126,766 used machines on RESALE, but how to find them? Machine Search
servo motor, DC motor, servo gear motor, servo actuator, drive actuator, servo drive -Manufacturer: HD Harmonic Drive, Hi-T Drive SERVO ACTUATOR -Type: RH-8-3006-T-SP -Shaft: Ø 18 x 20 mm -Dimensions: 200/60/H65 mm -Weight: 1.0 kg
Compressor control, compressor control, control panel, control box, control unit -Manufacturer: Boge, compressor control from screw compressor type VLED 30R-11A -Individual components: see photos -Dimensions: 200/110/H150 mm -Weight: 1.2 kg
Specifications: - Max. working width 3040 mm - max. material thickness 4 mm - Manual cutting angle adjustment - Stroke rate up to 34 1/min - Backgauge with positioning control Pos100 - Table height approx. 850 mm - Front angle stop - 2 front support arms - Rear space protection with light barrier - E-foot switch - Pneumatic connection 6 bar - Drive 400 V - Space requirement without support arms approx. W 4000 x H 1400 x D 2100 mm - Weight approx. 4700 kg
hydraulic pump, oil pump, hydraulic unit, hydraulic pump, hydraulic pump, traction motor, drive motor -Manufacturer: Bosch, hydraulic pump -Type: 0 510 425 307 -Shaft: conical Ø 14-17 mm -Flange: Ø 80 mm -Quantity: 1x pump available -Dimensions: 130/90/H120 mm -Weight: 3.4 kg
Key data: 3000 W, 1500 , 1500
Many of our machines are available from stock. Call and ask to find out more. Fiber laser cutting machine FLV-3015-OT-6022 1.5kW Specifications - Maximum sheet size: 3000x1500mm - Positioning accuracy of the X and Y axes:: ±0.05mm/m - Repeatable positioning accuracy of the X and Y axes: ±0.03mm - Maximum speed: 60000mm/min - Maximum acceleration: 0.7G - Maximum load: 1200kg - Nominal power: 1.5kW - Energy requirements: 12.0kW - Source brand: Raycus or MAX Photonics (You can choose) - Feed voltage: 3x400V50Hz - International Protection Rating: IP54 Cutting thickness - Carbon steel: Recommended thickness 20.0mm, maximum thickness 22.0mm - Stainless steel: Recommended thickness 8.0mm, maximum thickness 10.0mm - Aluminum: Recommended thickness 6.0mm, maximum thickness 8.0mm - Brass: recommended thickness 5.0mm, maximum thickness 6.0mm Structure parts The machine i ...
Muller Martini Perfect Binding Line, Equipped With: Endsheet Feeder, Perfect Binder: Muller Martini 3006-18 with Stream Cover Feeder with 18 Stations, Book Block Feeder, Hot-Melt Spine and Side Gluing with Pre-Melter, Spiral Lay Down Balance or Drying Converyor to Trimmer. Three Knife Trimmer: Muller Martini 3670 With Cassettes for Quick Change, Stacker Delivery, Max. Size: 450x310mm, Max. Speed 6.000 Cycles/Hour, Max. Size Head/Tail: 420mm, Max. Size Spine/Front: 305mm, Production: 4.000 Books/Hour.
Aluminium Z-conveyor belt incl. substructure Horizontal range 1,200mm (customizable) Rising range 3,000mm (customizable) 2nd horizontal range: 1,200mm (customizable) Angle in the bend 45 degrees each Feed height: horizontal (individual) Discharge height individually adjustable Construction: height adjustable (can be moved) Conveyor belt width 700mm (customizable) We supply our conveyor belts in PVC, PU, felt or rubber. PU conveyor belt incl. cleats and corrugated edge Drive: Motor 1.1KW (adjustable), speed approx. 0.3m-0.5m/sec Connection 220/240V, 50Hz protection class IP54 Drive etc. ready for connection, motor control optional 8x adjustable machine feet for alignment Scalloped edge: 80x50mm T-65Studs - 150mm 2-layer particularly transversely stable We always have various systems of this type in stock. The delivery time of an individual system is currently ap ...
Inv. Num. : 7570 Type: TruMatic L 3030 Producer: TRUMPF Created: 2001 Parameters: Laser power: 1800 W Work table length: 3000 mm Work table width: 1500 mm Maximum sheet thickness when cutting: 20 mm Feed length X-axis: 3000 mm Y-axis feed length: 1500 mm Feed length Z-axis: 115 mm
MITSUBISHI S6A-300-3 300 HP 1530 RPM (S6A3 MPTK 405 kW 1840 rpm) Dry Weight :+/- 1900 kg Dimensions: 209 x 101 x 137 cm
clamping angle, T-slot plate, clamping table, clamping cube, clamping plate, clamping tower, clamping box -Clamping cube: heavy version -Clamping surface: 405 x 300 mm -Material: steel -Dimensions: see photo technical drawing -Dimensions: 405/300/H200 mm -Weight: 49 kg
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Manufacturer: Parker, hydraulic cylinder stroke 300 mm -Type: J-3LRLS33M -Piston rod: Ø 35 mm -Bore: 82.6 mm -Dimensions: 550/140/H95 mm -Weight: 13.4 kg
Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams -Hydraulic cylinder: single-acting stroke 40 mm -Type: 3003284-1 1-5 -Piston rod: Ø 32 mm / M22 -Hole: Ø 18 mm -Number: 2x cylinders available -Price: per piece -Dimensions: Ø 82 x 330 mm -Weight: 5.7 kg/piece
Try square, locksmithsquare, hair square, precision hair square -Stop angle: leg length 600 x 300 mm -Dimensions: 605/300/H40 mm -Weight: 2.8 kg
Pneumatic cylinder, flat cylinder, pneumatic drive, stamp, flat cylinder -Manufacturer: Festo, flat cylinder stroke 300 mm -Type: unfortunately no longer readable -Piston rod: Ø 16 mm / M12 -Pmax: bar -Dimensions: 465/40/H70 mm -Weight: 2.1 kg
Offer 24245 Specifications: - Feed of the milling unit pneumatically - Work table adjustable in height via handwheel - Horizontal and vertical material tension - Milling cutter diameter up to 300 mm - Max. profile height 190 mm - Max. milling depth 110 mm - Max. milling length 400 mm - Angle-adjustable stop Li + Re 20 90 20 ° - Milling spindle speed 2800 rpm - Drive 400 V / 2.2 kw - Compressed air connection 6 - 8 bar - Air consumption per work cycle approx. 10 l - ELGO digital display for material cross fence - Pneumatic profile clamping - Spraying device - Space requirement approx. W 1100 x H 1500 x D 700 mm - Weight approx. 300 kg
Electric heating: 28 kW Adjustable air circulation Pneumatically controlled fresh air, exhaust air, and smoke damper Cleaning: foam cleaning Smoke feeding: on customer request Smoking material: wood chips Without the after-burning system Installation dimensions of the machine in cm: Width: 158 Length: 145 Height: 275 Trolley dimensions in cm: 100 x 100 x 200
live center, live center, live morse taper, live center, live lathe center, live center, centering cone -Manufacturer: Henninger, rotating centering point centering cone -Type: unfortunately without type designation -Recording: MK5 -Dimensions: Ø 116 x 300 mm -Weight: 8.2 kg
Fixators, leveling units, leveling elements, machine base, machine feet, leveling shoes, machine foundation, leveling shoe, wedge shoe, machine support, leveling foot, spring elements -Spring elements: Machine feet 4 pieces for machine tools and systems -Support surface: 300 x 250 mm -Height: 35 mm -Price: complete -Dimensions each: 300/250/H35 mm -Weight 13.3 kg/piece
Collet chuck, tool holder, tool holder, milling chuck, milling tool -Collet chuck: MK6 -Type: SWN301/3 MK6 SWN 301/1 GR32 -Clamping sleeve: Ø 7 mm -Dimensions: 80/70/295 mm -Weight: 5.6 kg
DMG GILDEMEISTER CTX ALPHA 300 CNC turning center was built in 2008. The machine, designed for machining workpieces with a maximum diameter of 500 mm, is equipped with state-of-the-art technical solutions that guarantee extraordinary accuracy and precision. Machining is performed inside a large, fully illuminated workspace by a reliable spindle and high-quality cutting tools taken from a 12-position turret. In turn, the operator is provided with a state-of-the-art touchscreen control panel with a perfectly optimised FANUC CNC controller. High reliability, precision and structural stability make the GILDEMEISTER CTX ALPHA 300 CNC lathe the perfect choice for even the most intensive production work. The total weight of the machine is approximately 4350 kg. Technical data of the DMG GILDEMEISTER CTX ALPHA 300 lathe - maximum turning diameter: 500 mm - maximum cutting diameter: 200 mm ...
Tailstock, counter bearing for dividing head, dividing head -Manufacturer: Swedturn, Type ST12 CNC 300 tailstock -Quill: hydraulically driven -Dimensions: see photos -Dimensions: 900/650/H450 mm -Weight: 265 kg
Conveyor belt, belt conveyor, metal conveyor belt, wire belt, link belt, round wire link belt, wire eyelet link belt, wire eyelet link belt -Conveyor belt: round wire link belt stainless steel -Width: 600 mm -Length: 3.0 m -Transport dimensions: Ø 110 x 600 mm -Weight: 4.2 kg
Technical data for the shelving system: Shelving system: SSI Schaefer Type: R 3000 Technical data for the installation: Number of rows of shelves: 01 pcs. Shelf length: 1,056 mm Number of fields per row of shelves: 01 pcs. The scope of delivery includes: 02x Shelf stand, used Material colour: sendzimir galvanised Frame profile dimensions: 31 x 60 mm incl. gravel bars and base plates The stands are pre-assembled Height: 2,280 mm Depth: 300 mm 05x Wooden shelf, used Particleboard width: approx. 985 mm Particleboard depth: 217 mm Material thickness: 22 mm 10x Shelf crossbar, second choice (new) Type: KTRZ 31036 Material colour: sendzimir galvanised Z-profile: 60 x 40 x 12 mm Clear width: approx. 994 mm Hole grid: approx. 53 mm Agraffe: 3 HK (hook) Weight | Pcs.: 1,700 kg Max. load per pair of trusses 300 kg with the same weight. Distributed load 10x Un ...
Conveyor belt, belt conveyor, transport belt, belt conveyor, belt conveyor, flat belt conveyor -Manufacturer: Venjakab, belt conveyor on solid base frame, without drive -Webbing: Type H 6.5 m -Belt width: 1985 mm -Conveyor length: 3 m -Transport dimensions: 3060/2430/H940 mm -Weight: 740 kg
Bending tool, die, lower tool, die tool, folding tool, press tool, forming tool, clamp press tool, upper tool -Die tool: Forming tool / Press tool -Length: 300 mm -Dimensions: see photos -Overall dimensions: 300/80/H110 mm -Weight: 17.9 kg
Linear bearing, linear rail, linear guide, roller guide rail, guide carriage, guide rail, roller carriage, electric carriage, linear carriage -Manufacturer: Afag, linear slide electric slide -Type: ES30-300 -Stroke: 300 mm -Shaft: Ø 20 mm -Dimensions: 525/60/120 mm -Weight: 5.8 kg
0: ja Working width: 3000 (3500) mm 0: ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
MIG/MAG hose assembly, MIG/MAG welding gun set, MIG/MAG welding torch -Manufacturer: Dinse, hose package with water-cooled wire feeder -Type: DIX MPZ 2-304 -Length: 8.5 m -Connector: 5-pin -Transport dimensions: 580/450/H130 mm -Weight: 7.1 kg
Silo 3 m³ volume, payload 4200 kg, Net weight 600 kg Diameter 1800 mm, height 2400 / 3430 mm Spout height 1100 mm Outlet NW 250 Inspection/filling lid in silo roof NW 500 Silo butterfly valve Platform + Vertical Ladder
Flat belt pulley, toothed pulley, multi-belt pulley, timing belt pulley -Timing belt pulley: Ø 228 mm -Type: D TB 90-8M-50 -Number of teeth: 90 teeth / Belt width: 50 mm -Mount: Taper clamping bushing 3020-40 / Ø 40 x 50.8 mm -Dimensions: Ø 228 x 60 mm -Weight: 12 kg
Laser engraving machine with 30 watts of laser power - Very few operating hours / used demonstration device (approx. 15 hours) - It's worth taking a look - incl. Windows10 PC 64bit (used / incl. monitor/keyboard/mouse) - Fully installed and adjusted - Engraving software in German - Very easy to use - Switch on and get started - Fiber laser source with 30 watts for high-contrast and fast Markings with very high resolution (see pictures) - Wobble function, e.g. for cleaning metal components - Depth engraving up to 3mm possible - for engraving on many metals (stainless steel, brass, aluminium, etc.) and a lot of plastics - Heavy industrial quality - Complete system / ready for immediate use - Working space approx. 390 x 270 x 350mm (lxwh) - Clamping surface with mounting threads in 50mm increments - LED work area lighting - 50mm pipe connection for smoke extr ...
Laser engraving machine with 30 watts of laser power - Laser source 30 watt CO2 metal tube Demonstration machine, with minimum operating hours (approx. 10 hours) - incl. Windows 10pro 64-bit PC system - incl. 22" screen - Everything is fully installed and adjusted - Engraving software in German - Very easy to use - Switch on and get started - Co2 laser source with 30 watts for high-contrast and fast markings with extremely high resolution - Deep engraving possible - Wobble function - For engraving on e.g. wood, plastic, anodised surfaces, etc. - Heavy industrial quality - Complete system / ready for immediate use - Working space approx. 500 x 600 x 600mm (lxwh) - Clamping surface with mounting threads in 50mm increments - LED work area lighting - 50mm pipe connection for smoke extraction - Engraving area approx. 180 x 180mm - Expandable up to approx. 3 ...
Silo 3 m³ volume, payload 4.8 to, dead weight 980 kg Diameter 1750 mm, height 3450 mm Spout height approx. 1050 mm Outlet NW 250 Blow-in line, vent line Inspection cover NW 500 in silo cylinder Filling lid NW 500 in the silo roof Platform with vertical ladder
Key data: 3000 mm, 3 mm
with automatic hold-down device POS 100 E Control for Motorized Backgauge Single-angle stop 2 front support arms adjustable on linear rail Manual cutting gap adjustment 0.5 - 3 mm a sheet metal transport and stacking device is attached under the fence for transporting and depositing the cuttings Compressed air connection required Security fencing and light barrier available Adjustable back gauge 8 - 1000 mm Colour: grey/blue Total power requirement: 32 A with cutting gap adjustment without cutting angle adjustment Power: 3000x3.0 mm, 4.0 mm aluminum, 1.5 mm stainless steel Dimensions: 4000 x 1600 mm Weight: 4000 kg Machine number: 200034 Machine is repaired, checked, cleaned by a professional and is then fully functional. Test run is carried out.
Center height: 300 mm Center width: 2000 mm Circumferential Ø: over bed 620 mm Spindle bore: 83 mm Spindle mount: size 8 Pick-up cone tailstock: 5 MK Spindle speeds: 14 - 1000 rpm Feeds: longitudinal/flat 0.086-4.842/0.04-2.258 mm/rev Thread pitches: 0.5 - 28 mm Electrical connection: 380/400 V, 15 kW Space requirement: 3600 x 1200 x 1350 mm Weight: 3400 kg
Square, locksmithsquare, hair square, precision hair square -Angle angle: Leg length 300 x 180 mm -Quantity: 1x angle stop available -Dimensions: 305/180/H20 mm -Weight: 0.6 kg
Angle bracket, locksmithsquare, flat angle -Flat angle: Leg length 300 x 200 mm -Quantity: 1x flat angle available -Dimensions: 300/200/H5 mm -Weight: 0.7 kg
Hydraulic power unit, hydraulic pump, universal power unit, hydraulic station -Manufacturer: Sauer Sundstrand, hydraulic unit from Atlantic ATS 3006 guillotine shear -Hydraulic pump: double version -Motor: EMI 7.5 kW / 1440 rpm -Dimensions: 790/330/H295 mm -Weight: 83.6 kg
Up-down sander SAC 4R-300 Working width 300mm Working height 2.5-150mm 4 sanding units 2x Bottom unit 2×5.5kW 2x top chiller 2×5.5kW Sweeping brush top and bottom' 2×0.55kw Adjustable feed on the inverter 4-16m/min Electric grinding height adjustment Ability to work in-line with other machines CE Certified Year of production 2001
Pneumatic cylinders, air cylinders, standard cylinders, clamping cylinders, compact cylinders -Manufacturer: SMC, Compact cylinder type ECDQ2A80-300DC -Stroke: 300 mm -Piston rod: Ø 25 mm -Number: 2 cylinders available -Price: per piece -Dimensions: 420/100/H140 mm -Weight 5.7 kg/pc.
Flange connection, V-flange, pipe flange, stainless steel flange, safety breakaway coupling -Pipe flange: Stainless steel flange -Type: HG/T20592-2009 PL200 PN10 304 -Diameter: Inside 213 mm -Bolt circle: Ø 295 x 22 mm -Dimensions: Ø 340 x 265 mm -Weight: 26.1 kg
Tow hitch, trailer coupling, jaw coupling -Manufacturer: AL-KO, axle braked -Type: B 2000-4 -Brake: Type 3081 A -Brake drum: Ø 325 mm Recess Ø 160 mm / Bolt circle Ø 205 mm -Dimensions: see photos -Transport dimensions: 1750/660/H340 mm -Weight: 134 kg
Display, display module, display panel, multifunction counter, controller, bidirectional counter, preset counter, digital counter -Manufacturer: IVO, Multifunction Digital Counter with 6-digit LED Display -Type: N 214.002AX01 -Item No.: 300949 -Dimensions: 130/110/H50 mm -Weight: 0.4 kg
Type Vacuum tumblers Height 2100 mm Width 1900 mm Length 1800 mm Weight 1100 kg Capacity 300 l Power supply: 400V 50Hz 3N Main Material Stainless steel, acid-resistant Barrel Aeration Valve Yes, Solenoid Valve Variable speed control of the tumbler Smooth adjustment of the barrel speed Cooling jacket tumbler Yes, refrigeration unit built into machine design Loading Loading integrated into the machine
Hand spindle press, mandrel press, spindle press, hand spindle press, printing press, balance printing press -Manufacturer: Allgaier, manual spindle press -Insertion height: 345 mm -Column clearance: 300 mm -Table width: 300 mm / Bore Ø 60 mm -Spindle mount: Ø 40 mm -Dimensions: Ø 1420 x 1780 mm -Weight: 277 kg
Double bench grinder, double grinding machine, pedestal grinder, pedestal grinder -Motor power: 1.35 kW -Speed: 1500 rpm -Grinding discs: Ø 300 x 40 mm -Operating voltage: 380 volts
tapered roller bearings -Outer diameter: 80 mm -Width: 18 mm -Inner diameter: 40 mm -Weight: 0.5 kg
Number of motors: 1 Stück 0: 2500 mm Control: nein Single-sided glazing bead saw Hecht ES 300 A -------------------------------------- swivels from 45° to 45° to fixed stop with automatic feed pneumatic swivel over manual swivel stop with machine base, pneumatic tension Saw blade HM 300 x 3.0/2.2/30 Z 80 Neg. Touch stroke 1.5 m Support 1.5 m with support Key stroke 3 m Support extension from 1.5 m to 3 m with support Table inserts grooved for rebated glazing beads HECHT ASB manual length stop with digital display, 2500 mm (technical information according to the manufacturer - no guarantee!) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
electric motors: DECKEL FP 3 2803 / FP 4 2 power capacity: 1,58 / 1,4 kW volt: 163 / 175 V ampere: 10,8 / 9,3 A weight of the machine ca.: 100 kg dimensions of the machine ca.: 0,80,60,4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Wood chipping machine Low-noise low-speed machine with press drawer WL12/30 Hopper dimensions 1200x1200 Diameter of shaft 368mm 58 cutting blades in two rows 15/20mm Strainer Main motor 30kW Weight approx. 3200kg
maximum number of results exceeded
please refine your search
