We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree
122,047 used machines on RESALE, but how to find them? Machine Search
maximum number of results exceeded > 1000
please refine your search
used
Key data: 1200 , 1500
ENGINE RUNNING HRS : 25,916 and SERVICED RATED POWER : 1,2 MW MAXIMUM AMBIENT TEMP : 25 C RATED FREQUENCY : 50 HZ RATED VOLTAGE : 400 V RATED CURRENT : 1,732 A MASS : 11,735 GENERATOR DETAILS: MAKE : LEROY SOMER ALTERNATORS PARTNER LSA : C 50.2VL10B C 6S FREQUENCY : 50 HZ SPEED : 1500 RPM PROTECTION : IP23/4 POWER FACTOR : 0.80 INSULATION CLASS : F A.V.R : R448-V50 + 7AREP ALTITUDE : < 1000 M MASS WEIGHT : 3300 KG HEAT EXCHANGER DETAILS: MAKE : ARRA (A.S.T.R.A. REFRIGERANTI) DESIGN PRESSURE (TUBE SIDE) : 5 BAR DESIGN PRESSURE (SHEEL SIDE) : 4.5 BAR TEST PRESSURE (TUBE SIDE) : 7.5 BAR TEST PRESSURE (SHEEL SIDE) : 6.75 BAR DESIGN TEMP (TUBE SID ...
new
tube diameter: 42,0 mm Stahl wall strength: 3,0 mm Stahl tube diameter: 54,0 mm CU/Alu wall strength: 2,0 mm bar material - diameter: 30,0 mm revolutions per minute: 2,0 U/min voltage: 400 Volt total power requirement: 1,1 kW weight: 80,0 kg range L-W-H: 410 x 1000 x 570 mm ERCOLINA MediBender MB 42 M - Capacity steel tube 42 x 3.0mm - Gas tube capacity 11/4 gas x 3.5 mm - Capacity square profile (FE 42) 35 x 35 x 3 mm - Max. bending radius 10-260 mm - Minimum radius 2 x D - Hex tool holder - Min. outer diameter 5 mm - 1/8 gas Furnishing : - Patented quick tool change system - a bending speed - free-moving footswitch including ERCOLINA microprocessor control: - with 30 programs (0 - 29) - Each program can be programmed with up to 9 bending angles - In addition, in the work mode for each bending angle necessary correction angle must be entered The data for this ad was created with Modu ...
new
Complete dosing and packaging system for liquids including 150 liter tank with stirring device and twin piston pump. AMTEC P60L vertical packaging machine with vacuum film pulling belts and MITSUBISHI PLC and WEINVIEW touchscreen. PE sealing system (recommended film: PE Co Extrud. 3 Layer LLDPE). - Specifications: bag size: L(100-300)xW(80-240)mm | max. filling volume: 1.5 liter | max. speed of the machine in neutral: 40 cycles/min | tank: including stirrer, 150 liter, SS304 stainless steel | twin piston pump: stainless steel tube SS304, outlet tube diameter: 167mm, inlet tube diamter: 158mm, thickness 9mm, piston pump tube length: 370mm, about max. 1,5 liter liquid | stainless steel ball valve SS316 | stainless steel nozzle SS304 | teflon outlet | dimensions and weight: L1550xW1160xH1480mm, 480/600kg (machine), L1000xW1000xH1800mm, 150/200kg (tank). Please note that our new prices are o ...
used
Enigines stopped end Overhauled never run after again. Rated power 1,2 MW MAX ALTITUDE OF INSTALLATION : 500 M MAXIMUM AMBIENT TEMP : 25 C RATED FREQUENCY : 50 HZ RATED VOLTAGE : 400 V RATED CURRENT : 1,732 A MASS : 12,025 KG 2. GENERATOR DETAILS: MAKE : LEROY SOMER ALTERNATORS PARTNER LSA : C 50.2VL10B C 6S/4 DATE : 2013/21 FREQUENCY : 50 HZ SPEED : 1500 RPM PROTECTION : IP23/4 POWER FACTOR : 1.0 INSULATION CLASS: H/F A.V.R : R450 EXCITATION : AREP ALTITUDE : < 1000 M MASS WEIGHT : 3300 KG HEAT EXCHANGER DETAILS: MAKE : ARRA (A.S.T.R.A. REFRIGERANTI) DATE : 07/09/2012 DESIGN PRESSURE (TUBE SIDE) : 5 BAR DESIGN PRESSURE (SHEEL SIDE) : 4.5 BAR TEST PRESSURE (TUBE SIDE) : 7.5 BAR TEST PRESSURE (SHEEL SIDE) ...
used
Offer 23397 Specifications: - Saw blade diameter up to 350 mm - 2 saw blade spindle speeds 22 + 44 rpm - Mitre adjustable left + right up to 45 ° - Cutting range at 90° - round tube 115 mm - Square tube 105 x 105 mm - Solid material (saw blade 350mm) 60 mm - Flat profile 140 x 80 mm - Cutting range at 45° - round tube 115 mm - Square tube 90 x 90 mm - Pneumatic material clamping vices - Coolant device - Dimensional fence 1500 mm - Pneumatic connection 6 bar - Drive 400 V / 1.4 / 2.2 kW - Space requirement approx. W 600 x H 1400 x D 900 mm - Weight approx. 300 kg
used
Hydraulic mandrel bending machine with a lot of accessories Preselection of 8 different bending angles with digital display Digital length display as well as digital display of torsion Max. effective length: 6096 mm Round tube steel (S 235): 60.0 x 6.0 mm Round tube stainless steel (S 355): 60.0 x 4.0 mm Square tube steel: 50 x 50 x 4.0 mm Rectangular tube steel: 60 x 40 x 2.0 mm Max. bending angle: 180° Weight: approx. 1800 kg
used
Scheugenpflug DOS P016 Piston Feeder Piston dosing system DOS P for a wide range of requirements The piston dosing systems from Scheugenpflug work according to the principle of volumetric dosing, i.e. the dosed amount of material is mechanically determined by the geometry and stroke of the associated cylinders. The cylinder is filled with the potting material by feeding it from the corresponding material conveyor system. If a two-component medium is used, the volume of the two cylinders simultaneously determines the ratio of the resin and hardener components to each other. The dosing pistons simultaneously push the two components in separate channels towards the exhaust valve, where they only mix in the static mixing tube to form a homogeneous reactive medium. The Dos P016 / 050 / 100 / 300 / TCA piston dosing systems are high-precision volumetric dosing systems designed for pr ...
used
external wort boiler for brewhouse 130 hl knockout capacity;, Additional title: tube and shell heat exchanger, Pressure shell/tube: 2 bar, Volumke shell/tube: 200 l, Material: stainless steel AISI 321, Base construction: vertical tube and shell heat exchanger with compensator and with support, Features: Steam- and condensate fittings; safety valvel
used
General SKU358T1079 LocationBarneveld MakeOKKN Sudhess Rohrleitungsbau GMBH No.2689 & 2718 Year of construction2689: 2015: 2718: 1986 Pressure Vacuum possiblecheck Working pressure shell10 Bar Working pressure tubes6.5 Bar Tubular vacuum possiblecheck Main Features Shell (Material)Stainless steel Tube (Material)Stainless steel Surface45.6 m2 Specified Features - Distillation MaterialStainless steel 1.4571 (316Ti) Distillation Heat exchangercheck Verticalcheck Heating surface45,6 m² Tube capacity300 Ltr. Number of tubes:484 Tube diameter25 mm Tube length1200 mm Wall thickness tubes2 mm Max. temperature0/250 °C Shell capacity200 Ltr. Shell diameter800 mm Shell length1200 mm Wall thickness shell5 mm Max. temperature0/250 °C Shell with expansion jointcheck Shell connectionsDN100 (2x) Information Floorspace1,6x1,6 m Total height11,5 m Weight4490 kg Ex ...
used
Used 5800 litre / 1276 gallon Vertical Stainless steel 316 Mixing Tank / Vessel with Hopper Manufacturer: No Nameplate Details Connections TOP 1 x 900x860mm Top Hopper access complete with hinged lid 1 x 4” Treaded Tube (Externally), Inlet 1 x Ø250 Open Tube Inlet 2 x Ø270 Open Tube Inlet 1 x Ø300 Top Centre Mixer Enrty, Open tube. SIDE 2 x Lift Lugs BASE 1 x 4” Flange Outlet Complete with Branch Outlet: 2” Ball Valve with Bauer Union. Tank supported by S/S Support Shoulders complete with 50x50mm S/S RSA strengthening Ring welded to shell. Tank has a Large Mixer Bridge support Mount from 160x90mm Mild Steel Box Mounted on tubular S/S uprights from Vessel. Tank has Internal Fully body Baffle Plates fitted. No Mixer currently fitted.
used
Used 5800 litre / 1276 gallon Vertical Stainless steel 316 Mixing Tank / Vessel with Hopper Manufacturer: No Nameplate Details Connections TOP 1 x 900x860mm Top Hopper access complete with hinged lid 1 x 4” Treaded Tube (Externally), Inlet 1 x Ø250 Open Tube Inlet 2 x Ø270 Open Tube Inlet 1 x Ø300 Top Centre Mixer Enrty, Open tube. SIDE 2 x Lift Lugs BASE 1 x 4” Flange Outlet Complete with Branch Outlet: 2” Ball Valve with Bauer Union. Tank supported by S/S Support Shoulders complete with 50x50mm S/S RSA strengthening Ring welded to shell. Tank has a Large Mixer Bridge support Mount from 160x90mm Mild Steel Box Mounted on tubular S/S uprights from Vessel. Tank has Internal Fully body Baffle Plates fitted. No Mixer currently fitted.
used
Used 5800 litre / 1276 gallon Vertical Stainless steel 316 Mixing Tank / Vessel with Hopper Manufacturer: No Nameplate Details Connections TOP 1 x 900x860mm Top Hopper access complete with hinged lid 1 x 4” Treaded Tube (Externally), Inlet 1 x Ø250 Open Tube Inlet 2 x Ø270 Open Tube Inlet 1 x Ø300 Top Centre Mixer Enrty, Open tube. SIDE 2 x Lift Lugs BASE 1 x 4” Flange Outlet Complete with Branch Outlet: 2” Ball Valve with Bauer Union. Tank supported by S/S Support Shoulders complete with 50x50mm S/S RSA strengthening Ring welded to shell. Tank has a Large Mixer Bridge support Mount from 160x90mm Mild Steel Box Mounted on tubular S/S uprights from Vessel. Tank has Internal Fully body Baffle Plates fitted. No Mixer currently fitted.
used
Used 1850 Litre / 407 Gallon / Stainless Steel Jacketed Yeast Mixing Tank / Vessel - Stock Ref: CB6041 Manufacturer: No Nameplate Fittings: TOP 1 x 10½” O/D Mixer Pad 1 x 1” cut tube with internal sprayball 2 x 7” Sight Glass 1 x 2” RJT Male CIP with Large Sprayball (Top Centre) 1 x 1” Flange inlet 1 x 4” Overflow tube with 2” RJT Male at highest point. 2 x Mild Steel Lift Lugs SIDE 2 x 1” cut tube, Jacket connections 1 x 2” RJT Male inlet 1 x Temperature Socket Pocket 1 x 510x410 Oval side Manway 1 x 1” Valve with RJT Male BASE 1 x 4” RJT Female MIXER DETAIL: PLENTY LTD G/BOX, Model: PMG 110 Ratio: 5/1 RPM: 290 Year: 1987 BCP Motor: 1.1kW / 1420 rpm Tank Insulated 100mm Min with fully welded S/S Cladding all over. Tank supported on 4-Off tube legs.
used
Used 5800 litre / 1276 gallon Vertical Stainless steel 316 Mixing Tank / Vessel with Hopper Manufacturer: No Nameplate Details Connections TOP 1 x 900x860mm Top Hopper access complete with hinged lid 1 x 4” Treaded Tube (Externally), Inlet 1 x Ø250 Open Tube Inlet 2 x Ø270 Open Tube Inlet 1 x Ø300 Top Centre Mixer Enrty, Open tube. SIDE 2 x Lift Lugs BASE 1 x 4” Flange Outlet Complete with Branch Outlet: 2” Ball Valve with Bauer Union. Tank supported by S/S Support Shoulders complete with 50x50mm S/S RSA strengthening Ring welded to shell. Tank has a Large Mixer Bridge support Mount from 160x90mm Mild Steel Box Mounted on tubular S/S uprights from Vessel. Tank has Internal Fully body Baffle Plates fitted. No Mixer currently fitted.
used
Used 5800 litre / 1276 gallon Vertical Stainless steel 316 Mixing Tank / Vessel with Hopper Manufacturer: No Nameplate Details Connections TOP 1 x 900x860mm Top Hopper access complete with hinged lid 1 x 4” Treaded Tube (Externally), Inlet 1 x Ø250 Open Tube Inlet 2 x Ø270 Open Tube Inlet 1 x Ø300 Top Centre Mixer Enrty, Open tube. SIDE 2 x Lift Lugs BASE 1 x 4” Flange Outlet Complete with Branch Outlet: 2” Ball Valve with Bauer Union. Tank supported by S/S Support Shoulders complete with 50x50mm S/S RSA strengthening Ring welded to shell. Tank has a Large Mixer Bridge support Mount from 160x90mm Mild Steel Box Mounted on tubular S/S uprights from Vessel. Tank has Internal Fully body Baffle Plates fitted. No Mixer currently fitted.
used
Used 1850 Litre / 407 Gallon / Stainless Steel Jacketed Yeast Mixing Tank / Vessel - Stock Ref: CB6041 Manufacturer: No Nameplate Fittings: TOP 1 x 10½” O/D Mixer Pad 1 x 1” cut tube with internal sprayball 2 x 7” Sight Glass 1 x 2” RJT Male CIP with Large Sprayball (Top Centre) 1 x 1” Flange inlet 1 x 4” Overflow tube with 2” RJT Male at highest point. 2 x Mild Steel Lift Lugs SIDE 2 x 1” cut tube, Jacket connections 1 x 2” RJT Male inlet 1 x Temperature Socket Pocket 1 x 510x410 Oval side Manway 1 x 1” Valve with RJT Male BASE 1 x 4” RJT Female MIXER DETAIL: PLENTY LTD G/BOX, Model: PMG 110 Ratio: 5/1 RPM: 290 Year: 1987 BCP Motor: 1.1kW / 1420 rpm Tank Insulated 100mm Min with fully welded S/S Cladding all over. Tank supported on 4-Off tube legs.
used
Motor tube Notchers from ALMI AL1â2U Notching of gas -, steam -, stainless steel, non-ferrous, as well as numerous other pipes with heavy use, ALMI has developed a series of particularly efficient pipe Notchers with electric drive. Wherever ensure the Notcher ALMI extremely quickly and accurately for the correct tube recess where welded tubes at a 90 ° angle. They are suitable also for the production of double corner joints. The pipe Notchers with a 2.2 KW motor is equipped for intensive use. The engine forms a whole with special eccentric shaft, which drives the notching tool. The model AL1-2U also has a Notcher for zinc spout. The tube Notcher has a 0 voltage fuse, and a protection device. Properties High productivity Low investment costs Several diameter available immediately Ideal for double corner joints up to 5 mm wall thickness (for VA up to 4 ...
used
TOP STATE - OVERHAUL IN 2016! Year of construction: 2001 2D table format: 2500 x 1250 3D Max processing size: 900 mm x 2150 mm x 300 mm Power: 2000W Control: FANUC incl. cooler incl. 2D programming software + chamfer module + tube/profile module incl. training incl. commissioning incl. quick penetration incl. ball roller table with 3D cutting head incl. CNC tube axle tube and profile up to 160 mm diameter plates, chamfering 3D molded parts, tubes and profiles FE: up to 15mm Oxide-free VA: up to 8mm designed for high pressure cutting up to 20 bar no foundation required! Optional automatic loading and unloading by Mazak FMS48 is available always regularly serviced with warranty / commissioning / training
used
We offer you a railing post from SSI Shepherd for sale. Included in delivery are: 01x railing posts, second choice Material color: Ral 7001 Silver Gray Manufacturer: SSI Schäfer Total height: approx. 1.130mm Total width: approx. 32 mm Total depth: approx. 55 mm Base plate: 120 x 80 x 15 ( W x D x H) Diameter round tube opening: approx. 35 mm Distance of holes: 500 mm ( center hole ) Material thickness: approx. 3 mm Weight pcs.: approx. 3,64 Kg Notes: - The railing post is open from above. If desired, you can get matching plastic caps. - The heights of the round tube openings are: 575 mm and 1,075 mm ( Measured from lower edge base plate to lower edge round tube opening ) - suitable for round tubes with a diameter of 34-35 mm - For fastening we recommend 4 screws M8 (8.8) - Slip-through opening must not be larger than 900 mm. - If the railing posts are drilled t ...
used
We offer you a railing post from SSI Shepherd for sale. Included in delivery are: 01x railing posts, second choice Material color: Ral 7001 Silver Gray Manufacturer: SSI Schäfer Total height: approx. 1.030mm Profile: 55 x 30 x 2.0 mm (D x W x S) Base plate: 120 x 80 x 15 (W x D x H) Diameter round tube opening: approx. 35 mm Distance of holes: 315 mm ( middle center hole ) Weight pcs.: approx. 3,37 Kg Notes: - The railing post is open from above. If desired, you can get matching plastic caps. - The heights of the round tube openings are: 345, 660 and 975 mm ( Measured from lower edge base plate to lower edge round tube opening ) - suitable for round tubes with a diameter of 34-35 mm - For fastening we recommend 4 screws M8 (8.8) - Slip-through opening must not be larger than 900 mm. - If the railing posts are drilled through a beam ( CS, C or IPE ), then no count ...
used
Description Conversion kit high-speed cutter Wohlenberg from Monitor Tube chassis system 85/86/90 to LCD chassis The following steps are necessary for the conversion to LCD: 1. Disassemble the monitor chassis 2. Remove the picture tube and circuit board (ventilate the tube properly, dispose of) 3. Function keys, alpha keyboard is retained (if available) 4. New LCD chassis, loosen nuts and lift the frame 5. Insert chassis from behind, attach front bezel and screw it in place 6. AMP connector from the CPU unplug, eject contacts 7. Set the voltage on the potentiometer to 12 volts 8. Press in new pins after enclosed pin assignment 9. For System 86/90, pinch off the crimp contacts and insert them into the pin header 10.AMP connector System 85 / Plug in pin header on System 86 11.For System 86/90, tap the voltage on the switching power supply (snap terminals) 12.Settings of the LCD monitor are ...
new
New! Heavy duty support SFS D30, DIN EN 1065, 1,70-3,00m galvanized, new á 41,30€ net Loadable like a 30KN support at the introductory price of a 20 KN support of 41.30 € / piece net! Hot-dip galvanized, hot galvanized, 8mm head and foot plate, fully extended 29.3 KN handle on top. Stem bottom 34,80KN fully extended. Tube diameter outer tube 76mm, inner tube 63.5mm. Weight of one support 17,80KG/ piece. On request, the supports can be provided with your company logo from an order volume of 500 pieces! European Community product All prices excl. VAT and transport Sale reserved! If you have any questions, please call 0049 176 70044689, Mr. Becker Purchase and sale of scaffolding/formwork systems and construction machinery; Formwork restoration at fair conditions. Company SFS Meisterbetrieb Andreas Becker e. Kfm. Office/ warehouse address: Birkenst ...
used
Screw compressor system semi-thermal air conditioning compressor Compressor Chiller 2 x 30 Kw electric for air conditioning systems. 2x Screw compressor Manufacturer: RefComp Type: SRC-S-133 Ser.-No.: RE00093364 & RE00093366 400 V; 277/398 A; 50 Hz; IP54 rated power Leistg.: 30 kW Funding volume: 150 m3/h Pressure: 19-26.5 bar 3x Shell and tube condensers Manufacturer: WTK Type: CF270 CA2P Y.O.M.: 2009 272 kW (46.80 m3/h); 273 mm Tube Side: 10-11 bar; -10/+120 °C; 26.0 dm3; H2O Shell Side: 30-33 bar; -10/+120 °C; 85.9 dm3; gas with control box / control box with main switches, control & switching modules & pcd7. D232 terminal display. with piping and other various extensions, all mounted on a sturdy 4-edge dread tube frame. Total approx. 3450 x 1400 H 1900 mm Subject to changes and errors in the technical data, dates and prices as well as intermediate s ...
used
MACRI ITALIA PROVAR 6-45 U-D bending machine was manufactured in 2019 in Italy. The fully automatic mandrel bending machine is used in the process of machining tubes and profiles with a maximum diameter of 45 mm in 6 numerically controlled axes (X, Y, Z, B1, B2, A). Excellent process stability and workpiece quality, with the possibility of bending standard and variable (free) radiuses, are guaranteed thanks to the robust steel construction, the moving head with high-strength gears and the equipping of all machine axes with brushless servomotors. The MACRI PROVAR 6-45 U-D CNC tube bending machine is controlled using state-of-the-art MACRI software with the ability of importing files from 3D programmes and performing an anti-collision test with 3D simulation, programming of positioner force and automatic mandrel lubrication and many other useful functions. The total weight of the machi ...
used
tube diameter max.: 38 mm wall strength: 2 mm bar material dia. min.: 10 mm bending radius min.: 35 mm bending radius max.: 150 mm pull up length of tube: 4500 mm bending angle max.: 180 ° accuracy of bending angle: ± 0,2 ° total power requirement: 7,5 kW weight of the machine ca.: 1,2 t - with 8-pos. bending angle pre-selection - crawler gear control - positioning device by hand - tube twist device Following bending tools are with the machine: - ø 10 mm, radius 27,5 mm - ø 12 mm, radius 35 mm - ø 12 mm, radius 56 mm - ø 15 mm, radius 35 mm - ø 15 mm, radius 57,5 mm - ø 18 mm, radius 35 mm - ø 18 mm, radius 59 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
new
tube diameter: 2 x 3,91 mm ST tube diameter: 60 x 4,5 mm GAS revolutions per minute: 2,5 U/min radius: min. 2 x D mm bar material - diameter: 35,0 mm total power requirement: 1,5 kW weight: 130 kg Furnishing: - mandrelless tube bending machine - mechan. Angle adjustment via dial - Tool holder: hexagonal 40 mm + 50 mm - Bending angle: 0 ° to 180 ° (max. 210 ° angle of rotation) - Bending radius: R10 to R270 mm - integrated chassis Bending segments on request The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
used
We offer you here a used square tube for sale. The square tube consists of 2 C-profiles welded together. Included in delivery are: 01x square tube/ C-profile, used Material color: sendzimir galvanized Total length: approx. 2,750 mm Profile: approx. 45 x 45 mm Material thickness: approx. 1.2 mm Hole diameter: approx. 6 mm Distance center - center hole: approx. 2,730 mm Shipping costs on request
used
Güntner GVH 102B/2x2N air-cooled condenser Patented Güntner support tube design All fans in ISO F version Performance data in R404A Condensing Block: The refrigerant-carrying core tubes are relieved by the patented support tube construction. This results in increased protection against leakage. Copper tube ∅ 12 mm, 50 x 25 mm offset Aluminium slats, spacing 2.4 mm Distribution and manifold pipes as well as pipe connections in copper Permissible pressure: ps=28 bar Permissible temperature: ts=100°C Ventilators: Low-noise axial fans with maintenance-free motors with protection class IP54, three-phase 400/3/50, according to DIN 40050 Execution: Insulating material class F Permissible conveying temperature -30 to +55°C All three-phase fans are generally equipped with 2 speeds (∆-Y switching) as well as speed-adjustable by means of Güntner control devices ...
used
SHUZ TUNG CNC 50 BRM CNC tube and profile bending machine built in 2014 in Taiwan allows for fully automatic, serial production of complex spatial workpieces in 5 axes with simultaneous hole punching. Excellent precision and accuracy of bending are guaranteed by the reliable servo motors used in the machine, which are responsible for realising the main working movements, i.e. bending, rotation and material feed. The rest of the movements are driven by a central hydraulic system with electronic lubrication. The SHUZ TUNG CNC mandrel bending machine is operated via a control panel with an installed CNC controller with the option of saving an unlimited number of programmes. In addition, the automatic servo bending machine is equipped with several bending rolls, a high-quality mandrel and an actuator to support material feed. The 50 BRM automatic CNC mandrel bending machine weighs 3500 kg ...
used
Orbital welding system built on a transport trolley with tool drawer and bottle holder. With 2 cassette welding heads: 1 piece 76 S with interchangeable inserts for tube AD 13.5 / 17.2 / 21.3 / 42.4 / 48.3 / 60.3 / 76.1 mm and for tube AD 19.0 / 23.0 / 29.0 / 35.0 / 41.0 / 53.0 / 54.0 mm 1 piece 115 with interchangeable inserts for tube AD 85.0 / 114.3 mm From first ownership. It is not possible to specify the operating hours.
used
X - axis: 0 mm Y - axis: 0 mm Plasma Tube Cutting Machine is highly accurate and versatile. It can cut multiple profiles: pipe, flat bar and box section. The Multiple Profile Cutting Machine combines the cutting capability of three machines into one machine. Length:14.000 mm Width:3.500 mm Height:2.300 mm Minimum Tube diameter 60 mm Maximum tube diameter 1016 mm Maximum Workpiece weight 6 Ton Number controlled axis 6 Plasma cutting with power supply Max. wall thickness ca 60 mm
used
KÄRCHER ROBO 30 pipe boring machine for pipes, flat material and profiles With this machine, tubes, flat material or profiles can be cut very quickly and accurately in a single pass. can be drilled or milled at an angle or at an angle up to 50° in such a way that filling rods or filling tubes up to 1" can be drilled or milled can be plugged through. With the standard additional clamp for the jaw chuck, you can not only cut pipes, but also transport flat material or other profiles with the feed and at the desired angle up to over Make 50° single-sided holes or through holes. The clamping jaws in the self-centering vice have a recess at the top for flat material. We are unrivalled when it comes to converting to another material! The feed is positioned at 0.1 mm with the counter with absolute or chain gauge. With the ROBO 30, you don't need to set limit switches or cams for ...
used
Diesel tank system - company filling station - consisting of: 1 x Storage container, 10.000 liter capacity, used 1 x fuel pump, type Eco 75, brand new Description container: according to DIN 6616-D, above ground, double-walled, incl. test certificate. The container has two saddle feet, a manhole with dome cover, is used, emptied inside and professionally cleaned and is equipped with the following fittings: 1 filling tube with TW closure (filling cap) and immersion tube, 1 sounding tube with dipstick and dipstick closure, 1 vent pipe with vent hood, 1 brand-new limit value transmitter with type approval (AIII), 1 ladder and 1 spare sleeve for removal purposes, 1 optical leak detector with type approval and leakage fluid. The container is reprimed and painted on the outside. (RAL sound). L = approx. 5.30 m - D = 1.60 m - weight approx. 2.4 to. - ex wo ...
new
Heating oil tank - tank system - steel tank - diesel storage brand new - 100m³ capacity - according to EN 12285-2 (replacement for DIN 6616), above ground, double-walled, incl. test certificate. The container has two saddle feet, a manhole DN 600 with dome cover and is equipped with the following fittings: 1 filling tube with TW closure (filling cap) and immersion tube, 1 sounding tube with dipstick and dipstick closure, 1 vent pipe with vent hood, 1 brand-new limit value transmitter with type approval (AIII), 1 ladder and 1 spare sleeve for removal purposes, 1 optical leak detector with type approval and leakage fluid. The container is completely repainted - RAL 7011 iron grey. (Other RAL colours are also possible on request!) L = approx. 15.80 m - D = 2.90 m - weight approx. 19.0 to. - ex works, freely charged - (For transport reasons, dome covers an ...
new
Diesel tank - Heating oil tank - Tank system - Steel tank brand new - with 30,000 litres capacity - according to EN 12285-2 (replacement for DIN 6616), above ground, double-walled, incl. test certificate. The container has two saddle feet, a manhole DN 600 with dome cover and is equipped with the following fittings: 1 filling tube with TW closure (filling cap) and immersion tube, 1 sounding tube with dipstick and dipstick closure, 1 vent pipe with vent hood, 1 brand-new limit value transmitter with type approval (AIII), 1 ladder and 1 spare sleeve for removal purposes, 1 optical leak detector with type approval and leakage fluid. The container is completely repainted - RAL 9010 white. (Other RAL colours are also possible on request!) L = approx. 10.00 m - D = 2.00 m - weight approx. 5.9 to. - ex works, freely charged - General: You will receive a V ...
new
Heating oil Tank system Diesel tank and other hazardous substances. 50,000 litres capacity according to DIN 6616/D, above ground, double-walled incl. officially recognized test certificate. Tank environmental protection Wozniack . Specialist company according to § 19 Water Resources Act (WHG) offers as follows. Storage tank 50,000 litres double-walled new according to EN 12285-2 standard . The tank is new and will be equipped with the following fittings: 1 optical leak detector with type approval and leakage fluid(new) 1 filling tube with TW closure (filling cap) and dip tube, 1 sounding tube with dipstick and dipstick closure, 1 vent pipe with vent hood, 1 brand-new limit value transmitter with type approval (AIII)(new) 1 ladder Container dimensions Length 10.7000 mm Diameter 2500 mm Weight approx. 9.000 kg Of course, you can also design your tank s ...
new
Vertical mixing silo. Approximate capacity 56 m3, dimensions Ø3.590x8.370 mm of total height. Made of steel S-235 and built in sheet thickness 3 mm with perimeter rings of reinforcement UPN-80, support structure by means of 4 pillars HEA180 mm braced with HEA-120 profiles, inner thread of Ø300 mm, step 200 mm with shaft tube of 114.3x6.02 mm placed in tube-jacket of Ø 355x4,78 mm, registration on the side for visit and inspection and in the lower tube for emptying in case of jamming or breakdown, equipped with safety system, 4 inspection sights, two upper ventilation vents, maximum level indicator FILSA type MS-1, transmission by pulleys and belts with 22 kW motor at 1,000 rpm with safety protections, discharge pipe 200x200 mm connected to inner screw jacket of mixer with manual closure at the outlet mouth, Nozzle at the bottom of cone for complete emptying of machine, cat ladder with ...
new
brand new - with a capacity of 10,000 litres - according to EN 12285-2 (replacement for DIN 6616), above ground, double-walled, incl. test certificate. The tank has two saddle feet, a manhole with dome cover and is equipped with the following fittings: 1 filling tube with TW closure (filling cap) and immersion tube, 1 sounding tube with dipstick and dipstick lock, 1 vent pipe with vent hood, 1 brand-new limit sensor with type approval (AIII), 1 conductor and 1 spare sleeve for removal purposes, 1 optical leak detector with type approval and leakage liquid. The container is primed on the outside - on untreated sheets. L = approx. 5.30 m - D = 1.60 m - weight approx. 2.4 tons. - ex works, freely charged - We recommend: Sandblast the above container from the outside, prime and completely repaint - zinc yellow / RAL shade 1018 (see sample photo). (Other RA ...
new
brand new - with a capacity of 50,000 litres - according to EN 12285-2 (replacement for DIN 6616), above ground, double-walled, incl. test certificate. The tank has two saddle feet, a manhole DN 600 with dome cover and is equipped with the following fittings: 1 filling tube with TW closure (filling cap) and immersion tube, 1 sounding tube with dipstick and dipstick lock, 1 vent pipe with vent hood, 1 brand-new limit sensor with type approval (AIII), 1 conductor and 1 spare sleeve for removal purposes, 1 optical leak detector with type approval and leakage liquid. The container is primed on the outside - on untreated sheets. L = approx. 10.70 m - D = 2.50 m - weight approx. 9.5 tons. - ex works, freely charged - We recommend: Sandblast the above container from the outside, prime and completely repaint - white / RAL-9016 shade (sample photo). (Other RAL co ...
new
brand new fuel oil tank - diesel tank - storage tank with a capacity of 5,000 litres - according to EN 12285-2 (replacement for DIN 6616), above ground, double-walled, incl. test certificate. The tank has two saddle feet, a manhole with dome cover and is equipped with the following fittings: 1 filling tube with TW closure (filling cap) and immersion tube, 1 sounding tube with dipstick and dipstick lock, 1 vent pipe with vent hood, 1 brand-new limit sensor with type approval (AIII), 1 conductor and 1 spare sleeve for removal purposes, 1 optical leak detector with type approval and leakage liquid. The container is primed on the outside - on untreated sheets. L = approx. 2.80 m - D = 1.60 m - weight approx. 1.5 tons. - ex works, freely charged - We recommend: Sandblast the above container from the outside, prime and completely repaint - iron gray / RAL sh ...
new
Farm petrol station - company petrol station - diesel petrol station composed of: 1 x 16 qbm steel tank - brand new 1 x Nozzle type K-80 - brand new Description of storage containers: 16,000 litres capacity according to EN 12285-2 (replacement for DIN 6616), above ground, double-walled, incl. test certificate. The tank has two saddle feet, a manhole with dome cover and is equipped with the following fittings: 1 filling tube with TW closure (filling cap) and immersion tube, 1 sounding tube with dipstick and dipstick lock, 1 vent pipe with vent hood, 1 brand-new limit sensor with type approval (AIII), 1 conductor and 1 spare sleeve for removal purposes, 1 optical leak detector with type approval and leakage liquid. The container is primed on the outside - on untreated sheets. L = approx. 8.50 m - D = 1.60 m - weight approx. 3.5 tons. - ex works, fre ...
new
Diesel filling station - Home filling station - Gas station - Small filling station composed of: 1 x 20m³ storage container - brand new 1 x fuel dispenser type eco 75 - brand new Description steel tank: 20,000 litres capacity according to EN 12285-2 (replacement for DIN 6616), above ground, double-walled, incl. test certificate. The tank has two saddle feet, a manhole DN 600 with dome cover and is equipped with the following fittings: 1 filling tube with TW closure (filling cap) and immersion tube, 1 sounding tube with dipstick and dipstick lock, 1 vent pipe with vent hood, 1 brand-new limit sensor with type approval (AIII), 1 conductor and 1 spare sleeve for removal purposes, 1 optical leak detector with type approval and leakage liquid. The container is primed on the outside - on untreated sheets. L = approx. 6.90 m - D = 2.00 m - weight app ...
used
STROJARNE PIESOK XZMP 3150/6.3C 3-roll plate rolling machine built in Czechoslovakia in 1983 is designed for pre-bending and rolling sheet metal into cylindrical or conical covers and segments. The machine is distinguished by a fully welded structure with increased rigidity and three high-quality 300 mm diameter rollers with longitudinal grooves for easy alignment of the sheet. The bottom rollers, driven by a high-performance motor with two stages of rotation, allow for vertical repositioning during pre-bending and coiling, and also allow for an offset to an inclined position when the claw couplings are opened. As a result, each of the four lower roll bearings can be freely adjusted in the pitch range. The XZMP plate rolling machine has a control panel with a function to monitor the position of the lower rollers directly on the numerical indicators. The total weight of the STROJARNE ...
used
Antifreeze thermostat, thermostat JOHNSON CONTROLS 270XT-95008 Temperature range: -10 - 12.5 ° C Length capillary tube sensor: 6.0 m diameter capillary tube sensor: Ø 3.2 mm Switching capacity: 230 V AC, 15(8) A New ! Dimensions: 115 x 100 x 50 mm ( without capillary tube probe ) Dimensions ( packaging ): 230 x 130 x 65 mm
used
Bimetallic thermometer, thermometer, horizontal, with protective tube, 2 pieces RÖDER 0 to 60 °C Pitch: 1 degree Diameter: Ø 160 mm Flange diameter: Ø 14 mm Sensor: Ø 9 mm, Length: 55 mm Protection tube: Ø 11 mm, Length: 90 mm Screw-in thread: 1/2 inch material protection tube: brass new ! Dimensions ( single thermometer ): 160 x 160 x 130 mm
used
Documents drawings_information_parr_5410.pdf equilabo_offer_details.pdf Technical details The distinguishing feature of a fluidised bed reactor is that the bed of solid particles or catalyst is supported by a rising gas stream. This reactor allows the catalyst to be easily loaded and removed. This is advantageous when the solids bed has to be removed and replaced frequently. High conversion at high throughput is possible with this style of reactor. These reactors inherently have excellent heat transfer and mixing characteristics. GAS FEED: Two reactant gas feed lines, each with normally-closed automated pneumatic shut-off valve, filter, bypass valve, and reverse-flow check valve. One gas feed line has a mass flow controller sized for up to 0.5-25 SLPM of nitrogen with up to 2 bar delivery pressure. The other gas feed line has a mass flow controller rated for up to 50 ...
used
Specifications: Production line for EPE foam sheets EPE foam tube (optional; ask for the cost) Working hours 1200h, Like new, Include two changeable line for tube & sheet to one extruder L/D54, Include all auxiliaries (special pumps, spare parts, pipes e.t.c), To run immediately, Capacity 80 kg foam per hour Production: 500.000 m2 foam sheet per 20 days & 500.000 m foam tube 28 mm per 20 days Full equipment & complete without any other needs or auxiliaries Other Details: Guarantee: Without guarantee Current condition: Dismantled. Cant be seen in running condition Availability: Immediate Voltage: 90 Kw
used
Dural Cnc-60 5 axis tube bending machine Machine never used before Max. Tube Diameter: Ø60 mm x 3 mm Max. Center Line Radius : 220 Max. Bending Angle: 190 Max. Tube Length: 2500 Max. Feeding Length With Mandrel (mm): 3700 Bending Speed (°/sec): 80 Feeding Speed (mm/sec): 1~800 Turning Speed (°/sec): 150 Max. Pressure: 160 Total Power (3 Axis) : 17.25 Kw Total Power (4 Axis) : 18 Kw Total Power (5 Axis): 24 Kw
used
Scheugenpflug dosing system with DOS P016 feeder Dosing cell Multifunctional and modular Module for integration into automated production Sensors and light barriers for component and position detection protect against damage and ensure precise machining processes. For medium to large quantities, dosing cells are the ideal solution for most applications. High-performance bonding and potting processes make it possible to protect sensitive components from mechanical, chemical and corrosive influences. They also increase their service life. With the right dosing systems, high repeatability can be achieved today and thus a large number of different bonding, dosing and potting tasks can be reliably realized. Scheugenpflug DOS P016 Piston Feeder The Dos P016 piston dosing system is a high-precision volumetric dosing system designed to process 1K and 2K materials and cov ...
used
General SKU212T520 LocationBarneveld MakeBuss-SMS Mach.No.0012 Pressure Working pressure3.2 Bar Vacuum possiblecheck Working pressure vapour evaporator10.5 Bar Main Features Surface4.3 m2 Specified Features - Falling film evaporator Falling film evaporatorcheck Condenser:check Heating surface4,3m² Tube capacity100 Ltr. Number of tubes:13 Tube diameter44,5 mm Tube length2500 mm Shell capacity200 Ltr. Max. temperature-10/200 °C MaterialStainless steel 1.4539 (904L), Stainless steel 1.4571 (316Ti) Information Year of construction1994Falling film evaporatorsBuss-SMSColumns > Falling film evaporatorsBrand > Buss-SMS What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneve ...