tube mill used for sale

Table clamping area: 350 x 700 mm x-path: 500 mm y-way: 320 mm z-way: 400 mm Spindle holder: SK 40 Spindle speeds: 30 - 2500 rpm Operating voltage: 380 V Total power requirement: 2.2 kW Space requirement: 1500 x 1500 x 1800 mm Weight: approx. 1700 kg

Used sand miill Vollrath type VMSM 2/15 A. Two chambers 15 L volume each. Motor 24 kW, weight 1050 kg.

Control Other Brother C00 Speed [rpm] 10000 Travel X/Y/Z [mm] 700/400/300 Tool pick-up BBT 30 Main spindle: Technology Direct Drive Speed 10,000 rpm Power (max.) 26.2 kW Torque (max.) 92 Nm Tool holder BBT 30 Work table: Clamping area 800 x 400 mm Table load (max.) 250 kg General: Tool Magazine 21 Stations Rapid traverse in X/Y/Z 50/50/56 m/min Equipment/accessories: Chip Management Chip Conveyor Coolant Management Minimum Quantity Lubrication (IKZ), Fabr. Lubrix V5 4th axle Lehmann EA-510 with counter bearing Workpiece Clamping Hydraulic, 80-210 bar Support Control Pneumatic Automation Preparation I Automatic Work Area Door (Electric) Automation Preparation II Robot Interface Oil Mist Extraction Mechanical Separator, Fabr. Sara UC1 SD Stand riser 150 mm Setup operation Electronic handwheel Further equipment transformer

Used cryogenic mill model PCJ-500. Machine for grinding the product cooled with liquid nitrogen, made of 304 stainless steel, 16 mm thick, externally dimensioned: - length: 6844 mm - width: 2132 mm - height: 3588 mm. Focused on grinding the product based on liquid nitrogen, which allows achieving a temperature of -196 ° C. Liquid nitrogen does not come into contact with the product, it is the source of this low temperature. The cryogenic mill requires a nominal power consumption of 40.45 kW, at 380V, 50Hz.

Complete production line for bevel gears, consisting of 6 bevel gear milling machines Klingelnberg BF 201 including orders for contract work for sale Technical data Diameter: 240 mm Module: 10 mm Tooth width: 60 mm Dimensions: 2.3 x 2 x 1.7 m Machine weight: approx. 6,700 kg Information and data are non-binding, subject to prior sale Special features: Complete production line consisting of 6 machines with the following accessories: - Bevel gear machine - 1x interchangeable gear set - 1x test block - Mounts (proportionate) - Knife set (proportionate) - Documentation (1xOriginal / data set) Furthermore, contract gear orders could follow, catalogue goods and special bevel gear sets according to customer specifications, complete volume approx. 8,000 components / year. Asking price of the seller 18.000.- VB / per machine

Drives: 45 KW + 15 KW Weight: 2100 kg Dimensions: L 3.50 m x W 1.36 m x H 1.52 m;

Matsuura MC600VF Vertical Machining Centre in great working condition ready to use. COOLING TROUGH SPINDLE YEAR: 1997 with Yasnaz i80M Control, Table size 870 x 400mm, 20 Position ATC, BT40 Taper, Spindle Chiller, Coolant Tank, X = 600 Y = 410 Z = 470mm, Spindle Speeds 30 – 8000rpm. S/No. 970112285 including Large Qty of BT40 Tooling (33 TOOLS, Universal 3D Tester. Country of Origin: Japan. INCLUDED AS WELL BACK UP PARAMETERS.

KIMLA BPF 2030 CNC router was built in 2011 in Poland by POLCOM Przemysław Kimla. The machine was regularly maintained throughout its service life. In 2021, the ISEL 10 bearings along with the lead screw in the Z axis were replaced. KIMLA BPF 2030 is an excellent choice for both small and medium-sized companies with a diverse production profile. The machine enables precise machining of a wide range of materials, i.e. light metals, plastics and wood. After fitting a special cutting head, it is also possible to cut parts made of rubber and cardboard. All machining processes are performed on a large work table with an ergonomic design. The spindle, driven by a high-powered motor, rotates at a maximum speed of 24000 rpm and moves in three X,Y,Z axes with feeds of 2000 mm, 3000 mm and 500 mm respectively. Tools taken from a 10-position magazine are in turn continuously measured and calibr ...

Model MC-800VF WITH 4 TH AND 5 TH AXIS FIRST TIME IN USE FROM 1996 Brand MATSUURA Type Vertical Machining Centers Control CNC (Yasnac i80 CNC control) Table 1200mm x 400mm Power 15 hp RPM 12000 rpm ATC 30 Taper BT40 Axis 3+2 Weight APROX 7000 KG TRAVELS: X = 800mm, Y = 440mm, Z = 485mm mfg MATSUURA mpn MC-800VF Matsuura MC-800VF WITH 4 TH 5 TH AXIS MACHINE WAS WORKING IN ROLLS ROYCE FROM A NEW AND IS GREAT MANTAINED HAS NEW BATTERIES, BACKUP MADE.

oven 550 industrial 2x2x6m temperature range 100 - 550C Wärmebehandlungsöfen Wärmeofen Wärmeprozessöfen Warmhalteofen Warmluftofen Herdwagenofen Rollenherdofen Kammerofen Drehtellerofen Wagenherdofen & Tunnelofen Poreba Gurutzpe Tacchi Geminis Tos Amutio cazeneuve Skoda Morando Niles Colchester Heyligenstaedt Kramatorsk Mondiale Safop Cazeneuve Alzmetall mas stankoimport csepel carlton kolb soraluce bergonzi flott Erfurt Weingarten smeral schuler ebu mueller zts kosice wlochy minster Stanko stankoimport glaser huta zygmunt aft donaldson eumuko Elblag Engel Demag Arburg Krauss Maffei Battenfeld Manesty Mazak Voronezh Trumpf Amada Cincinnati Netstal Rose Forgrove Illig Foremost Nissei Sandretto Fette Mazak Mori seiki Haas Okuma Gildemeister Doosan Daewoo traub hwacheon index Wema zeulenroda mueller Erfurt tox presso technik dunkes galdabini hare ponar zeulenrdoda eitel  ...

Corundum stone mill Manufacturer: Fryma Type: MK-270 R Built: 1981 N°: F815198/9 Pressure working space: 1 bar Pressure double jacket: 10 bar with control cabinet with temp gauge with outlet chute various spare parts LWH: 1100 x 850 x 1700 mm

Tech. Data and more info on request

oven 1150 inner chamber dimensions 1 x 1 x 2m t max 1150 Celsius PLC Öfen Verzinkungsofen Ve rgüteofen Anlassofen Industrieöfen Glühofen Ovens laboratory ovens industrial furnaces industrial furnace plants Industrial Furnaces high-temperature chamber furnaces hardening furnace anlageHärteöfen Annealing furnaces Conveyor belt Abg aswäscher Abkühlungsöfen Abwärmerückgewinnung Aluminiumgiessereimaschinen Anlassofen Brennöfen Dentalofen Durchlauföfen Emaillierofen Fusingöfen Generatives Fertigungsverfahren Anlaßöfen mit Luftumwälzung Anwärmöfen Aluminium – Glühöfen Abschreckbäder Beschickungsanlagen für sbguss Druckgußmasch inen Drehherdöfen Doppelkammeröfen Draht – Glühöfen Durchlauföfen Elev atoröfen Glühöfen für verschiedene Einsatzarten Gas Nitrieröfen Härteöfen Härtebäder Herdöfen Hubbalkenöfen Herwagenöfen Haubenöfen Indust ...

SCM TECH Z5 5200 CNC woodworking center was built in 2015 in Italy by SCM Group S.p.a. This extremely efficient machine is used for precision machining of wood and wood-based materials (chipboard, plywood, etc.). It enables a number of complex operations to be performed, such as vertical drilling, horizontal drilling, grooving with a saw blade along the X axis and standard milling. The machining process is performed in 5 axes by means of a work head located inside a movable machining station. It consists of a boring head with vertical/horizontal spindles and integrated blade and electro-spindle with automatic tool exchange system. The machining station moves over a work table with suction cups that ensure secure holding of the workpiece during machining. On the inner base of the work table, in turn, there is a device designed for easy shavings removal. Each axis is driven by high-powe ...

Used shredder / shredder from Moco type AZ 17E/1210. Shredder MOCO AZ 17E, shredder with slow and quiet toothed working shafts. Low vibration and minimal maintenance, compact Robust welded structure, low power consumption, Individually interchangeable cutting discs. Very good inlet behavior, even for large bodies. High degree of fineness. The material is stopped by an optional sieve inside the cutting chamber for repeated shredding until its dimensions are smaller than the sieve openings. The control of the AC gear motors is equipped with an automatic overload-dependent reverse adjustment. BANDWIDTH EXAMPLE 15 to 18 cubic meters of loose mixed waste per hour. DIMENSIONS • Cutting section 932x912mm • External dimensions 2440x1112x730mm • Weight 4600 kg. • Drive power 2×15 kW • Voltage 400V/50Hz Year of manufacture 2010.

Milling machine lid FP 4 NC Built c. 1992 with controlled C-axis 2 pieces of screw sticks Various tool holders Machine is in top condition and was last serviced on 20.08.2020 for approx. 3.000,- € (net). documents available. The machine is sold only because of space requirements. Location of the machine: 76661 Philippsburg

Counter holder, counter bearing, bearing block, pillow block, bearing for milling machine -Dovetail: 168 by 224 mm, 42 mm high -Bore: Ø 58 mm -Drawing: in the photos -Dimensions: 390/115/H230 mm -Weight: 21 kg

Tool holder, milling holder, milling tool, cutter head -Take: SK40 3 pieces -Sizes: see pictures -Price: complete -Dimension box: 320/110/H150 mm -Weight: 3.5 kg

Tool holder, milling holder, milling tool -Intake: SK50 5 pieces -Sizes: see pictures -Price: complete -Dimensions box: 400/300/H270 mm -Weight: 42.1 kg

Tool holder, milling holder, milling tool, cutter head, adapter -Mill holders: SK40 3 pieces, clamping sleeve O 54/16 mm -Sizes: see pictures -Price: complete -Dimensions: 240/180/H70 mm -Weight: 4.8 kg

Laboratory bead mill Manufacturer: VMA Getzmann GmbH Type: Dispermat SL-C50 N°: 0819203 Built: 2003 as good as new with ceramic grinding set with control panel additional pump with user manual and documentation LWH: 670 x 700 x 370

Counter holder, counter bearing, bearing block, pillow block, bearing for milling machine -Dovetail: 265 by 215 mm -Bore: Ø 56 mm -Number: 2x counter bearings available -Price: per piece -Dimensions: 260/160/H150 mm -Weight: 10.7 kg/piece

Tool holder, milling holder, milling tool, cutter head -Adapter: SK40 M20 2 pieces -Sizes: see pictures -Price: complete -Dimension box: 205/105/H140 mm -Weight: 3 kg

Colloid mill Manufacturer: Probst & Class Type: N100E N°: 90028 Power: 5.5 kW Engine manufacturer: Loher with operating instructions various spare parts (piping, taps, etc.) LWH: 1150 x 400 x 800 mm

Corundum stone mill Manufacturer: Fryma Type: MMR-O N°: 166 with funnel & outlet Power: 12 hp with various grinding discs LWH: 500 x 500 x 1250 mm

tool holder, milling holder, milling tool, adapter, Weldon -Manufacturer.Gewefa, spindle tool type SK50x49x300-M24 -Hole: SK50/ Ø 29 x 300 mm -Total dimensions: Ø 98 x 440 mm -Weight: 7.0 kg

Collet chuck, tool holder, tool holder, milling chuck, milling tool -Milling chuck: SK50 2 pieces -Tool holder: Ø 32/16 mm -Price/Sale: complete -Overall dimensions: 355/180/100 mm -Total weight: 10.4 kg

Counter holder, counter bearing, bearing block, pillow block, bearing for milling machine -Bore: Ø 56 mm -Guide slide: 180 mm movable -Hole spacing: 213/170 mm, Ø 18 mm -Dimensions: 285/250/H460 mm -Weight: 50 kg

Tool holder, milling holder, milling tool, adapter, clamping unit -Manufacturer: Walter, 41 pieces holder/clamping units SK50 -Various types: see photos, more pictures can be sent -Price/sale: complete -Total dimensions: 700/600/260 mm -Weight: 129 kg

Fixed bed milling machine Zayer 2000BF. Table: 2500x700mm. Longitudinal travel: 2000mm. Cross travel: 1000mm. Vertical travel: 1000mm. ISO50. Speeds: 18. (28-1800rpm). Power: 15cv. Weight: 13000Kgs. Equipped with DRO Fagor.

Correa F3UE universal milling machine. Table: 1400mmx340mm. Longitudinal travel: 1100mm. Cross travel: 320mm. Vertical travel: 500mm. ISO50. Hure head. Speeds: 18. (28-1400)

Tool holder, milling holder, milling tool, cutter head -Manufacturer: Wohlhaupter, tool holder 195 015 TO13815 -Take: SK40 -Mandrel: 69871 ANSI 40-SMA 22/63 -Dimension: Ø 64 x 160 mm -Weight: 1.3 kg

Tool holder, milling holder, milling tool, cutter head -Recording: SK40 5 pieces Sizes: see pictures Price: complete -Box dimensions: 270/270/H160 mm -Weight: 15.2 kg

Qty. 1 Second-hand complete 12-Hi reversing cold rolling mill incl. sand blast line Mfc.: Kobelco Type: 12-Hi reversing Built: 1986 Strip width: 900 – 1250 mm Thickness: Entry: 3.2 mm Exit: 0.4 mm Rolling speed: 120/300 m/min.

Kolloplex pin mill type 630 Z, Drive : 55 KW Weight : 1100 kg; --> Stifscheiben diameter housing and door side : 630 mm;

Radius milling cutters, end mills, end mills, milling cutters -Cutter: 8 cutting edges -Diameter: 47/65 mm -Socket: Ø 32 mm -Dimensions: Ø 65 x 130 mm -Weight: 1.9 kg

Collet holder, tool holder, tool holder, milling holder, milling tool -Manufacturer: Clarkson, 2 pieces collet holder -Type: Autolock -Adjustment: SK50 -Tension sleeves: Ø 25/16 mm -Cutter: Ø 44/11.5 -Price: complete -Dimension total. 175/285/100 mm -Total weight: 9.2 kg

Tool holder, milling holder, milling tool, collet holder, milling chuck -Manufacturer: Nikken, Multi-Lock Milling Chuck -Type: MCA50F-32HM-SL -Tensioning sleeve: Nikken KM32-16 -Dimensions: Ø 98 x 220 mm -Weight: 4.5 kg

Parcels of 7 machines 1x CNC 5 axis milling center, brand Okuma, type MU 400 VA, built in 2004, with various accessories and tool holders 1x CNC 5 axis milling center, brand DMG, type DMU 50/60, year of construction, 1996 with various accessories and tool holders 1x CNC 3 axis milling center, brand Okuma, type VR 40II, year of construction, 1995 with various accessories and tool holders 1x CNC 4 axis milling center, brand Okuma, type MC 40VA, built in 1991, with various accessories and tool holders 1x tool adjuster, Make EZSET Type 400 1 x Schumpfgerät, Brand Heimer, Type Power Clamp, Year of construction 2019

Three-roller Manufacturer: Joseph Vögele AG Type: PW 3103 Item #: 713345 Year of construction: 1965 LWH: 550 x 850 x 1200

Milling machine +6 mesh Mesh size 0.2/0.6/1.0/2.0/4.0/5.0mm Germany Wall Engine Updrive M1S-632-2 B3 Single-phase AC motor with start-up and operating capacitor, 0.25 kW, 2800 min-1, 230 V 1~, 50 Hz, IP 55, Iso F, S1, 40° C, Design B3 (foot 80 x 100 mm) Hpg28ilv Pick up from 14547 Beelitz or shipping with extra shipping costs for more info please send email or by Whatsapp 00491605664856

Tool holder, milling holder, milling tool, -Manufacturer: May, milling adapter: SK50 with fine adjustment -Type: FGK3/SK50/N M14-M30 -Dimensions: Ø 98 x 300 mm -Weight: 5.9 kg

Flush milling machine HolzHer UF 362 Year of construction 1975 L x W x H: 150 x 80 x 160 cm Weight approx. 440 kg The machine is in good condition, ready for operation, Changes, errors, intermediate sale reserved ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone 0041 62 966 18 32 fax 0041 62 966 21 12