tos grinder used for sale

The pallet is in the middle of the machine. The ring with the film roll rotates around the load and wraps it. Because the film gripping and sealing unit is attached to the ring, the wrapping process can start and end at any desired height on the load. Characteristics:  Tosa Modell 125 Machine No.: 103743 Year of Construction: 2010

Weld beveller, weld bevel former, weld seam preparation, bevel forming machine, edge milling machine Manufacturer: TOS Hulin Type: HHP 12 Working length: 12 m Maximal workpiece thickness: 80 mm

215 MW Toshiba Inlet Steam Turbine & Generator (Unused and well maintained) New in 2008, this Power Plant has never been used and is available for immediate inspection and delivery. Never having been used, the Plant has no wear whatsoever. The Steam Turbine: Extraction & condensing, Inlet pressure: 104 bar, Output: 215MW Extractions: MP2: 22 bar, MPI: 10 bar, LP: 4.5 bar, Feed Water: 0.4 bar Minimum load: • No extractions, Only bleeds, Steam flow: 45 kg/s Maximum load: Steam flow: 270 kg/s The turbine is a Single Flow Extraction Condensing type. Steam initially enters the steam inlet flange near the end of the high pressure section and flows through the turbine stages toward the generator end of the unit. After passing through the turbine stages, the steam is exhausted to condenser. The exhaust hood is keyed to the foundation plates at a point near its center  ...

HOV 25

Bezel, stick, lynette -Max. Passage: Ø 107 mm -Tip height: 180 mm -Edition: gray cast iron -technical drawing with the photos -Dimensions: 370/340/H80 mm -Weight: 16 kg

Bezel, stick, lynette -max. passage: Ø 107 mm -Tip height: 180 mm -Edition: gray cast iron -Technical drawing in the photos -Dimensions: 370/340/H80 mm -Weight: 16 kg

Diameter: 500 mm Module: 6 mm Axial travel: 0 mm MACH-id    5215 MAKE        TOS CZ TYPE          OHO 50 YOP SPECIFICATIONS External workpiece Ø Max. 500 Ø  Max. Modul Max.     6 Weight approx.     100 Kg Max. Workpiece height      125 mm Speeds / ranges      355 Rpm Power      4 kW DIMENSIONS Length       2000 mm Width        1000 mm Height      2000 mm

Table length: 1250 mm Table width: 250 mm Longitudinal X: 800 mm Cross Y: 370 mm Vertical Z: 470 mm MAKE   TOS Kurim TYPE     FNK 25 A YEAR    1998 SPECIFICATIONS X - Travel   800 mm Y - Travel   370 mm Z - Travel   470 mm Table Length x Width   1250 x 250 mm Table load in kG   500 Kg Spindle Taper    ISO 40 kW power on spindle   3 kW Spindle speeds / ranges    4500 Rpm DIMENSIONS Length   2300 mm Width    1600 mm Height   2300 mm

Center height: 0 mm Center distance: 2000 mm Spindle bore: 77 mm SPECIFICATIONS Swing over bed Ø  505 mm Control  Conventionel Swing over cross slide  270 mm Swing in the gap Ø  700 mm Distance between centres  2000 mm Spindle bore  77 mm Spindle speeds / ranges  2000 Rpm Power  7.5 Kw DIMENSIONS Length  4100 mm Width  1250 mm Height  1800 mm  

Table length: 1800 mm Table width: 630 mm Longitudinal X: 1400 mm Cross Y: 630 mm Vertical Z: 630 mm Positions ATC: 0   SPECIFICATIONS X - Travel  1400 mm Y - Travel  630 mm Z - Travel  630 mm bed / plano / portal / moving column Universal bed milling Controll  3 axis digital read out Table Length x Width  1800 x 630 mm Spindle Taper  Bt 50kW power on spindle 22 kW

Center height: 0 mm Center distance: 4000 mm Spindle bore: 102 mm Make TOS SU 125 Type SU 125 x 4 Year 80 er Heavy Duty turning lathe Centre height (mm)Swing bed = 1.250 Center distance (mm)Support = 940 Spindle bore DBC = 4.000 Bore = 1024 chuck 1250 3 x steady rest  

Bezel, stick, lynette -Max. Passage: Ø 150 mm -Tip height: 320 mm -Dimensions: 650/500/H110 mm -Weight: 50 kg

Table length: 3000 mm Table width: 800 mm Longitudinal X: 3000 mm Cross Y: 800 mm Vertical Z: 1000 mm Positions ATC: 0   CNC Brand: Heidenhain CNC Model: TNC 355 Make TosTypeFSS-8 Year 1991 Tos FSS 80 CNC bedmilling machine Table length (mm) 3000 Table width (mm) 800 Longitudinal X (mm) 3000 Cross Y (mm) 800 Vertical Z (mm)1000 630 mm CNC Rotary table Iso 50 Automatic head CNC Heidenhain TNC 355

Tailstock counter bearing for dividing head, dividing attachment -Tip height: 95-115 mm -Recording: MK2 -Dimensions: 180/100/H110 mm -Weight: 4 kg

Tailstock counter bearing for dividing head, dividing attachment -Tip height: 120 mm -Dimensions: 230/130/H150 mm -Weight: 10 kg

Length: 1000 mm Width: 800 mm Height: 2000 mm Number of T-slots: 11   Size T-slots: 175 mm Type of material: Cast Iron   Make TOS Varnsdorf Type UU 200Year 2010 Capacity (metric tons)D = 1.000 Stroke (mm)W = 800 Distance Column/center (throat) mm H = 2.000Table length (mm) Weight = 2.500 Table width (mm)T Size = 22 H12T Pitch = 175 mm Number = 11 slotted New Price = 24.000 Euro a pair ! Cast Iron We can offer a pair ( 2 in Stock ) Very little used ! Beautiful Condition !  

tags for table feed box

Table diameter: 1000 mm Turning diameter: 0 mm Turning height: 630 mm Motor power: 40 HP/kW Positions ATC: 0   Positions APC: 0   Make TOS SKJ 8F Type SKJ 8 F Year 1984 Singel column vertical borer TOS SKJ 8 F Centre height (mm)Swing = 1.000 Center distance (mm) Height = 630 Spindle boreLoad = 2.500 Kg Speeds = 500 Rpm5 pos. revolver 2 axis digital read out

Copy head, copy head, copy device, copy lathe -heavy copy head for: lathe -without: hydraulic unit -Guide rails: 2 -and additional equipment -Dimensions: 1100/170/H370 mm -Weight: 143 kg

Tailstock, counter bearing for dividing head, dividing attachment -Tip height: 100 mm -Socket: Ø 12 mm -Dimensions: 111/120/H170 mm -Weight: 4 kg

Center height: 840 mm Center distance: 2000 mm Spindle bore: 128 mm Make TOS SUA 8 Type Celakovice SUA 80 Numeric Year 2001 TOS Celakovice SUA 80 Numerisch gesteuerte Centre height (mm) Swing bed = 840 Center distance (mm) DBC = 2.000 Spindle bore Bore = 128 HeidenHain Manuel Plus Steady rest fixed 3 chuck 500 mm  

Table length: 1800 mm Table width: 1600 mm Longitudinal X: 3500 mm Cross Y: 2000 mm Vertical Z: 800 mm Positions ATC: 0   CNC Brand: Heidenhain CNC Model: TNC 415 Make TOS WHN13 CNC Type WHN 13 CNC Year 1996 TNC 415 in 5 Aixs Spindle diameter (mm) 130/iso50/37kW Table length (mm) L = 1.800 Table width (mm) W = 1.600 Longitudinal X (mm)X = 3.500 Cross Y (mm) Y = 2.000 Pos ATC Z = 800 Number APC.W = 1.250 Speeds 1500 Rpm Rapid = 8000 mm Feed = 6000 mm  

Spindle diameter: 0 mm Cross X: 2000 mm Vertical Y: 1400 mm Table length: 1400 mm Table width: 1250 mm Positions ATC: 60   Number of pallets: 2   CNC Brand: Heidenhain CNC Model: TNC 415 Make TOS WHN11 Type WHN 110 MC Q Year 1994 TNC 415 in 5 Aixs Spindle diameter (mm)110/iso50/37kW Table length (mm)L = 1.400 Table width (mm)W = 1.250 Longitudinal X (mm)X = 2.000 Cross Y (mm)Y = 1.400 Pos ATCZ = 1.250 Number APC.W = 500 Spindle 2500 Rpm ATC chain 60 positionsPallet changer 2 x

Spindle diameter: 130 mm Cross X: 3500 mm Vertical Y: 2000 mm Table length: 2200 mm Table width: 1800 mm Positions ATC: 60   Number of pallets: 0   CNC Brand: Heidenhain CNC Model: TNC 430 Make TOS WHQ13 CNC Type WHQ 13 CNC Year 2004 TNC 430 in 5 Axis Spindle diameter (mm) 130/3000/37kW Table length (mm) L = 2.200 Table width (mm) W = 1.800 Longitudinal X (mm) X = 3.500 Cross Y (mm) Y = 2.000 Pos ATC Z = 1.250 Number APC .W = 800 ATC 60 position 20 bar high pressure coolant  

Spindle diameter: 130 mm Cross X: 3500 mm Vertical Y: 2000 mm Table length: 1800 mm Table width: 1600 mm Positions ATC: 0   Number of pallets: 0   CNC Brand: Heidenhain CNC Model: TNC 415 Make TOS WH13 CNC Type 1996 Year Heidenhain TNC 415 - 5 Axis tos wh13 cnc cnc table borer tisch bohrwerk kotter Spindle diameter (mm)130/iso50/37kw Table length (mm)1800 Table width (mm)1600 Longitudinal X (mm)3500 Cross Y (mm) 2000 Pos ATC 1250 Number APC.w = 800 1500 rpm      

Spindle diameter: 105 mm Cross X: 1800 mm Vertical Y: 1250 mm Table length: 1400 mm Table width: 1250 mm Positions ATC: 0   Number of pallets: 0   CNC Brand: Heidenhain CNC Model: TNC 426 Make TOS WH105 CNC Type WH 105 CNC Year 1998 Tos WH 105 CNC with TNC 426 - 5 Axis Spindle diameter (mm)105 / iso50 / 28 kW Table length (mm) L = 1.400 Table width (mm) W = 1.250 Longitudinal X (mm)X = 1.800 Cross Y (mm)Y = 1.250 Z = 1.250 W = 630 CNC TNC 426 - 5 AxisSpeeds 2800 Rpm  

Turning diameter: 1050 mm Turning length: 4000 mm Turret positions: 0 CNC Brand: Heidenhain CNC Model: Manuel Plus Make TOS Variant  Type SUA 100 CNC Variant Year 11 / 2001 tos variant HeidenHain MANUEL PLUS draaibank Centre height (mm)Swing bed =  1.050 Center distance (mm)Swing sup = 730 Spindle bore DBC = 4.000 Bore = 1154 Chuck 800 mm 3 x Steady rest Mot. tailstock Feed top slide Work load 8 T  

Inv. Num. : 5849 Type: IS 220 GN Producer: TOSHIBA Created: 2002 Parameters: Clamping force: 2150 kN Screw diameter: 50 mm Injection capacity: 490 cm³ Injection mass: 450 g Min. height of the clamping plate: 870 mm Min. width of the clamping plate: 820 mm Distance between stands (horizontal): 610 mm Distance between stands (vertical): 560 mm Ejector force: 140 kN Ejector stroke length: 800 mm Maximum spray pressure: 201 MPa Opening the mold: 1060 mm Machine length: 5900 mm Machine width: 1340 mm Machine height: 1840 mm Spray weight: 8600 kg

The pallet is located in the middle of the machine. The ring with the film roll rotates around the load and wraps it. Since the film gripping and closing unit is attached to the ring, the winding process can begin and end at any desired height of the load. Properties: Tosa Model 125 Machine No.: 103743 Year of construction: 2010

Spindle size: dia 230 / ISO 60 X travel: 9000-25000 mm Y travel: 5000 mm Z travel: 1500 mm W travel: 1750 mm Spindle speed: 800 RPM Rotary table: - Surface: 4000 x 4000 mm - Travel: 2500 mm

Tos SUA 125 CNC Lathe The lathe can fit 1200mm with wires. Tip distance 2000mm. Includes a metric four-jaw tool. Now attached 600mm. Machine year model 2011.

TOS 400 X 2000 BHU 40A Cylindrical Grinding Machine The machine is in very good condition

Turning machine make TOS type Galanta Zyklotronic HAD 40/75Machine -No: 400507596001 Year 1996Turning length: 750 mmTop height: 230 mmCircumference diameter over bed: 400 mmCircumferential diameter over cross slide: 230 mmCircumference diameter in the offset: 460 mmSpindle mount: DIN 52027 / B 6 CamlockSpindle bore: 50.8 mmSpeed range: 20 - 3500 rpm.Feed: 0.001 - 9999 mm / min.Rapid traverse: 6.0 / 3.0 m / min.Drive power / connected load: 7.5 kW / 13 kVAWeight approx: 1760 kgOutside dimensions approx: 2100 x 1200 x 1725 mmWith- CNC control FAGOR 800 T CNC- 3-jaw chuck- revolving center point- Multifix steel holder with multiple insertsused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for ...

CNC Milling Machine Fabr. TOS CELAKOVICE Type FNG 32 NCMash. -No: 7200075Table longitudinal path X: 600 mmUpper arm lateral travel Y: 400 mmTable perpendicular path Z: 400 mmSpindle mount: ISA 40stepless speeds: 10 - 3150 rpm.stepless feed rates in 3 axes: 1 - 9000 mm / min.Weight approx: 2.6 tDrive power: 10 kVAWith- CNC control Heidenhain TNC 155- rigid angle tablelittle usedPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Circulation diameter over bed ... 500mm Distance between stands ... 2000mm workpiece weight ... 600kg Circulation diameter via support ... 270mm Main engine power ... 5.5kW L x W x H ... 1100 x 3575mm Machine weight ... 1845kg complete general overhaul in 2022, CE certificate, new cover, Machine in good condition, possible to test under power.

Displacement of the X-axis: 850 mm Displacement of the Y-axis: 300 mm Displacement of the Z-axis: 420 mm Spindle holder: ISO 50 Spindle speeds: 45 - 2,000 rpm. Digital display: Heidenhain 2-axis Table size: 1200 x 320 mm Feed X and Y: 14 - 900 mm/min. Feed Z:4 - 250mm/min. Rapid traverse X and Y: 2,800 mm/min. Rapid traverse Z:800 mm/min. Equipped with: - Cooling device - Machine clamp Country of origin: Czech Republic Spindle motor: 5.5 kW Machine weight: 3,300 kg Machine LxWxH:300 x 270 x 200 cm

Clamping surface of the table 950x3000 mm Bed length 6000 mm Table movement 2750 mm Passage between stands 1260 mm Machine weight 34 000 kg

X=3500mm Y=2000mm Z=1250mm W=800mm H=360° spindle 130 mm, ISO 50, max. 1600 rpm table 1600 x 1800 mm with a load of 12000 kg with Siemens electric and CNC Heidenhain TNC 415B Oil cooled: Schimpke. Dismantled. The machine has been used very little = in very good technical condition.

Year of manufacture/SO/GO: -/-/2005 The machine is in good technical condition, it is possible to test it by agreement. Modernization in 2005, digitally controlled horizon. Machine weight 13400 kg. Diameter of the working spindle 100mm. ISO 50 spindle taper. Maximum workpiece weight 3000kg.

The machine is in good technical condition. Working spindle diameter: 100mm Transverse table adjustment: 1250mm

The machine is in good technical condition. Working spindle diameter: 90mm Transverse table adjustment: 1120mm. After agreement, the possibility of testing. Accessories: digital measuring, angles.

The machine is in good technical condition, it is possible to test it by agreement. Work table 1800 x 1800mm. Machine dimensions: 7150 x 6280mm, height 5164mm. Main engine 80kW.

Description Sell a very stable tool milling machine. The manufacturer is TOS. Condition used, fully functional. The machine is sold because of the closure of the production. Clamping surface table 2001000mm Longitudinal movement 650mm Transverse movement 300mm Vertical movement 420mm All 3 axes with feed and rapid traverse Feeds longitudinal, transverse 14-900 mm/min 13 steps Vertical 4-250mm/min Rapid traverse longitudinal, transverse 2800 mm/min Vertical 800 mm/min Speed range 31.5 to 1400 1/min // Staggered in 12 speed levels Coolant pump Accessories SK40 pictures about 10pcs Collets SK50 to SK40 Adapter Chuck Dimensions 1.91.72m high Weight approx. 2,5to Machine is ready for collection on a Euro pallet and can be loaded on site with forklift

Machine weight: 13400 kg Total power of the machine:: 20 kW Diameter of the working spindle: 100 mm Spindle taper: ISO 50 Spindle speed: 4 - 1400 rpm Table clamping surface: 1000 x 1120 mm

Horizontal boring mill WH10NC

The machine is in good technical condition. Working spindle diameter: 100m Clamping surface of the table: 1000x1120 By prior arrangement, the possibility of a tour in progress.

The machine is in good technical condition. Working spindle diameter: 80mm Table dimensions: 900x1120mm By prior arrangement, the possibility of a tour in progress.

in good technical condition. Working spindle diameter: 100m Clamping surface of the table: 1000x1120 A tour is possible by prior arrangement.

Machine weight: 17500 kg Total power of the machine:: 10 kW Diameter of the working spindle: 100 mm Spindle taper: ISO 50 Spindle speed: 7.1 - 1200 rpm Table clamping surface: 1250 x 1250 mm

Point lathe SU 63 A in good condition Machine weight: 5600 kg Circulating diameter above the bed: 630 mm Revolving diameter above support: 360 mm Distance between spikes: 2000 mm