128,008 used machines on RESALE, but how to find them? Machine Search
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 95 mm Shaft diameter: 30 mm Shaft revolutions: 7 U/min roll diameter: 132 mm Drive: 0,75 kW weight: 220 kg range L-W-H: 530x900x660 mm Equipment / Accessories: - Two driven rollers with grooved surface - Manual feed of the upper roller - working position horizontal and vertical (with tilting base) - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn different profiles are used e.g. Flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
round material: 40 mm tube diameter: 70x2 mm square material: 80x30x3 mm L-beam: 50 x 5 mm I - beam section - flat steel: 80 x 16 mm I-beam section - upend: 50 x 15 mm roll diameter: 157 mm Shaft diameter: 50 mm bending speed: 2,95 m/min total power requirement: 1,1 kW weight of the machine ca.: 500 kg dimensions of the machine ca.: 1000x950x1450 mm Domestic equipments: - Special steel shafts (42CrMo4) hardened and ground - a set of standard rollers - lower rollers up and down hydraulically deliverable - digital display for lower rollers - separate control panel - in one direction manually adjustable lateral straightening rollers - manual lubrication - horizontal and vertical operation - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW connected load: 400/50 V/Hz hydraulic pump: 1,1 kW : 80 kN range L-W-H: 900 x 600 x 1000 mm weight: 470 kg Equipment / Accessories: - Two driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 80 mm roll diameter: 260 mm : 7 U/min : 170 mm : 27 kN : 160 mm : 450 mm total power requirement: 3,7 kW dimensions: 980x1430x1600 mm weight: 1380 kg Accessories / equipment: - Three driven rollers with a smooth surface - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can bend different profiles are used e.g. Flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: R10-R260 : 210 ° bending speed: 2 U/min : 1 1/4 x 3,5 mm : einphasig - 230 V drive motor: 1,1 kW : < 70 dB weight of the machine ca.: 80 kg dimensions of the machine ca.: 410 x 1000 x 570 mm Accessories / equipment: Hard copper and aluminum: 54x2 mm Steel tube: 42x3 mm Stainless steel: 42x2.5 mm Solid material: 30 mm Number of programs: 30 each 9 bends Control: Soft-touch control panel in 8 different languages Mobile by driving device The controller allows easy programming of the automatic cycle The controller is equipped with a system diagnostics and has a great language selection. Patented fast tool change system A single bending speed The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Used aluminium tube filling machine made by the Italian company IMA Comadis model 720 A. The Comadis 720 A is an automatic tube filling machine, designed specifically for metal tubes with a maximum diameter of 35 mm. This linear automatic machine is equipped with a crimp-sealing head and a tube orientation system, ensuring precision and efficiency in the filling and sealing processes. The machine features a conical product hopper with a heating/cooling jacket, located at the top of the unit, which facilitates a smooth flow of material. The unit is enclosed in a transparent protective housing, which ensures safety whilst allowing operators to visually monitor the filling process. Access to the interior is provided by transparent doors with handles, facilitating maintenance and cleaning. The control panel is fitted with a range of buttons and a clearly marked red emergency stop button, ...
: 48x3,5 mm : 48x2,5 mm : 32 mm : 64x2 mm bending speed: 2 U/min : R10-R300 total power requirement: 1,5 kW weight of the machine ca.: 110 kg dimensions of the machine ca.: 410x1000x570 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bar material - diameter: Ø 35 mm I-beam section - flat steel: 60x10 mm L-beam: 50 mm tube diameter max.: Ø 60x2 mm square material: 45x45x3 mm roll diam. toproll: 162 mm roll diam. bottom roll: 152 mm Shaft diameter: 50/40 mm turning speeds: 3,3 m/min total power requirement: 1,5 + 0,75 kW weight: 450 kg range L-W-H: 1050x950x1450 mm Domestic equipments: - hydr. Delivery of the top roller - standard roller set - side straightening rollers - Upper roll holder: 50.0 mm - Under roller diameter: 40.0 mm - Control panel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW range L-W-H: 1100x850x1350 mm weight: 495 kg Equipment / Accessories: - Two driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - Footswitch - standard roller set The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
L-beam: 50x5 mm square material: 50x40x3 mm I - beam section - flat steel: 120x15 mm I-beam section - upend: 60x10 mm round material: Ø 35 mm tube diameter: Ø 70x2 mm roll diameter: 155 mm bending speed: 4,3 m/min bore: 50 mm total power requirement: 1,5 kW weight: 400 kg dimensions: 830x730x1350 mm Domestic equipments: - Extended special steel shafts - a set of hardened rollers - Bottom rollers are driven - lateral straightening rollers - Foot pedal - horizontal and vertical working - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
I-beam section - flat steel: 80x20 (d1200) mm I-beam section - upend: 80x25 (d2100) mm L-beam: 50x50x6 (d1000) mm bar material - diameter: 40 (d800) mm square material: 60x60x3 (d4000) mm rectangle: 80x30x3 (d6000) mm tube diameter max.: 70x2 (d1600) mm tool adaptor: 60 mm roll diameter: 177 mm bending speed: 6,4 m/min total power requirement: 4 kW machine weight ab.: 970 kg Overall size: 1400x950x1450 mm Domestic equipments: - hydr. roller drive - Planetary gearbox delivery of the 2 lower rollers - for extra small bending radii - hardened tool holder (42CrMo4) - Standard roller set, hardened - lateral straightening rollers - mobile control panel - 3 driven rollers - Digital display - Machine horizontal u. vertically usable - CE mark / Declaration of Conformity - Operating instructions in German The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 40 mm : 8,5 U/min : 120 mm roll diameter: 152 / 162 mm engine output: 1,1 kW range L-W-H: 900 x 600 x 1000 mm weight: 470 kg connected load: 400/50 V/Hz Equipment / Accessories: - Three driven rollers - Manual delivery of the upper roller - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. He can turn used different profiles The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
shaft diameter: 60 mm Shaft revolutions: 6 U/min roll diameter: 215 mm pressure hydraulic cylinder: 180 kN dimensions: 1125x870x1620 mm weight: 820 kg Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 50 mm : 8,5 U/min : 100 kN roll diameter: 162 mm Drive: 1,5 kW weight: 495 kg range L-W-H: 1100x850x1100 mm Equipment / Accessories: - Three driven rollers - Hydraulic delivery of the upper roller - Digital display with memory function - Working position horizontal and vertical - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 63x4,2 mm external diameter: min. Ø 5 mm bending radius min.: 10 mm bending radius max.: 270 mm Bending Angle: max. 210 ° bending device: gegen Uhrzeigersinn total power requirement: 0,75 kW weight of the machine ca.: 130 kg dimensions of the machine ca.: 740x470x1030 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 215 mm shaft diameter: 60 mm Shaft revolutions: 6 U/min : 100x2 mm : 80x15 mm pressure hydraulic cylinder: 180 kN total power requirement: 2,2 kW weight: 720 kg dimensions: 1200x900x1700 mm Accessories / Equipment: - Three driven rollers - Hydraulic delivery of the upper roller - Working position horizontal and vertical - Digital display with memory function - Bearings with tapered roller bearings - Use of replaceable slide rails on the guide carriage - The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
: 60x3 mm : 60x2,5 mm : 35 mm : 64x4 mm : R10-R300 bending speed: 2 U/min total power requirement: 1,5 kW weight of the machine ca.: 130 kg dimensions of the machine ca.: 595x363x900 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 76-86 mm Shaft diameter: 20 mm Shaft revolutions: 11 U/min Bending capacity round tube: 30 mm : 25x6 mm Angle iron: 20x20x4 mm Drive: 0,18 kW range L-W-H: 530x420x500 mm weight: 80 kg The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Indexing tube without man 40/54 tap MAN Part Number: 419.01.004
Siemens Tube OPTI 150/30/50 HC Tubular housing: OPTI 150/30/50 HC - 100, Model No. 4803404 Tube Model No. 4803388 Focal spot 0.6/1.0 Depth Aperture Model No. 8375040 • Before taking over, all devices or systems have been tested on site for their functionality. • The tube is located in our warehouse in Freiberg / Germany. • You buy the tube in "IST" condition from the warehouse Freiberg (EXW), Saxony, Germany, and prepayment. • The sale is made as "Used", EXW Freiberg, Saxony, Germany, to resellers or dealers despite being fully functional without warranty. • The installation, commissioning and configuration of the system component must be carried out by the manufacturer or by a specialist or technician authorized by the manufacturer! • We are dealers of used medical devices. We do not repair or refurbish any of the items we sell. All items are used and sold as ...
I-beam section - upend: 100 x 20 (d 2100) mm tube diameter max.: 100 x 3 (d 3000) mm L-beam: 80 x 80 x 8 (d 2000) mm square material: 50 x 25 x 2 (d 600) mm bar material - diameter: 60,0 (d 1000) mm I-beam section - flat steel: 120 x 30 (d 600) max. 140 mm tool taper: 80,0 turning speeds: 4,2 U/min weight: 1600 kg dimensions: 1240 x 1375 x 1540 mm Domestic equipments: - Welded steel structure (St-52) - Rollers are driven by 3 separate hydraulic motors - Stepless speed - Special steel gears - Shafts are made of special steel, hardened and ground - Manual lubrication - Guide rollers are hydraulically adjustable - Lower rollers are hydraulically movable up and down - Infinitely adjustable speed of the lower rollers, move after below and above - Digital display for lower rollers - Separate and movable control panel - Horizontal and vertical operation - Production quality certified according ...
Inv. Num. : 5725 Type: A 89 TNCB Producer: CSM Created: 2014 Parameters: Maximum bending angle: 180 pcs Total power requirement: 15 kW The largest profile: 60x60x6 mm bending radius in the middle of the tube: 350 mm bending radius in the middle of the profile: 300 mm Machine height: 1200 mm Machine length: 4700 mm Machine width: 1200 mm Machine weight: 2500 kg
Unbek. Type, YOC ca. 1990, Revision 2002 Specifications: - Bending capacity at 45 kg / mm² up to approx. Ø 25 x 3 mm - Bending angle left + right selectable - Hydr. Double-sided bending function - Hydr. Delivery ° - Drive 400 V / 11 kW - Space requirement approx. W 1750 x H 2200 x D 2300 mm - Weight approx. 1600 kg - with - bending angle adjustment - Hydr. Voltage - Bending tools
CRIPPA CNC YEAR 2007 LOW WORKING HOURS INCLUDED TOOLINGS AND EQUIPMENT WE ORGANIZE FOR CLIENT AS WELL TRANSPORT
roll diameter: 350 mm : 110 mm bending speed: 1-5 m/min Bending capacity: 157 Wcm³ total power requirement: 7,5 kW weight of the machine ca.: 2950 kg Domestic equipments: - Direct drive of all three shafts - Single delivery of the side rollers - Horizontally and vertically usable - Hydraulically movable side rectifier (via control panel) - 2 digital displays for the feed rollers - Hardened rollers - Mobile control panel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Stock# UG6359 Little used automatic tube filling machine by Pablo (PL) model TB-250. Machine can work on filling plastic tubes (PE/PP). Dose range from 5 - 250 ml. Machine can run on tubes with diameters: 19, 25, 30, 35, 40, 50 mm. Height of tubes in range from 10 up to 210 mm. Working output depends on product and size of tube. For tubes with diameter 25-30 mm - in range from 3000 - 5000 pcs/h. Power consumption 7 kW, 3/400 V, 50/60 hz. Compressed air 6 bar. Cooling water connection dia 10 mm, outlet diameter 8 mm. Machine new 2020. Shipping dims: 1991 mm x 1441 mm x h 2300 mm/2600 mm (with pole) x weight 800 kg.
Key data: 60 mm, 2 mm
Bending capacity: Ø60 x 2 mm Bending angle: 0 - 180° Turret: 12-way adjustment Mandrel length: 4500 mm Bending tools: - Ø 22 mm - Ø 25 mm - Ø 48 mm Equipped with: - 3 thorns - Mandrel retraction device - Foot pedal - Bending speed adjustment Country of origin: the Netherlands Motor power: 7.5 kW Machine LxWxH: 5350 x 1100 x 1100 mm Machine weight: 2300 kg
Specifications Ø tubes / radius in mm: Ø 22 / 67 Ø tubes / radius in mm: Ø 10 / 36
used
Max tube diameter 76 mm Max thickness 3 mm Max bending degree 180 Bending radius max 260 mm
Unused ultrasonic sealer for plastic tubes. Power supply (V/Hz) 230/50 Operating frequency (kHz) 20 Sealing width (mm) 80 Power (W) 1500 Size of work surface (mm) 300 x 325 Dimensions of device (mm) 1100 x 650 x 530 Weight of device (kg) 75 Horizontal ultrasonic sealling machine for tubes of thermoplastics (PP, PC, PU, PA, PBT, PES, PVC, PM, etc.) with adjustable: welding time, sonotrode descent speed, welding pressure, welding depth, number (count) of welded tubes. The heat needed for ultrasonic welding is obtained by vibration of material particles.
Autom. tube filling machine for metal tubes. Machine incl. the following accessories: - heatable product container with level conroller - stirrer - coding device etc. Furthermore 4 pcs. format parts for tube Ø: approx. 13,5, 19, 25 and 30 mm.
Inv. Num. : 5648 Type: XOTM 60 Producer: UNIT Created: 2004 Parameters: Minimum tube diameter: 20 mm Maximum tube diameter: 60 mm Machine length: 4900 mm Machine weight: 130 kg
Used automatic tubing machine for aluminum and plastic tubes. Producer Sigma. Model PK1. Technical parameters Efficiency: up to 1,700 pieces/hour depending on the dose capacity and product viscosity Power source: 3+PE+N, 380V/50Hz Input: 4kVA Working pressure: 6 atm Heated air: 2-4atm (required) Air consumption: 2001/min Max. current: 14A Fillable doses: up to 100 ml, (Filling pump 100m1) Tube type: Plastic, metal Recommended main voltage cables: CMSM 5Cx2.5 Recommended main voltage protection: 3-pos. protection 25A char. "B" Electrical coverage of the switchboard: IP 54 Control box coverage: IP 54 Control unit: Simatic S7-200 CPU 226
CNC – controlled profile and tube bending machine for demanding and precise bending work with hollow sections and tubes. With our machines, aluminium – steel / stainless steel – various plastics such as PVC window profiles (depending on the application) can be bent with repeatable accuracy, regardless of the material. Depending on the equipment, our machines can also be used for three-dimensional bending work. Our REPANDUS models can work both horizontally and vertically. The models of the REPANDUS series work with a fixed upper roller and two movable lower rollers – this means that the straight end piece is relatively short compared to machine concepts with fixed lower rollers. The machine body is made of vibration-absorbing cast steel Shaft diameter of upper and lower rollers Ø 70 mm Shafts made of special steel – hardened and ground Bending force 190 kN Maximu ...
Stepped end tuber type 951, Gartemann + Hollmann, Year 1980, 4 plies, 2 colours, photo cell, Tube width 30-65 cm, Tube length 50-121 cm, Machine mechanically and electrically mounted, we also have a 4 colour tail end printer suitable for that machine
From business liquidation: Grit GX 75 H Radius Grinder Year of construction 2016 Dpbnjr 380 volts 2KW power with 31.5--40--46mm inserts mobile
Autom. tube filling machine for metal tubes. Machine incl. the following accessories: heatable product container, stirrer, coding device etc. Furthermore 4 pcs. format parts for tube Ø: approx. 13,5, 28, 30 and 35 mm. PLC TELEMECANIQUE.
maximum number of results exceeded
please refine your search
50 € 
