126,706 used machines on RESALE, but how to find them? Machine Search
Used multi-layer paver Zenit 844 Built in 1993 inclusive: 1 piece concrete mixer 750 l Teka 1 piece concrete mixer 500 l approx. 12 pieces of used moulds approx. 100 production pallets Used concrete multilayer machine Manufacturer: Zenith Type: 844 Year: 1993 including: - 1 pcs 750 liter mixer Teka - 1 pcs 500 liter blender - about 12 moulds - about 100 pcs production boards
Unused, crimping range 15-63mm, maximum aperture 75mm, 53.5 mpa, force 500 T, 3000W
Unused, crimping range 15-63mm, maximum aperture 75mm, 53.5 mpa, force 500 T, 3000W
Specifications: Capacity 40 tons 2 strokes 57 + 86 H/min Projection 250 mm Plunger stroke 8 - 88 mm Plunger adjustment approx. 63 mm Table , WxD approx. 570 x 450 mm Max. installation height approx. 330 mm
Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw
Machine number: 35-173-98 Serial number: 2-0499 Compressive force: 4.5 kN Stroke: 60 mm incl. transport trolley
max. bar: 400 Serial number: 2121 Press force: 150 t Table dimensions: approx. 1500 x 560 mm Max. stroke: approx. 250 mm
Hydraulic Hose Press; Crimping range: 15-63mm, Max aperture: 75mm, Voltage: 380V, Wattage: 3000W, Pressure: 53.5 Mpa Packing size: 780x540x1350 Weight incl. packaging: 280 kg Unused.
Inner diameter: 220 mm Inner belt width: 200 mm Year of construction 02/90 Load capacity per reel is 150 kg, whereby the reel must be screwed to the ground. Weight approx. 450 kg Incl. wiring diagram
VORONEZH K8544 Hot Forging press YEAR : 1980 / 2008 OVERHAUL AND INSTALLED FORCE : 2500ton RAM STROKE : 350 mm RAM SIZE : 1120X1070 mm TABLE OVERALL SIZE : 1400X1200 mm NUMBER OF STROKES IN CONTINUOUS MODE : 60 NUMBER OF STROKES IN MANUAL MODE : 26 SHUT HEIGHT : 890 mm STROKE OF UPPER KNOCK OUT : 60 mm STOROKE OF LOWER KNOCK OUT : 70 mm MAIN MOTOR : 132KW (CHANGED TO HYUDAI HEAVY Y2012) PRESS OVERALL DIMENSION : 5380X4680X6400 mm HYDRAULIC BOLSTER NEW IN 2007 CONDITION : VERY GOOD WORKING CONDITIONS Trimming press available
Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw
Specifications Maximum pressure: 60 tons Press force: 156 t/m² Bale size: 1100 x 1100 x 700 mm Bale weight: 400 kg Power supply: 400V/ 13kW Year of construction: 2014 Dimensions of the tailgate: 2815 x 1085 x 2250 mm Machine weight: 7.5 t The machine is functional
Equipped with shrinkage of 6-45 mm; Manual pump; Shrink force 1000Kn; 7 Sets of molds; Completion indicator light; Maximum opening diameter without mold: 50mm; Maximum opening diameter with mold: 40mm; Hydraulic tank capacity: 1L; Hydraulic oil capacity: 0.5L; Unused
Length approx. 3.2 meters; 13 mm lip
Condition: unchecked Item is sold as is Weight may be ggbfs. Deviate. Machine must be dismantled by the buyer and transported out of the hall area. It cannot be guaranteed that a forklift is on site.
SINGLE POINT OPEN BACK INCLINABLE POWER PRESS Inv. No. 11.420PC Make IWK Model PEKRON 150Z Machine No. 1501 Capacity 150 tons Ram stroke 200 mm Ram adjustment 100 mm Shut height min/max 370 / 570 mm Strokes per minute 40 Knock out in ram 0 – 70 mm RPM 10 - 815 Throat 290 mm Power inclinable 30 degrees, 4kW Table 1000 x 630 mm Ram 760 x 410 mm Q 12 Volts 230 / 400 Cycles 50 Hz Including: Bolster plate 1.000 x 630 x 80 mm Bolster plate 1.000 x 630 x 90 mm Table opening, diameter 440 mm Updated electrics 2004 CE certified
Gluing Press / Press Rotor / Gluing Stars For the production of solid wood panels or similar Manufacturer: ACMA Levels: 4 Hydraulic Cylinders: 6 per level Hold-down: 2 frames per level Working area per level approx. 2900 x 1150 mm
SECOND HAND BENDING PRESS - plates dimensions mm. 3100X800 - opening mm. 800 - 8 cyl. diam. 80 mm.
Delivery date: 1961 Press force: 63 t Largest sheet thickness: 10 mm Stroke rate: 65 1/min Ram stroke: 8 - 100 mm Lifter adjustable: 63 mm Greatest distance between table and ram at max. stroke bottom, adjustment top, table bottom: 450 mm smallest distance between table and ram at max. stroke bottom, adjustment top, table top: 180 mm for further technical data see nameplates Table dimensions below: approx. 610 x 470 mm top table dimensions: approx. 310 x 260 mm
Machine number: 23620678 max. compressive force: 250 kN Largest stroke: 150 mm Drive power: 7.5 kW Operating voltage: 380 V Table dimensions: 570 x 380 mm
"Max. test pressure: 7 tons Max. distance from lower bearing: 2000 mm Max. distance from upper bearing: 600 mm Max. sample width: 250 mm Max. sample height: 200 mm" on pallet
Equipped with 1 set of tools, please note the control is defective
Specifications Maximum pressure: 65 tons Pressing force: 84 tons/m² Duct cross-section: 1000 x 750 mm Bale weight: do 550 kg Power supply: 400 V/ 45 kW Year of construction: 2011 Number of ties: 4 vertical Dimensions of the tailgate: 1400 x 920 mm Weight: approx. 13 tones Bale tying: automatic
Specifications Maximum pressure: 50 tons Press force: 7.14 kg/cm² Duct cross-section: 1000 x 700 mm Bale weight: do 500 kg Power supply: 400 V/ 30 kW Number of ties: 3 horizontal Dimensions of the tailgate: 1250 x 950 mm Weight: about 10 tons Bale tying: automatic Open hopper allows filling with the conveyor belt. Knife on the press plate and on the frame of the press to cut off the excess material. Automatic regulation of the light from the duct. Automatic binding with wire Choice of the length of the finished bale Press plate stably guided on the large rollers Large flaps of the press chamber for easy maintenance
Serial number: 055-007/12 Operating voltage: 220 V Frequency: 50 Hz Nominal current: 45 A Connection: 12.5 kW Control voltage: 60 W Press force: 25 Mp Operating pressure: 160 kp/cm³ Speed: 200 mm/s Sales: 450 mm/s Plunger stroke: 500 mm Projection: 360 mm Maximum distance between ram and table: 800 mm Table dimensions: 640 x 500 mm
"Lower counter bearing: 200mm Upper counter bearing: 600 mm Max. pressure: 35 kn"
Machine number: 0820592 max. load: 25 kN Throat: 90 mm Plunger strokes: 75 1/min Plunger adjustable: 30 mm Stroke adjustable: 2 - 40 mm Motor power: 0.25 kW Table dimensions: approx. 220 x 150 mm incl. The installed punching tool
Press screw REG-MAC for drying foils and fibres, and for compacting foam (e.g. polystyrene, EPS) Drive motor 55 kw
Equipped with 4 uprights and 8 beams and intermediate slats to place a wooden plate. Complete with side table with dimensions: 105x60x80cm and 4x zinc plate (antra) each with dimensions: 226x100cm
Equipped with shrinkage of 6-45 mm; Manual pump; Shrink force 1000Kn; 7 Sets of molds; Completion indicator light; Maximum opening diameter without mold: 50mm; Maximum opening diameter with mold: 40mm; Hydraulic tank capacity: 1L; Hydraulic oil capacity: 0.5L; Unused
Machine number: 2-0537 Compressive force: 28 kN Stroke: 60 Table dimensions: 200 x 160 mm Plunger: 60 x 35 mm
Pressure plate stacker Grafoteam PST 26 C; arm length 650mm; suitable for Heidelberg Suprasetter A52-74; optionally with stop interface for Heidelberg Suprasetter A52-74. Plate stacker Grafoteam PST 26 C; arm lenght 650mm; used for Heidelberg Suprasetter A52-74; for option with stop-interface for Heidelberg Suprasetter A52-74.
We offer directly on behalf of the owner : Bending press, second-hand Make : Graebener Maschinentechnik (Gräbener) Type : GRNM Year of construction : 2005 Flexural force max.: 16.000 kN ( 1.600 t ) Tool length : 1,600 mm Data at 520 N/mm2 Pipe diameter max.: 1,524 mm Tube diameter min.: 457 mm Sheet thickness max.: 40 mm Max. pipe length: 13.2 m Pipe length min.: 6m Pipe weight max.: 25 t Total power requirement approx.: 245 kW / 400 V / 50 Hz Approx. space: 27 x 3 m Total weight approx.: 90t / basic machine approx. 65t Further technical data and details on request or see data sheets in photos / PDF The machine was built in 2005, worked until 2021 and was professionally dismantled and packed for transport.
maximum number of results exceeded
please refine your search
