twe dierdorf gmbh used for sale

X-travel: 600mm, y-travel: 600mm, z-travel: 500mm, max. rotational speed: 1-17,500/min, max. load: 600kg, number of tool slots: 2x 42, max. tool weight: 350kg, controls: Siemens 840D SL, connected load: 133kVA, length: 4800mm, width: 3370mm, height: 7500mm, weight: 20t with 3D probe and documentation, without operational hours counter, was maintained regularly, an inspection is possible.

X-travel: 650mm, y-travel: 650mm, z-travel: 650mm, clamping surface: 400x400mm, max. load: 400kg, length: 4600mm, width: 3920mm, height: 2900mm, weight: 12.8t, operational hours counter: ca. 60,000h, with documentation, was maintained regularly.

2 centrifugal pumps / self-priming Type: KSP 50 /150-2.3 Manufacturer: KPA Artern, Germany Capacity: 10,000 l/h Speed 1,420 rpm. Connections: Inlet NW 50 / Drain NW 50 Material: Stainless steel Medium: beer, wine, milk, etc. Connection: 380 V, 2.2 KW Weight: approx. 43 kg Dimensions: 50 x 30 x 35 cm Technical condition: refurbished

For sale a CNG natural gas traportable bundle Wystrach 600 litre 200 bar. Operating pressure: 200 bar Built: 2005 steel-built Dimensions: 120 x 80 x 180 cm Weight: 1000 kg

The IRS 120 Easy is the perfect entry point into cable recycling. The special combination of large flywheels and multi-part segment cutting knives makes it possible to efficiently recycle old cables made of copper or aluminium even without high power consumption and without shredding. The machine impresses with its small footprint, is easy to maintain and easy to use. Compared to most of the competition's systems, the machine has two separate fans for separator air and dust removal. This eliminates the usual interactions between more or less clogged filters and the purity of the copper granules. In addition, the separator air is not roughly adjusted via throttle valves, but by sensitive adjustment of the fan speed. This gives you the best qualities in finished copper. This machine is an immediately available storage machine and has 4 screen inserts, electronic pre-equipment for ...

This is a special machine for the machining of ball bearing slewing ring supports, controls: Siemens SINUMERIK 810M, with documentation, one circuit board is defective.

1 Qty. 1 Second-hand 3 roll bending machine Mfc.: SW GmbH Type: SRMV G Built: 1989 Strip width max.: 2000 mm Wall thickness: max. 25 mm / Ø 530 mm 2 Qty. 1 Second-hand 3 roll bending machine Mfc.: SW GmbH Type: SRMV Hy Built: 1981 Strip width: max. 3500 mm Wall thickness: max. 12 mm 3 Qty. Second-hand 3 roll bending machine Mfc.: SW GmbH Type: SRMV Hy Built: 1983 Strip width: max. 3500 mm Wall thickness: max. 19 mm 4 Qty. 1 Second-hand 4 roll bending machine Mfc.: SW GmbH Type: SVRM Built: 1981 Strip width: max. 2000 mm Wall thickness: max. 16 mm

X-travel: 600mm, y-travel: 600mm, z-travel: 500mm, max. rotational speed: 1-17,500/min, max. load: 600kg, number of tool slots: 2x 42, max. tool weight: 350kg, controls: Siemens 840D SL, connected load: 133kVA, length: 4800mm, width: 3370mm, height: 7500mm, weight: 20t with 3D probe and documentation, without operational hours counter, was maintained regularly, an inspection is possible.

Haake water bath F3 thermostat thermal bath water bath temperature 20°-270°C Manufacturer: Haake GmbH Type: 001-4202

Manufacturer: EM HART Teknologies (Tucker GmbH) Type: ERF230000/3 3x5

1 cool- and heatable, sterilizable, vacuum-resistant stainless steel process tank for the production of dairy, delicatessen, pharmaceutical and cosmetic products Manufacturer: Seitz-Werke, GmbH Type: DB 170. FW Machine. No.: 2226 Content: 187 litres Material: stainless steel V4A / 1.4571 Product-contacted parts polished Product room: pressure-resistant to 3 bar Double jacket for heating and cooling Double jacket: 35.5 litres, pressure-resistant to 2 bar Operating temperature: up to 133 C Ventilation and vent valve Rise tube Pointer thermometer from 0 - 160 C Pressure gauge Safety valve Filling opening NW 60 Bottom seat valve NW 20 Agitator flange available Operating instructions + list of spare parts, etc. Dimensions: approx. 0.8 x 1.4 m Weight: approx. 200 kg Technical condition: used, excellent as good as new operating condition

X-travel: 600mm, y-travel: 600mm, z-travel: 500mm, max. rotational speed: 1-17,500/min, max. load: 600kg, number of tool slots: 2x 42, max. tool weight: 350kg, controls: Siemens 840D SL, connected load: 133kVA, length: 4800mm, width: 3370mm, height: 7500mm, weight: 20t with 3D probe and documentation, without operational hours counter, was maintained regularly, an inspection is possible.

2 centrifugal pumps / centrifugal pumps, self-priming Type: KSP 50 /150-2.3 Manufacturer: Kyhäuserhütte Artern, Germany Power: 10,000 l/h Speed: 1,420 rpm. Head: 14 m Connections: Inlet NW 50 / Drain NW 50 Design: Stainless steel Media: beer, AfG, milk, lye, etc. Connection values: 380 V, 50 Hz; 2.2 KW Weight: approx. 43 kg Dimensions: 50 x 30 x 35 cm Technical condition: refurbished

Weight: 1.05t, with documentation, an inspection is possible.

Was used to rework profile rollers for a hot rolling mill, was regularly serviced, with accessories, without spare parts, on-site inspection is possible, no videos available.

Working length: 3050mm, pressing force: 2500kN, number of operational hours unknown, including set of tools and documentation, on-site inspection is possible.

Hydraulic pressure: 200 bar, with documentation and length stop, on-site inspection is possible, was used for cutting steel reinforcement pipes for plastic profiles to length, the machine has currently been standing under cover in an outdoor storage facility for two years, the linear guides are affected by rust film, a function test cannot currently be carried out.

1 banding machine with shrink tunnel Manufacturer: Urban Maschinenbau GmbH, Germany Type: SB 500 Fully automatic linear banding system to different types of products in groups and stacked high with shrink wrap to package. The banding system works with two film roles, cross sealed. Product feed with motorized infeed conveyor, linear Motorized film reel (top and bottom) Sealing and cutting through hot clamping with electronic temperature control Control Panel for easy control of all machine functions Direction of rotation of the machine: from left to right Ventilated electric cabinet Formats / products: Length: 200 mm Width: 180 mm Height: 210 mm Capacity: up to 2,400 products / h, depending on the product integrated heat shrink tunnel Tunnel width: 500 mm / tunnel height: 220 mm Electr. Supply: 380 V, 50 Hz Dimensions: approx. 2.5 x 2.0 x 1.8 m Weig ...

We offer for fast CHP Scania DC12-16 motors/hull motors in exchange. MIW Motoren-Instandetzunsg-Werk GmbH North-West Ring 8 D-27404 Zeven/Germany E-mail= info at miw-zeven

We are stocked for CHP Fast with Scania Motor DC12/16 fuselage motors. MIW Engine Repair Plant GmbH North-West Ring 8 D-27404 Zeven/Germany e-mail: info at miw-zeven

Max. operating temperature: 200°C, usable space: 4.42m³, steam room volume: 5.6m³, volume flow: 9.87m³/min, heating output: 30kW, nominal output: 32.2kW.

Max. bending diameter: 30mm, an inspection is possible.

Special design, cutting length: 6300mm, max. passage height: 2200mm, max. trimming height: 2100mm, cutting depth: 80mm, power: 5.5 kw, saw blade diameter: 303mm, dimension display: digital, with continuous small parts support, tilt: pneumatic, extraction: 1,200 m³/h, 2 x 100mm, installation dimensions: 7620 x 1500mm, room height: 2990mm.

Closing force: 550kN, opening stroke: 400mm, mould height: 250-650mm, column distance: 360x335mm, max. ejector stroke: 80mm, table dimensions: 565x540mm, max. tool weight: 600kg, screw diameter: 38mm, controls: Procan MD, length: 3250mm, width: 1140mm, height: 2040mm, weight: 2.25t, operational hours counter: 29,664h, with robot interface.

Kneading machine Kemper SPL 75 - 100 litres Masch. No. 672500 Strong and robust kneading machine in very good and well-maintained condition. Kneading machine from bakery.- 2 speeds- front and return pulse function timer no longer runs out- Operating hours: see photosPallet size, weight approx. 500kg (note when picking up) The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

P181 - used approx. 40 m³ / 40,000 litres PE-HD-tank, plastic tank, flat bottom tank, double-walled with an outer hull. specifications: capacity: approx. 40 m³ / 40,000 litres material: PE-HD tank, plastic tank manufacturer: Formoplast Kunststofftechnik GmbH measurements: Ø approx. 3,49 m outside / Ø approx. 3,00 inside x height tank approx. 5,70 m / total height approx. 6,50 m mark of conformity: PA-VI 321.103 specific weight: 1,13 kg/L media: former chemical tank for formalin DIBT and media list available, suitable for AHL and ASL PE-HD tank, professionally cleaned and in good condition. Double-walled, i.e. with an outer hull, non-translucid, various connections such as ventilation, inlet, suction pipe, etc., lid on top of the roof. According to the media list suitable for many different chemicals e.g. iron chloride, hydrochloric acid, acetic acid, caustic soda, sul ...

Suitable for rigid foam, sawing width: 1250mm, max. sawing height: 200mm, max. speed: 12m/min, with controls cabinet or saw blade.

Painting drying plant Giardina Forno Statico MOS 3D Masch. No. 050354 Built in 2006 User manual available This plant is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

System includes (1) Servo-Controlled Filling Machine Rationator Robomat L1M, number of filling stations: 8, controls: RATRONIC-CONTROL, weight: 1.1t, year of construction: 1999 (2) Capper Rationator Robocap 1/4, weight: 1.35, year of construction: 1997 (3) Labelling Machine Breitner TPE 6033, year of construction: 2004, has been regularly serviced, on-site inspection is possible.

Format: 50-1040mm, an inspection is possible.

Connected load: 2.95kW, without documentation, an inspection is possible, was in use until 2014.

Trolley dimensions: 920x910x1950mm, connected load: 24kW, length: 1560mm, height: 2560mm, with documentation, a few years ago the electrics were completely overhauled.

P213 - used approx. 30 m3 / 30,000 L polyester tank, GRP tank, Speidel tank, standing, flat bottom. Technical details: Content: approx. 30 m3 / 30,000 litres Material: Polyester tank / GRP tank Manufacturer: Speidel Tank- und Behälterbau GmbH Dimensions: approx. 3.00 m x approx. 4.60 m high Other: Used polyester tank in very good condition, manufacturer Speidel. Vertical flat bottom tank, dome at the top of the roof, several connections, incl. filling line. The container can be used as a storage tank for many different media such as water, liquid food, whey, potato vapour bowls, molasses, manure, seepage juice, rapeseed oil or as a rain collection tank, etc. Price on request. Transportation can be arranged cheaply. We can also rework the tank as desired, please ask us. It is not possible to update all our listings daily. As our stock is constantly changin ...

Machine type TIG inverter welding system gas-cooled DC system Make Merkle Type MobiTIG 190 DC Connection voltage 1 x 230 volts Adjustment range 5 - 190 ampere Switch-on time 20% ED at 180 amperes 100% ED at 90 amperes Current adjustment infinitely variable max. weldable material thickness 5 mm Cooling inverter by built-in fan Cooling burner gas-cooled Version of portable assembly line Fuse 16 Ampere Dimensions L x W x H 355 x 160 x 275 mm Weight 9 kg Age 6 months Condition workshop-tested, very good, incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece TIG burner 4 mtr. Long 1 piece ground cable 1 piece pressure reducer with 2 pressure gauges 1 pair of TIG gloves 1 piece spare part box kpl. Equipped 18 month warranty 1 piece user manual New price €1,590.00 + VAT Price kpl. wi ...

There are twelve roasted coffee silo cells available, capacity: 16x 11t, with documentation, aspiration and bucket elevator.

Suction fan Pipe of 300 mm Engine 4 kW The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/Ersatzteile durch MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system+technik GmbH Maschinenbau Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

STANZNIETZUFÜHRER Manufacturer: EM HART Teknologies (Tucker GmbH) Type: ERF230000/3 3x5

Max. usable area: 1600x2450mm, clearance: 35mm, table dimensions: 1800x2990mm, length: 3000mm, width: 2250mm, height: 1300mm, weight: 565kg, with head 7283, head 4002, milling device Aristomat SL 1625, 2x scoring attachment, 4x creasing attachment, 2x cutting attachment, 4x tweezers, 12x Allen keys, software: SIGN software FlexiLetter (dongle) and various small parts, on-site inspection is possible.

Connected load: 55kW, weight: 6.8t.

+ ATTENTION - PRICE DROP! + Prices are rising, ours are falling! + Our prices are reduced by 50% now, + due to warehouse restructuring! + Also, consider taking a look at our other offers in stock. Industrial extraction system NESTRO NE160 manufacturer: NESTRO Lufttechnik GmbH type: NE 160 mach.-Nr.: 1041 year of construction: 1994 comm.-Nr.: 0549/210/100/0859 stock-Nr.: 1803 + Regular Price: 2.180,- € > Reduced Price: 1.090,- € BN + All prices are shown without taxes (net price) Technical Data (According to manufacturer) intake manifold Ø: 160 mm filter area: 11,5 m² volume flow: 1.780 m³/h (after cleaning) Negative pressure in front of ventilator: 3.000 Pa Minimal volume: 1.447 m³/h Negative pressure in front of ventilator: 3.550 Pa Negative pressure at connection: 3.100 Pa – (4,0 m hose length mit Ø 160) working temperature: 5° to 4 ...

Absorption Refrigerator System with cooling tower Karlsruhe KRD 1/12-28-3. Cooling output: 214kW, permissible temperature: 10-60°C, max. overpressure: 1bar, nominal volume flow: 87.1m³/h, with Radial Fan Wolter GmbH TRZ 900/80 KTK and Absorption Chiller Carrier SCS 16LJ-03E-LC.

Table crosscut saw Irion UKS 800 DS Masch. No. 1360 Stop left 7 m Stop right 3.5 m Feeder Roller conveyor 400 mm wide Roll 300 mm long with programming control with documentation with data storage L x W x H Machine: 1650 x 1650 x 1750 mm Built in 1994 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4952 Eriswil/EN-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Mill mat 4 CH-4952 Eriswil/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Hydraulic pressure: 150bar, connected load: 32kW, including two containers.

Swash-up machine: 2-deck machine: 3.6 m2 / deck product-contacted parts in stainless steel 1.4301 ( AISI ) 2 x Ball knock cleaning Safety clamping screws Lifting device incl. 2 x sied, mesh size as desired: from 0.1 - 5 mm Height of the machine without frame: 1620 kg Weight: 1820 kg. --> Machine completely grounded.

Machine type Electrode inverter welding rectiveror Make Merkle Type LiteARC 180 Connection voltage 1 x 230 volts Adjustment range 20 - 170 amperes Switch-on time 25% ED at 170 amperes 60% ED at 130 amperes 100% ED at 115 amperes Current adjustment infinitely variable max. weldable material thickness 4 mm Cooling inverter by built-in fan Version of portable assembly line Fuse 16 Ampere Dimensions L x W x H 360 x 140 x 230 mm Weight 5 kg Age 12 months Condition workshop-tested, very good, as new incl. UVV test protocol Scope of delivery Welding system with the following accessories: 1 piece ground cable 1 piece electrode cable 1 piece hand shield 1 piece of lens 90 x 110 mm, white 1 piece protective glass 90 x 110 mm, 10 DIN 1 piece slag hammer, heavy version 1 piece steel wire brush, 2-row 1 piece mains plug 230 ...

There are twenty identical BIOTEST RCS High Flow HYCON available.

Pendulum circular saw Irion Cutting width 350 mm Roller table 3000 mm L x W x H: 600 x 500 x 1800 mm Weight approx. 250 kg Built in 1978 The machine is in good condition, ready for operation. Changes, mistakes, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Shielding box for electromagnetic compatibility, length: 728mm, width: 520mm, height: 520mm, with full absorber lining (ferrite absorber), 10x feed-through filters (banana sockets), BNC feed-through, cold device feed-through (filtered), Sub-D feed-through (filtered), waveguide feed-through for optical cables, double EMC seal, antenna feed-through (conduit feed-through), shielding attenuation and two gas pressure springs.

With accessories, an inspection is possible.

Max. circuit board dimensions: 330x420-400x495mm, conveyor speed: 0-2.5m/min, an on-site inspection is possible.