressure reducer renewed Dimensions approx. 950 x 1200 x 1300mm (LxWxH), weight 320kg. The machine can be demonstrated by appointment at our site. We only offer machines that are ready for demonstration in our warehouse ...

Air Compressor Atelier Francois CE24A, 510 Nm3/h at 40 bar This three-stage intercooled high pressure compressor was manufactured in year 2008 and the operation was stopped in year 2019 and it was afterwards professionally dismantled. This compressor is very slow speed and it has only two cross-head assemblies, two connecting rods and associated bearings. There is no piston rod packing on 3rd stage, which eliminate sealing against 40 bar. Single acting 2nd and 3rd stage, requiring few valves. Smaller 2nd and 3rd stages are horizontal position to optimize the piston ring life. The delivery includes • AF CE24A high pressure air compressor with electric drive mounted on common base frame • Air-cooled stainless steel 40 bar air dyer with integrated 1-micron filter, dew point alarm and Bekomat drain system, made by Hankison • Horizontal 300 litre hot galvanized 40 bar air re ...

Scheugenpflug DOS P016 Piston Feeder Piston dosing system DOS P for a wide range of requirements The piston dosing systems from Scheugenpflug work according to the principle of volumetric dosing, i.e. the dosed amount of material is mechanically determined by the geometry and stroke of the associated cylinders. The cylinder is filled with the potting material by feeding it from the corresponding material conveyor system. If a two-component medium is used, the volume of the two cylinders simultaneously determines the ratio of the resin and hardener components to each other. The dosing pistons simultaneously push the two components in separate channels towards the exhaust valve, where they only mix in the static mixing tube to form a homogeneous reactive medium. The Dos P016 / 050 / 100 / 300 / TCA piston dosing systems are high-precision volumetric dosing systems designed for pr ...

Used Simonazzi Europa Isobaric Monoblock 48 8 8 Suitable for the production of beer sparkling wine soft drinks both carbonated and non carbonated and mineral water in glass containers with a height of 130mm to 350 mm The monobloc is composed of a filling carousel of 48 Simonazzi Eurostar model taps with completely new pre evacuation vacuum self levelling and relative snift the bell rods are electropolished for perfect sliding and a very long life Flling system of Used Simonazzi Europa Isobaric Monoblock The sniff is equipped with a double seal to use the taps for both carbonated and non carbonated There is a vacuum pump with a water cooled ring The filling bell is tested for 7 Bar of pressure and is internally mirror electropolished with an internal inclination for maximum sanitization The 48 pistons are completely new in stainless steel and also the sliding bars and bearings are new and ...

01 Product to be filled CSD 02 Type of Bottle RoundBottles 03 M O C of the Bottle PET Bottles 04 Fill Volume Bottle sizes 500ml 05 Type of Caps Screw Caps 06 Type of Labels BOPP 07 Output required 416 Bottles Per Minute on 500 ml BLOWER SIPA 16 CAVITIES 2007 WITH MAINTENNACE OPERATION Used blow molding machine for PET bottles with production capacity up to 25 000 bph with the 500ml format Year of construction 2007 Used blower complete with Octagon tipper Air recovery system preform hopper This machine is immediately available for sale and in case of request we can carry out pre production maintenance Detached from production in fully functional status is excellent opportunity for used equipment We will build new neck personalization for pco 1881 We will build two new set of blow mould as per your request Air conveyor system NEW used revised 2024 NEW RINSER FILLER SCREW CAPPER SPORT CAPPE ...

Digitaldruckmaschine - Digital Printing Machine HP Indigo 5500   Year 2007 - Serial-No. 30005331   Printing speed 68 4-color 8.5 x 11 in images per minute (two-up); 136 2-color and 8.5 x 11 in images per minute (two-up)  Image resolution 812 dpi at 8 bit, 812 x 1624 dpi in High Definition Imaging  Line screens 144, 160, 175, 180, 230 lpi  Paper format 13 x 19 in maximum  Image format 12.12 x 17.7 in  Paper weight Coated: 55 lb text - 130 lb; Uncoated: 40 lb text - 120 lb;   Thickness: 3-16 pt  Paper input system • Two drawers with 7 in depth each each (1800 sheets of 3-16 pt)  • A total of 3600 sheets of 80 lb. text.  • All paper drawers support the full range of substrates   Paper output system • Autoduplex/autoperfecting standard  • Main stacking tray with 23.6 in stack height with job offset stacking  ...

Used complete isobaric filling line Krones up to 32 000 bph Significantly the Used complete isobaric filling line Krones up to 32 000 BPH is a technologically advanced line Specifically it s designed for PET filling with water both still and carbonated and soft drinks CSD Impressively this used isobaric filling line offers an impressive capacity of up to 32 000 bottles per hour BPH combining efficiency and precision in the bottling process Main Component KHS Blomax Blower Central to the line is the KHS Blomax 18 blower achieving a maximum productivity of 32 000 B H Included in the equipment are a preform silo elevator and unscrambler plus an air recovery system Additionally a new touch HMI Human Machine Interface has been installed and the machine has been completely overhauled It has been adapted to work with a single type of neck preform e g 1L 30gr Preform PCO1881 and comes with a set ...

HEIBER & SCHROUDER Model: CE 850 Year: 1999 Blank length: min 100 mm Width of the blank with 4 glue points 600 mm (1 track)/ 347 mm (2 tracks) Width of the blank with 8 glue points 500 mm (1 track)/ 347 mm (2 tracks) Materials c cardboard from 200 g/m² upwards, microwave Description Conical/clamshell box forming machine Fire HEIBER & SCHRODER Model – CE850-2 two-track Machine with 850 mm clearance, two plates, two forming towers, 8 glue points

Technical data for the packing table: Manufacturer: Stow Type: Pal Rack NS Basic: Total width: approx. 1,550 mm Total depth: approx. 1,000/400 mm Total height: approx. 2,000 mm Number of levels (1,000 mm deep): 02 pcs. Number of levels ( 400 mm deep): 02 pcs. Working height: approx. 938 mm The scope of delivery includes: 02x Shelf stand, used Material colour: light blue Frame profile: PNFB12 Profile dimensions: 85 x 65 x 1.75 mm Stand height: 2,000 mm Stand depth: 1,000/400 mm Incl. cross and diagonal struts, foot plates The stands are pre-assembled ( bolted truss ) 02x Footplates, new Material color: blue Total width: approx. 100 mm Total depth: approx. 110 mm 08x Shelf trusses, used Material color: orange Truss Type: PNBH0488 Box profile: 80 x 50 mm Clear width: 1,350 mm 16x Locking pins, used Finish: sendzimir g ...

Technical data for the packing table: Manufacturer: Stow Type: Pal Rack NS Basic: Total width: approx. 1,550 mm Total depth: approx. 1,000/400 mm Total height: approx. 2,000 mm Number of levels (1,000 mm deep): 02 pcs. Number of levels ( 400 mm deep): 02 pcs. Working height: approx. 938 mm The scope of delivery includes: 02x Shelf stand, used Material colour: light blue Frame profile: PNFB12 Profile dimensions: 85 x 65 x 1.75 mm Stand height: 2,000 mm Stand depth: 1,000/400 mm Incl. cross and diagonal struts, foot plates The stands are pre-assembled ( bolted truss ) 02x Footplates, new Material color: blue Total width: approx. 100 mm Total depth: approx. 110 mm 08x Shelf trusses, used Material color: orange Truss Type: PNBH0488 Box profile: 80 x 50 mm Clear width: 1,350 mm 16x Locking pins, used Finish: sendzimi ...

Chiller made by Linde Self-made for low temperatures, goes down to minus -25 °C, with two refrigeration circuits. With two Bitzer 6G-30.2Y compressors as main compressor and two 2N-7.2Y compressors as subcoolers. Bundle tube heat exchangers, condensers, etc. Compressors have been renewed.

track width 440 mm cutting height 55 mm - 200 mm disc diameter 320 mm 2 x 75 kW main engines 3 kW feed motor feed speed adjustable on the inverter up to 60 m / min the top five pinch rollers lower auxiliary roller five rows of pawls electric cutting height adjustment electric shaft height adjustment automatic central lubrication rollers diameter 60 mm, wedge 18 mm sleeve diameter 80 mm wedge 13 mm sleeve length 440 mm spigot diameter 200 mm transport dimensions (length / width / height) 280/245/230 cm weight 5120 kg Multirip saws are machines used in the wood industry mainly for cutting piles, but not only. Machines of this type can cut boards into smaller elements and cut lamellas. The principle of their operation is very simple, the machine has a spindle located in a central point on the horizontal axis, on which tools in the form of discs are installed. Depend ...

cutting width 380 mm cutting height 165 mm disc diameter 300 mm four upper pulling years pneumatic pressure of rollers four lower pull rollers two rows of pawls spindle diameter 70 mm spindle speed 3640 rpm 2 x 55 kW main engine total power 114 kW 550 mm horizontal clearance dimensions of the machine (length / width / height) 220/180/220 cm weight 2940 kg The multi-blade saw is designed for longitudinal cutting of wood with a set of circular saws. It is used for cutting piles into boards in the packaging program, garden program, etc. In this machine, cutting the material is carried out by means of a set of saws mounted on two spindles parallel to each other. The spindles are mounted in a sliding headstock ensuring even load, swimming and wear of the saws after the adjustment. The piles are transported inside the machine by four driven pairs of rollers. The pressing force ...

Multisaw ZLT 500 edger with 500/120 feeders – Czech production – a movable shield with the possibility of installing several shields cutting width 500 mm cutting height 120 mm min. material length 800 mm max. disc diameter 450 mm one disc movable sleeve 70 mm fixed sleeve length 100 mm engine power 45 kW two upper pressing rollers four lower pulling ones feed smoothly adjustable on the inverter shaft support two rows of pawls max material width 700 mm length of feed rollers 3000 mm roll width 700 mm roll diameter 70 mm receiving table 6200 mm chain width 60mm seven pressure rollers two bottom pull rollers transport dimensions (length / width / height) 700 / 245 / 180 cm weight 3000 kg

Multisaw Edger ZLT 500 with feeders 500/140 - Czech production - a movable target TECHNICAL PARAMETERS: cutting width 500 mm cutting height 140 mm min. material length 800 mm max. blade diameter 450 mm one movable target engine power 30 kW four lower pulling shafts two upper pressure shafts feed smoothly regulated on the inverter shaft steady two rows of pawls feed rolls 4 pieces roll length 600 mm roll width 450 mm roll diameter 70 mm receiving table 6200 mm chain width 60 mm seven pressure rollers two lower pulling rollers transport dimensions (length / width / height) 700/245/180 cm weight 3000 kg

Multisaw Edger two floating discs Raimann KS 310 BV - year of manufacture 1995 - German production - DTR - automatic spacing of discs with the possibility of programming - two movable discs TECHNICAL PARAMETERS: - track width 340 mm - cutting height max 120 mm - engine power 30 kW - disc diameters 250/360 mm - Possibility to put on a shoe - electric height adjustment - feed continuously adjustable 11-38 m / min - power of the feed motor 1.5 kW - two movable discs - possibility to program 10 dimensions per disc - control 69 P22 - three lasers - max element width 1000 mm - minimum element length 600 mm with a shoe 400 mm - four upper pressure rollers - spindle diameter 65 mm - sleeve diameter 80 mm - spigot diameter 250 mm Dimensions 230x220x230 weight 2500 kg

Four-side planer KUPFERMUHLE 600x200mm - after technical review - German production - PLANING HEIGHT ON TWO AND FOUR-SIDES 200 mm - ideal for wet wood - electric height adjustment - electric adjustment of the left head - double feed chain planing width 600 mm planing height on two and four sides 200 mm power of vertical spindle motors 2 x 8.6 kW motor power of the lower shaft 5.5 kW upper shaft motor power 7.5 kW guiding ruler electric height adjustment adjustable vertical heads four upper pulling rollers four lower pulling rollers two take-up pull rollers 4 knives per shaft diameter of shafts 150 mm six types of feed speed 7 / 9 / 11.5 / 14 / 18 / 23 m/min row of anti-recoil pawls spindle diameter 30 mm / 100 mm material pressure at the left head dimensions (length/width/height) 260 x 190 x 205 cm weight 3500 kg

- Folding and gluing machine - Supply voltage(V): 400 - Auxiliary voltage (Vdc): 24 - Frequency (Hz): 50 - Power (kW): 3 - Power of gluing system (kW): 5,8 - Machine length (mm): 6175 - Machine width (mm): 1576 - Machine height (mm): 1580 - Minimum die cut format (mm): 120x120 - Maximum die cut format (mm): 720x1020 - Full automatic continuous feeder - Folder flap group with hot melt gluing system - Folding tools with automatic transport devices - Paper transport system with adjustable pressure - Automatic delivery table - 1 double-sided tape applicator – minimum interval between two tapes is 35 mm - Material: paperboard 200-600 g/m2, corrugated cardboard up to 4 mm thickness - Minimum paper weight: 150 g/m2 - Maximum paper weight: 350 g/m2 - Speed of glue application: 100 m/min Designed for production: - Straight-line boxes - Crash-lock bottom boxes - Fol ...

Two-way hydraulic bending machine, with CNC numerical control, with two bending jaws and deflection compensation (bombing). Upper instruments segmented. Year of manufacture 11/2008. These are two separate devices: a) material loading, b) double-sided bending machine with a table for feeding material incl. its rotation options. The machine was put into operation in 2009 and was only used for about half a year. It is possible to buy the bending machine itself, or just with the serving table. Bending capacities: material width: 2,500 mm thickness: max. 8 mm (material up to 400 N/mm2) edges with minimum height = up to 6 times the strength of the board minimum radius = up to 1.5 times the strength of the board.

TECNA 4608N spot welding machine which was built in 2008 in Italy is used for precision welding of two sheets of steel or aluminium with a maximum thickness of 4 mm each. During the machining process, the electrodes heat the workpieces until they reach a plastic state in order to become one inseparable piece after cooling. The adjustment of arm reach and electrode stroke enables adaptation of the machine to the user’s individual production requirements. The 4608N resistance welding machine is equipped with a state-of-the-art TECNA TE90 Mark II microprocessor controller, designed to ensure a smooth and uninterrupted welding process. The control system enables the programming of 12 different process parameters and control of the SCR thyristor, responsible for regulating the welding current. The offered TECNA spot and projection welding machine also comes with, among others, a set of e ...

Line for filling delicatessen products in plastic trays, consisting of:, Cup filling system, make Waldner, type 12.3, year 2011, 2 lanes (2 different formats) - but it can only be worked in one lane., Format set 1: round cup diameter 100mm (incl. rim) height 80mm and 60mm, Format set 2: Rectangular cup 185mm long 135mm wide (including rim) 35mm deep, The trays are sealed with film from the roll, Roll magazine approx. 500mm long, 400mm wide, Waldner space requirement: approx.: 2,100 m 2,100 mm, Outfeed belt of the Waldner: approx. 1,800 mm, Dosing of liquid and free-flowing components:, The system has two filling heads, which are filled via a pipeline directly from the cooking kettle., The pipeline can be completely pigged., The pigging line and Maso - Sinus pump, type SPS 3, are included in the scope of delivery., Feeding of the multihead weigher by means of two belts:, Tunnel elevator  ...

Manufacturer : Confitrac sprl Model: CDS-161205 Year : 2017 Type: Deodoriser Condition: new, never used. Document : CDS-P&ID-Deo-500-Electrique.pdf Installation consisting of : - A horizontal cylindrical shallow bed deodoriser divided into two horizontal compartments, supported by two supports and offering the possibility to treat either 250 kg in one compartment or 500 kg in two compartments. - A horizontal buffer tank equipped with a product inlet/outlet, vacuum outlet and sight glass. Volume: +/- 460 litres. - 2 shell and tube heat exchangers - 1 electric heater - 2 electric heating resistances - Other equipment: control and dosing valves, flow meter, steam drying ramp, etc. - Electrical cabinet Materials: all parts in contact with the product are made of stainless steel 304L and 316L. Insulation: 100 mm rock wool. Documentation and drawings available.  ...

Year of production: 1986 Serial number: 50 166 N and the machine was overhauled in 2003 with modernization of electrical control. The machine was equipped with a new SIEMENS automatic controller and new SIEMENS drives. GENERAL CHARACTERISTICS OF THE MACHINE The basic feature of the machine is a fixed portal, a sliding table. The portal has a height-adjustable crossbar, which is equipped with one or two vertical headstocks in the VFS 160 design. Furthermore, the portal is equipped with one or two side (horizontal) VFS 160 headstocks. These types of headstocks can be fitted with additional spindle heads, up to 4 pieces available. The clamping surface of the machine consists of two connected clamping tables, which after disconnection can be used individually (only one is always functional). Clamping table Dimensions of 1 table 2 2,000 x 4,000 mm Total length of connect ...

New hot press, hydraulically Brand: ITALPRESSE Type XL/6 30-13 PEA Golden electric heating plate surface anodized to ensure high surface hardness and excellent corrision protection. - Electrical - heating plates: 3000 x 1300 mm - Total pressure: 120 to. - Number of hot plates: 2 pc. - Number of floors: 1 pc. - Stroke: 350 mm - Day light opening: 350 mm - All-round feeding - Number of cylinders: 6 pc. - Diameter of cylinder: 85 mm - Power consumption (hydraulic unit): 3 kW - Electric - combi - heating plates made out of two components: Aluminium - electric - heating plate Iso printing plate - Heating power 22 KW - High pressure isolation plates - Operating temperature: 70 - 90° C. - Max. Temperature: 120° C. - Supply: 400V/50 Hz - Safety accordance with CE standard Standard equipment: - Movement of the press table with rack and pinion parallel guidance at t ...

Motor power 11kW with double pump Control SPS, supported two-hand operation -with a key-operated switch for control voltage / from Cutting force 2 x 20to Feeding channel working width max width 2500 mm loading channel working height = height = 1535 > mm extended knife steel under-sink reinforced, straight version incl. two openings for forklift loading -Colours: Corpus RAL acc. to customers request Cutter bar & grille Ral1028 / melon yellow delivery time: approx. 12-14 weeks Price and photos upon request

Tanks fuel tank fuel tank storage tanks 5 cbm TAnkstelle diesel tank Gas station fuel tank tank tank heating oil tank storage tank 5,000 litres According to DIN 6616/D, above ground, double-walled, incl. officially recognised test certificate. The tank has two saddle feet, a manhole DN 500 with domed lid is used, cleaned, overhauled and is equipped with the following fittings: 1 nozzle with TW closure (filler cap) and dip tube, 1 Sounding pipe provided with dip stick and sounding Rod seal, 1 Vent pipe with vent hood, 1 new limit switch with type approval (AIII), 1 Head and 1 spare socket for harvesting purposes, 1 optical leak display device with type approval and leak fluid. The container is outside new primed and painted. L = 2.70 m + console / D = 1.60 m / weight CA. 1.6 tons. / free charged ex works. On the tank, a pump / nozzle pump is installed on customer's request,  ...

Fully automatic capsule sealing machine. Incl. PLC: Siemens-S5, type: 954, Operating controll: Lauer PCS 095. Format part for capsule size. 3. Output: up to 100'000 capsules/h. Furthermore incl. Visco system TRAWID VM, Sensor O.B.D, Control H, No. 04712479. The controll device is self made (Comp. Wetzel). Gelatin-vessel is A2/ double jacket, heatable with IKA stirrer RW 16- basic incl. agitator OPTI- Color, pump Watson - Marlow 505 S, two forward- and two backward pipe.

Used line for the production of the co-extrusion by PST Forming method. PTI - The twin screw extruder DS 92/28   2x screws with a diameter of 92 mm The length of screws 28 x L / D Snails closed system with internal temperature control, deep nitrided, with degassing on the cylinder, extruder equipped with a vacuum pump with filter, Siemens Servo Motor power: 60 KW Torque: Nm 15700 Screw rotation: 0 - 50 rev. / Min. Zones with ceramic heaters with an intense cooling: 5 x 5 KW Cooling Zones: 4 Performance with hard PVC, depending on the materials and tools: max.600kg / h Length: 4500 mm Width: 1600 mm Height: 2300 mm           Extruder equipped with a microprocessor control SIEMENS type Extrusion Pro Pak visualization 2. Co-Extruder PTI - The twin screw extruder DS 68/28 Snails with a diameter of 2 x 68 mm Length of the screws: 28 x L / D Snails cl ...

The fishing and packing plants have a simple and this stable and torsion-free construction. The machines are characterized by ease of use, flexibility, reliability and low maintenance requirements. The CAMBORIT clip has a capacity of up to 125 packs / min. 1 x 2 bottles can be packed with the CAMBORIT clip. To do this from flat so called "bars" cut to shaped, that get caught under the edge of the bottle. The machine can be operated automatically or manually. Display and operating elements are located on the control panel. All functions are controlled from the control panel and controlled. Errors of the cycle are displayed on the control panel. Action: At the beginning of production the magazine must first cut to be filled. The minimum level is cut to the magazine below, the machine will not turn on. After switching on the machine when existing minimum level of bottles with a capac ...

Used line for packaging of powdery materials in plastic buckets from 2.5 kg to 10 kg. Semi-automatic line of packing and transporting the dispenser weight The line consists of: Two unloading of big bags Oblique conveyor The buffer tank Two batchers Stacking conveyor The set of the transporters with the balance cruise control, feeder lids and closing buckets, made as part of the line for packing powdery materials. The line consists of: Conveyor separator Cruising verified checkweigher Discriminator transporter odstawiaj?cym Conveyor feeder lids Crimper Stacking Conveyor Appetizer - welding machine for bags The checkweigher DWT / xx Technical data: Supply voltage - Uz = 230V Isaiah znamionowy- current = 2-5A (depending on version) Mains frequency - f = 50 Hz overcurrent - F = 10A recommended network layout -TNS Insulation class - I New 2010

Showroom machine Firing furnace powder furnace divisible Romer SLP-90 O D + t convection baking oven Powder furnace new SLS - 90 / O D + t Transit oven divisible Memorized 1400 wide x 2000 height x 6500 depth Dimensions 1920 wide x 2810 height x 6800 depth Electric power supply Rated power 90 kW Voltage 380V Frequency 50-60 Hz Door type: 2 doors on either side - passage oven Anti-ex Castle Warm-up time 15-30 min. (180 ° C) Uniformity & lt; ± 3 ° C, if 180 ° C Max & lt; ± 3 ° C Temperature of 230 ° C Max Transport: selectable Air circulation fan Heaters removable roof heating panels Vertical circulation Fan mounted radially on removable panels Door double two doors on two sides (Durschlaufofen) Divisible Motor 1,1 kW 6480 L capacity Warranty 12 months

Seydelmann AD 114 automatic grinder, 114 mm, almost completely made of solid stainless steel, two speeds on working worm, two speeds on feeding worm, safety grid. The machine is immediately available and you are very welcome to test the machine in Koblenz, Germany.

brand new diesel petrol tank system comprising petrol station fuel tank fuel tank tank system home service station storage tank storage tanks Court gas station steel tank: 1. 10,000-litre tank according to DIN 6616/D, above ground, double-walled 1 pump type eco 55 description containers: New tank, 10,000 litres capacity according to DIN 6616/D, above ground, double-walled, incl. officially recognised test certificate. (Other sizes from 1,000 to 100,000 liters are available on request) The tank has two saddle feet, a manhole with domed lid and is equipped with the following fittings: 1 nozzle with TW closure (filler cap) and dip tube,. 1 sounding pipe provided with dip stick and sounding Rod seal, 1 vent pipe with vent hood, 1 new limit switch with type approval (AIII), 1 head and 1 spare socket for harvesting purposes, 1 optical leak display device with type approval and leak fl ...

The following completely reconditioned and ready compact system of SEPARATORS & SERVICE T.D. is for sale. This selfcleaning separator WSPX 303TGP-71 is clean mainly used water-based coolant, for the concentration of washing liquids like lye also waste water or rain water cleaning. The maximum hydraulic throughput capacity is 1500 l / h. The engine is a two-pole motor with 50 Hz 2.2 kW. The drum has a speed of 9516 RPM 69 DB (A). Control water consumption is 0.5 l / emissions per output. Sediment volume ca: 0.63 liters. Output of min 0.8 liters, max 0.9 litres. The separation is carried out in the separator drum which is driven by the electric motor via a flat belt. The separator can be used as a concentrator with a large heavy phase (E.g. water) and a small stage (E.g., oil), as well as the light phase. The separator can be used as well as cleaning separator (Klarifikator) with o ...

Single column - eccentric press, STANKO, K 1430 A - 100t BJ. 1985 Tech. Condition very good, - pressure: 100 t -Projection: 320 mm -Stroke: 10-130 mm -Mounting height: 400 mm -Table size: 850 x 560 mm x 100 mm -Tappet adjustment: 100 mm -Stroke: 50-53 / per min. -Machine weight: 8800 kg -Dimensions (W x D x H): 1.60 x 1.85 x 2.9 m Camshaft gear ROSS/Herion Herion valve Auxiliary brake DESCH Lutex ZB 200 Two hand release -transverse eccentric shaft and pneumatically actuated clutch / brake Komi nation -suitable for inlays in two-hand operation -secure setting -Single stroke, continuous stroke MOT testing in 04/2016

Metallography Mounting presses ECOPRESS All ECOPRESS presses can be programmed by the user in a simple manner, that the mounting process runs fully automatically. When the ECOPRESS 50, one program can be stored in the control electronics. A rugged bayonet allows quick and safe operation. The ECOPRESS series offers a wide variety of different size of molds of 25 - 50 mm in diameter. At the same time two samples can be embedded per cylinder with an intermediate piston. Alternatively, machine type of ECOPRESS 200 twin-piston for up to at the same time 4 embeds is available. When baked in the samples into plastic granules are melted, that the sample under heat and high pressure wraps pore-free and then through a press cylinder, electronic control, integrated cooling for solidifying. ECOPRESS 50 one cylinder, electronic control, full automatic program ECOPRESS 100 one pressing  ...

Many thanks for your interest on our new Heating/cooling table for chocolate or sugar-, candy dough, please find follow our offer: Heating table / cooling table / working table for sugar or chocolate mass Dimensions (lxbxw) : 1200 x 800 x 800mm / or (lxbxw) : 800 x 600 x 800mm (after customers request we are able to produce other dimensions) Execution completely in stainless steel: folded plates made of stainless steel Standing on 4 feet, (square tube 50 x 50) optional height adjustable with two wheels and two castors water heated, closed system with electr. Thermostat, heat exchanger, circulation pump, safety valve 0.5 bar) Plate heat exchanger technical changes reserved Wir bieten diese Maschine als Neumaschine zum Verkauf an. I offer this machine as New machine

P86 - used appr. 30 m³ / 30,000 litres polyester tank / GRP tank, manufactured by Reich company, aboveground, on two steel bases, in good condition. volume: appr. 30 m³ / 30,000 litres material: polyester / GRP diameter: appr. Ø 3.00 m length: 5.00 m height: 4.30 m including base Storage tank by manufacturer Reich, lying horizontally, aboveground tank on two steel bases, dome on the top of the tank body, multiple connections, in- and outlets, as depicted on the images. The container can be used as a storage tank for many different media such as water, liquid feed or as a rainwater collection tank and much more. Price upon request. Transport can be arranged at low cost. Also we can modify the tank to suit your demands, just ask us. It is not possible to update all our advertisements daily. Since our inventory is changing continuously, it may be that this ta ...

Two-roller gluing machine for the processing of cold glues. Same glue application by changing the distance between the two rollers to each other. width 350 mm. ; ready for use. At this point we allow ourselves to note that all offered machines are in our unrestricted possession or access and are present in our warehouse. Visits and demonstrations are possible on request in our premises. We would also be pleased to inform you about our complete stock, as only part of our portfolio is presented here.

5,000 litre storage containers According to DIN 6616/D, above ground, double-walled, incl. officially recognised test certificate. The tank has two saddle feet, a manhole DN 500 with domed lid, is used, inside empty and professionally cleaned and is equipped with the following fittings: 1 nozzle with TW closure (filler cap) and dip tube,. 1 sounding pipe provided with dip stick and sounding Rod seal, 1 vent pipe with vent hood, 1 new limit switch with type approval (AIII), 1 head and 1 spare socket for harvesting purposes, 1 optical leak display device with type approval and leak fluid. The container is outside new primed and painted. L = 2.80 m / D = 1.60 m / weight CA. 1.3 tons. / free charged ex works. Description PTO pump: Non calibratable type eco-box-55- Capacity up to approx. 55 l / min. suitable for diesel fuel, incl. -Automated fuel dispenser with PC softwa ...

MULTI RIP SAW type CML SCA 320 with rip trimming unit with two circular blades with adjustable interaxle ( one moving saw ) Technical Details : carpet width mm. 320 max. cutting heigth mm. 120 minimum length of pieces mm. 300 blades diameter : min.mm.250 / max.mm.350 maximum distance between two external blades mm. 320 feeding speed mt/min. 0 / 36 motor power Hp 40 net weigth kgs. 2000 volt. 380/50

Shredder, industrial shredder, 2 wave star breakers, glass shredder, rotor scissors, star mill, garbage shredder, two-shaft shredder, two-shaft shredder, shredder with filler for wheel loader used The shredder can also be used as a single position. Manufacturer: SANT'ANDREA NOVARA Type: G30/1570 Built in 2003 Speed of the fast wave: 17.7 rpm Speed of the slow wave 9.3 rpm Turning monent. 11875 Nm Engine VEM 22 kW 400/690 V Dimensions Shredder: approx. 2500 x 1000 x height approx. 400 mm with motor 1500 mm Dimensions of cutting unit approx. 1600 x 810 mm Throw-in height approx. 4.6 m Throw-in funnel approx. 3 x 2 m the drop-in funnel is closed by a percular upward opening slider approx. 2.5 x 1.5 m. Total dimensions of the steel construction: approx. 3 x 2 x 8 m In the shredder, used glass was broken for a foam glass bulking system. Basically, other brittle material ...

Shredder, industrial shredder, 2 wave star breakers, glass shredder, rotor scissors, star mill, garbage shredder, two-shaft shredder, two-shaft shredder, shredder with filler for wheel loader used The shredder can also be used as a single position. Manufacturer: SANT'ANDREA NOVARA Type: G30/1570 Built in 2003 Speed of the fast wave: 17.7 rpm Speed of the slow wave 9.3 rpm Turning monent. 11875 Nm Engine VEM 22 kW 400/690 V Dimensions Shredder: approx. 2500 x 1000 x height approx. 400 mm with motor 1500 mm Dimensions of cutting unit approx. 1600 x 810 mm Throw-in height approx. 4.6 m Throw-in funnel approx. 3 x 2 m the drop-in funnel is closed by a percular upward opening slider approx. 2.5 x 1.5 m. Total dimensions of the steel construction: approx. 3 x 2 x 8 m In the shredder, used glass was broken for a foam glass bulking system. Originally, the recycling of fluo ...

GP115 - used approx. 40 m³ / 40,000 litres polyester tank / GRP-tank, Staffelstein tank, aboveground, lying on two steel pedestals, good condition. capacity: approx. 40 m / 40,000 litres material: polyester / fiberglass length: approx. 6.50 m diameter: Ø approx. 3.00 m height including base: approx. 3.50 m Manufacturer Staffelstein, horizontal, round storage tank on two steel pedestals, access on the front side, multiple connections, in- and outlets as shown in the pictures. The container can be used as a storage tank for many different media such as water, liquid feed et cetera, or as a rain collection tank. Price upon request. Transport can be arranged at low cost. Also we can modify the tank to suit your demands, just ask us. It is not possible to update all our advertisements daily. Since our inventory is changing continuously, it may be that this ta ...

pressure:1000 t stroke:800 mm total power requirement:45 kW weight of the machine ca.:97 t dimensions of the machine ca.:4500 x 4400 x 5300 m Return Capacity:40 t Main Cylinder:(d=500mm) 2 Stück :(140 x 80mm) 2 Stück speed of forward flow:40 - 110 mm/sec Return Speed:150 mm/sec Press speed (infinitely variable via PLC):3 - 12 mm/s Table size:3000 x 2300 x 200 mm Ram plate:3000 x 2300 x 1000 mm demand for oil:ca. 1300 l :210 l/min :600 sec :1500 x 150 mm Hydraulic and mechanical protection of the plunger Two-piece auxiliary motors with 2.2 kw Two-piece auxiliary pumps with a power of 6 L/min. Concurrency monitoring (0.5 mm/m²) Fast forward speed adjustable via plc Maximum deflection of the table at 0, 07mm/m²

pressure:300 t distance between columns:1900 mm stroke:600 mm total power requirement:30 kW weight of the machine ca.:27 t dimensions of the machine ca.:2900 x 3500 x 5400 mm Return Capacity:40 t Main Cylinder:Ø 370 x 350 mm :2 Stk. Ø 80 x 50 mm speed of forward flow:150 mm/sec Return Speed:150 mm/sec Table size:1800 x 1800 x 150 mm Ram plate:1800 x 1800 mm demand for oil:ca. 700 l :max. 900 sec Daylight Opening:900 mm pressure speed:15-8 mm/sec auxiliary motor:5,5 + 2,2 kw auxiliary pump:22 + 5,5 cc Lineal mess stab NOVOTECHNIK:650 mm Table height above ground level (approx.):1000 mm Light sensors front and rear of SICK:900 + 150 mm Monitor:12 Zoll Hydraulic and mechanical protection of the plunger Two-piece auxiliary motors with 2.2 kw Two-piece auxiliary pumps with a power of 6 L/min. Concurrency monitoring (0.5 mm/m²) Fast forward speed adjustable via plc Maximum deflection of the ...