turbine generator used for sale

Key data: 3 KW, 3 kVA, 11000 V

2016 Jenbacher 616 Containerised CHP Unit – Natural Gas Generating Set 2.7 MW at 11kV UK Power Generators Ltd is offering is offering a Jenbacher 616 (J616) containerised Combined Heat and Power (CHP) generating set, manufactured in 2016, configured for natural gas operation and built to ISO 8528 standards. This is a complete containerised power and heat generation solution, ideal for industrial facilities, district heating, greenhouses, utilities, and energy centres seeking high-efficiency CHP performance. Technical Specifications of the available unit: Manufacturer: GE Jenbacher GmbH & Co. OG (Austria) Model: Jenbacher 616 Year of Manufacture: 2016 Fuel Type: Natural Gas Rated Electrical Output: 2.7 MW Rated Voltage: 11,000 V Frequency: 50 Hz Rated Power Factor: 1.0 Rated Current: 141 A Performance Class: G2 Max Ambient Temperature (Intake Air): 30°C  ...

Speed 1500 1/min, output 380-415 V (3-phase) 50 Hz Auction-ID: A1-46045-138

Without pallet truck Auction-ID: A1-46045-247

Without pallet truck Auction-ID: A1-46045-246

Auction-ID: A1-46045-139

Total height container 390 cm! Equipped with: 4000 liter fuel diesel tank (empty)( 3450x1250x2000 mm) Including: 20ft container. Auction-ID: A1-43429-70

40kvA current power; 1,500 rpm; 4-cylinder Deutz engine oil-cooled; 3.1l displacement; Linz-Stamford Generator; AC output: 1 x 400V 32A, 1 x 400V 16A, 1 x Schuko 16A, 1 x Schuko 230V; Electric starter; Power failure detection AMF (Automatic Mains Failure); Automatic Switch Transfer (ATS) emergency power system; Operating time at 50% output approx. 28 hours (157l tank capacity); Auction-ID: A1-46030-12

30kvA current power; 1,500 rpm; 4-cylinder Deutz engine oil-cooled; 3.1l displacement; Linz-Stamford Generator; AC output: 1 x 400V 32A, 1 x 400V 16A, 1 x Schuko 16A, 1 x Schuko 230V; Electric starter; Power failure detection AMF (Automatic Mains Failure); Automatic Switch Transfer (ATS) emergency power system; Operating time at 50% output approx. 28 hours (157l tank capacity); Auction-ID: A1-46030-14

Key data: 2 KW

Multifuel 1Wartsila 19.5 MW CHP Power Plant with 2 × 20V34DF (2021) This 19.5 MW multifuel (Gas / HFO / LFO) combined heat and power (CHP) plant is equipped with two Wartsila 20V34DF generating sets and exhaust gas heat recovery boilers. The plant was commissioned at the end of 2022 and has accumulated approximately 20,000 operating hours since new. All operation and maintenance activities have been performed by the Wartsila OEM Service team, ensuring that both the generating sets and auxiliary systems are maintained according to standards and remain in near-new condition. The plant is currently fully operational, available for immediate delivery, and can be load-tested for qualified buyers. The scope of delivery includes complete mechanical equipment capable of producing 19.5 MW of electrical power, 9.0 tons/hour of saturated steam at 10 bar and 8 MW of 90C hot water . In ad ...

Viewing by appointment Working condition Auction-ID: A1-43890-27

Max snhelness: 2000, 20 LBS, diesel. Auction-ID: A1-40136-275

Unaudited Good condition Auction-ID: A7-46327-195

max. wheel diameter:275 mm gear width:55 mm max. module:6,5 min. module:1,5 Face Hobbing-Continious Process Continuous process: The workpiece and tool (usually Spiron) rotate at the same time, and all teeth are created in one operation at the same time. Knife head has several knife groups (not arranged in a circle) Parallel tooth Conical tooth tip surface Single Item procedure: The workpiece is stationary and the tool (usually Arcon) rotates and cuts a tooth by immersing the tool. Once a tooth is cut, the tool moves out of the tooth again, the workpiece divides by one tooth width and the next tooth is cut until all teeth are finished. Knife head has arranged all knives in a circular path. Conical tooth height Parallel tooth head surface C28 can do both, wheel + pinion. However, a C28 must be ?prepared? for the individual part procedure. I.e. direct measuring system + part gear brake, w ...

max. wheel diameter:275 mm gear width:55 mm max. module:6,5 min. module:1,5 Face Hobbing-Continious Process Continuous process: The workpiece and tool (usually Spiron) rotate at the same time, and all teeth are created in one operation at the same time. Knife head has several knife groups (not arranged in a circle) Parallel tooth Conical tooth tip surface Single Item procedure: The workpiece is stationary and the tool (usually Arcon) rotates and cuts a tooth by immersing the tool. Once a tooth is cut, the tool moves out of the tooth again, the workpiece divides by one tooth width and the next tooth is cut until all teeth are finished. Knife head has arranged all knives in a circular path. Conical tooth height Parallel tooth head surface C28 can do both, wheel + pinion. However, a C28 must be ?prepared? for the individual part procedure. I.e. direct measuring system + part gear brake, w ...

max. wheel diameter:275 mm gear width: mm max. module: weight of the machine ca.:9,4 t dimensions of the machine ca.:3,7 x 3 x 2,82 m min. number of teeth:5 max. number of teeth:2000 range of tooth size:20 mm max. gear width (internal machining):58 mm X-axis:325 mm y-axis:350 mm Z-axis:475 mm Bevel gear milling machine Gleason Pfauter including Promot Automation

Steam generator PS400-60, electric heated stainless steel steam generator year of manufacture 2022, Factory inspection with the manufacturer 2026, 400 V / 60 kW / 50 Hz, 2-stage switchable (30 + 30 kW), max. operating pressure: 5 bar, adjustable operating pressure: 0 - 4 bar, max. steam amount: max. 84 kg/h (calculated value under optimal conditions), on a mobile frame, 1. Mechanical construction, The pot body is made of stainless steel 1.4571 and electrically welded. In, Kettle bodies are heating elements screwed in. The kettle body is located in a, Stainless steel housing and is clad with thermal insulation. In the stainless steel housing, the control cabinet is also located here. fittings (e.g.: steam outlet, water inlet,, etc.) lie outside the housing, 2. Functionality, Feedwater is pushed into the steam boiler by a water inlet valve. Is, when the intended water level is reached, the ...