129,235 used machines on RESALE, but how to find them? Machine Search
Simatic Panel, Operator Panel, Machine Control, Interface Panel, Control Unit, Operating Panel, Control Panel -Manufacturer: Ilsemann, Control Panel -Type: 216 -Interface: V24/RS232 -Dimensions: 205/130/H60 mm -Weight: 0.9 kg
M. No.: 322 Max. film width 700-800 mm Equipment / Additional information: -GREINER STACKING / Transfer device R3 (Ref. No.: 95002.24) // M. No.: 00020 // Age: 1998 Heating from above and below Material PS and PP were processed 450 Ps // 350 Pp The following tools were used on the machine: 8-way WZ-Ø95 and 15-way WZ-Ø73 and 15-way WZ-Ø86 Packaging was produced especially for the dairy industry. The cycles are 18-25 strokes - depending on the cup weight.
Gearbox, Angle Gear, Worm Gear -Manufacturer: Bonfiglioli, bevel gear from packaging machine ILAPAK Astra-STD -Type: RAN 20/SB -Translation: i = 1:1 -Shaft: Ø 20 x 50 mm -Direction of rotation: see photo -Dimensions: 240/210/H75 mm -Weight: 4.1 kg
Vacuum pump LABORTECHNIK ILMENAU 1DS1 Pumping speed: 1 m3/h Ultimate pressure: 0,0,000 08 Torr ( 0.107 mbar ) motor: VEM EWR 71.2/4 ( EWR71.2/4 ) 0.18 kW 1410 rpm 220 V 1AC IP 44 used, tested ! Dimension: 320 x 160 x 210 mm
Illumina MISeq, good condition New-generation sequencer / for DNA Find more here - / Contact us at -
Yamato Multihead weigher Model: ADW-510SW 10 head Year: 2015 2kg drop Ilapak VT2000 VFFS Bagger 400mm jaw Year: 2005 Complete with gantry & Stairs 2600mm x 2600mm Incline conveyor 400mm wide
2019 WK Systemtechnik ILS 600 – HTL – Ionline Lubrication System Dickschickt preservation system. The oil is applied via nozzles The spray system is a minimum quantity spray system for high-precision dosing of preservative oil. With the spray system you can be coated or oiled reproducibly. By spraying using two-substance nozzles, the finest layer thicknesses can be applied without contact and a wide viscosity range can be covered. The forming medium is in a closed circuit; the excess pressure created by the spray air in the chamber is sucked off at the inlet and outlet using a vacuum lock, so there is no environmental pollution. General data Dimensions (WxHxD) without conveyor units 2486mmx2080mmx2722mm Dimensions with open doors 3265mmx3510mmx2722mm Weight approx. 2500 KG Electrical connection Supply voltage 400 Volt / 50 Hz Power 15kVA Fuse protection 35 A Control v ...
Speeds: 15-100 PPM 64-Program Memory No product No bag PLC controlled color touch screen Misplaced product detection
SINGLE MULTIHEAD WEIGHER FEEDING - 2XBAGGERS MACHINES ONLY WITH TWIN OUTFEED CONVEYORS - NO GANTRY ISHIDA MULTIHEAD WEIGHER MODEL: CCW-RS-216B-2D-30-SS YEAR: 2011 16 HEAD ILAPAK TWIN BAGGERS YEAR: 2011 MODEL: VEGATRONIC 500 300MM JAW
Age 1989 Consisting of: Indramat Servomotor Indexing With auto-start facility SEW Eurodrive Servomotor Indexing Max. material width 730 mm Max. Indexing length 300 mm Top & Lower heaters, total connected load top & bottom heaters 74.2 kW Drive Motor 6.93 kW Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Hydraulic Plug Assist, Max. Part height 125 mm Bosch-Rexroth Hydraulic Power Pack Control Cabinet with Optimised Schleicher (PLC) Controls Encoder on Main Shaft Auto Lubrication Pump Inline ILLIG UG70b Counter/ Stacker, On Sale on a Special Price!, Film width: 700 mm, Form Area: 680 x 280 mm, Infeed length: 300 mm, max. draw: 125 mm
Manufacturer: Ilcam Kantenbearbeitung, Year: ca.1990, Monting of the machine: Verleimteil/Kappen/Vorfräsen/Zieklinge, Min-max edge material mm: 0,5-12, Work piece width min-max mm: 65, Min.-max. workpiece height in mm: 10-55, Min-max feed m/min: 10-20, Premilling: no, Fine milling: yes, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, Pre-milling: yes, Bevel milling: yes, Radius scraper: yes, Year :ca.1990
Age 1999, Consisting of:, Unwind Stand, Preheater ILLIG VWH72, Indramat Servomotor Indexing, Print Registering for Preprinted Film, Max. Film width 610 mm, Max. Thickness range 0.18 to 2.5 mm, Hardened Transport Rails, Double Heating, Heating Load 41.0 kW, Heaters move forwards automatically with pneumatic control, Sheet Sag Control, Form Area 550 x 400 mm, Forming & Punching in Mold with integrated Steel Rule Die, Positive Draw 20 mm, Negative Draw 20 to 40 mm, Trimming Force 50kN., Top and Lower Platens Moved by separate Indramat Servomotors, Heavy duty Toggles on both upper & Lower Platen, Stacking/ Counting Station, Waste Material Winder, Inline ILLIG RS75b Grinder with Blower, Suitable for PS, OPS, PP, PE, PVC etc., PLC: Siemens S5, PLC: Siemens S5, Max Film width: 610 mm, Form Area: 550 x 400 mm
A universal Illig double-stroke thermoforming machine is available. Form dimensions X/Y: 960mm/560mm, max. drawing depth: 280mm, max. panel dimensions X/Y: 960mm/560mm, motor power: 1.5kW, heating power: 16.3kW, heating zones: top and bottom. On-site inspection is possible.
Three Illig punching machines are available for the precise punching of thermoformed plastic parts from film material. Working width: approx. 900mm, working height: approx. 120mm, roller diameter: approx. 196mm, machine dimensions X/Y/Z: approx. 2500mm/1300mm/1600mm, weight: approx. 750kg. Including two hydraulic punching machines Wolf EHPT 6E and two manual swivel arm punching machines. On-site inspection is possible.
Bar diameter min./max.: 5mm/102mm, bar length min./max.: 150mm/1200mm, machine length: approx. 1950mm, machine width: approx. 950mm, machine height: spindle height+345mm, machine weight: approx. 450kg. Documentation available. On-site inspection is possible.
Age 1990, refurbished in 2003 Consisting of : With auto-start facility Unwind Stand Indramat Servomotor Indexing Max. material width 730 mm Max. Indexing length 300 mm Top & Lower heaters, total connected load top & bottom heaters 74.2 kW Drive Motor 6.93 kW Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 680 x 280 mm Pneumatic Plug Assist, Max. Part height 125 mm Control Cabinet with Optimised Schleicher (PLC) Controls Auto Lubrication Pump Inline ILLIG UG70b Counter/ Stacker, with delivery conveyor Inline Grinder with Blower EXW our Warehouse Enger, Germany, max. mateerial width: 730 mm, max. Form Area: 680 x 280 mm, Infeed length: 300 mm, max. draw: 125 mm
Age 1988:- Technical data ILLIG STAL 80 The ILLIG STAL80 can work Inline with any Thermoformer, or it can be used Off-Line as a stand-alone Trim Press. In Stock at our Warehouse in Enger, Germany, Punching table area max: 1000 x 510 mm, Material width max: 800 mm, Infeed length: 20 – 400 mm, Stroke height: 200 mm, Mold height: 272 mm, Punching pressure: 20 000 daN, Drive capacity: 4.16 kW, Total length: 3950 mm, Total width: 2385 mm, Weight approx: 3600 Kg
ILLIG PLS75b Inline Counter/ Stacker, with Hole Punch Station, age 2006, Max. Stacking Area: 750 x 350 mm, Min Height of formed product: 25 mm, Max. height of Formed Product: 150 mm, Min. dia. of product : Ø 40 mm, Max. dia. of Product: Ø 150 mm, Max. length of Product Stack: 730 mm, Output rate of Product Stacks: 1200 Stacks/ hr, Rotating Head to neatly remove Products from the Thermoformer Mold with integrated suction, Inline Hole Punch Station, Inline Counter Stacker Station, Compressed Air: 0.2 L at 6 bar, approximately, Total Drive Rating: 19 kW, Electrical specifications: 400 V, 3 phase, 50Hz (N/ PE), Cross delivery conveyor station for counted cups., All Motors are Indramat Servo Motors, Siemens SIMATIC TOUCH LED Operator Control Panel with Touch Pad Controls, Siemens S7 PLC Controls, Delivers Counted Cups/ Containers at Right Angles to machine direction, New original ILLIG Gea ...
Used ILLIG STAL80 Trim Press, age 2004:-, Technical data ILLIG STAL 80 :, Punching table area max. 1000 x 510 mm, Material width max. 800 mm, Infeed length 20 - 400 mm, Stroke height 200 mm, Mold height 272 mm, Part height (positive and negative) max. 100 mm, Number of strokes (infinitely variable) 25 - 130 /min, Trimmed Parts are stacked through the Punch Tool, The Skeletal Waste is fed directly into the Grinder, Punching pressure 20 000 daN, Drive capacity 4.16 kW, Servomotor Indexing of sheet, Laser control Technology for v. low tolerances in the difference in the Hole Punch Position, ILLIG RS75 Under the Trim Press Grinder, Motor 8.3 kW, Condition: v.good, Condition: v.good
Age 2007, Consisting of :-, Siemens S7 PLC Controls Indramat Servomotor Siemens SINAMICS Motor Drive Rittal Control Cabinet Cooling Unit with Temperature Display With Snap -Stacking Brush Stacking Cascade Stacking The Counter/ Stacker is in v. good production, This ILLIG SZS73 was working Inline with a Generation 3 ILLIG RDM70K Line., Effective Working Area: 740 x 340 mm, Max. Part Height: 150 mm, Formed Part Stacking Length: 800 mm
Production line is in good condition
REF-2662 ILPRA FOODPACK SPEEDY V/G TRAY SEALER Automatic tray sealer. Manufacturer: ILPRA. Series: FOODPACK. Model: FP SPEEDY V/G. Serial no.: FP7291. Year: 2006. Busch vacuum pump. Inert gas. Voltage: 400 V. Max. production (only sealing): 10 cycles/min. Current mould type: 2 round trays of 110 mm diameter. Overall dimensions (mm): 2,870 x 900 x 1,600 (LxWxH). Weight: approx. 700 kg.
A cylinder roll punching machine Adolf Illig is available. Pass-through width: approx. 850mm, pass-through height: approx. 120mm, roll diameter: approx. 190mm, table dimensions X/Y/Z: 2x approx. 1200mm/1200mm, working height: approx. 800mm, machine dimensions X/Y/Z: approx. 2700mm/1350mm/1550mm, weight: approx. 900kg. An on-site inspection is possible.
Manufacturer: MiSeq Model: Illumina Year of Manufacture: 2015 the device has performed 472 runs so far. Electrical Information - Line Voltage: 100V–240V - Frequency: 50/60Hz - Power Consumption: 400W Find more here - / Contact us at -
Machine name: Packaging machine used (thermoforming line) Manufacturer: Adolf Illig Type: SB 53C - DIN Year of Make: 1990 Drive motor: 1.24 kW Dimensions: L 1,600 x W 1,135 x H 2,710 mm Curb weight: 500 kg Tech. Documentation: Yes Remark: Heating capacity: 4.5 kW (15 ceramic surface emitters) Vacuum system: Degree of vacuum max. 0.95 kp/cm2 Formats: Forming area: 405×500 mm Carton size: 400×495 mm Film width: 445 mm Drawing depth positive: 150 mm Drawing depth negative: 150 mm Packaging height: 150 mm Film roll diameter: 400 mm (blister) Film roll diameter: 350 mm (Skin) Film roll core diameter: 70 mm Condition: Used Price: On request
General SKU114Z459 LocationBarneveld Makeunknown Main Features MaterialStainless steel Volume1000 Ltr. Specified Features - Silo MaterialStainless steel 1.4301 (304) Silo(1x) Closedcheck Capacity1000 Ltr Diameter950mm Cylindrical height1400mm Conical height1200mm Flat topcheck Top connectionsdia. 200mm + 235x300/560mm Outletdia. 300mm (with valve) Information Floorspace1,2x1,2 M Total height3,0 MSilos-Tanks > SilosBrand > - What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!
Cooling/Freezing chamber ILKAZELL -External dimensions: 3450 x 3200 x 2450 mm -Internal dimensions: 3250 x 3000 x 2250 mm -Plate thickness: 100 mm -Door clearance: 1000 mm -Stainless steel floor -Cooling/Freezing unit in set -Stock status: 1 -The chamber is easy to assemble
ILLIG RDM75K Thermoformer age 1998, refurbished in 2019 with Siemens S5 PLC Controls, used only for ca. 50,000 hrs, Consisting of:, ELAU B1 Display with Touchpad controls Thermoformer with auto-start facility Indramat Servomotor Indexing Max. material width 750 mm Max. Indexing length 480 mm Top & Lower heaters, total connected load top & bottom heaters 111.3 kW Auto Transport Rail Spreading for PP Sheet Sag Control Max. Forming Area 700 x 450 mm Hydraulic Cylinder Plug Assist with Bosch Rexroth Hydraulic Power Pack, completely Overhauled in 2019 Max. Part height 150 mm Max. Mold closing force 25,000 daN Auto Lubrication system Siemens S5 PLC Controls New original ILLIG/ RITTAL Control Cabinet Cooling System added in May-2023., No Tooling or Format Parts are included with the Line., Max Stacking Area: 750 x 350 mm, Min dia. of product: Ø 40 mm, Max dia. of Product: Ø 150 mm, Total Dri ...
An untested Ilmenauer laser marking machine including a TBH extraction unit is available. 1) Laser marking machine Ilmenauer Laserzentrum GmbH ILZ LBS 01, year of manufacture: 2000, laser class: 1. 2) TBH LN 200 extraction unit, year of manufacture: 2000, air volume flow rate: 250m³/h, motor power: 1.2kW, machine dimensions X/Y/Z: approx. 1000mm/400mm/400mm, weight: approx. 50kg. On-site inspection is possible.
The Ilpra FS 6000 is equipped with twin stages of all stations, the filling heads are built to fill various products ie. Yoghurt, Cream, Sauces, Milk, Fruit pieces of 1 cm, Custard, Etc. The easy maintenance makes these machines highly recommended in production floors keeping productivity at a steady pace. Ilpra cup fillers are mainly driven by a main motor and signals for the air cylinders to take action on each station. The filling volumes depend on the clients needs, therefor these have a standard filling volume of 50-500 ml per cup, we can enlarge the filling volume by increasing the diameter of the filling cylinder on request., Make: Ilpra , Model: FS 6000, Capacity: 4800, Year of Manufacture: 2003, Filling Volume: 50-500 ml per cup , Cup Dispenser: Automatic twin dispenser , Filling: Twin Filling Heads , Filling Specs: Fruits up to 1 cm pieces , Sealing: Twin Heat Sealing Station , ...
Used ILLIG VHW 72/2 Preheater with 2 x electrically heated rolls. Width 720 mm. 380V 50 Hz 3 ph. Heating Capacity 30 kW. Motor 0.18 kW. Total Amps 48 A. Max. Temp. 130.
REF-2665 ILPRA FS 2500 V/G AUTOMATIC CUP FILLER-SEALER Manufacturer: ILPRA Series: FILL SEAL Model: FS 2500 V/G FL Serial no.: FS1071 Year: 2017 Automatic rotary filling-sealing machine for cups of different materials. Compact and flexible model, tailored to handle a diverse range of food products from liquids and creams to granules, even with solid particles in suspension. Maximum output of approximately 2,500 pieces per hour. Voltage: 400 V + N Overall dimensions (mm): 2,350 x 1,280 x 2,200 (LxWxH) Weight: approx. 900 kg
PET Coextrusion + Inline ILLIG RDKP72g Thermoforming Line, Age 2010, this equipment is suitable for PET, PP & PS Trays, Fruit & Vegetable baskets etc. :-, Inline S Plastic SRL PET Coextrusion line to produce pet sheet in-line with ILLIG RDKP72g 4-Station Thermoformer (.samplastco. hole punch station) Age 2010 :, Maximum output 680 kg/ hr, Maximum sheet width 800 mm, The line includes:, Electrical Control Panel, MSM Plastic Engineering Gravimetric Feeder, fed directly from the PET Dryer + additional Component for masterbatch or additive, Main extruder Model ED 100-40 dia. Ø100 mm, L/D 40, BP Plast BDO X2 100 Double plate hydraulic screen changer, MAAG Gear pump, Co-extruder Model E60-40 dia. Ø60 mm, L/D 40 with Gravimetric feeder, BP Plast Single plate hydraulic screen changer, MAAG Gear pump, 3- Layer (ABA) Melt Feed Adapter, Special extrusion die for PET, width 900 mm, 3-Roll Polished ...
ILLIG RDM70K Mold, dia. Ø70 mm, for PP Cups, 21 Cavities, age 1995, with 1 set of inserts and Stacker basket with Rods with Brushes.
ILLIG RDM70K Mold for Ø75 mm dia. PS Cups, 21-Cavities, with 1 set of inserts, no Stacking Basket, age 1995. missing engraved Cup bottom discs, as these are the intellectual property of the previous owner. Very sparingly used !
Offered is an ILLIG HSA 30 RD - high-performance continuous sealing machine for blister packaging: blister films: PVC, PET APET/PETG, PS, film thickness: 150µm-600µm, lid materials: heat-sealable cardboard, aluminum composite films, Tyvek, sealing area X/Y max. approx. 500mm/300mm, forming depth max. approx. 100mm, 8-18 cycles/minute. Inspection possible by arrangement.
Bagging machine manufactured by TMI, model ILERSAC HLG. Technical characteristics Model ILERSAC HLG Year of manufacture 2012 Transportation Information Weight 3000 Kg Manufactured by TMI
used
used vacuum thermoforming machine from Illig in very good condition little used immediately ready for use Dimensions 6 by 5 meters incl. control cabinet and corresponding phereperie devices Pictures to follow
The Ilpra FS 5000 is equipped with twin stages of all stations, the filling heads are built to fill various products ie. Yoghurt, Cream, Sauces, Milk, Fruit pieces of 1 cm, Custard, Etc. The easy maintenance makes these machines highly recommended in production floors keeping productivity at a steady pace. Ilpra cup fillers are mainly driven by a main motor and signals for the air cylinders to take action on each station. The filling volumes depend on the clients needs, therefor these have a standard filling volume of 50-500 ml per cup, we can enlarge the filling volume by increasing the diameter of the filling cylinder on request., Cup Diameter: 95 mm Outside diameter , Filling Range: 50-500 grams , Capacity: 4800 cups/Hour , Stations: Cup Dispenser -> Filling -> Aluminium Lid Applicator -> Sealing -> Date Stamping -> Out-feed Conveyor , Guarding: Fully Enclosed Cabin , Control Panle: S ...
Used Illig RDM 37/ 10 with top heater, No Sheet Sag Control, Heater moved forward manually, Auto-unwind stand, mechanical indexing, Auto start mechanism, Pneumatic Plug assist, Form Area 475 x 250 mm, Max. Film width 495 mm, Max. Draw 100 mm, Age 1975, basic Machine, in production Condition, Please make an offer !
Bakery freezer Ilsa Past BT 700 for trays 600 x 800 Digital temperature display from -10 to -20°C Connection 230V Used device
bag length: ca. 700 mm bag width: ca. 500 mm work impulse: - total power requirement: 10,2 kW weight of the machine ca.: 0,5 t dimensions of the machine ca.: 2 2 2 m Movie: https://www.youtube.com/watch?v=TGGMb3B2UG0 The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Packaging capacity single jaw/double jaw: 100/200/h, sealing jaw spacing: 150mm, sealing jaw width: 250mm, product length range: 50mm-500mm, product width range: 20mm-230mm, max. product height: 120mm, max. cut-off: 650mm, max. film width: 650mm, max. roll diameter: 350mm, roll core diameter: 76mm, max. roll weight: 40kg, machine weight: approx. 850kg. Documentation available. An on-site inspection is possible.
General SKU327X680 LocationBarneveld CEcheck MakeIlmvac Pressure Working pressure0.0005 Bar Vacuum possiblecheck Main Features MaterialStainless steel Volume63000 Ltr. Motor2.4 KW Specified Features - Vacuum pump MaterialNickel alloy (201) 2.4068 Pumpcheck vacuum Number of pumps:1 Capacity70 m³/h With motor2,40 kW, 400 V, 1365—1440 rpm InletDN35 OutletDN35 Information Type321022 / U 4.70F/K Mach.No.113807 Year of construction2011 Floorspace0,80 x 0,37 m Total height0,30 m Weight60 kgVacuum pumpsIlmvacPumps > Vacuum pumpsBrand > Ilmvac What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!
Pressure blower, radial fan, high pressure radial fan, dust extraction blower, exhaust gas extraction, welding fume extraction, extraction, extraction blower, fan, pressure blower, vacuum blower, ventilation blower, blower, radial blower -Manufacturer: VEB ILKA, radial fan extraction fan -Type: IRHMF160 / 2 see photo type plate -Engine power: 3.4 kW / 2900 rpm -Volume flow: 0.242 - 0.694 m³/s -Inlet: Ø 160 mm -Connection output: 250 x 160 mm -Fan wheel: Ø 500 mm -Dimensions: 780/490/H1030mm -Weight: 88kg
fan, ventilator, electric motor, blower, electric motor, blower, radial fan, emergency ventilation fan, flue gas fan, axial fan, axial fan, axial fan, fan motor -Manufacturer: VEB ILKA, axial fan axial fan -Type: S4D350-AF10-17 -Motor: 25 W 1380 rpm -Voltage: 220/380 V -Dimensions: Ø 380 x 140 mm -Weight: 4.0 kg
electric clutch brake, clutch/brake combination, clutch-brake combination for strapping machine, packaging machine, strapping machine, skinpack machine, wrapping machine, winding machine, drive unit for stretch wrapping machine -Manufacturer: Bonfiglioli, drive unit from packaging machine ILAPAK Astra-STD -Type: GFF 200014/112 EE B3 -Motor: 24 VDC / 35 W -Individual components: see photos -Dimensions: 345/180/H230 mm -Weight: 22 kg
Spindle lifting gear, linear drive, linear gearbox, lifting gear, spindle lifting element, spindle drive, electric actuator, valve drive, actuator, actuator motor, strapping machine, packaging machine, strapping machine, skinpack machine, wrapping machine, winding machine, spindle lifting gear for stretch wrapping system -Manufacturer: SITI, spindle lifting gear from ILAPAK Astra-STD packaging machine -Transmission: Type MI 30 H9 -Shaft: Ø 20 x 270 mm -Motor: ICME 0.09 kW -Dimensions: 395/265/H120 mm -Weight: 7 kg
maximum number of results exceeded
please refine your search
