trumpf punching used for sale

Single column hydraulic press, straightening press, punching bracket ECKOLDPressen frame with hydraulic cylinder, mobile press, punching unitType RSD 1500 - 125Masch. No. 317 / 690 Year of construction approx. 1986Compressive force 150 ton. Projection 125 mmSlide stroke 35 mmTable size 280 x 210 mmPlunger area 125 mmInstallation height (plunger to table) max. 265 mmTable height above floor 403 mmHydraulic operating pressure max. 500 bar- without hydraulic unit- Lifter surface with 4 threads M16 and 20 mm guide groove, one centering hole in the middle 15

Amada punching machine EMK 3610NT incl. loading unit MP300 for sale. We would like to hand over the machine complete with tools and Wilson X-Sharp grinding machine.

Eccentric punching machine HAULICK + ROOS type RVD 125Double column - Eccentric pressMasch. No. 212560 Year of construction 1981Compressive force 125 ton. Table size 880 x 800 mmTable opening 470 x 140 mmStand width 900 mmStand width laterally 415 mmRam stroke 45 mmRam adjustment range 0-80 mmInstallation height in the picture 340 mmStroke rate 50 to 300 strokes/min. Engine power main drive 22 kWNe-connection 380 Volt, 50 Hz- Double connecting rod engine with 4-bearing eccentric shaft for off-center tappet pressure

Hydraulic punch, punching rack for the use of punching units JOKA type HP-SHydraulic hole punch, hydraulic press for punching bracketYear of construction approx. 1995Printing capacity 5 ton. Projection 155 mmStroke approx. 20 mmPunching unit width max. 54 mmPunching unit height max. 220 mmDie holder 48 mmMotor power 1.5 kWNeching connection 230 volts, 50 Hz- for the universal use of punching units JOKA SW 20 or SWD 20- Projection of the punching units can be larger, can be pushed through to the rear- Stroke release via

Key data: 75 t, 80 mm, 120 1/min

Pressure 75 t Stroke rate 120-600 / min Sheet width 10-300 mm Table size 1050 x 820 mm Pusher clamping surface 960x820 mm Distance table - UK plunger 380 mm Adjustable stroke - max. 80 mm Feed length 0-150 mm Total power requirement 20 kW Machine weight approx. 13 t Feed unit with max. belt speed 70 m/min Eccentric shaft with 4-fold bearings 2 connecting rods Central lubrication incl. magnetic belt conveyor - in use until 2020 -Operating instructions -Manual - Circuit diagram etc..

A cylinder roll punching machine Adolf Illig is available. Pass-through width: approx. 850mm, pass-through height: approx. 120mm, roll diameter: approx. 190mm, table dimensions X/Y/Z: 2x approx. 1200mm/1200mm, working height: approx. 800mm, machine dimensions X/Y/Z: approx. 2700mm/1350mm/1550mm, weight: approx. 900kg. An on-site inspection is possible.

pressure: 25 t no. of strokes: 1500 Hub/min sheet width: mm total power requirement: 20 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 25 t no. of strokes: 1500 Hub/min sheet width: mm total power requirement: 20 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

740 x 1,050 mm max. / 330 x 480 min. Size MABEG Scale Layer Flatbed die-cutter Punching force 1.8 MN / approx. 182 t HFS Hot Foil System Feeder stack 115 cm Display stack 85 cm Total meter approx. 12 million

Punching force 45 t. 2 pcs. available from stock (Video under power on request)

Width 34 cm Year of construction 2000 electric punching and binding machine Electric Punching - Manual Tying Split 3:1 Table model Delivery date: short-term Price on request. We supply and install worldwide.

Inv. Num. : 8689 Type: SBL-1050SE Producer: SABRE Created: 1994 Parameters: Maximum format size: 1050 x 750 mm Minimum format size: 400 x 370 mm Maximum workpiece thickness: 0.1-2 mm Impact pressure: 300 t Service ramp dimensions: 3282 x 1740 mm Length: 5573 mm Height: 2025 mm Width: 2111 mm

gebr. CNC punching press Finn-Power, type F6 SV, year 2005 Press force: 300kN Max. workpiece width: 4061mm Max. workpiece length: 1528mm Max. workpiece thickness: 8mm Max. workpiece weight: 200kg Fast feed X/Y: 80m/min/60m/min Tower head seats: 20 Tower head speed: 30rpm Travel speed: 100m/min Oil tank capacity: 330l Max. operating pressure: 300bar Dimensions X/Y/Z: approx. 5900mm, 6300mm, 2500mm Weight: approx. 13500kg Control: Siemens Sinumerik 840D Table of the machine has been extended. (Without machine housing)

Punching force: 300kN, max. operating pressure: 300bar, weight: 13500kg, operating hours: approx. 52300h. Documentation available. An on-site inspection is possible.

pressure: 75 t stroke: 8-80 mm no. of strokes: 80-200 Hub/min ram - range of adjustment: 70 mm table surface area: 900x600 mm ram surface: 900x470 mm hole in the table: 450x180 mm dist. between columns - front to rear: 500x350 mm dist. between pillars (front to rear): 788 mm total power requirement: 10 kW weight of the machine ca.: 10 t dimensions of the machine ca.: BxTxH 1600x1200x2800 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Reference ID PP-52393 Category Flatbed Die Cutter Manufacturer Heidelberg Model Promatrix 145CSB Year Built 2018 Color- Impression- Working Hours - Speed-- Max. size 1060 x 1450 mm Min. size 450 x 580 mm Condition Good Location Europe Availability December 2025

sheet width: 750 mm plate length: 1250 mm plate thickness: 4 mm table surface area: 1600 x 1050 mm no. of strokes: 180 Hub/min max. punching diameter: 105 mm punching pressure: 25 t total power requirement: 4,0 kW weight of the machine ca.: 1,8 t dimensions: 1,9 x 1,9 x 1,7 m Punching and nibbling machine - Digital readout for X and Y axis - Tool cabinet with tools The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

video control station The VCPevo / VCP Evolution (often written VCPevolution”) is a fully automatic register punching & bending system for printing plates (offset printing) built by NELA. VCP” stands for: Video‐recognition of register marks (V) + Controlling via CCD image processing (C) + Positioning by stepping motor control (P) — as one brochure puts it. The machine is used in the pre‐press / printing-plate automation sector: it aligns exposed printing plates, punches the register holes, bends the plates (to the correct angle) in one cycle. The VCPevolution line is described as the new generation” of the VCP series, aimed at high precision, high throughput, integration into automation / plate sorting lines. According to NELA’s product page for VCP, the machine is available in different models and can easily be integrated into any automation solution.” nela.de Fin ...

Impressions=0 m, Condition= Very Good , Availability= 2025-11-03, Bed size 105x 147 cm Pneumatic clutch full working condition Video available

Specifications: • 75 x 53 cm 6 mm Accessories: • PC workstation • DZDV PC TOUCHSCREEN PC 32" 9970460-20 incl. console • SLEEKING System HAK 100/Brother hot foil printer/finishing system Year of construction: 2024 Price: We ask for your binding offer Available from: immediately Terms of delivery: ex site – EXW Wiehl Payment Terms: Payment before pickup Accessories without guarantee. The following applies: "Object bought as seen". The prospective buyer must satisfy himself on site of the completeness of the property.

2005 Amada EM2510NT Excellent condition 45 stations, 4 indexing No loading system A lot of tools and spares Books

pressure: t plate thickness: 5 mm sheet width: 40 mm total power requirement: - kW weight of the machine ca.: - t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

IBERICA JRK 105 with Blanking year 2000 A DIE-Cutting press of size 75 x 105 cm (29 517 Hours) Including : Stripping and Blanking Station, NON-Stop Feeder, Control and Pull Lay System, Mini. Paper thickness 90 g/m2, Max. Cardboard thickness 1,5 mm, Max. corrugated 3 mm, Chases and Frames, 300 Tons Cutting Pressure, Speed 8 500 S/Hours. In good Condition, Immediately available

Dimensions (L/W/H): 0x0x0 mm Weight: 35 kg Total power requirement: 0 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 0x0x0 mm Weight: 100 kg Total power requirement: 0 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dimensions (L/W/H): 0x0x0 mm Dimensions (L/W/H): 0x0x0 mm Weight: 35 kg Weight: 35 kg Total power requirement: 0 kw Total power requirement: 0 kw The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Manufacturer: AMADA Model: AC-2510 NT Year of Manufacture: 2008 Technical data: Punching force: 200 kN Punching drive: Servo-electric drive Machine frame: Bridge frame Travel range (X x Y): 2500 x 1270 mm Positioning speed (X-axis): 80 m/min Positioning speed (Y-axis): 90 m/min Axis simular velocity: 100 m/min Control: AMNC-F Find more here - .ucymachines/ Contact us at - sales@ucymachines

A shoe cutting press from Deutsche Vereinigte Schuhmaschinen (DSGV-/USM Group) is available. Press force: 25t, table dimensions X/Y: 900mm/450mm. Machine dimensions X/Y/Z: approx. 1000mm/900mm/1550mm, weight: approx. 300kg. An on-site inspection is possible.

Impressions=0 m, Condition= Very Good , Availability= 2025-12-23, Bobst Speria 106 Sheet Counter: 200 million Maximum format: 740 × 1060 mm Minimum format: 350 x 400 mm Maximum Speed: 7700 sheets/hour Pressure: 260 tons Stripping station CUBE control Centreline system for quick job changes Quick lock stripping frame Micrometric adjustment 1mm thin plate system Electronic sheet travel control Double-action stripping OS pull side lay OOS push side lay Make-ready table - stripping Non-stop delivery

Equipment: 1 Carriage Feed Right 1 eccentric press 250 kN 4 normal carriage units 1 narrow carriage unit Working Range: Wire thickness range: up to 6.0 mm Strip width: up to 80 mm Feed length: up to 250 mm Power: 10 - 250 rpm

Equipment: 1 pliers feed right 4 Carriage Units Working Range: Wire thickness range: 0.5 - 2.0 mm Band width: up to 10.0 mm Length of move; up to 100 mm Output: up to 300 rpm

Equipment: 1 piece BIHLER noise protection cabin 1 piece pliers feed right 1 piece eccentric press 70 kN 4 Norma sled units 1 piece narrow sled unit Working Range: Wire thickness range: 0.5 - 3.5 mm Strap width: up to 32 mm Feed length: up to 170 mm Power: up to 250 rpm

Inv. Num. : 8884 Type: OMATIC 130 DTR Producer: OMES Generated: 2000 Parameters: Compressive force: 30 t Maximum length of sheet metal plate: 4000 mm Maximum blade width: 1500 mm Machine weight: 8700 kg Equipment: Accessories

max. sheet format 1040 x 740 mm, min. 400 x 350 mm, stripping station, centerline, non-stop feeder, non-stop deposit, drawing mark left, sliding mark right, gripper edge separation, raised 41cm, production hours: 25,000, Bobst-Cube control, micrometer adjustment, electric double sheet control, 1 upper die-cutting frame with quick-release fastener, 1 die-cutting plate 4mm, 1 upper stripping frame, 1 lower stripping frame, max. machine speed 7000 sheets/hour, max. punching force 250 tons, Processable materials: paper min. 80g/m², cardboard up to max. 2000g/m², corrugated cardboard up to 4mm. Overhauled, repainted

Mubea Hole Punch Model KL 750 Optima Year of manufacture 1990 fully functional Hebqowr Dk Rjxim Iqsfb Max. punching force 750 kn Triggering stroke via foot switch With very extensive tools, see photos

This AMADA Vipros 255 was manufactured in 2001. It is a used punching and bending machine, ideal for those looking to enhance their metal fabrication capabilities. Contact us for more information about this machine.

RABOLINI IMPERIA C WITH AUTOMATIC FEEDER -Automatic Die cutting machine with Rabolini hot foiling attachment -Year: 1990 -Electromagnetic clutch -Max Sheet Size : 800x1100 mms., Max die cutting size 750x1050 mms. -Control cabin for sheet speed control from 900 / 1600 Sh/hour -Honeycomb plate for hot stamping, 2 chases and frames for die cutting -Three programmable heating zones from control cabin -Rabolini Hot stamping foil unit with programmable pulling rolls -Max pressure power: 280 tons -All parts and accessories -Available in April

Hydr. 25 ton plate punching machine with sliding head Work area 1600 x 500 mm Weight approx. 1500 kg Height 210 cm

This TECHNOLOGY Tecnotransfer 1500x3000 was manufactured in 2007. A robust CNC punching machine, it offers precision and efficiency for your metalworking needs. If you are looking to get high-quality punching capabilities, consider the TECHNOLOGY Tecnotransfer 1500x3000 machine we have for sale. Contact us for more information.

Demonstration device Hand punch incl. 4-piece haulm divider and haulm plate DIMENSIONS Length 840 mm Width 585 mm Height 1120 mm Weight 42 kg

Heidelberg OHZ S, age 1956 540x720 mm (21x28") for die-cutting Available: at short term

This Finn-Power TRS 6 SUV was manufactured in 2003. A robust CNC punching and shearing machine, it features a punching force of 300kN and shearing force of 250kN. It includes a turret with 20 tool positions and optional a sheet metal storage capable of handling 40 pallets. Ideal for high-quality punching capabilities. Contact us for more information.

Cart beam punching machine / travelling head die cutting press 25 ton, 1600 x 500 mm, punching head 500 x 500 mm with 2-hand touch triggering, with light curtain approx. 1500 kg

This UZMA MAKINA PDM 30 was manufactured in 2012. It features an electronic PLC with a standalone control system, a maximum tube diameter of 90 mm, and a profile size up to 40 x 80 / 60 x 60 mm. The hydraulic motor power is 4 kW, with a total motor power of 5.5 kW. Consider the opportunity to buy this UZMA MAKINA PDM 30 CNC punching machine. Contact us for more information.

Plate punching machine 70x100 Brand: Grapho Metronic

This Finn-Power F6-25 5B was manufactured in 1997. A robust CNC punching machine with a machine weight of 14500 kg and a punching force of 300 kN. It operates at a maximum working pressure of 300 BAR. If you are looking to get high quality punching capabilities consider the Finn-Power F6-25 5B machine we have for sale. Contact us for more information.

new EcoCut V8 perforated sheet punch consisting of: - Eccentric punch with drive - Infinitely adjustable feed speed - Machine body: RAL 5003 / coarse structure / semi-gloss - Control cabinet: RAL 7035 / coarse structure / semi-gloss - Front panel: RAL 5003 / structure / semi-gloss - EcoOil Lubrication System for EcoCut Punching Machines - Integrated compressed air supply unit for EcoOil lubrication system - Machine table EcoCut for setting up automatic punching machine - Punching oil - standard 1 liter special cutting oil for optimal lubrication of all EcoCut tools - Round hole punching tool 7xd5 Sheet thickness steel :0.7 mm Sheet thickness aluminium :1,0 Sheet thickness front: 0.5 mm Colour: light grey/blue Total power requirement: 16 A Weight: 500 kg Dimensions: 910 x 1120 mm Projection: 280 mm Punching capacity 150 stroke/min Compressed air :2 - 5 bar Steples ...