tube bending used for sale

OFFER PLATE ROLL 2000x6 mm SERGI 3ROLL INITIAL PINCH ASYMMETRIC 2050 X6 MM Rolls length 2050 mm -Top roll 170 mm -lower/Side rolls 150 mm -Power electric 5,5 Hp Capacity -plate width 2000 mm -plate thickness 6 mm with prepinch Configuration on the machine -Rollers surface hardened high strength -Central rolls driven electric rotation on gearunit -side roll electric run with prepinch Pinch roll position with handwheel Front open manual drop-end -Readout gauge of side bending roll -Foot-pedal electric rollers rotation back/forth -Joystick electric control of side roll -Safety installations with emergency stop. -Machine in good conditions

I am selling this machine. It can be tested when connected. The machine is located in the Czech Republic. Very good condition. Price includes dismantling and loading. Rated deformation force 400 t Working area of table 3100 x 6000 mm Max. ram stroke 1000 mm Clearance between columns 3100 mm Output of main motor 15 kW Height of the machine 4170 mm Widht of the machine 4150 mm Lenght of the machine 6000 mm Weight of the machine 44190 kg

Tube diameter: 25mm, wall thickness: 2mm, bending angle: 190°, feed length: 2000mm, weight: 2t, left-bending. Accessories: CNC IsoBend 2.0. Without mandrel bending device, monitor glass has impact damage but is still functional. An on-site inspection is possible.

Lisse 1250 x 8 mm Corrugated

gebr. CNC press brake Darley, type EHP 200, built in 1989 Press force: 2000kN Working width: 5200mm Power: 15kW Oil capacity: 160l Weight: approx. 20,000kg Tools & Accessories Included

Safety control for Trumpf. Suitable for V50 to V200 without Bendguart.

DM02 control module to Trumpf. Suitable for Trumpf built between 1998 and 2004

Trumpf Motherboard Control Board DELEM DA 65/69 SNA 4891 Control Motherboard Board DA 65/69 Trumpf bending machine built 2001-2004 including flat screen and front control panel

DM05 control module for Trumpf Suitable for Trumpf built between 1998 and 2004

DM01 control module for Trumpf Suitable for Trumpf built between 1998 and 2004

TBF controller card Trumpf bending machine suitable for Trumpf bending machine year 1998-2004

Inv. Num. : 8711 Type: MG 2000 x 25/20 Producer: Maqfort Created: 1998, GO 2016 Parameters: Working length rollers: 2000 mm Max. sheet thickness: 25 mm

Bending length / working length 2,500 mm Press force / bending force 1,500 kN (≈ 1500 kN) Max. sheet thickness (steel) approx. 2.0 mm Max. sheet thickness (aluminium) approx. 3.0 mm Max. sheet thickness (stainless steel / higher tensile strength) approx. 1.25 mm Max. bending height approx. 300 mm (depending on model) Power / Capacity (Electrical) 24 kW Machine dimensions: 4,050 × 1,600 × 2,400 mm Weight ~ 13,000 kg

A mandrel tube bending machine Sommer is available. Tube diameter range: 15mm-65mm, tube feed length: 3000mm, max. bending radius: 150mm, chuck: 200mm, tube clamping: hydraulic. Including accessories. Documentation available. An on-site inspection is possible.

We would have all these machines as a package for sale. 1x Press brake 160to 3m 1x Press brake 60to 2m 1x KRC 150 robot 1x welding robot cell with Kuka robot and Fronius TPS4000 1x Micron

ONE Bending Testing Machine Load range up to 200kN Class 2 in the load range 40kN Class 1 in the load range 100kN Class 1 in the load range 200kN Indoor crane available for dismantling

working length: 2050 mm : 2.0 mm max. wire thickness: 3.0 mm Underfloor: 110 mm motor strength: 165 mm motor strength: 22 kW bending speed: 5.2 mm/min length: 3150 mm height: 1150 mm width: 850 mm Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Shaft bottom/top: 30mm/30mm, max. round tube length: 48mm, max. round tube diameter: 3mm, max. flat bar dimensions X/Y: 50mm/10mm, max. square tube dimensions X/Y/Z: 40mm/30mm/3mm, weight: approx. 200kg. Documentation available. An on-site inspection is possible.

Manufacturer: HAEUSLER Model: HPR 330 V+H Year of Manufacture: 2007 Approximately 10 pallets of tools for round bar processing are included, with diameters of 60.5, 137, 91, 168, 76, 51, 152, 129, etc. Condition : Machine currently not in use and therefore not fully assembled Technical Data: - Maximum bending moment (at 240 N/mm² yield strength): 200–330 cm³ - Number of bending rolls: 3 - Roll arrangement: asymmetric / symmetric - Roll diameter: 520 mm - Driven rolls: all 3 - Roll drive: hydraulic - Working speed: 0–7 m/min, stepless - Speed compensation between upper and lower rolls: automatic - Roll rotation reversal: electro-hydraulic - Adjustable bending rolls: 2 - Adjustment of bending rolls: hydraulic - Roll position display: digital, 0.1 mm accuracy - Roll bearings: roller bearings - Number of pressure roller systems: 2 - Adjustment of pressure roller systems: hydrauli ...

Laboratory Furnace for Bending Test 120 kW Kiln 900 °C Chamber Furnace 2 bending chambers Ceiling height adjustment Temperature range: max. approx. 900 C Additional heating Control cabinet PC, Fabr. HP, Intel Core 2 Duo Voltage: 400 volts Power: 120 kW Year of Make: 2015 Antechamber Width: 900 mm Height: 300 mm Depth: 580 mm Bending chamber Width: 520 mm Height: 115 mm Depth: 550 mm More items - new and used - can be found in our shop! International shipping costs on request!

A flat steel bending machine for the production of ZB frames is available. Pneumatic pressure: 8bar, hydraulic pressure: 100bar, weight: approx. 5000kg. An on-site inspection is possible.

Inv. Num. : 8806 Type: XZMP 3150/16 Producer: PIESOK Created: 1982 Parameters: Working length rollers: 3150 mm Max. sheet thickness: 16 mm Number of driven rollers: 3 pieces Weight: 40000 kg

4roll plate bending machine 2500 X 12 mm with central support hydraulic for large diameters and side arm plate support Capacity plate width 2500 mm Plate thickness 12 mm Prebend 10 mm Upper roll 265 mm Lower rolls 245 mm Surface useful on rolls 2550 mm Power supply 380/50 Electric motor 15 Kw on hydraulic unit Configuration Hardened rolls very high surface resistance Conical bending attachment Digital position readout of the rollers Safety and emergency installed per norms Hydraulic rolls power driven with planetary gear unit Hydraulic motion of rollers individual with dual initial pre-pinch Open front drop-end hydraulic to unload the closed shells Central support vertical hydraulic operated for large diameters Side arm operated hydraulic support Total weight of the machine 7500 Kg Total weight of the machine 7500 Kg machine layout 4200X15 ...

Key data: 1520 mm, 3 mm

Asymmetrical 3-roll round bending machine with 2 motors Lower roller crowned 110 mm diameter Upper roller (swing-out) crowned 90 mm diameter Rear roller (motorized adjustable with digital display) crowned 110 mm diameter Double footswitch Weight approx. 1200 kg

Key data: 2540 mm, 8 mm

Max. bending length: 2540 mm Max. sheet thickness: 8 mm steel Upper roller diameter: 200 mm Clockwise and counterclockwise rotation via footswitch Safety rope hoist Conical rounds possible Motorized rear roll infeed Lower roll feed via handwheel with position indicator Weight: approx. 4,500 kg

conische buiging met geharde rollen met gemotoriseerde backroll Number of rolls: 3x Roll capacity cold: 1550 x 6 mm Roll dia upside: 140 mm Power needed: 2,2 kW Length: 2700 mm Depth: 750 mm Hight: 1000 mm Weight: 1420 kg

Boven- en onderrol worden aangedreven (planetaire tandwielkast) Conische buiging Automatische gelijktijdige balancering Onderste rol excentrische balk Number of rolls: 4 rolls - 2 roll driven Roll capacity cold: 3100 x 32 mm Roll dia upside: 410 mm Dia under roll - side rolls: 370 - 300 mm Power needed: 25 HP Weight: 19 ton

An old folding machine Schröder is available. Working width: 2500mm, max. material thickness: 2.5mm, upper beam stroke: 80mm, adjustment: 160mm, speed: 120°/s, working height: 850mm, weight: approx. 3500kg. A visit on site is possible.

Bending direction: clockwise, steel tube diameter: 50mm, steel tube thickness: 3mm, stainless steel tube diameter: 50mm, stainless steel tube thickness: 2mm, max. section modulus: 5cm³, bending angle: 180°+10°, max. tube length: 2000mm, max. radius range: 150mm, bending height: 1050mm, bending head length: 850mm, min. bend spacing: 400mm, nominal pressure: 250bar, operating pressure: 200bar. Machine dimensions X/Y/Z: approx. 3200mm/1400mm/1300mm, weight: approx. 1500kg. Documentation available. An on-site inspection is possible.

Shaft Ø: 40 mm Bending Capacity: Flat bar upright at 500 mm Ø: 60 x 10 mm flat at 400 mm Ø: 100 x 15 mm square at 500 mm Ø: 35 mm L-iron leg outwards at 450 mm Ø: 50 x 50 x 6 mm L-iron leg inwards at 600 mm Ø: 50 x 50 x 6 mm T-iron T outwards/inwards at 600 mm Ø: 60 x 60 x 7/50 x 50 x 6 mm Round bar at 500 mm Ø: 35 mm Shaft speed: 7.5 rpm electr. Connection: 380 V, approx. 1.7 kW Space requirement: 910 x 640 x 1400 mm Weight: approx. 400 kg

Workforce: 300 kN/30 t Tool height: 200 mm Stroke length: 0 - 300 mm Bending capacity with prism tool MW 125/240: 200 x 16/200 x 24 mm Bending speed: 0 - 1.3 m/min Drive motor: 380 V, 5.5 kW Weight: 800 kg Footprint: 1250 x 820 x 1120 mm

: 300 kN stroke length max.: 235 mm : 200x24 mm bending capacity max. - round: 60x4,0 mm toolpiece height max.: 250 mm : 660x1250 mm work height max.: 900 mm return speed: 20 mm/sec working feed: 10 mm/sec total power requirement: 3 kW weight: 950 kg Domestic equipments: - semi-automatic NC control (99 programs with 16 steps each) - incl. bending bolt (without punch) - Incl. tool holder for dies - incl. foot pedal Equipment: - Stamp, smallest U = 145 mm 85 °    H = 250 mm, R = 5 mm - Quick change Monomatrize 85 °    H = 250 mm, V = 63 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Specifications: Pressure: 50 t Bending length: 2000 mm Equipment: - Backgauge - Emergency stop push button - Foot control

sheet width: 1070 mm plate thickness: 4 mm distance between columns: 1100 mm diameter of upper rolls: 110 mm total power requirement: 5,0 KW weight of the machine ca.: 1,2 t dimensions of the machine ca.: 2,0 x 0,9 x 1,1 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1070 mm plate thickness: 9.0 / 10,0 mm distance between columns: 1070 mm diameter of upper rolls: 190 mm pre-bending capacity: 9,0 mm connected load: 5,3 kW weight of the machine ca.: 2,4 t dimensions of the machine ca.: 2,7 x 0,92 x 1,2 mm - Electrically adjustable rear roller - Electrically adjustable lower roll (material clamping) - Digital readout for rear roller movement - Digital readout for lower roll movement (material clamping) - Hardened rolls - Conical rolling - Swiveling top roll - Brake motor - Emergency stop - Documentation - 400V The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Offer 25514 Specifications: - Max. working length 3060 mm - Column passage 2690 mm - Max. pressing force 1300 kN - Max. distance table / plunger 535 mm - Stand projection 410 mm - Plunger stroke 215 mm - Lifting speeds - Downward speed idle max. 200 mm/sec - Upward speed 135 mm/sec - Downward pressing speed 1 to. 11 mm/sec - Total drive power 18 kW - Pneumatic connection 6 bar - Space requirement approx. W 3800 x H 2700 x D 2400 mm - Weight approx. 11500 kg - with: - with 6 axis CNC control DELEM - Two-hand control panel with foot switch - crowning device - Controlled backgauge with height adjustment 5 - 860 mm - hydr. Upper + Lower Tool Clamping - Die table displacement pneumatically supported

Offer 25513 Specifications: - Max. working length 2050 mm - Column passage 1750 mm - Max. pressing force 850 kN - Distance table / plunger 535 mm - Stand projection 410 mm - Plunger stroke 365 mm - Lifting speeds - Rapid traverse downward speed 200 mm/sec - Upward speed 135 mm/sec - Downward pressing speed 1 - 11 mm/sec - Total drive power 13 kVA - Space requirement approx. W 2700 x H 2900 x D 2100 mm - Weight approx. 9100 kg - with: - with 5 axis CNC control DELEM , DA - Y1 + 2 ; X ; R ; Z - Two-hand control panel with foot switch - Controlled crowning device - Controlled backgauge with height adjustment 5 - 860 mm - hydr. Tool clamping - Die table displacement pneumatically supported

Offer 25515 Specifications: - Max. working length 2050 mm - Column passage 1750 mm - Max. pressing force 850 kN - Distance table / plunger 535 mm - Stand projection 410 mm - Plunger stroke 365 mm - Lifting speeds - Rapid traverse downward speed 200 mm/sec - Upward speed 135 mm/sec - Downward pressing speed 1 - 11 mm/sec - Total drive power 13 kVA - Space requirement approx. W 2700 x H 2900 x D 2100 mm - Weight approx. 9100 kg - with: - with CNC control DELEM , DA - Two-hand control panel with foot switch - Controlled crowning device - Back gauge with height adjustment 5 - 860 mm - hydr. Tool clamping - Die table displacement pneumatically supported - Sharpening tool + V-die

Hand-operated 3-roll sheet metal round bending machine with asymmetrical roller order Specifications: - Working width max. 1020 mm - Material thickness max. 1.5 mm - Roller diameter 64 mm - Upper roller turned into a crown, can be swung forward - Rear shaft with handwheel diagonally adjustable for conical rounding - Lower roller adjustment with control lever and eccentric - Front shaft parallel - Space requirement approx. W 1250 x H 950 x D 750 mm - Weight approx. 200 kg

A cassette set of bending tools for FASTI MAK

Diameter of bending rollers 550 mm Drive Type Hydraulic Main motor power30 kW

sheet width: - mm plate thickness: - mm distance between columns: - mm total power requirement: - kW weight of the machine ca.: - t dimensions of the machine ca.: - m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Equipment: 1 pliers feed right 4 Carriage Units Working Range: Wire thickness range: 0.5 - 2.0 mm Band width: up to 10.0 mm Length of move; up to 100 mm Output: up to 300 rpm

Equipment: 1 Carriage Feed Right 1 eccentric press 250 kN 4 normal carriage units 1 narrow carriage unit Working Range: Wire thickness range: up to 6.0 mm Strip width: up to 80 mm Feed length: up to 250 mm Power: 10 - 250 rpm

Equipment: 1 piece BIHLER noise protection cabin 1 piece pliers feed right 1 piece eccentric press 70 kN 4 Norma sled units 1 piece narrow sled unit Working Range: Wire thickness range: 0.5 - 3.5 mm Strap width: up to 32 mm Feed length: up to 170 mm Power: up to 250 rpm

TECHNICAL DETAILS Sheet width: 1500 mm Sheet thickness: 6 mm MACHINE DETAILS Hfebqxim Iohy Alijqob Machine weight: approx. 1950 kg

Stock number: 4017 PROFILE BENDING MACHINE Manufacturer: Roundo , Type: R4 Machines NO.: 1735, Year of manufacture: 1977 Specifications: Angle steel 90x9 mm Flat steel 200 x 30 mm Frame steel upright 100 x 18 mm Round steel 60 mm Load by steel 40 Kg/mm2 30 cm3 Upper roller 275 mm Ø Shaft dia. 105 mm Square steel 55 x 55 mm T-steel 90x10 mm Total power 5.5 kW Length: 1500 mm, Height: 1400 mm, Width: 1400 mm, Weight: 2500 kg

Press brake Manufacturer: AMADA PROMECAM Type: HFB 125/40 Year of Make: 1991 Control: DELEM DA 58 Press force max:. 1,250 kg Stroke max.: 180 mm Sheet thickness 8 mm Working width/passage: 3.7 m Number of phases: 3 Power consumption: 11 kw Voltage/Frequency: 380/50 Rated current: 24 Weight: 9,900 kg Availability: immediately Reference Number: L2131

A semi-automatic NC tube bending machine Tracto-Technik is available. Tube diameter: 48mm, max. tube length: 3000mm, max. material thickness: 4mm, max. bending angle: 180°, max. bending radius: 125mm, bending accuracy: +/-0.2°, bending speed: 20°/s. Machine dimensions X/Y/Z: approx. 3900mm/800mm/1250mm, weight: approx. 700kg, control system: Siemens Simatic. Documentation available. On-site inspection is possible.

Key data: 200 t

Horizontal Hydr. Straightening and bending press, 200 tons, hand and foot control, hydraulics. 18kw, with bending tools.