141,810 used machines on RESALE, but how to find them? Machine Search
Thread cutting gear Pick-up device partially revised
Schuette multi-spindle rotary machine SF 26-6 1984 built - mechanical gearbox - independent feed from the Laengsschlitten Position 4 - Thread cutting gear with thread cutting spindle
Inv. Num. : 9002 Type: LB3000EXII MYW800 Producer: OKUMA Created: 2014 Parameters: Control system: OKUMA OSP-P300L CNC Switch-on hours: 65458 h Hours: 36054 h Maximum turning length: 785 mm Max. turning diameter: 480 mm Max. turning diameter: 340 mm Spindle diameter: 80 mm Motor power: 22 kW Minimum spindle speed: 45 1/min Maximum spindle speed: 5000 1/min Travel X: 260 mm Travel Y: 115 mm Travel Z: 510 mm Tool magazine: 12 pieces Length: 3330 mm Width: 1800 mm Height: 2250 mm Weight: 5250 kg Equipment: Baking Collets Axis C Sub-spindle Powered tools OSP-P300L Advanced One Touch CF-M-E FILTERMIST FX4002 Suction High-pressure cooling Grips Tool Holder Reducer insert tube In June 2019, the spindle was repaired due to defective bearings. In June 2025, the U4 control unit was replaced. In October 2025, the M control unit w ...
Rotary table E20 Table working surface 2000x2000mm Table height 910 mm The biggest load of the workpiece table 200000N Movement for sleigh bed 1200 mm Longitudinal feed 2,8-8-22.4 mm min-1 Circular shift on average of 2000 mm 5.8-16.4-48.1 mm min-1 Rapid longitudinal 1245 mm min-1 Rapid circular diameter of 2000 mm to 2600 mm min-1 4kW electric engine for the displacements Floor surface 3000x2765mm Table weight 9350 kg
Key data: 1600 mm, 3500 mm, 800 mm
For sale is: 1 Piece Used Face and Lace Lathe Manufacturer: Werkzeugmaschinenfabrik Zerbst GmbH Type: DP1 / S3 x 3500 Year of manufacture: 1994 Technical data: Largest turning diameter over bed: 1,600mm Center width: 3,500mm Spindle bore: 100mm Face plate diameter: 1,250mm Total mass of the machine: approx. 24.8t incl. documentation Further pictures and videos can be sent on request. The following things have been renewed/repaired on the machine in the last four years: At the end of 2022, the tailstock was completely overhauled. New bearing and new tip and lubrication. 2024 Cross Support regenerated. Refurbishment of the wedge strips with new sliding coating, snatchers on the guideways smoothed by scraping, Bearing seats of the spindles made smooth, wedge strips in the contact surface and covering surface scraped. Lubrication pump cle ...
CNC controller: Fanuc 18i-TB Capacity X-axis travel mm: 157,5 Y-axis travel mm: 35 Z-axis travel mm: 464.8 B-axis travel mm: 600 C-axis: 360º (0,001º) Turning length mm: 399 Max. turning diameter mm: ø: 190 Distance between spindle centers mm: 750 Bar work capacity mm: 52 Upper turret Number of tool slots St .: 12 Speed driven tools RPM: 6.000 Drive power driven tools kW: 5.5 / 3.7 Number of upper turrets: 1 Lower turret Number of tool slots St .: 12 Speed driven tools RPM: 6.000 Drive power driven tools kW: 5.5 / 3.7 Milling function: Both Turrets Main spindle Speed spindle rpm: 5.000 Counter spindle Speed spindle rpm: 4.500 Drive power spindle kW: 11 / 7.5 Equipment Chip conveyor Part catcher Workarea light Bar Loader RBK 10016 Working time hours Potencial nominal kVA: 67,2 Basic machine dimensions / weight Length mm: 3.675 Width mm: 2.258 Height ...
Schuette multi-spindle rotary machine SF 26-6 1980 built -with thread cutting device - prepared for centrage suction system - standard Schuetz control D8gdo29 - mechanical gearbox - Balluff cam switch - standard rod guide
Schuette Multi-spindle rotary machine Name: Schuette SF 20-6 Curve controlled Number of spindles: 6 Built: 1984 max. rod diameter: around 20 mm SW 17 mm AK 18 mm VK 14 mm max. rod feed: 80 /(160) mm Number of independent Laengsschlitten: 6 Total / working distances (stand): 63/40 mm " " (special) up to: 100/63mm Number of independent cross slides: 6 Total/ work routes Medium and top slide up to: 32/20 mm Slide up to: 40/25 mm Spindle circle diameter: 224 mm Main times min/max.: 0.36/150 sec. Off times min./max.: 0.45/0.80 sec. Spindle speed from / to: 900-5000 rpm in the 2nd area: 355-2000 rpm Rated power of the drive motor: 15 KW Connected power: 50 kVA Drive engine speed: 1500 rpm Length Width (in standard performance) 3705 1320 mm incl. rod guide (in standard output) 6335 mm Weight without rod guide a ...
Gildemeister 6-spindle rotary machine, curve controlled max. rod passage: 32.0 mm for rods up to 3.30 m - incl. rod guide, - Steel processing, run with cutting oel - easily equipped with tools Cmvlgfoyc - 1 set of clamping and feed pliers - Alternating wheels (on machine) - 1 set of curves for cross slides - 1 set of curves for main slide
Key data: 130 mm, 160 mm, 6000 1/min
CNC lathe ARIX / HUMMER T-42CL + bar loading magazine Robust Nitro + chip conveyor – year of construction 2025 For sale is a modern CNC lathe of the type HUMMER T-42CL (ARIX CNC Machines) including bar loading magazine Robust Nitro. The machine was built in 2025, is in very good condition and is ideal for cost-effective series production. Technical data: Model No.: T-42CL Manufacturer: ARIX CNC Machines (Taiwan) Year of Make: 2025 Spindle speed: up to 6,000 rpm Bar Passage: 42 mm Max. turning diameter: approx. 130 mm Max. turning length: approx. 160 mm Axles: X: 225 mm Z: 235 mm Y: 385 mm Main spindle: Power: 7.5 kW Collet holder: A2-5 Tool Stations: 5 lathe tools + 4 driven tools Total: 8 Lots Machine weight: approx. 3,300 – 3,500 kg Equipment: Bar loading magazine Robust Nitro (automatic material feeding) Live Tooling Suitable for series production ...
Schuette multi-spindle rotary machine SF 50/51-6 Rod turning machine run on schneidoel standart Schuetz control mechanical gearbox Hydraulics integrated into the machine with snail-spaenefoerer
used
AUTOMATIC SPINNING LATHE DENN RPE-290 Denn Mod.RPE-290 Automatic Spinning Lathe- Spindle Speeds 615/1060/1825 RPM. More information on request.
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 250 mm -Passage: Ø 76 mm -Hole circle: Ø 230 mm -Weight: 23 kg
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 250 mm -Passage: Ø 91 mm -Hole circle: Ø 170 mm -Shot: short taper 8 -Weight: 47 kg
Gildemeister 6 Spindle Lathe AS 32-6 - Spindle stop set-up - Pneum pick-up device. - Zubehoer at an extra cost - Cross hole drilling - Thread cutting gears - Thread cutting device - wahlw. Fraeseinrichtung Querschl. - Spaenefoerderer
CNC slot machine Gildemeister GLD 25 with counter spindle Technical data: Manufacturer: Gildemeister Type: GLD 25 Built: 1999 Control: FANUC Series O-T Main spindle: - max. turning diameter: 25 mm - max. speed: 8,000 rpm - maximum stroke (Z-axis): 160 mm Counter spindle: - max. turning diameter: 25 mm - max. speed: 8,000 rpm - maximum stroke (C-axis): 265 mm - Rapid speed C-axis 15 m/min Sled: - Slide: X= 30 mm, Y= 220 mm - Rapid x-axis 10 m/min - Rapid y-axis 15 m/min - Number of WZ on the sled: 5 + 3 (driven) - Speed WZ (driven) : 6,000 rpm Accessories: - Chip conveyor -Bar loader: IEMCA MINI BOSS 325/32 Dimensions LxWxH: - Machine with chip conveyor 3150 x 1100 x 1700 mm - Bar loader 3900 x 800 x 1400 mm Weight: - Machine: approx.2000 Kg - Bar loader: approx. 1000 kg. - Total weight: approx. 3,000 kg
Gildemeister 6-spindle rotary machine, curve controlled max. rod passage: 32.0 mm for rods up to 3.30 m - incl. rod guide, - Steel processing, run with cutting oel - easily equipped with tools Sowiabeb - 1 set of clamping and feed pliers - Alternating wheels (on machine) - 1 set of curves for cross slides - 1 set of curves for main slide
Turning tool holder, tool holder, turning tool, turning tool holder, tool holder, axial tool holder -Tool holder: 27 mm -Number: 9 recordings -Price: per piece -Dimensions: 73/67/H197 mm -Weight: 4.7 kg
Machine vise base plate, clamping plate, vice plate, turntable -with: T- round groove -Grad display -Dimensions: 265/185/H50 mm -Weight: 4.4 kg
Schuette multi-spindle rotary machine SF 26-6 1987 built 6-spindle rod turning machine with hydraulic catch slide prepared for Co2 Loesch plant run with cutting oel Schuetz control mechanical gearbox separate hydraulic unit -- Pick-up device with hydraulic voltage and back-weighing machining without Spaenefoerderer standard pole guide unabhaenger Laengsschlitten feed to position 1,2,4,5 ...
Boring head, spindle head, drilling head, grooving drill head, grooving head, spindle drilling head, boring head, spindle tool -Tool holder: adjustable -Recording: MK6 -Measures: see pictures -Dimensions: 420/140/163 mm -Weight: 11.2 kg
Gildemeister Multispindle Slot machine 6- Spindler Type: AS 25-6 Pick-up device back-valued processing pneumatic stop Balluff cam switch IEMCA PRA Bar loader Oil mist separator (electrostat.) Conveyor Machine has been retrofitted in the past
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 190 mm -Passage: Ø 57 mm -Weight: 10 kg
Machine vise base plate, clamping plate, vice plate, turntable -with: T- round groove -Grad display -Dimensions: 235/175/H50 mm -Weight: 6 kg
Parallel lathe Geminis GE650S to be rebuilt. Distance between points: 1000mm. Flip on bench: 680mm. Flip on cart: 410mm. Flip over neckline: 850mm. Main hole: 84mm. Motorized trolley and charriot. Speeds: 18 (13-1000rpm). Main engine: 15hp. Plate and trolley protections and CE RD1215/97 certificate. Quick-change plate and turret.
various accessories / spare parts for Tornos AS 14
Turning tool holder, tool holder, turning tool, turning tool holder, tool holder, axial tool holder -different recordings: 10 -from: WNT-Mastertool -Sale: only complete -Price: complete -Weight: 36 kg
Table diameter 1450mm Max working diameter 1600mm Max height under crosstravel 1000mm Nr. 02 RAM Visualization by DRO 4 axes Good working conditions Machine weight18 ton
CNC CONTROL: MSD 501 II, FANUC FEATURES: DIAMETER ADMITTED ON THE BED, MM 680 MAXIMUM TURNING DIAMETER 440 MM N1 MAXIMUM TREATMENT DIAMETER N2 322 MM MAXIMUM TURNING LENGTH, MM 471 THE STANDARD MACHINING DIAMETER MM170 MAIN SPINDLE: STEP PANEL 45 MM COUNTER SPINDLE: HOLE PITCH LINE 43 MM TURRET 1: POSITION N12 ALL MOTORIZED TOWER 2: POSITION N12 ALL MOTORIZED
Three-jaw chuck, three-jaw lathe chuck -Chuck size: 240 mm -Mounting flange: M80 x 6 mm -without: interchangeable jaws -Weight: 26 kg
Three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Chuck size: Ø 190 mm -Through hole: Ø 57 mm -Weight: 19 kg
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 200 mm -Weight: 18 kg
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 190 mm -Rezess: Ø 155 mm -Hole circle: Ø 174 mm -Passage: Ø 54 mm -Weight: 11 kg
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 250 mm -Short taper mount: Ø 140 mm -Passage: Ø 76 mm -Weight: 30 kg
Machine weight: 39,000 kg Faceplate diameter 2000 mm number of supports: 2 pcs. Dimensions : Height 6280 mm width 6600 mm length 4800 mm Extras: Right support with turret head, left and side - sliders. Digital indication of NS 114. Technical condition at the time of sale: Defective rotary amplifier main drive-replacement is required. Require replacement of cables and wires external piping:-machine control cabinets. Repair and adjustment of electrical parts. Not operated since 1994 The maximum dimensions of a workpiece Height 1300 mm Diameter of 2000 mm Weight 15 000 kg
MAX DIAMETER OF ROD: 100 MM MAX CUTTING DIAMETER: 552 MM MAX TURNING LENGTH: 1.195 MM TURRET: 16 ROTATION SPEED: 2800 RPM CONTROL: FANUC 32 B INCLUDES: AUTOBLOK STEADY SLU-3.1 – ZS CAPACITY: 20-165 MM AUTOMATIC FEEDER FOR BARS BREUNING – MOD. MUK 10016-II
Table diameter 2.000 mm Working diameter 2.000 mm Machine under retrofit/rebuilding to install CNC Mechanical ready, totally rebuilt.
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 250 mm -Throughout: Ø 80 mm -Short taper: 6 -Weight: 28 kg
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 250 mm -Throughout: Ø 70 mm -recess recess: Ø 194 mm -Weight: 20 kg
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 225 mm -Throughout: Ø 70 mm -Weight: 25 kg
Vertical lathe KOLOMNA 1540 T CONVENTIONAL MACHINE READY TO INSTALL Spindle diameter 4.000 mm Working diameter 4.140 mm Max working height 2.060 mm Ram travel 1.250 mm Weight over spindle 100 ton Motor power spindle 100 kW Boring/milling unit included Nr.02 RAM with visualization by DRO Excellent conditions, mechanical really like a new.
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 250 mm -Throughout: Ø 70 mm -Weight: 27.5 kg
Three-jaw chuck, three-jaw lathe chuck -Chuck size: Ø 250 mm -Throughout: Ø 80 mm -Weight: 18.5 kg
Three-jaw chuck, 3-jaw chuck -Chuck size: Ø 200 mm -Passage: Ø 55 mm -Weight: 12.5 kg
Three-jaw chuck, 3-jaw chuck -Chuck size: Ø 200 mm -Passage: Ø 55 mm -Weight: 14 kg
MACHINE IS IN GOOD WORKING CONDITION Machine need center horse and support for the clamp cutting tools. Bj0ie7dcoa Machine Has ben used in Switzerland, after thay realize they need that both suports, they took it off and use on other lathe.
Three-jaw chuck, three-jaw lathe chuck, 3-jaw chuck -Chuck size: Ø 250 mm -Throughout: Ø 80 mm -Weight: 24.5 kg
Three-jaw chuck, three-jaw lathe chuck -lining size: Ø 190 mm -Rezess: Ø 155 mm -Passage: Ø 54 mm -Weight: 11 kg
maximum number of results exceeded
please refine your search
