twin column used for sale

Single column - eccentric press KRUPP type PEKRD 125 hMasch. No. 2861 Year of construction 1977Compressive force 125 ton. Projection 400 mmTable size 950 x 750 mmPlunger area 800 x 540 mmTable opening 100 x 250 mmStroke adjustment 8 to 160 mmPlunger adjustment 100 mmInstallation height largest stroke at the top max. 550 mmStroke rate 60 strokes/min. Table height above floor 800 mmEngine power 10 kWNetz connection 380 Volt, 50 Hz- Hydraulic overload in the plunger- Compressed air clutch-brake combination ORTLINGHAUS-

Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15

Single column - eccentric press WEINGARTEN type ERV 40Masch. No. 537 / 65 Year of construction 1965Compressive force 40 ton. Projection 230 mmTable size 570 x 470 mmPlunger area 250 x 200 mmClamping pin hole 40 mmInstallation height max. approx. 520 mmStroke adjustment 8 - 88 mmPlunger adjustment range 63 mmStroke rate 70 strokes per minuteDrive power 3 kWNetz connection 380 volts, 50 Hz- Table height adjustment- Overload protection by crushing plate- Clutch-brake combination by WEINGARTEN friction threaded coupling-

Single column - eccentric press WEINGARTEN type ER 63Masch. No. 52A / 63 Year of construction 1963Pressure capacity 63 ton. Projection 280 mmTable surface 630 x 530 mmAdjustable plunger stroke 8-100 mmPlunger adjustment 63 mmStroke rate 65 strokes / min. Engine power 4 kWNetz connection 380 Volt, 50 Hz- Clutch-brake combination by WEINGARTEN friction threaded clutch- Electrical stroke release via foot switch- Wheel counters- Overload protection by crushing plate- Front crankshafts Support bearingSpace requirement L x W x H 1500

Single column - eccentric press PELS - RICHTER type PEKR 125Masch. No. 20684 Year of construction 1967Compressive force 125 ton. Projection 430 mmTable size 1100 x 750 mmPlunger area 890 x 650 mmTable opening 400 mmStroke adjustment 6 to 115 mmRam adjustment 100 mmInstallation height largest stroke top max. 450 mmClamping pin bore 50 mmStroke rate 60 strokes/min. Table height above floor 900 mmMotor power 7.5 kWNerg connection 380 volts, 50 Hz- overload protection by crushing plate in the plunger- compressed air

Single column hydraulic press SCHÖN type TES/CBbuilt in 1977Compressive force 63 ton. (160 bar)Projection 320 mmTable size 600 x 770 mmPlunger area 600 400 mmPlunger stroke 125 mmInstallation height max. 400 mm (with intermediate plate on the ram)Slide speed Rapid traverse downwards approx. 180 mm/sec. Ram speed work approx. 25 mm/sec. Pushrod speed upwards approx. 180 mm/sec. Table height above floor 870 mmDrive power 22 kWNet connection 380 volts, 50 HzTank capacity approx. 280 litres Hydraulic oil

Single column hydraulic press SCHULZ type SES 250Masch.Nr. 04.86.3511/3 Year of manufacture 1986Compressive force 25 ton. Retraction force 10 toProjection 360 mmTable surface 600 x 720 mmPlunger area 500 x 500 mmFailure opening in table 100 mmPin hole 40 mmPlunger stroke 400 mmInstallation height max. 600 mmTable height above floor 935 / 775 mmTank capacity hydraulics 380 litresDrive power 7.5 kWNet connection 380 volts, 50 Hz- Fixed stop adjustment in the press cylinder 180 mm- Light barrier

Radial drilling machine WEBO type R4bRFabr. No. 15 / E195 Year of construction approx. 1965Drilling capacity 40 mmThroat: approx. 1250 mmSpindle holder: MK 4Spindle speed: 30 - 1325 rpm. 9 stepsFeed from 0.12 - 2 mm/rev. 9 steps; used

Single-column eccentric press MÜLLER GEFREES type PDET 5 S/EKMasch. No. Year of manufacture 1988Compressive force 5 ton. Projection 125 mmColumn passage 170 mm Table surface 280 x 220 mmWaste height 90mmLifting area 160 x 100 mmLifting adjustment 4 to 40 mmRam adjustment 30 mmInstallation height largest stroke at the top max. 210 mmStroke rate 200 strokes/min. Clamping pin bore 25 mmTable height above floor 900 mmEngine power 0.55 kWNerg connection 380 volts, 50 Hz- pneumatic clutch-brake combination-

Column-mounted slewing crane DEMAG type KBK 100Year of construction approx. 2008Lifting capacity 80 kgSwivel range 270 Radius 2500 mmOverall height 1980 mmHeight to lower edge boom 1580 mm- Crane column KBK 100- Boom profile DEMAG C-profile cutter KBK 1- Base plate L x W x H = 260 x 260 x 25 mm (4 holes 18 mm)- painted yellow- Info about the short column, this slewing crane was mounted on a machine stand. The last picture shows a slewing crane mounted hangingdead weight approx. 100 kggood condition; used

Single-column eccentric press WEINGARTEN type E 40Masch. No. 643/62 Year of construction 1963Pressure capacity 40 ton. Projection 250 mmTable opening 150 x 80 and 200 mmTable area 560 x 460 mmPlunger area 250 x 200 mmPlunger stroke adjustable 8-88 mmPlunger adjustment 63 mmInstallation height 320 mmPin hole 40 mmStroke rate 100/130 strokes / min. Motor power 2.2 / 3 kWNetz connection 400 volts, 50 HzTable height above floor 840 mm- Clutch-brake combination by WEINGARTEN friction threaded coupling with TDC

Single-column eccentric press HELMERDING type TPEP 12 BMasch. No. 831-101 Comm. No. 76228 Year of construction 1976Compressive force 12 ton. Projection 155 mmTable surface 400 x 320 mmTable opening 125 mmPlunger area 125 x 100 mmLifting adjustment 6-60 mmRam adjustment range 40 mmClamping pin hole 25 mm with clamping pieceInstallation height max. 250 mmStroke rate 180 strokes/min. Drive power 1.1kW- Electric foot switch and 2-hand operation- Setup, single stroke 2-hand, single stroke foot and continuous running foot, automatic

2-column hydraulic press SELF-MADEBaucy approx. 1980Compressive force 6 ton. at 180 barCompressive force 5 ton. at 150 barCompressive force 4 ton. at 120 barCompressive force 3 ton. at 90 barTable top 400 x 340 x 30 mmPlunger plate 410 x 350 x 28.5 mmTable usable area between the guide columns 305 x 245 mmPlunger stroke 140 mmInstallation height max. 320 mmColumn diameter 35 mmTable height above floor 1050 mmHydraulic operating pressure max.180 barMotor power 4 kWNet connection 380 volts, 50 Hz- stepless

Bimak Mk3 Admission in drilling-spindle (morse): Mk3 Max drill capacity: 35 mm SPEEDS: 55 > 1000 rpm

Key data: 8000 mm, 1300 mm, 2200 mm

1 new CNC travelling column milling machine Make: Soraluce Model: FL 8000 Year of manufacture: 2014/15 Spindle hours: 3242 Hours: 4261 Control: Siemens 840 D Solution Line Technical data: Travel distances X-Y-Z: 8000 x 1300 x 1800 mm Travel C-axis: 360 degrees Plate clamping area: 6000 x 2000 mm Tool holder: SK 50 Capto C8 Speed range up to: 4000 rpm. Main drive: 43 kw. Rapid traverse: 35 m/min. CNC rotary table: 1600 mm 250 rpm Weight approx.; 40 to. Equipment / Accessories: Tool magazine: Controlled universal milling head Conveyor Full enclosure Complete cooling water system electronic handwheel IKZ. Fibro Reversible Clamp Fibr ...

Offer 25251 Specifications: - Drilling capacity in steel ST 60 45 mm - Drilling capacity in steel ST 60 55 mm - Drilling spindle holder MK 4 - Drilling spindle stroke 200 mm - Drilling spindle speeds infinitely adjustable 60 – 1600 rpm - Right - Counterclockwise rotation - 3 Feeds electr. Magnetic indentation 0.1; 0,16; 0.25 mm/rev - Projection 360 mm - Max distance drilling spindle – table / base plate 775 / 1255 mm - Table with 2 T-slots 630 x 540 mm - Height adjustable via rack with hand crank - Drive 400 V / 2.7 / 4.0 kW - Space requirement approx. W 800 x H 2100 x D 980 mm - Weight approx. 750 kg - with: - Machine vise - Keyless chuck 1 - 13 mm - Emergency stop button -Lighting

Tool holder: MK 2 Drilling capacity in steel: 18 mm Rotational speeds of the drilling spindle per minute: 220/ 290/ 440/ 720/ 950/ 1450/ Weight: approx. 300 kg

Offer 25248 Specifications: - Drilling capacity in steel ST 60 45 mm - Drilling capacity in steel ST 60 55 mm - Drilling spindle holder MK 4 - Drilling spindle stroke 200 mm - Drilling spindle speeds infinitely adjustable 60 – 1600 rpm - Right - Counterclockwise rotation - 3 Feeds electr. Magnetic indentation 0.1; 0,16; 0.25 mm/rev - Projection 360 mm - Max distance drilling spindle – table / base plate 775 / 1255 mm - Table with 2 T-slots 630 x 540 mm - Height adjustable via rack with hand crank - Drive 400 V / 2.7 / 4.0 kW - Space requirement approx. W 800 x H 2100 x D 980 mm - Weight approx. 750 kg - with: - Machine vise - Keyless chuck 1 - 13 mm - Emergency stop button -Lighting

Key data: 50 mm, 335 mm, 280 mm

Power: 7.8 kW Weight: 1,650 kg Table size: 630 x 500 Speed: 45 - 1,000 rpm Machine is ready for operation and can be dispensed immediately.

bore capacity in steel (diameter): 30.0 mm throat: 293 mm bore stroke: 140 mm morse taper: 3 MK table:: 515 x 360 mm turning speeds: 225 - 4300 U/min engine output: 1.0 / 1.6 kW column diameter: 115 mm distance spindle /table: 132 / 724 mm weight: 260 kg Machine height: 1790 mm Furnishing: - stepless speed adjustment - Reversing switch for R / L run - digital speed display - Connector and cable mounted - Spindle protection with electr. validation - 2 mtr. Connection cable with plug 16A The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 23.0 mm throat: 250 mm bore stroke: 100 mm morse taper: 2 MK table:: 370 x 300 mm turning speeds: 225 - 4300 U/min column diameter: 90.0 mm distance spindle /table: 140 / 670 mm engine output: 0.6 / 0.95 kW weight: 175 kg Machine height: 1770 mm Furnishing : - Mushroom pushbutton (latching) for EMERGENCY STOP - Reversing switch for clockwise and counterclockwise rotation - Motor protection switch - Infinitely variable speed adjustment - Digital speed display - Protection class IP 54 - Connection plug (fully assembled, cable length 2m) - Spindle protection with electrical fuse - Painting: DD textured paint, light gray RAL 7035, anthracite RAL 7016 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 40,0 mm throat: 320 mm bore stroke: 160 mm morse taper: 4 MK table:: 505 x 425 mm swivelling +/-: 50 Grad T-slots: 14,0 mm turning speeds: 90 - 1455 U/min quill feed: 0,1/0,2/0,3 mm/U column diameter: 120 mm total power requirement: 1,0 / 1,5 kW weight of the machine ca.: 380 kg. range L-W-H: 500 x 930 x 1870 mm characteristics - Vario drive for precise setting of the speed - Quill infeed either by hand or by mechanical feed - Easy tool change thanks to automatic tool ejector - Set speed can be read quickly and easily using the digital display - Solid, swiveling gray cast iron table with T-slots and coolant channel - The coolant system and lighting are included in the scope of delivery - Adjustable drilling depth stop, drilling depth can be read off using a scale - Right-left rotation device for thread cutting scope of delivery - Drill chuck arbor MK 4  ...

bore capacity in steel (diameter): 28,0 mm throat: 320 mm bore stroke: 150 mm morse taper: 3 MK table:: 500 x 350 mm turning speeds: 75 - 3010 U/min total power requirement: 1,35 / 1,7 kW weight: 290 kg range L-W-H: 600 x 700 x 1900 mm Description: - Standard with automatic quill feed (0.04 - 0.3 mm / rev) - Helical gear for optimal power transmission - High efficiency and smooth running thanks to helical gears - in combination steel against reinforced fiber material - Automatic quill feed - is deactivated when the set drilling depth is reached - Direction of rotation switch for clockwise and counterclockwise rotation for thread cutting - Stable and polished steel column, designed for heavy use - Quality ball bearings ensure high concentricity - 8 switchable speeds through powerful 2-stage drive motor - Adjustable drilling depth stop with mm scale Scope of delivery: - Keyless chuck 1 - 1 ...

pressure: 20 t throat: 200 mm stroke: 0 - 50 mm table:: 360 x 550 mm table:: 140 mm - Bohrung no. of strokes: 160 Hub/min bore: 35,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 240 mm total power requirement: 2,2 kW weight: 1.250 kg range L-W-H: 1310 x 1250 x 1860 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 30 t throat: 200 mm stroke: 0 - 60 mm table:: 400 x 600 mm table:: 150 mm - Bohrung no. of strokes: 140 Hub/min bore: 40,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 300 mm total power requirement: 3,0 kW weight: 1.670 kg range L-W-H: 1150 x 1350 x 2050 mm Furnishing: - Welded steel structure body frame - AISI 4140 (42CrMo4) alloy steel crankshaft - CNC ground for maximum precision SnBz-12 quality - Bronze bearings, ground for minimal surface resistance - 4 sides pneumatic clutch-brake combination - PLC control for safety (PILZ Germany) - Photo cell light barriers around the work table (PILZ Germany) - Two-hand and foot pedal control - Adjustable stroke - Central lubrication system - CE safety approval by TÜV - electrical equipment SIEMENS, SCHNEIDER, PHOENIX, OMRON The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 10 t throat: 160 mm stroke: 0 - 40 mm table:: 270 x 370 mm table:: 100 mm - Bohrung no. of strokes: 200 Hub/min bore: 25,0 mm - Werkzeug compressed air: max. 6,0 bar dayligth: 180 mm total power requirement: 0,75 kW weight: 590 kg range L-W-H: 1.168 x 1.010 x 1.670 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 50.0 mm throat: 370 mm bore stroke: 250 mm morse taper: 4 MK table:: 600 x 500 mm threading: M 42 Stahl turning speeds: 40 - 2100 U/min feed: 0.1 - 0.4 mm/U column diameter: 200 mm distance spindle /table: max. 600 mm distance spindle/base plate: max. 1190 mm total power requirement: 2.2 / 2.8 kW weight: 670 kg range L-W-H: 1020 x 750 x 2340 mm Scope of delivery - Keyed drill chuck 1 - 13 mm / B 16 - Drill chuck arbor MK 4 / B 16 - Reducing sleeve MK 4 / 3, MK 4 / 2 - Motorized table stroke - Coolant device - Electromagnetic spindle feed - Thread cutting device - Automatic tool ejector - LED machine light - Initial filling with Shell Tellus 46 - Digital speed display - Digital drilling depth display - Height-adjustable protective cover The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 50.0 mm throat: 360 mm bore stroke: 225 mm morse taper: 4 MK table:: 570 x 480 mm threading: M 42 Stahl turning speeds: 50-316 / 316-2200 U/min feed: 0.08 - 0.50 mm/U column diameter: 180 mm distance spindle /table: max. 580 mm distance spindle/base plate: max. 1185 mm total power requirement: 3.0 kW weight: 630 kg range L-W-H: 1020 x 750 x 2340 mm Scope of delivery - Keyed drill chuck 1 - 13 mm / B 16 - Drill chuck arbor MK 4 / B 16 - Reducing sleeve MK 4 / 3, MK 4 / 2, MK 3 / 1 - Motorized table stroke - Coolant device - Touchscreen - Automatic tool ejector - Electromagnetic spindle feed - Thread cutting device - Initial filling with Shell Tellus 46 - LED machine light - Digital speed display - Digital drilling depth display - Height-adjustable protective cover The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bore capacity in steel (diameter): 32,0 mm throat: 255 mm bore stroke: 120 mm morse taper: 4 MK table:: 385 x 335 mm turning speeds: 80 - 2130 U/min total power requirement: 1,1 / 2,2 kW weight: 125 kg range L-W-H: 460 x 900 x 1730 mm Furnishing: - Surface-machined work table - Height adjustable via rack and hand crank - Ground base plate with T-slots for clamping high workpieces - V-belt drive with balanced drive pulleys for smooth running - Adjustable drilling depth stop for precise infeed of the quill - Powerful 2-stage motor, speed range from 80 - 2130 rpm - Direction of rotation switch for clockwise and counterclockwise rotation included in the scope of delivery - Cross line laser device for comfortable work - Compact, stable cast iron construction in a modern design - Stable and polished steel column, designed for heavy use Scope of delivery: - Drill chuck arbor MK 4 / B 18 - Keyl ...

bore capacity in steel (diameter): 32,0 mm threading: 22 M bore stroke: 125 mm throat: 280 mm morse taper: 3 MK table:: 450 x 380 mm / 14er Nut turning speeds: 70 - 3.500 U/min feed: 0,1 / 0,2 / 0,3 mm/U column diameter: 110 mm weight: 320 kg range L-W-H: 500x800x2.100 mm total power requirement: 1,1 / 2,2 kW characteristics Infinitely variable speed, ideal for setting the desired one Cutting speed. Automatic tool ejector and Thread cutting device as standard. Electromechanical drilling feed, adjustable from 0.1 - 0.3 mm / rev Solid gray cast iron table with rotating and swiveling support surface T-slots in the machine base enable high workpieces to be clamped. Guaranteed concentricity = 0.02 mm, measured in the quill Hardened and ground gears ensure smooth running Adjustable drilling depth stop with an easily readable scale Scope of delivery: - Drill chuck arbor MK 3 / B 16 - Reducing s ...