tur 50 2000 used for sale

This 3-axis DN solutions LYNX 2100LMSA was manufactured in 2022. It features a maximum turning diameter of 300 mm and a turning length of 510 mm. The machine includes a 6-inch chuck size, a 12/24 station turret, and a sub-spindle for enhanced capabilities. If you are looking to get high-quality turning capabilities, consider the DN Solutions LYNX 2100LMSA horizontal turning machine we have for sale. Contact us for further details.

Nakamura NTJ-100Year of manuf. : 2015 Control : Fanuc 31i-B Turning diam. : 175 mmTurning length : 678 mm____________Description:In General:Year of manufacture:2015Control system:Fanuc i 31-BTurning diameter:175 mmMax. turning length:678 mmSpindle:Technology:Motorised spindleSpeed:4,500 rpmPower:11 kWBar capacity:65 mmC-axis:0.001°Clamping cylinder:Hollow clamping cylinderChuck:Collet chuckSub spindle:Technology:Motorised spindleSpeed:5,000 rpmPower:7.5 kWBar capacity:51 mmC-axis:0.001°Clamping cylinder:Semi-hollow clamping cylinderChuck:Collet chuckTool carrier I (X/Y/Z/B):Technology:Tool turretNumber of stations:12/24Tool holder:BMTTool drive:6,000 rpmX-axis:330 mmY-axis:80 mm (+/- 40 mm)Z-axis:1,040 mmB-axis:182° (+/- 91°)Tool carrier II (X/Y/Z):Technology:Tool turretNumber of stations:12/24Tool holder:BMTTool drive:6,000 rpmX-axis:127 mmY-axis:65 mm (+/- 32.5 mm)Z-axis:678  ...

Horizontal turning machine manufactured in 2008. This Weiler E50x2000 features a center distance of 2000 mm and a swing over bed of 570 mm. It has a spindle bore of 83 mm and a maximum torque at the spindle of 1600 Nm. Fully overhauled in 2026, it includes significant upgrades for enhanced performance. If you are looking to get high-quality turning capabilities, consider the Weiler E50x2000 machine we have for sale. Contact us for further details.

Horizontal turning machine manufactured in 2001. This Monforts RNC 400 A features a swing over bed of 410 mm and a turning length of 600 mm. It is equipped with a 12-position disc turret and a powerful three-phase induction motor with a speed range of 30-4000 rpm. If you are looking to get high-quality turning capabilities, consider the Monforts RNC 400 A machine we have for sale. Contact us for further details.

Horizontal turning machine manufactured in 2000. This Monforts RNC 400 AC features a turning length of 600 mm and a swing over bed of 410 mm. It is equipped with a 12-station disc turret and a maximum spindle speed of 4000 rpm. If you are looking to get high-quality turning capabilities, consider the Monforts RNC 400 AC machine we have for sale. Contact us for further details.

WEILER LZ330 / From educational institution incl. new 3-axis digital display -Turning diameter over bed 330mm -Turning diameter over support 165mm -Turning length 800mm -Speed range 25 - 2800 rpm -Automatic / longitudinal plan feeds -Multifix with 3x inserts -Drive power 3KW -Three-jaw chuck -Collet device with 20x collets -Copying device -Miscellaneous Accessories -Documentation Dimensions: LxWxH 1.8x0.7x1.6 meters / Weight 750Kg

Control MITSUBISHI M 700 Bar Passage 37.5 mm 2 x 12-speed revolver with attached revolver Wkz. 2 x C-axis 2 x Y-axis Main/sub-spindle FMB Bar Loading Magazine turbo 3-36 Knoll Coolant Preparation KF 10 Chip conveyor Renishaw Probes Parts catcher Conveyor belt for precast elements Air filter 2 x Collet Chuck Tool holders and collets

Passenger Car Off-Road Vehicle INEOS Grenadier 3.0 Turbo Petrol Engine 4x4, Former Characteristic GÖ-WR 94, EZ 08.08.2023, 43.539 abgl. Km (04.05.26), 2,998 cm³ Petrol, 210 kW, EURO6, VIN: SC6GM1AA4PF002794, Exterior color black, AHK permissible 3,500 kg, aluminum rims w. All-Terain T/A tires 19 inches, leather interior, heated front seats, winch 4.5t retrofitted 02/24 for approx. ? 5.283,- net at the dealer, roof rack retrofitted 02/25 for approx. ? 2.839,- net at the dealer, notification of maintenance overdue 2.049 days (has not been deferred), last service at 34.927 km 09/25 (invoice is available), 2 keys, 1 previous owner,

Never used Three (3) units of used 6 MW gas turbine model: MGT6000 - Built in 2019, last preservation in 2021.

\" Lot of approx. 300 kg of turning steels – mixed lot for lathes An extensive lot of turning steels for machine tools is for sale. Inventory according to visual inspection: • External turning steels • Internal turning steels / boring rods • Parting steels • Shaped steels • Partly equipped with carbide • Partly with indexable insert holders Different dimensions and designs. Sale exclusively as a total item. Total weight: approx. 300 kg Material: tool steel / partly carbide tipped Design: various shaft sizes and lengths \" Auction-ID: A7-46417-369

\" Conventional lead and tension spindle lathe – turning length approx. 1,200 mm – Ø 475 mm Chuck lead and tension spindle lathe made by Boehringer Bros. (VDF), industrial version. Equipment: • 3-jaw chuck Ø 475 mm • Tailstock • Rotating center punch • Extensive accessories in the side cabinet (jaws, holders, inserts, etc.) • Coolant device • Controls on the support Turning length approx. 1,200 mm.Condition: Used machine with age-related signs of use. Visually appropriate to the age. Manufacturer: Gebr. Boehringer GmbH Type: Lead and pull spindle lathe Turning length: approx. 1,200 mm Chuck diameter: Ø 475 mm Spindle bore: approx. 80 mm • Dimensions in mm (LxWxH) approx. 3,450 x 1,300 x 1,700 mm \" Auction-ID: A7-46417-373

Engine overhaul 10000 Gearbox reserved in 2024 Double wheels available Air conditioning available Air suspension seat Auction-ID: A3-43524-11904

Key data: 430 mm, 1400 mm

Guide and pull spindle 32 A 380V 12.5 KW Speeds 18 - 1400 rpm Spindle passage 90 mm Lamp 4-way quick coupler with 14 pick-ups 3 interchangeable jaw sets Röhm Jaw Chuck with 33 cm Bezel Length 1.10 m Width 3 m Height 1.40 m Weight 2.5 T

This 7-axis Citizen Cincom A320-VII mod. A20-3F7 was manufactured in 2019. It features a maximum workable diameter of 20 mm, with an option for 25 mm, and a maximum workable length of 200 mm. The machine is equipped with a Fanuc 32i CNC control and includes a bar feeder, high-pressure coolant system, and a chiller. If you are looking to get high-quality turning capabilities, consider the Citizen Cincom A320-VII machine we have for sale. Contact us for further details.

This 6-axis Index ABC 63 was manufactured in 1999. It has a rated power of 13 kW and a machine weight of approximately 2100 kg. If you are looking to get high-quality turning capabilities, consider the Index ABC 63 horizontal turning machine we have for sale. Contact us for further details.

Key data: 280 mm, 400 mm

Technical data: Manufacturer: Spinner Type: TC 52 MC Year of Make: 2007 Control: Siemens 810D Shop Turn Travels: X 200 mm, Z 570 mm Switch-on hours: 4,364 h Turning diameter: max. 280 mm Circumferential diameter: max. 400 mm Main spindle Speed: 5,000 rpm Spindle passage: 52 mm Tools Revolver: 12-speed Tool holder: VDI 30 Number of driven tools: all Dimensions and weight Weight: approx. 3,500 kg Condition Condition: Used Functional: Tested and fully functional Other equipment and accessories included: Chip conveyor Interface for bar feeders 3-jaw chuck

equipped with: towing pickup, no knives, towing eye tightening, hydraulic drawbar, hydraulic unloading valve, floor chain, Dutch registration registration, Auction-ID: A1-40137-204

(PLEASE NOTE! this vehicle has a license plate registration, when you pick it up you must register it on the spot with a third party or export it, there are extra costs involved) Auction-ID: A1-42016-215

Horizontal turning machine manufactured in 2006. This Johnford SL60 features a swing over bed of 580 mm and a spindle bore of 76.5 mm. It is equipped with a 12-station tool turret and a high-torque spindle motor capable of speeds up to 3,500 rpm. If you are looking to get high-quality turning capabilities, consider the Johnford SL60 machine we have for sale. Contact us for further details.

This 3-axis Okuma Genos L300 E-M was manufactured in 2014. It features a maximum turning diameter of 300 mm and a turning length of up to 1000 mm. The machine is equipped with a spindle speed of up to 3800 rpm and a robust turret with 12 stations. If you are looking to get high-quality turning capabilities, consider the Okuma Genos L300 E-M CNC lathe we have for sale. Contact us for further details.

This 3-axis WEMAS DZ 270 was manufactured in 2002. It features a turning diameter of 300 mm and a turning length of 754 mm. The machine is equipped with a HEIDENHAIN control unit and a 12-station disc turret from DUPLOMATIC, allowing for efficient tool management. If you are looking to get high-quality turning capabilities, consider the WEMAS DZ 270 horizontal turning machine we have for sale. Contact us for further details.

Horizontal turning machine manufactured in 1998. This PADOVANI E255/1500 features a spindle motor with a power of 11.5 kW and a total mounted power of approximately 14 kW. The machine has a length of 3535 mm and a width of 1800 mm, with a weight of 2500 kg. If you are looking to get high-quality turning capabilities, consider the PADOVANI E255/1500 machine we have for sale. Contact us for further details.

This 6-axis AMADA Wasino JJ3 was manufactured in 2007. It features a twin spindle, twin turret turning cell with a maximum spindle speed of 4000 rpm and a chuck size of 8”. The machine is designed for high-volume production with automatic loading and unloading capabilities. If you are looking to get high-quality turning capabilities, consider the AMADA Wasino JJ3 horizontal turning machine we have for sale. Contact us for further details.

CONTROLS   CNC controls NUM 1060 WORKING RANGE TURNING   swing diameter (max): 2000 mm   workpiece weight max.: 25000 kg CROSS BEAM SLIDE   - rotation speeds (min): 2 /min   - rotation speeds (max): 450 /min ELECTRICAL SPECIFICATIONS   mains voltage: 400 V   mains frequency: 50 Hz DIMENSIONS / WEIGHTS   space requirements -left/right-: 4100 mm   space requirements -front/back-: 3500 mm   total height: 5600 mm

The machine is in good technical condition, after prior agreement it is possible to test it. with a bar seller, 65 mm draw tube passage, Sauter revolver, driven tools, hydraulic tailstock, it is after GO, new draw cylinder for clamping tools, still connected in operation, including draw tube inserts, tool holder, etc.,

Key data: 350 mm, 650 mm, 3500 1/min

CNC Teach-in Lathe COLCHESTER Alpha 1350 XT CNC FANUC Between points: 650 mm Maxi turning diameter: Ø 350 mm Spindle diameter: Ø 42 mm Rotation max: 3500 RPM Turret: 8 tools Year of construction: 2006 Working hours: 174 working hours only MACHINE IN VERY GOOD CONDITION

equipped with 750/1000 rpm PTO, sprung front axle, suspended cabin, air superstructure, tipping knob, carriage catch mouth, top link, linkage, fender control, load sensing, 3- and 7-pin plug connection, engine brake, Auction-ID: A1-40137-50

Fendt 308 lsa 40kmh; Digital Dashboard; hydro brake valve; 540/750/1000 PTO; ROOF HATCH! Auction-ID: A1-40137-157

Auction-ID: A1-46501-3101

Features: Toro eTimeCutter, eMR4275 Zero-Turn Riding Mower, (Model 75642) with 60V Flex-Force Power System, All-Electric Riding Mower Features 107 cm (42 in) Cutting Width, IronForged Two-Blade Mower Deck, MyRIDE Suspension, 6 Battery Outlets, Electric Drive Reduces Maintenance and Quieter Operation Compared to Gasoline Models, LED Headlights, Digital Hour Meter, Cup Holder and Side Ejection, mulching function, suitable for flat terrain with obstacles and ideal for medium to large lawns, cutting width: 107 cm (42 inches), dimensions (L x W x H): approx. 208 x 125 x 89 cm, number of battery connections: 6, number of batteries: 6 (60V, 10.0 Ah), charging time: approx. 160 minutes, power: 60V Max (Flex-Force system), number of blades: 2, cutting height: 3.8 – 11.4 cm, Forward speed: up to 11.2 km/h, reverse speed: up to 4.8 km/h, this is a new product. Auction-ID: A1-40137-189

Original Kanuk Turbo 2 workshop stove for carpentry etc. approx. 1.30m long x 0.60m wide x 1.10m high with blower with ash bucket, with air distribution pipe, with chimney connection technical data see nameplate under pictures good condition 2.5 years old Loading onto trucks and dismantling subject to a fee Auction-ID: A1-46501-2026

working machine, start and mower deck switches on. Auction-ID: A1-40137-287

Power: PTO-driven; diaphragm pump 75 L/min Operating parameters: Air velocity 38 m/s (137 km/h); fan Ø 712 mm; vertical spray reach up to 8 m; horizontal reach 4 m (each side); 14 nozzles; wt. 675 kg; dim. 3,780 x 1,590 x 1,490 mm Workpiece capacity: Main tank 1,500 L; rinsing tank 115 L; handwash tank 12 L; orchard & vineyard spraying Supported edges: Orchards, vineyards, tree crops Edge types: Air-assisted spraying; phytosanitary treatment Included equipment: Turbine air system; diaphragm pump 75 LPM; 14 nozzles; OM kit (4 hand guns); pressure control system; safety valves; adjustable axle/track system Compliance: Agricultural sprayer equipment Power supply: Tractor PTO Year/Manufacturer: Mahindra – AIROTEC TURBO 1500 Remarks: Compact, highly maneuverable sprayer with adjustable track width/height; suitable for tight orchard/vineyard operations 1,500 L air-a ...

Engine 3-cylinder Kubota 26 HP. Hours: 2811 hours. Hydrostatic drive. Cutting width 152 cm. Auction-ID: A1-40137-301

Equipped with 4-Cil. \"MWM\" Diesel engine; PTO shaft 540/750/1000 rpm; adjustable tow bar; 2 double-acting hydraulic valves; top link; Auction-ID: A1-40137-170

Power: PTO-driven sprayer; diaphragm pump 75 L/min Operating parameters: Air velocity 38 m/s (137 km/h); fan Ø 712 mm; vertical spray reach up to 8 m; horizontal reach 4 m (each side); 14 nozzles Workpiece capacity: Main tank 2,000 L; rinsing tank 145 L; handwash tank 20 L; orchard & vineyard spraying Supported edges: Orchards, vineyards, tree crops Edge types: Air-assisted spraying; phytosanitary treatment Included equipment: Air conveyor turbine system; diaphragm pump 75 L/min; 14 spray nozzles; OM kit with 4 hand guns; pressure control system; safety valves; rubber couplings; hot-dip galvanized components Compliance: Agricultural sprayer equipment; safety pressure relief valves Power supply: Tractor PTO Year/Manufacturer: Mahindra – AIROTEC TURBO 2000 Remarks: Compact tank design with efficient air distribution; adjustable track width/height; designed for uni ...

Horizontal turning machine manufactured in 1999. This Weiler E35 D features a Siemens Sinumerik 810D control with Weiler D1 user software and a 12.1-inch TFT color flat screen. It includes a coolant unit with a flow rate of 30 l/min and a tool holder for quick-change operations. If you are looking to get high-quality turning capabilities, consider the Weiler E35 D machine we have for sale. Contact us for further details.

This 4-axis Okuma LU15 M-2SC 1000 was manufactured in 1998. It features two tool turrets, live tooling with C-axis capabilities, and synchronous tapping for enhanced productivity. The machine includes an integrated tool setter for precise measurements and a programmable tailstock for versatility. If you are looking to get high-quality turning capabilities, consider the Okuma LU15 M-2SC 1000 horizontal turning machine we have for sale. Contact us for further details.

DMG MORI CL2000A CNC turning center was built in 2017 in Japan by DMG MORI CO., LTD. The machine is new and has never been used. The DMG MORI CL2000A is an excellent choice for the production of high-precision and repeatable parts used in many industrial sectors. This compact yet extremely powerful lathe will excel in even the most demanding production challenges. All machining processes, i.e. precision turning or threading, are performed fully automatically by means of the spindle and the cutting tools, taken from a 10-position turret. The spindle, driven by a high-powered motor, rotates at a maximum speed of 4500 rpm and operates in two X,Z axes with feeds of 245 mm and 370 mm respectively. What’s more, the machine’s design is based on the Finite Element Method (FEM). This solution guarantees the maintenance of high geometrical accuracy of the design, even under heavy loads.  ...

Key data: 290 mm, 450 mm, 5000 1/min

Control: EPL Country of origin: Germany Spindle passage: Ø65 mm Tool turret: 12-fold driven places Tool holder: VDI 40 Speed tools: 3000 rpm Weight: approx. 4,700 kg + 600kg control cabinet Chip conveyor: BMF Bürener Maschinenfabrik Bar feeder: GIOVANNI CUCCHI, type DB 70 Tools for an extra charge There are a total of 6 machines with bar feeder (price per machine with loader) Dcjwvey N Tdzeu Nu Ieg There is 1 machine without loader available (€ 8.500,-)

This 3-axis Gildemeister CTX 400 Serie 2 was manufactured in 2002. It features a spindle speed of up to 5,000 rpm and a z-axis travel of 635 mm, along with an x-axis travel of 570 mm over the bed. The machine includes a 12-position turret and is equipped with a 3-jaw chuck, chip conveyor, and coolant system. If you are looking to get high-quality turning capabilities, consider the Gildemeister CTX 400 Serie 2 machine we have for sale. Contact us for further details.

This 5-axis MORI SEIKI SL-153 SMC was manufactured in 2000. It features a maximum X-axis travel of 230 mm and Z-axis travel of 520 mm. The machine includes a hydraulic chuck system, chip conveyor, and multiple driven tool holders for enhanced machining capabilities. If you are looking to get high-quality turning capabilities, consider the MORI SEIKI SL-153 SMC horizontal turning machine we have for sale. Contact us for further details.

CNC Swiss lathe GILDEMEISTER SPRINT 20/8 linear With Fanuc 31i controller Year of Make: 2016 Spindle bore: 20 mm MAIN SPINDLE Turning diameter: max. 20 mm Speed range : max. 10000 rpm Stroke Z1: 80 mm SUB-SPINDLE Turning diameter: max. 20 mm Stroke Z 2 : 300 mm Speed: max. 10000 rpm SLIDE 1 Stroke X 1: 50 mm Stroke Y 1: 350 mm 6 Pos. Tool Holder 12 x 12 5 rotating tools including spindles with clamp holder ESX 16 SLIDE 2 Stroke x 2 : 240 mm 4 position tool holder for external machining with connection 12 x 12 4 position tool holder for internal machining diameter 20 mm 5 rotating tools including spindles with clamp holder ESX 16 6 + 2 axes, 2 Y axes as standard Linear actuator for maximum precision With the following accessories: Full protection cab with interior lighting Various tool holders C axis for main and counter spindle Bar Feeder L ...

CNC Swiss lathe GILDEMEISTER SPRINT 20/8 With Fanuc 32i control Year of manufacture: 11/2019 Spindle bore: 20 mm MAIN SPINDLE Turning diameter: max. 20 mm Speed range : max. 10000 rpm Stroke Z1: 60 mm SUB-SPINDLE Turning diameter: max. 20 mm Stroke x 2 : 220 mm Stroke Z 2 : 170 mm Speed: max. 10000 rpm SLIDE 1 Stroke X 1: 50 mm Stroke Y 1: 325 mm SLIDE Y 2 Stroke Y 2 : 85 mm With the following accessories: Full protection cab with interior lighting Various tool holders Tool holder for slides 1-3 4 driven tools with 4 spindles with ESX/ER 16 holder C axis for main and counter spindle Y axis on carriage 1 – 2 2 cross slides Workpiece unloading conveyor Signal light 4 colour Fire extinguishing system Coolant device 165 l ( Pumping capacity 90 l/min 1 bar) THE MACHINE IS IN MINT CONDITION THE MACHINE HAS ONLY 110 PROGRAM RUNNING HOURS

Excellent condition - Fully operational - Loading / Transport possible! Twin spindle Swing over bed: 530 mm Turning length: 330 mm X-Axis travel: 210 mm Z-Axis travel: 310 mm Rapid traverse: 30 m/min Spindle speed: 8000 Rpm Spindle configuration: A2-4, 5C Spindle bore: 27 mm Turret type: VDI 25 Live tool speed: max. 6000 Rpm Number turret positions: 16 Control: GE Fanuc Series 18i-TB Incl various tool holders a.o. 6x driven toolholders Note! No tooling Bar Feeder: BARLOAD Type: Hydrafeed BA 65 S/N: 16080043 Year 2009 Bar length: 1200 mm Bar diameter: 5-65 mm Bar capacity: 10 pcs (65 mm) Dimensions: 1910x1000x1250 mm Weight: 320 kg

Excellent condition - Fully operational - Loading / Transport possible! Workpiece: Max. clamping diam. 26 mm 9 main spindles: Spindle 1 to 6: rated torque 18,5 Nm max. torque 50 Nm Max. speed 7,000 rpm Spindles 7 to 9: rated torque 15 Nm max. torque 30 Nm Max. Speed 10,000 rpm Travels (cross slide): X (spindles 1 to 6): 70 mm X (spindles 8 to 9): 110 mm Z: 125 mm Feeds: 30 m/min Feed power: 3kN Travels (longitudinal slide): X: 16 mm Z: 300 mm Feed power 3kN Feeds: 30 m/min CNC Siemens 840 D Swarf conveyor and chiller 21,1 Kw Knoll chiller With CUCCHI compact bar feeder 26 mm (rounded), 19 mm (squared), 22 mm (hexagonal) bar length: 4200 mm

used MORI SEIKI NL 2500/1250 CNC lathe, manufactured in 2006, is for sale. It is equipped with a MORI SEIKI MSX 850III / MAPPS III control system and an IRCO SIMAG loading magazine for automatic bar feeding. | Technical specifications | Control system: MORI SEIKI MSX 850III / MAPPS III | Country of origin: Japan | Type: Slant-bed CNC lathe | Centre distance: 1,250 mm | Max. turning length: 1,298 mm | Max. turning diameter: 356 mm | Standard turning diameter: 275 mm | Swivel diameter over bed: 923 mm | X-axis: 260 mm | Z-axis: 1,345 mm | Spindle speed: up to 4,000 rpm | Spindle bore: approx. 80 mm | Turret: 12-station | Number of turrets: 1 | Chip conveyor | Powered tools | C-axis | Y-axis | Machine weight: 7,600 kg | Machine dimensions: 5,000 x 2,300 x 2,400 mm | The machine can be viewed in operation by appointment. | Subject to changes and errors in the technical data and specification ...

Year of manufacture: 2018 | Condition: Very good, ready for operation | Availability: Short notice | Brief description | A Citizen Miyano BNE-51MSY CNC short turning machine in MSY design with main and counter spindle and Y-axis is for sale. | Features/highlights | Y-axis | 2 tool turrets, each with 12 stations | Driven tools | Simultaneous machining possible | High rigidity and process reliability | Technical data | Max. bar capacity: Ø 51 mm | Max. turning diameter: approx. 165 mm | Max. turning length: approx. 380 mm | Main spindle speed: up to approx. 5,000 rpm | Counter spindle speed: up to approx. 5,000 rpm | Control: Mitsubishi MELDAS | Machine weight: approx. 8,000 kg | Machine fully functional, both electrically and mechanically | Complete technical documentation available | The machine can be viewed by appointment. | Subject to changes and errors in the technical data and spec ...

Year of manufacture: 2012 | Spindle hours: 20,000 | Turning diameter (max.): approx. 390 mm | Turning length (max.): 1,250 mm | Bar capacity: 76 mm (standard) | X-axis: 300 mm | Z-axis: 1,250 mm | Y-axis: +/- 60 mm (on upper turret) | Spindle specifications: | Speed: up to 5,000 rpm | Drive power: 34 kW (40% duty cycle) | Torque: up to 380 Nm | 4-axis kinematics | 2 x 12 stations (all stations suitable for powered tools) | Speed up to 6,000 rpm, power 11.3 kW | Gear cutting software, including specialised tool holders for gear hobbing/cutting. | IRCO MUK short loader | Hinged belt chip conveyor | 20 bar high-pressure system with paper belt filter | We reserve the right to make changes and correct errors in the technical data, and to sell items prior to order!

Year of manufacture: 2011 | Machine operating hours: 56,000 hrs | Machine automatic cycle hours: 48,000 hrs | FANUC 31i CNC control – Model A, 7-axis | Technical data | - Number of axes: 7 | - Number of spindles: 2 | MAIN SPINDLE | - Max. bar diameter: 60 [mm] | - Spindle speed: 5000 [rpm] | - Spindle drive power: 7.5 [kW] | COUNTER SPINDLE (on the turret) | - Max. bar diameter: 42/ (60) [mm] | - Spindle speed: 5000 [rpm] | - Spindle drive power: 3.7 [kW] | Powered tools (turret): | Tool drive power: 3.7 kW | Max. speed: 6,000 rpm | Rear-end machining: | 4 fixed tool stations | Up to 14 tools / capacity possible | Bar loading magazine FMB Turbo 5-55 / 3200 / A | Year of manufacture: 2008 | Bar diameter: 5 - 55 [mm] | Bar length: 3,200 [mm] | Chip conveyor | The machine can be viewed by appointment. | Subject to changes and errors in the technical data and specifications, as well as pri ...