thyssen meta used for sale

Various metal materials in 15 metal storage bins.

An EHT hydraulic guillotine shear refurbished in 2023 is available. Cutting length: 3000mm, max. sheet thickness steel/VA: 4mm/2mm, backgauge: 10mm-1000mm, adjustment speed: 180mm/s, stroke rate: 18-31 strokes/min, oil volume: 160l. Machine dimensions X/Y/Z: approx. 3700mm/2100mm/2150mm, weight: approx. 4800kg, operating hours: 44024h. The cylinders, blades and hoses were overhauled in 2023. On-site inspection is possible.

A Haco hydraulic shear is available. Working width: 4000mm, max. sheet thickness: 8mm, cutting angle range: 0.5°-3°, stroke rate: 11 strokes/min, backgauge: 1000mm, machine dimensions X/Y/Z: approx. 5000mm/2000mm/1800mm. On-site inspection is possible.

Stock number: D689, Metal detector, stainless steel,, Detectronic type 606-250-1010-2., Inlet H 150 x B 200 mm., Lamella conveyor with L 2500 x W 200 mm. with push-off arm., Max. height 110 mm., Material: Stainless steel AISI 304

L-profile: 120 x 120 x 10 mm flat steel: 300 x 15 mm round/square steel: 40 mm punching: dia 28 x 13 mm U/I-profile: 100 mm

A 3D metal printing machine Concept Laser GmbH in need of repair is available. Technology: Laser melting (SLM)/LaserCusing, working dimensions X/Y/Z: 250mm/250mm/280mm, layer thickness range: 20µm-80µm, max. scanning speed: 6m/s, focus diameter range: 50µm-500µm, laser power: 200W, printing materials: stainless steel/aluminum/titanium/nickel-based alloys/cobalt-chrome. Machine dimensions X/Y/Z: approx. 2450mm/2400mm/1650mm, weight: approx. 2000kg, laser cabinet dimensions X/Y/Z: approx. 600mm/1200mm/1200mm, weight: approx. 180kg, blower dimensions X/Y/Z: approx. 550mm/1450mm/550mm, weight: approx. 70kg. Including various printing materials such as titanium plates, steel plates and aluminum alloys. The machine has CF card defects and the communication between laser GUI and RCU breaks down. Documentation available. On-site inspection is possible.

Pipe measurement 33 cm, length 3.90 m + Steel beam L 5.25 m.H 25 cm. W 12 cm.

Excl tipper

Machine ready for transport

Chip conveyor;

Including: 5x cantilever rack 2x 5800x1150x2000mm, 1x 2000x1150x2200mm, 1x 940x1500x2000mm, 1x 4900x1150x2000mm, metal stock consisting of: metal tubes, corner strips, bars, in various lengths,

Hand lever shears VEB Scherenbau Nossen type ScDH10Knife length: 180 mmSheet thickness: max. 10 mmFlat material: 50x15 mm4-edge solid material: 22x22 mmRound steel: 24 mmAngle steel: 60x7mmT-steel: 60x7mmon mobile undercarriageWeight: approx. 150 kg; used

Equipped with Positron S frequency control

machine ready for transport and to be assessed on viewing day. damage to electrical cabinet / driver

Handheld;

With pneumatic mandrel

Clamping plate, machine table with metal baseClamping table, assembly table, clamping bracketClamping surface: 1200 x 370 mmD- Groove spacing: 90 mmTable height: 870 mm- Slot table used to be a machine table from a milling machine- 4 T-slots 16 mm- Metal substructure with height-adjustable feet- Multi-layer wood panel L x W x H 1200 x 400 x 18 mmOverall dimensions L x W x H 1400 x 770 x 870 mmWeight: 250 kggood condition; used

Capacity: The machine has a cutting capacity of up to approximately 225 mm for round materials and up to 245 x 150 mm for rectangular sections. Saw blade: Uses standard bi-metal saw blades measuring 2450 x 27 x 0.9 mm. Motor: Equipped with a three-phase electric motor (often 0.75 - 1.1 kW) with two cutting speeds. Miter: Possibility of miter cuts, usually from 0 to 60 degrees to the right. Versions: There are different variants, such as the manually operated Zip 290

Folding machine KRAMER type A-toll. II 1000Fabr. No. 48 287 Year of construction 1990Useful length 1060 mmmax. Sheet thickness 3.75 mmStroke of the upper beam 180 mmAdjustability of the bending beam 60 mmBack gauge 480 mmDrive power of bending beam drive 4 kWAdrive power of upper beam drive 1.5 kWNet connection 400 volts, 50 Hz- manual and semi-automatic control- angle adjustment via angle selector- one-piece pointed rail 135- back gauge with hand crank adjustment and simple measurement scale-

Hydraulic guillotine shears STEINER type HTS 30/20 RMasch. No. 315 Year of construction 1982Cutting length 3050 mmCutting thickness 20 mmBack gauge 800 mm controlledMotor power approx. 30 kWNet connection 400 volts, 50 Hz- Back gauge with positioning control ELGO- Back gauge adjustment via ball screws- Safety light barrier SICK front as protection against interference- 3 pieces Material Support arms with ball rollers- Electric foot switch- Replacement knifeSpace requirement of the basic machine L x W x H 4650 x 2610 x 3200

Hydr. Swing cut guillotine shears HERA type HSS IIIFabr. No. 598 Year of manufacture 1986Cutting length 3100 mmCutting thickness 3 mmStand projection 200 mmKnife strokes 25 strokes/min. Mains connection 380 Volt, 50 HzMotor power 3 kW- motorized adjustable back gauge 1070 mm- actual digital display for the back gauge- cutting gap adjustment- cutting length adjustment- front side stop left 1000 mm- 4 pieces sheet metal support arms 1000 mm- el. Foot switchSpace requirement without sheet metal support arms L x W x H 3630 x

Swing-cut guillotine shears KÖLLSCHEN type BSK 2000/2Fabr. No. 69 1307 Year of construction 1969Cutting length 2000 mmCutting thickness 2 mmStand projection 90 mmWorking height 920 mmMains connection 380 volts, 50 HzEngine power 4 kW- Drive via geared motor with brake and crankshaft- mechanical sheet metal hold-down- manual back gauge 500 mm- stop adjustment via 2 handwheels, rear on the backgauge guide with measuring scale- front side stop left 720 mm- electric foot switch- manual

Mitre Cold Circular Saw EISELE Type VMS-III-S-PVTyp No. 430 Fabr. No. 2371 Year of construction 1991Saw range at 90 (round) 120 mmSaw range at 90 (flat) 150 x 110 mmSaw range at 45 (round) 100 mmSaw range at 45 (flat) 120 x 100 mmSaw blade diameter 350 mmSaw blade speed 17 + 34 rpm. Mitre cut 45 to the left, 90 and up to 30(60) to the right, infinitely variableMotor power 2 and 2.6 kWNerg connection 380 volts, 50 Hz- two cutting speed levels over 2 motor speeds-

Vertical band saw PEHAKA type SM 4Fabr. No. 27060 Year of construction approx. 1980Projection 380 mmTable size 620 x 480 mmCutting height 250 mmRoller diameter 400 mmWorking height 1120 mmSaw blade length min. 2900 - max. 3100 mmSaw blade speed 22-125 m/min. infinitely variableMotor power 0.6 / 0.75 kWNet connection 380 volts, 50 Hz- infinitely variable saw blade speed via Vario belt drive with lever adjustment and 2 motor speeds- Saw table tiltable +/- 15- Saw blade butt welding machine IDEAL BS 0-16-

Mitre cold circular saw BERG & SCHMID type MKS 350Year of construction approx. 1980Saw range at 90 Around 110 mmSaw area at 90 Rectangle 160 x 90 mmSaw area at 90 Square 95 x 95 mmSaw area at 45 Round 95 mmSaw area at 45 Rectangle 120 x 90 mmSaw area at 45 Square 80 x 80 mmSaw blade diameter max. 350 mmSaw blade speed 28 and 56 rpm. Motor power approx. 1.8 / 2.5 kW pole-switchableMains connection 380 volts, 50 Hz- motor with 2 electrically switchable speeds- infinitely variable

Sheet thickness iron: 0.75mm, sheet thickness steel: 0.5mm, working width: 780mm, stroke rate: 135/min. An on-site inspection is possible.

Z-conveyor, conveyor belt with metal link belt GÖSSLINGMetall belt conveyor, belt conveyor, floor conveyorMasch. No: 15867 Year of construction 2005Useful length: 3100 mmBelt width: 400 mmFrame profile height: 70 mmInsertion width: 465 mmInsertion length bottom: approx. 1500 mmLength conveyor belt slope: approx. 800 mmLength conveyor belt outlet top: approx. 600 mmHeight offset: approx. 170 mmBelt speed: approx. 22 m/min. Conveying height - discharge height: approx. 1220 to 1390 mmInsertion height: approx. 1050 to 1270Motor power belt drive: approx. 0.37 kWNet connection 400

Qty. 1 Second-hand lathe CNC machine Manufacturer: VERNET BEHRINGER Machine type: FG 2005 CNC Definition: Sheet metal drilling line Year of construction: 2012 Voltage supply: 380 V, 3 ph., 50 Hz, Ground Control voltage: 24 V DC Installed power: 90 kVA Hydraulic unit: 15 l/min Central motor power: 4 kW Medium pressure: 130 bar Oil volume: ≈120 liters Limits of sheet metal dimensions to be machined Min. section: 100 x 100 x 5 mm Max. section: 2000 x 1000 x 40 mm & 1340 x 1000 x 60 mm

A sheet metal guillotine shear and a press brake Wieger are available. 1) Guillotine shear Wieger ESW 5/25, year of manufacture: 1960, max. cutting capacity: 5mm, working width: 2000mm. 2) Press brake Wieger AW 50, press force: 50t, working width: 2500mm. An on-site inspection is possible.

Corner forming machine

Manufacturer: Bystronic Model: BLT 4000 Year of Manufacture: 2001 Type of Machine : C02 Laser Find more here - / Contact us at -

electric shears for metal sheets

Height=1.39 m, Overall length= 2.27 m, Overall width= 0.99 m, Net weight= 66 kg,

Met elektrische achteraanslag Ponscapaciteit: 70 ton Dia x plaatdikte: Ø 28 x 20 mm Maximale slag: 80 mm 40 str / min Keeldiepte: 300 mm Werkhoogte: 1065 mm Maximale snijdikte in plaat: 20 mm Bladlengte: 455 mm 90°-snede: 130 x 130 x 13 mm 45°-snede: 90 x 90 x 10 mm Op maat gesneden rond/vierkant: 45 mm Elektromotor (vermogen): 7,5 kW Lengte: 1800 mm Diepte: 1200 mm Hoogte: 2000 mm Gewicht: 1650 kg

Height=1.16 m, Overall length= 1 m, Overall width= 1.23 m, Net weight= 212 kg,

Saw blade Ø: 400 mm Cutting range round: 130 mm Rectangle: 305 x 40 mm mitred at 45° round: 130 mm Rectangle: 40 mm Cutting speed: 10 m/min Feed speed hydraulically infinitely variable: 0 - 1000 mm/min Saw drive: 380 V, 1.7 kW Weight approx.: 700 kg Space requirement without roller conveyor: 1100 x 1000 x 1900 mm

Height=1.4 m, Overall length= 0.95 m, Overall width= 1.5 m, Net weight= 160 kg,

Height=1.32 m, Overall length= 0.75 m, Overall width= 1.7 m, Net weight= 155 kg,