twin column used for sale

Doppelkopfheftmaschine für Broschüren - Twin-headed Stapler for Booklets - Pads Winterling KM17 Year 1986 - Serial-No. 469 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Doppelkopfheftmaschine für Broschüren - Twin-headed Stapler for Booklets - Pads Winterling KM17 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Doppelkopfheftmaschine für Broschüren - Twin-headed Stapler for Booklets - Pads Nagel Multinak S Serial-No. 18093 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Twin-headed Stapler for Booklets - Pads Booklet & block stitcher Nagel Multinak-S (18096) Serial-No. 18096 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Twin-headed Stapler for Booklets - Pads Nagel Multinak Serial-No. 6235-1 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Twin screw extruder APV Baker, int. ref. APV 5 (Baker Perkins) Ø50/25D + additional liner 10D(for 35D), this was totally revamped in 2017, liners and screws are in quite good conditions, reduction gear was replaced in 2021. Operator panel with recipes and 14 heating zones, all in good conditions. Find more here - / Contact us at -

SINGLE MULTIHEAD WEIGHER FEEDING - 2XBAGGERS MACHINES ONLY WITH TWIN OUTFEED CONVEYORS - NO GANTRY ISHIDA MULTIHEAD WEIGHER MODEL: CCW-RS-216B-2D-30-SS YEAR: 2011 16 HEAD ILAPAK TWIN BAGGERS YEAR: 2011 MODEL: VEGATRONIC 500 300MM JAW

Continuous twin-shaft mixer with multi-plate clutch, suitable for vacuum operation. Mixing trough and double cylinder length: 1,500 mm + 500 mm, mixing trough width: 700 mm.

Mixing volume: 450 liters, Two mixed waves with paddles, Stepless speed control, Programmable operation, A spout, mechanically operated, Protective cover of the hopper, including lifting device for standard trolley 200 l, Machine dimensions in mm:, Width: 1,000 mm (1,900 mm with lifting device), Length: 1.800 mm, Height: 2,200mm, Power: 5.5kW, Voltage: 380V, 50Hz, Weight: 1000kg, power: 450 liters per batch, Dimensions / weight: L x W x H: 1,800 x 1,900 x 2,200 mm

MARIS TWIN SCREW EXTRUDER, Loading hopper for regrinds, Barrel with 2 x 92 mm screws 40 L/D, co-rotating parallel screws for polyolefines, CEAR d.c.motor, N.2 vacuum degassing pumps, 4-plate semi-automatic screenchanger, hydraulic pack, Average throughput rate around 1 Ton/h, Water ring pelletizer, drying centrifuge, Electrical control panel, The machine is offered as is or checked

MARIS TWIN SCREW EXTRUDER, Barrel with 2 x 92 mm screws 40 L/D, n.2 vacuum degassing pumps, co-rotating parallel screws for polyolefines, complete with 4-plate semi-automatic screenchanger, hydraulic pack, Average throughput rate around 1 Ton/h, Water ring pelletizer, drying centrifuge, electric cabinet, The machine is offered as is or reconditioned

MARIS TWIN SCREW EXTRUDER, Type TM 85 LC 37 L/D, dosing unit for granulated materials, barrel with 2 x 85 mm co-rotating screws 37 L/D, max screw rpm : 152, vacuum degassing pump 4,5 kw drive, Present capacity 450 kg/h depending on materials and feeding rate, 64 kw drive, Constructed in 1992, offered AS IS or reconditioned, installed power - used power in work: about 60-65% : 64, screws diam.: 85 mm. 37 L/D, screws: co-rotating

Screw Diameter: 140 mm // Throughput: 900 kg/h

Screw Diameter: 92 mm // Throughput: 800 kg/h

Screw Diameter: 130 mm // Throughput: 800 kg/h

Screw Diameter: 58 mm // Throughput: 450 kg/h

Screw Diameter: 50 mm // Throughput: 150 kg/h

Screw Diameter: 64 mm // Throughput: 480 kg/h

Screw Diameter: 27 mm // Throughput: 100 kg/h

A twin screw extruder is offered. Drive: ASEA electric motor type ACA 200-6L, 50.5kW, 1460rpm. Inspection possible by prior arrangement.

Benhil 8358 & 8535 Butter Portion Packer with twin filling/ /Stainless steel hopper / 90 degrees Paper Feed / Capacity Up to 510 pcs per minute, Benhil 8358 Twin Filling Butter Portion Packer, Stations : Paper feed, paper splitting, Paper forming box, Filling , Wrapping, Pressing, outfeed conveyor, semi automatic rotary case Packer . Capacity : 420 -510 pcs per minute depending on Product weight., Fully Refurbished 12 months ago spent over € 200.000, Key Features:, - Portion Control: Benhil packing machines are designed to package butter in accurate, portion-controlled sizes, which is essential for food service operations., - Flexible Options: They often accommodate different types of butter packaging, including mini portions or larger units, catering to various market needs., - Automation: Many of these machines feature automated systems for filling, sealing, and labeling, which helps ...

BANDERA TWIN SCREW PVC PIPES EXTRUDER, for pipes with min/max diam.40/200 mm., extruder with n.2 parallel counter-rotating screws Ø 90 mm, Throghput rate 400 kg/hr, missing of screenchamger (can be added separately), n.2 dies available 40 to 125 mm + 125 to 200 mm., Tooling from 40-200 mm (available diam. 100 mm for O-Ring), Bandera 6 mt.long vacuum calibration tank, IPM haul off unit, IPM saw, IPM belling unit, constructed in 1998, totally refurbished in 2006 by Plasco, machine now disconnected, offered RECONDITIONED., availability: immediate, working width: 40-200 mm Ø, capacity: 400 kg/h, conditions: disconnected, type: pipes extrusion line

This KUHNE KS45-24D compounding extruder was manufactured in 2006. Ideal for processing a variety of materials, it offers robust construction and reliable performance. Consider the opportunity to buy this KUHNE KS45-24D compounding extruder. Contact us for more information.

This LEISTRITZ ZSE60MAXX-48D was manufactured in 2012. A co-rotating twin-screw extruder, its designed for high-performance compounding of advanced polymer materials, including biodegradable polymers. Adaptable to various extrusion processes, its ideal for bioplastics, masterbatch production, or specialty compounding. Contact us for more information about this machine.

The Velati M 2000 twin shaft paddle mixer is a robust and reliable industrial device, specially designed for food processing in commercial kitchens or production facilities. This type of used mixer is characterized by its high capacity and efficiency in mixing a wide variety of ingredients. Thanks to the twin shaft technology, the M 2000 ensures even mixing of the materials while minimizing mixing time. The paddles are designed to ensure optimal mixing without excessive friction, which maintains product quality. The stable construction of the device offers long-lasting performance and lower maintenance requirements. Ideal for use in food processing, this mixer is a valuable addition to any company that requires high-quality and consistent mixes., power: approx.: 1,600 kg mixing volume, Dimensions / weight: Mixer: L x W x H: 4,650 x 1,500 x 1,950 mm, auger: L x W: approx. 5,100 x 2,000 mm ...

Control defective, Dimensions / weight: LxBxH: 2.200 mm x 1.200 mm x 2.000 mm.

Twin-shaft shredder, 380 volt power supply, ideal for plastic, wood, iron chips, paper. Loading mouth 620 x 570 mm, working area 350 x 300 mm, never used 0 hours Overall dimensions: 1500 x 1000 x 1500 mm Weight: 1000 kg Auction-ID: A7-44803-138

A counter-rotating side-feed twin-screw extruder Krauss Maffei used in the coextrusion process is available. Screw diameter: 40mm, material: rigid PVC, screw speed: 50rpm, throughput capacity: approx. 50-80kg/h, operating hours: approx. 42100h. Including roller guide with subframe. Documentation available. An on-site inspection is possible.

Twin-shaft shredder, 380 volt power supply, ideal for plastic, wood, iron chips, paper. Loading mouth 620 x 570 mm, working area 350 x 300 mm, never used 0 hours Overall dimensions: 1500 x 1000 x 1500 mm Weight: 1000 kg MACHINERY WITHOUT CE MARKING, NOT COMPLIANT WITH EU DIRECTIVES, INTENDED EXCLUSIVELY FOR NON-EU MARKETS Auction-ID: A7-44803-56

COMAC TWIN SCREW EXTRUDER EBC60, barrel with n. 2 x 60 mm. diam co-rotating screws, 42 L/D, spare : 2 screws and 1 barrel reconditioned to 100% performances, Mounted: screws + barrel in very good conditions, n.1 dosing unit with hopper, N.2 vacuum degassing points, d.c.132 kw Siemens main drive 400V 50 Hz, non-stop hydraulic screen-changer with 90 mm screens (available with fully automatic screenchanger, on separate request), hydraulic pack, fitted with strand die (available with water ring pelletizer on request) + stainless steel cooling bath with heat exchanging unit + air-blowing dryer, electric cabinet (for extruder, screen-changer, hydraulic pack), pelletizer for strands, TVV Cooling column for granule., constructed i n 2001, The line is offered totally or partially reconditioned (photos show the machine during reconditioning), installed power - used power in work: about 60-65% : 13 ...

For sale is a powerful Krone Swadro TC 760 medium rake in very neat condition. Technical data & equipment: • Working width: approx. 6.8 – 7.6 m • 2-rotor rakes for efficient merging of large quantities of forage • Hydraulically foldable for transport position • Robust design and high operational reliability • Tandem chassis for optimum ground tracking • Low-maintenance design • PTO drive • Lighting & warning signs for road transport available • Transport speed up to 40 km/h Condition: • Very good overall condition • Tines and rotors in neat condition • Ready for use – immediately available Special features: • High area performance due to large working width • Clean swath pattern – ideal for professional forage harvesting • Typically reliable Krone quality Auction-ID: 04F-QEP-1

BOLDT BFMA double-shaft paddle mixer – 220 L – stainless steel – year of manufacture 2007, Industrial double-shaft mixer with 2 rotation directions and front discharge, ---------------------------------------------------------------, Machine description, For sale is a BOLDT BFMA double-shaft paddle mixer from the year of construction 2007 in Stainless steel version., The machine is ideally suited for homogeneous mixing of:, - powder, - Granules, - spice blends, - Paste products, - Food and non-food products, The counter-rotating mixing shafts achieve a particularly even and gentle mixing., ---------------------------------------------------------------, ⚙️ Technical Data, - Manufacturer: BOLDT, - Type: BFMA, - Year of manufacture: 2007, - Gross content: 220 liters, - Net weight: 170 liters, - Material: completely stainless steel, - Discharge: 2 Frontentleerungsventile, - Mixin ...

Hot air fryer PHILIPS TWIN Turbo Star, used

Provided hand sanitizer station Auction-ID: A1-43573-257

Twin board final inspection station with motorised lift, weight scales and hydraulic lift tables. ANR 2253. Auction-ID: A1-45187-125

Twin board final inspection station with motorised lift, weight scales and hydraulic lift tables. ANR 2254. Auction-ID: A1-45187-126

In case you request pickup by courier additional cost will be added for packaging. please contact the seller for transport and packaging costs . All irregularities and signs of wear may not be clearly visible on the images. It is strongly recommended that you take advantage of the viewing day to personally inspect and assess the condition and appearance of the lot Brand EuroOven Type Twin 400 Power 6.45kW Electric connection 400V Total dimension L 900mm Total dimension W 550mm Total dimension H 560mm Auction-ID: A7-44605-32

Niemeyer twin rotor rake in good working order. Auction-ID: A3-43507-38030

CNC lathe for turning and machining metal parts. CNC control: Fanuc 16 T AA Max. turning diameter: 165 mm Turning length: 100 – 340 mm Diameter above bed: 220 mm Main spindle speed: 50 – 5,000 rpm Main spindle power: 5.5 / 7.5 kW Main spindle bar passing: 65 mm Sub-spindle speed: 50 – 5,000 rpm Sub-spindle power: 3.7 / 5.5 kW Sub-spindle bar passage: 42 mm C-axis: 0.001° Turrets: 2 Tool positions: 2 × 16 Motorized tools: 2 × 16 positions Strokes: X 175 mm / Z 240 – 680 mm Total power: 41 kVA Dimensions (mm): 3,500 × 2,800 × 2,000 Weight (kg): 5,500 Auction-ID: A1-44765-236

CNC lathe for turning and machining metal parts. CNC control: Fanuc 16 T AA Max. turning diameter: 165 mm Turning length: 100 – 340 mm Diameter above bed: 220 mm Main spindle speed: 50 – 5,000 rpm Main spindle power: 5.5 / 7.5 kW Main spindle bar passing: 65 mm Sub-spindle speed: 50 – 5,000 rpm Counter-spindle power: 3.7 / 5.5 kW Counter-spindle bar passage: 42 mm C-axis: 0.001° Turrets: 2 Tool positions: 2 × 16 Motorized tools: 2 × 16 positions Strokes: X 175 mm / Z 240 – 680 mm Total power: 41 kVA Dimensions (mm): 3,500 × 2,800 × 2,000 Weight (kg): 5,500 Serial No.: 1105-02957 Auction-ID: A1-44765-238

CNC lathe for turning and machining metal parts. CNC control: Fanuc 16 T AA Max. turning diameter: 165 mm Turning length: 100 – 340 mm Diameter above bed: 220 mm Main spindle speed: 50 – 5,000 rpm Main spindle power: 5.5 / 7.5 kW Main spindle bar passing: 65 mm Sub-spindle speed: 50 – 5,000 rpm Sub-spindle power: 3.7 / 5.5 kW Sub-spindle bar passage: 42 mm C-axis: 0.001° Turrets: 2 Tool positions: 2 × 16 Motorized tools: 2 × 16 positions Strokes: X 175 mm / Z 240 – 680 mm Total power: 41 kVA Dimensions (mm): 3,500 × 2,800 × 2,000 Weight (kg): 5,500 Auction-ID: A1-44765-237

A relatively new double-girder overhead crane Konecranes is available. Load capacity: 12t. Documentation available. An on-site inspection is possible.

CNC lathe for turning and machining metal parts. CNC control: Fanuc 16 T AA Max. turning diameter: 165 mm Turning length: 100 – 340 mm Diameter above bed: 220 mm Main spindle speed: 50 – 5,000 rpm Main spindle power: 5.5 / 7.5 kW Main spindle bar passing: 65 mm Sub-spindle speed: 50 – 5,000 rpm Counter-spindle power: 3.7 / 5.5 kW Counter-spindle bar passage: 42 mm C-axis: 0.001° Turrets: 2 Tool positions: 2 × 16 Motorized tools: 2 × 16 positions Strokes: X 175 mm / Z 240 – 680 mm Total power: 41 kVA Dimensions (mm): 3,500 × 2,800 × 2,000 Weight (kg): 5,500 Serial No.: 1105-02957

CNC lathe for turning and machining metal parts. CNC control: Fanuc 16 T AA Max. turning diameter: 165 mm Turning length: 100 – 340 mm Diameter above bed: 220 mm Main spindle speed: 50 – 5,000 rpm Main spindle power: 5.5 / 7.5 kW Main spindle bar passing: 65 mm Sub-spindle speed: 50 – 5,000 rpm Sub-spindle power: 3.7 / 5.5 kW Sub-spindle bar passage: 42 mm C-axis: 0.001° Turrets: 2 Tool positions: 2 × 16 Motorized tools: 2 × 16 positions Strokes: X 175 mm / Z 240 – 680 mm Total power: 41 kVA Dimensions (mm): 3,500 × 2,800 × 2,000 Weight (kg): 5,500

Formwork inclined columns newly hot-dip galvanized 2,10-3,50m a 40,90EUR/ pcs. New galvanized or painted construction supports 3.00m, 3.50m, 4.00m at great conditions directly from the factory. From 21,50€/ piece.+ VAT Construction support painted 1,60m - 2,90m = 21,50€/ piece reinforced version 2,00m - 3,50m = 23,50€/ piece reinforced version 2,30m – 4,00m = 26,50€/ piece reinforced version Construction support galvanized 1,60m - 2,90m = 25,90€/ piece reinforced version 2,00m - 3,50m = 26,90€/ piece reinforced version 2,10m – 4,00m = 29,90€/ piece reinforced version 1 frame for construction supports new, painted 70,00€ New inclined supports, painted 1,70m - 3,00m = 29,50€/ piece Inclined supports new, painted 2.10m - 3.50m. = 35,50€/ Piece Inclined supports new, painted 2,40m - 4,10m. = 38,50€/ Piece New inclined supports, ...

Column Drill ALZMETALL Type AB 4 SVMasch. No. 14805 Year of construction approx. 1980Drilling capacity 40 mmSpindle holder MK 4 - Short quillThroat projection 340 mmQuill stroke 180 mmTable size 710 x 560 mmColumn diameter 160 mmSpindle speed 30 - 765 rpm. infinitely variableMotor power 2.3 and 3.4 kW pole-switchableMains connection 380 volts, 50 Hz- Spindle speed over 2 motor speeds and infinitely variable gear- Gears with 2 gear stages for high torque at low speeds- Spindle on/off via

Column drilling machine GOTHABear power 30 mmSpindle holder MK 3 - long quill, throat depth 350 mmPine stroke 200 mmTable size 460 mmSpindle speed 160 - 750 rpm. 4 stepsFeed rate 0.1 - 0.2 - 0.3 mm/COLUMN diameter 160 mmMotor power 2.2 kWNerg connection 380 volts, 50 Hz- Spindle speed via 4 gear stages- Automatic feed- Rotatable drilling table with mechanical clamping- Table height adjustment via hand crank- Clamping surface at the machine foot 450 x 450 mmSpace required L x W x H 700