traub a 15 used for sale

Resistance annealing machine This machine anneals (thermally straightens) stainless steel wires from 0.30 - 0.50mm). FUNCTIONAL DESCRIPTION: - The machine enables heating by direct passage of electric current through the wire through the wire (resistance annealing process). The device is equipped with 4 special power stabilisers for regulation, in combination with an optical pyrometer for temperature control and thermoregulation. - The simultaneous heating of the 4 wires takes place in a chamber saturated with inert gas by the electrical contact transmitted by two conductive V-shaped discs (short-circuit rollers). are transmitted. Two further V-shaped discs have the task of guiding the wires. - The system can be integrated into an existing automatic Scholl disc system, which, however, is not not included in the scope of delivery of the machine. Alternatively, the straightened  ...

Heat and Power Plant with an Absorption Chiller An 850 kW combined heat and power plant with an absorption chiller. The systems ran perfectly until the end and all maintenance was carried out. No damage is known. The CHP ran for 51,429 hours of operation. The absorption chiller has run for 42,350 hours. The following components use an overhauled long block or completely overhauled. The components relevant to assemblies for "modernization" were marked: - complete panelling - Interfaceschronk - Oil relubrication pump Mechanically overhauled and electrically tested - Oil level monitoring - Plotter heat exchanger" - Pressure expansion foll3 (if present) - Pressure transducer and temperature sensors - Rubber rails for motor and generator - Clutch element - Air filter inserts - Safety valves and arnot inserts - Sylomer strips - Hot water preheating pump and heating el ...

3x VERSATRONIC RV1s P&P machines which are slow (1200cmp/h) but full fully functional and with a lot of feeders. These machines were manufactured in a UK factory Versatronic. Machine were named Violer, Rosie and Blue. The last one is faster, little better software for fiducial camera for components. All machine are working and were used for prototype and low series like 50pcs electronic or 25pcs or 200pcs electronic. All P&P machines have two cameras, one for fiducial (up camera) and one (down camera) for components. Machines can place without problem components down to 0402 and fine pitch component like QFN or VFQFPN48… Speed for firs two is 1200cmp/h the last one is around 1500cmp/h. All machines have tool changer with 10 positions and one tool for camera auto calibration. Only 5 different tools were used but can be used up to 10 different tools. On one machine you can put u ...

Bobst Cube / monitor with control unit for transfer station, Bobst Alpina 110 II matic. Used and tested. Bobst cube / monitor with control unit for transfer station, Bobst Alpina 100 II matic. Used and tested. BSA07320000TG / H12P+P50S1

Granit marble ATELIERS MAITRE Length: 2000 mm Width: 1200 mm Thickness: 400 mm Height on feet: 910 mm Class 2 Weight: approx 2 T

Banding maretial PW8030150 white paper 40 rolls and PB7030150 brown paper 40 rolls. Banding maretial PW8030150 paper white 40 rolls and PB7030150 paper bouwn 40 rolls.

Atlas Copco ZT30 Air compressor Serial: AIF065086 2000, oil free air cooled screw compressor, operating pressure 8.6Bar, compressor output 69 l/s, motor 30Kw, comes with Ultrafilter International dryer model: HLALD0225 and Abbott air tank

Brand: RENZ Model: inline 60-500cm format Maximum speed: 2200 punching cycles per hour and 1700 binding cycles per hour Dimensions: 5900x2400 cm with hinge Gross weight: 3400 kg supplied with 2 modules: RENZ ASM500 and RENZ ABL500 lit up during the inventory.

Tribloc America 9/8/1 KK Rinser, Filler and closer Cimec America 9/8/1 with 9 rinsing stations, 8 filling valves and 1head crown corker capacity: approx. 1.300 bph bottle sizes: 0,33 and 0,5 ltr. bottles closure: 28 mm crown cork with double pre-evacuation with CIP tulps with siemens S7 PLC length: 3.300 mm with control panel width: 1.600 mm height: 2.600 mm

Ultrasonic Banderolier ATS US 2000 AST-MDM; cleaned and tested; Frame size 900x750mm; Belt width 30mm; suitable for paper (also suitable for TruePaper paper) or foil; Meter reading 795,000 thousand; Compressed air required. Ultrasonic banding machine ATS US 2000 AST-MDM; cleaned and checked;  frame size 900x750mm; band width 30mm; used for paper (also for TruePaper material) or foil; counter 795,000; pressurized air needed.

NEW BIND ADVENTURE spare parts only. From a 2011 machine that lost PLC memory. All parts and electronic components are as new from book clamp, grinding saw and electro motor to manuals.

Key data: 75 , 13 , 15

Screw compressor, 500 V drive, was serviced by Atlas Copco in 2020 and has been out of service since then. Accessories (absorption dryer, refrigeration dryer, oil/condensate separator) available for an extra charge.

Key data: 73 , 3

Screw compressor, 500 V drive, serviced

Ato Rotopacker 3-tube with autom. Bag feeder Zipper 50/4000. Capacity 2400 bags per hour. On request with dedusting system and other accessories possible.

bore diameter: 65 mm throat: 380 mm Control: PLC-Steuerung bore spindle turning speed range: 63 - 1600 U/min table-size: 630 x 500 mm rapid traverse Z-axis: 4,75 m/min boring feeds:: 0,05 - 0,56 mm/U total power requirement: 9 kW weight of the machine ca.: 2,0 t dimensions of the machine ca.: 1,50 x 1,20 x 2,95 m Drilling capacity in steel ST60: 65 mm Drilling capacity in cast iron GG20: 80 mm Thread cutting ST60: M68 Thread cutting GG M72 SPS-controlled automatic drilling machine with Drilling/deep hole drilling/thread cutting Sequence: 1st rapid traverse to start position 2. switch on the speed 3. switch on the drilling feed 4. drilling until the drilling depth is reached 5. return in rapid traverse to start position Manual operation possible (speed and direction of rotation, rapid traverse positioning, Switching the drill feed on/off) Selection of the drill feeds and spindle speed man ...

cutting diameter: 235 mm dimensions of saw-band: 2480 x 27 x 0,9 mm cutting width: 280 x 190 mm cutting speed: 45/90 m/min : 120 mm : 120 mm : 190 mm Impact energy: 170 mm connected load frequency: 400 Volt total power requirement: 1,1 kW weight of the machine ca.: 290 Kg dimensions: 1,2 x 0,8 x 1,2 m Double miter band saw -Miter cuts up to 60° left and 45° right -Vice with quick clamping device -Band tension control -Electr. Automatic cooling The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Manufacturer: CMS Model: Avant-1/B-560-TX3/RR with a digital table Year of Manufacture: 2006 Type of Machine: 4-axis CNC machining center with a moving bridge - Moving bridge design with two racks. Fixed table during machining. - Welded steel support frame stabilized by double heat treatment - Mobile bridge supporting a set of two crossed slide carriages for transverse and vertical movement - Travels: o X axis: 5600mm o Y axis: 2050 mm o Z axis: 300 mm - Working and positioning speed: o X axis from 0 to 60 m/min, positioning speed of 60m/min o Y axis from 0 to 100 m/min, positioning speed of 100m/min o Z axis from 0 to 30 m/min, positioning speed of 30m/min - Automatic centralized lubrication - TX3 vertical head with tool changer mounted on Z-TX3/12/L vertical carriage o Head power: 15kw at 18000 rpm o Programmable rotation speed of 1800 to 24000 rpm o HSK63E cone - 2 ...

SNA-03. Other and Auxiliary Systems Air Technology Systems a) 1 unit Type Wolf KG 160/9391, functional, Built: 1991 b) 1 unit Type Wolf KG 40, functional, Built: 1991 c) 1 unit Type Eichelberger NSR 315, functional, Built: 1991, Rooftop system Manufacturer: Wolf Anlagen Technik GmbH Technical Data: a) 15,400 m³/h; 10 kW; 380V; 1500 rpm; 710 Pa b) 2,400 m³/h; 0.6 kW; 380V; 1500 rpm; 300 Pa c) 3,500 m³/h; 1 kW; 380V; 1500 rpm; 450 Pa Motors: a) 71M06 SIEMENS 1MA5163 4BB; 10 kW; 380V; 1500 rpm; 50Hz, Built: 1991 b) 71M08 Loher ENCV090 SB 84A; 0.6 kW; 380V; 1500 rpm; 50Hz, Built: 1991 c) 71M07 FLENDER ENGV160 MB02A; 10 kW; 380V; 1500 rpm; 50Hz, Built: 1991 Find more here - / Contact us at -

2. Other and Auxiliary Systems SNA-06. Air Technology System, 2 units WOLF KG 100, functional, Built: 1991 Manufacturer: Wolf Anlagen Technik GmbH & CO.KG Technical Data: 6750/6050 m³/h; 15 kW; 1500 rpm; 650 Pa Motors: 65M01 Wolf UD112M; 4 kW; 380V; 1500 rpm; 50Hz, Built: 1991 65M02 Wolf UD112M; 4 kW; 380V; 1500 rpm; 50Hz, Built: 1991 65M03 Wolf UD100LB; 3 kW; 380V; 1500 rpm; 50Hz, Built: 1991 65M04 Wolf UD100LB; 3 kW; 380V; 1500 rpm; 50Hz, Built: 1991 Additionally, 2 refrigeration compressors DWM Copeland, Built: 1992 Type DMRH 750EWM/000; Capacity 26.5 m³/h; 1550 rpm Find more here - / Contact us at -

2. Other and Auxiliary Systems - SNA SNA-08. Air Technology System, 2 units Type Wolf KG 250, functional, Built: 1991 Manufacturer: Wolf Anlagen Technik GmbH Technical Data: 20250 m³/h; 10 kW; 1500 rpm; 1050 Pa Motors: 71M01 LOHER DNGW 160LB 04A; 5 kW; 380V; 1500 rpm; 50Hz, Built: 1991 71M02 LOHER DNGW 160VB 040; 5 kW; 380V; 1500 rpm; 50Hz, Built: 1991 Find more here - / Contact us at -

Manufacturer: Syntegon Model: AFG 5026 Year of Manufacture: 2019 Type of Machine: Filling and Sealing Machine for Vials with Powder Condition: Not used Key Features: - Zoning concept for infeed, filling, outfeed, and drive area - Best accessibility and simplified cleaning procedure - Innovative transport system for continuous and intermittent operations - Vertically rotating mechanism - High output, even with 100% IPC (In-Process Control) - Ideal for wall installation - Optimized Design: - Vertical wall design for best operability - One-side operability for streamlined workflow - Suitable for integration with barrier systems - In-wall installation for space efficiency Find more here - / Contact us at -

Manufacturer: KRONES Series: Autokol Year of Make: 2005 Capacity: 10,000 B/hr Formats: 500ml, 800ml Label type: self-adhesive; front/rear

Dimensions (L,W): 2000 x 1200 mm Weight: , kg tiltable yes/no: nein Bauerle work table ------------------------ Length 2000mm Width 1200mm Height approx. 900 mm (height adjustable) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

gebr. Aerial work platform telescopic, mobile, battery-operated, with boom - Lifting height: approx. 9 meters - Load capacity: 125 kg - Working height: 11 meters - Platform size: approx. 650 x 650 mm - Battery: without battery - Charger: R 8/12 - Dimensions (folded): 1700 x 700 x 2800 mm - Support (LxW): approx. 1900 x 1800 mm - Number of masts: 1 - Engine power: 0.8 kwh Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out. Payload max. approx.: 125 kg ext. Length approx.: 9 m Machine weight: 350 kg Total Power Requirement: Battery Colour: blue

Used autoclave ASCA, type: 250 E -renewed- - Boiler capacity: 250 litres - Electrically heated - Boiler, core temperature and F-value adjustable - New temperature sensor - New drain hose - Electrics completely checked - Digital control - Auto-signaling - Device on wheels, mobile - Condition: Very good, ready to use The device is in pristine condition and is ready to use right out of the box. Visits and test runs are possible by arrangement.

CNC assembly line Brand: Alberti Type: BMF new machine Equipment for automatic insertion of fittings, plinth parts, drawer runners and many more. Can be equipped with automatic screwing devices, gluing indications and press-in tools. Plant expandable with many possible hardware feeding stations. This Alberti line can be customized according to your specifications. Machine bed made of welded steel tube structure, the upper part is made of aluminum frame. Components of the line: - Feeding - Processing zone with transport rollers - destacking Work table: - Driven PVC rollers at the inlet. Usable length: 2500mm, usable width: 840mm - Reference table with PVC rollers Usable length: 2500mm, working height: 840mm, adjustable +/- 30mm - Driven PVC rollers at the outlet Usable length: 2500mm, usable width: 840mm - Vertical workpiece clamps, autom. adjusted to wor ...

Acoustic hoods für IMA edge banding machines in various versions and dimensions available from stock Modifications / new lacquering available for a surcharge.

New shredder Brand: Reinbold Type: AZR 600 technical details: hopper opening: approx. 600 x 800 mm input height: approx. 1.640 mm hopper volume: approx. 0,6 m³ rotor working width: approx. 600 mm rotor diam.: 252 mm main motor power: 18,5 kW - 400 V - 50 Hz. - 3 Ph. hydraulic motor power: 0,75 kW - 400 V - 50 Hz. - 3 Ph. rotor speed: approx. 90 U/min tools: 15 pcs. round knives screen size: 40 mm connecting piece diam.: approx. 160 mm air speed: 28 m/s weight: approx. 1.300 kg

CNC drilling machine Make: Alberti Type: Vector SH New machine This CNC drilling machine machines workpieces from above with 29 spindles and has 4 controlled axes. Optionally, the Vector is available as Modulo-SH with a total of two machining heads (top with 30 spindles and bottom with 7 spindles). Machining head, working from above Manual or automatic loading and stacking with longitudinal workpiece transport Monolithic frame in welded strong steel Independent control of all axes with drilling cycle optimisation 4 independent axes X Workpiece transport along the X axis with vacuum suction cup for automatic alignment Y Machining head W Lateral pressure control Z Machining depth control Remark: Max. Workpiece dimensions: 3000x1200x50mm Min. workpiece dimensions: 300x130x12mm Geometry of workpieces: Length > Width / Length = Width / Length < 20% Width Machi ...

New CNC working machine brand: Cosmec Type: Smart 30, 5 Achsen Configuration example: other equipment possible on request The smart serie: - Flexibility through cantilever construction - Best equipped for door processing - Protection by laser system (instead of step mats) - Especially good for machining light / small workpieces The controlling: OSAI CNC system control + Aspan CAD-CAM software: - Aspan uses simple commands to execute the machining process - By entering dimensions you can precisely position the machining operations - The machining operations are displayed on the virtual workpiece. - Diverse macros facilitate programming (of holes, slots, linear milling, arc milling...) Aspan Doors - Software module for easy creation of programs for door processing. - Different door types are already stored (doors with milled arches, round doors...) - Doors can ...

Granulate supply Make: ADOLPH Type: G-Trans 25 for continuous granulate supply on edge banding machines technical details: System for a machine line with 4 pre-melters (standard) Pos.1.1 1 basic unit for bag-emptying G-Trans® 25 Portal for Big-Bags with hanging emptying: Solid steel frame in 40 mm square-tube profile, torsion-stiff welded construction, main pillars with base plate for dowel-anchorage. Solid steel welded construction in square-tube profile, with fork-lift lugs, 4 hooks and tapered guide pins for easy touchdown on the portal. Sufficient stability for 1.500 kg weight. Supporting area with bars and stacking corners. Material container in powder-coated steel, with cone for free-flowing bulk materials. Filler plug diam. 300 mm. Filler opening 350 x 350 mm with sliding cover. 5/8 plugs for granules transport NW 25 Stack frame  ...

Offer 25078 Specifications: - Cutting range at 90° around 550 mm - flat 570 x 550 mm - Cutting speed infinitely variable 20 to 100 m/min - Hydr. Raising + lowering the saw frame - Cutting pressure infinitely adjustable 0 to 10 m/min - Material replenishment machine - Stop length 500 mm - Total drive power approx. 400 V / 5.7 kW -Attack - 2 x roller conveyor 1000 + 3000 mm - Space requirement approx. W 3400 x H 2100 x D 1300 mm - Weight approx. 2100 kg

Manufacturer: IMA, Motor mit Getriebe: yes, Getriebe: K803AB0570D132L4, Amper 1: 50, Power kW: 9,2, N1-U/min: 1598, Motor mit Getriebe: yes, Getriebe: K803AB0570D132L4, Year :1996

Manufacturer: Siemens Achsmotor für Ima Maschine, Type: 1FK6063-6AF71-1AG0, Motor with gear: yes, Maschinennummer: YF M110 5834 02 003, From machine: IMA BIMA, Motor with gear: yes,

Manufacturer: Heesemann Spindelhubgetriebe 2 Stück, Type: aus Heesemann LSM 8, Motor with gear: 2 Stück Verstellung Schleifaggregate, Motor with gear: 2 Stück Verstellung Schleifaggregate,

Manufacturer: Heesemann Spindelhubgetriebe, Type: aus LSM 8, Year: 2 Stück, Year :2 Stück

Manufacturer: SEW EURODRIVE, Type: A2E170-AA11-65/R60DT7ID4BM, Volt: 220/266, Ampere 1: 0.22-0,35, Motor torque Nm: 5, pm: 2700/300, Watt: 46-78, Weight approx. kg: 28,

Manufacturer: WP-ARO, Type: 666120/240/C, Year: Membranenpumpe, Control: B1050623, Year :Membranenpumpe

Manufacturer: Homag, Type: Motorhalterplatte mit pnematischen ein und Ausrücken, From machine: Homag FÜL 526,

Manufacturer: Airlesspumpe B & M, Type: BMP 1132, Year: 2004, Kolbenpumpen gesamt: 1, Transmission ratio: 32:1, Volumenstrom Doppelhub ccm 2: 72, Volumenstrom Doppelhub ccm 2: 72, Compressed air bar max: 256, Pneumatic pump: yes, Wandhalterung: yes, Year :2004

Manufacturer: Biesse, Type: Arrow ATS BAZ 3, Year: 2003, Control: Biesse, Working range X: 3000, Working range Y-axis: 1500, C axis: no, Pendulum processing: yes, Number of milling spindles: 0, Number of tool changers: 1, Number of tools per tool-magazine: 8, Vertical drills-X: 20, Drill vertical Y: 15, Horizontal drills-X: 4, Drill horizontal Y: 2, Traverse table: yes, 2 station allocation: yes, Saw unit: yes, Year :2003

Manufacturer: Hübner Airlessgerät, Type: HP 4/32 RF, Transmission ratio: 30:1, Volumenstrom Doppelhub ccm 2: 27, Volumenstrom Doppelhub ccm 2: 27, Fördermenge: 27 m³, Luftverbrauch bei 6 bar: 8, Compressed air bar max: 256,

Manufacturer: Weeke, Year: 1999, Type: aus Weeke BP 195, Motor mit Getriebe: yes, aus Maschine: 195 Weeke, I-KL: 7,5-10, Motor mit Getriebe: yes, Baugrösse L x B x H mm: Werkzeugaufnahme HSK 63 F/18000-24000 Umin/12 KW Spindel, Year :1999

Manufacturer: Rippert, Type: Abdunstwand, Year: 1990, Control: hand, Filter surface in m³: ca.1800 X 2200 X 300, Exhaust air m³/h: 5000, Exhaust air m³/h: 5000, Year :1990

Compressed air-cleaned dust filter with stainless steel housing, filter area: 10 m², filter media: 4 filter cartridges, incl. ESM-3 control unit and manifold for flange mounting on the underside. Filter was used for dedusting a horizontal mixer for mineral building materials.

2 independently working cutting bridges 2 working zones (1750x1000mm each) High-performance vacuum turbine X servo drive; Y and Z axes 2 high-luminosity projectors Windows 7 operating system Calculator with CNC interface, modem and Ethernet card

Legi-Air 4040Z with Zebra110pax4 label printer and pneumatic stamp. RA1933 Printer manufacturer: Zebra Printer type 110pax4 Control panel: LCD display with status indicator and buttons Print type: thermal transfer printing or direct thermal printing selectable Interfaces: RS 232 Seriel, IEEE 1284 Print media: standard media, tags and RFID media (reading and coding of RFIF labels) label length min: 12,7mm width print media: 16-114mm ribbon width: 25,4-107mm Ribbon length max: 900m Roll size diameter core: 25,4mm Roll size maximum diameter: 101.6mm Resolution: 203 dots/inch (8 dots/mm) dot size 0,125mm x 0,125mm Print speed: 12 inch/second Features: Breite Druckmedium: 16-114mm Breite Farbband: 25,4-107mm Maximale Länge Farbband: 900m Punktgröße: 0,125mm 0,125mm Druckgeschwindigkeit: 12 \/s, 304,8 mm/s Druckertyp: 110Pax4 Druckmedien: Standart, Anhänger und RFID-Etiketten

Key data: 163 KW, 200 kVA

We currently offer: Generator set Aggreko Model No.: QSB7-G6 Engine Cummins Generator Stamford Power: 200 KVA / 163 KW Hz 50 RPM 1500 Year of construction 2012 Hours: 14589 Metrics: L: 4.15m H: 2.50m W: 1.15m Weight: 4887 kg You can find more machines on our website. If you have any further questions, please feel free to contact us. Adel e.K. Commercial Vehicles-Construction Machines Car Recycling Machine Dismantling Gottlieb-Daimler Str. 26 D-74831 Gundelsheim Phone: 0049 1796710242

Bausch Advanced Type 529 IV bag filling & sealing machine with Telstar aseptic isolator system, sequence of operation: VHP Chamber (Decontamination) - Debagging/Bag loading table - IV bag infeed conveyor - Laser engraving - Robot loading - Starwheel transport - Gas purging – Filling (product tank/buffer vessel with 20 litre capacity, mass flow measuring system with 2 flow meters, filling accuracy +/-1.0%, CIP/SIP) - Stoppering - Discharge/Reject Robot - Discharge Chute - Reject Chute - Weigh station/discharge conveyor, Mettler Toledo IPC (in process check weighing) system is capable of performing 100% weight verification of each bag. Fully processed bags exit the discharge conveyor and are transferred to the MettlerToledo scale, where they are weighed. Allen-Bradley ControlLogix PLC with Caitron CR17 touchscreen, machine floor space 4590 x 2649 mm (LxW), machine working height 900+/-30 ...

Key data: 4000 mm, 2000 mm, 575 mm

Pair of cast iron angle plates Drilling diameter: Ø 27 mm Width: 575 mm Depth: 2000 mm Total height: 4000 mm Unit weight: approx 6 T