tetra pak 200 used for sale

Coolant preparation, coolant filter, suction belt filter HOFFMANN HSF 200 E 220 / 380 V used, tested ! Dimensions: 3300 x 1400 x 1300 mm

Gear motor VEM ZG0 KMRB 63 G4 ( ZG0KMRB63G4 ) 0,37 kW 200 rpm 220 / 380 V 3AC IP44 shaft diameter: Ø 22 mm wavelength: 50 mm groove width: 6 mm motor base: 118 x 155 / 158 mm hole spacing (parallel to the shaft): 95 mm hole spacing ( transverse to shaft ): 130 mm hole diameter: Ø 9 mm New ! Dimensions: 370 x 158 x 200 mm

Sound insulation 1650 x 755 x 200 mm Weight: 30 kg Illustration similar!

Soundproofing 1650 x 1255 x 200 mm Weight: 50 kg Illustration similar!

Gear motor VEM ZG2 KMR 90 L 4 ( ZG2KMR90L4 ) 2,2,2 kW 200 rpm 220 / 380 V IP44 shaft diameter: Ø 32 mm flange diameter: Ø 200 mm bolt circle spacing 160 mm used, tested ! Dimensions: 550 x 245 x 200 mm

coolant filter system, coolant system, filter system MZ, FILTER TECHNOLOGY WEIDA EMA 200 coolant tank: 1290 x 610 x 350 mm ( approx. 250 l ) magnetic roller: Ø 130 mm x 450 mm speed: 440 rpm engine: MS562-4 0,0,09 kW 1320 rpm 220 / 380 V 3AC K&S PG056 Gear ratio: 3 coolant pump1: Engine: MEZ BRNO 4AP71-2S 0,37 kW 2800 rpm 220 / 380 V 3AC coolant pump2: Motor: IMB14-71x0,37x3000 0,37 kW 2850 rpm 220 / 380 V 3AC used, tested ! Dimensions: 1210 x 600 x 510 mm

Industrial gas spring, gas spring Eriks RX-GF-19-200-CC-200 stroke 200 mm extended 464 mm extension force 200 N

Roll-up door PAGUS 1500 x 2000 mm Alu ! Drive SEW SF47 DT80K4/BMG/1S 0.55 kW 83 rpm 220 / 380 V used, tested ! Dimensions: ca 1860 x 520 x 190 mm

Gas sampler, gas detector BERNT GmbH GP-2000 nominal flow rate: 0.5 l/min Dimensions: 305 x 250 x 140 mm

Gear motor with clutch and sprocket BAUER D 1A41AHZ/253 2,2,2 kW 200 rpm 220 / 380 V 3AC IP65 shaft diameter: Ø 30 mm coupling with double sprocket Ø 80 / 100 mm, 15 teeth coupling diameter: Ø 215 mm Replacement motor for Kaltenbach HDM 800 / 900 cold circular saw, among others ! used, tested ! Dimensions: 600 x 220 x 300 mm

Scooter ITOH DENKI Power Moller PMA - 5 - 250 - 3 - 200 - G Diameter: Ø 63 mm Length: 250 mm Dimensions: 360 x 70 x 70 mm

Scooter ITOH DENKI Power Moller PM 570 AS - 15 - 250 - 3 - 200 - G diameter: Ø 63 mm length: 250 mm unused ! Dimensions: 310 x 70 x 70 mm

Scooter ITOH DENKI Power Moller PM 570 AS - 15 - 250 - 3 - 200 - G Diameter: Ø 63 mm Length: 250 mm Dimensions: 310 x 70 x 70 mm

DC gear motor, gear motor GANSOW DPO MRP5 0,66 kW 200 rpm 24 V DC IP44 shaft diameter: Ø 25 mm flan diameter: Ø 150 mm used, tested ! Dimensions: 325 x 180 x 180 mm

Universal soldering and welding torch ROTHENBERGER Allgas 2000 with oxygen and propane gas cylinder mobile Dimensions: 440 x 440 x850 mm

Engraving machine WMW FG 200 x 400 Table size: 400 x 200 mm workpiece height max.: 300 mm Stencil table: 380 x 380 mm x-travel: 500 mm y-travel: 250 mm z-travel: 325 mm Speed range: 2500 to 20000 rpm 0.25 kW 380 V with various stencils ! Dimensions: 1000 x 1200 x 1500 mm

work platform, lifting platform, scissor lift table NEUERO EFAP built: 2005 load capacity: 2000 kg working surface: 2300 x 1000 mm working surface height max: 1650 mm min: 650 mm with travel drive for rails ! control is incomplete used, tested ! 220 / 380 V Dimensions: 5000 x 1300 x 850 mm

Cutting ring set PAGUS D 15 L ( D15L ) Inner diameter: Ø 15 mm outer diameter: Ø 18 mm cutting ring length: 10 mm Material: Steel, galvanized Cutting ring set consists of 200 pieces ! unused ! Dimensions: 150 x 120 x 60 mm

Jigsaw, high-frequency tool, high-frequency machine FEIN ASt 836 0,36 KW 1640 rpm 200 V 300 Hz untested ! Dimensions: 330 x 170 x 70 mm

Drill, high-frequency tool, high-frequency machine FEIN DS 848 0.75 KW 420 rpm 200 V 300 Hz untested ! Dimensions: 450 x 230 x 90 mm

Drilling machine, high-frequency tool, high-frequency machine FEIN ASg 836 0.36 KW 420 rpm 200 V 300 Hz untested ! Dimensions: 290 x 200 x 70 mm

hydraulic motor, hydraulic motor DANFOSS OMR 200 ( OMR200 ) 151-0245 nmax: 300 rpm pmax: 175 bar Vmax: 200 cm3/revolution shaft diameter: Ø 32 mm Flange diameter ( inside ): Ø 83 mm used, tested ! Dimension: 230 x 130 x 130 mm

welding table, straightening table, straightening flap, work table, clamping table straightening plate, straightening table PAGUS 2000 x 680 mm height: 840 mm Dimensions: 2000 x 700 x 850 mm

Pressure relief valve REXROTH DB20K3-1X/200XY R900493310 max . 200 bar max. 300 l/min Adjustment type: lockable rotary knob with scale New ! Dimensions ( valve ): 140 x 30 x 35 mm Dimensions ( packaging ): 170 x 40 x 40 mm

Magnetic clamping plate PAGUS diameter Ø 200 mm square: 8 mm Dimensions: 240 x 240 x 100 mm

Cutter mandrel, tool holder WMW 4 x 30 x 200 ( 4x30x200 ) TGL 30-4113 MK4 shaft diameter: Ø 20 mm Tool holder: Ø 30 mm New ! Dimensions: 490 x 50 x 50 mm

Hydraulic cylinder, double-acting REXROTH CD 70 C 40/18 - 200 ( CD70C40/18-200 ) Z11/01HCDM44A 893559 Piston diameter: Ø 40 mm Rod diameter: Ø 18 mm stroke: 200 mm rod thread: M10 x 1,5, Length: 25mm Flange: 85 x 51mm hole spacing: 70 / 37 mm 4x bore: Ø 8.5 mm used, tested ! Dimensions: 267 x 85 x 58 mm

Hydraulic cylinder, double-acting REXROTH CD 70 F 40/18 - 200 ( CD70F40/18-200 ) Z10/01HEDM11A 890515 piston diameter: Ø 40 mm rod diameter: Ø 18 mm stroke: 200 mm rod female thread: M10 x 1,5, Depth: 25mm Base: 291 x 93mm hole spacing: 273 / 70 mm 4x bore: Ø 10.5 mm used, tested ! Dimensions: 327 x 93 x 52 mm

Hydraulic cylinder, double-acting, with extended piston rod PARKER CTC-3LRL18MC piston diameter: Ø 38,1 mm Rod diameter: Ø 16 mm stroke: 200 mm Rod thread: M12 x 1.5, length: 15 mm rod extension: 20 mm Flange: 51 x 51 mm bolt circle: Ø 51 mm 4x studs: M6 x 1.0, length: 20 mm used, tested ! Dimensions: 379 x 51 x 51 mm

Hydraulic cylinder, double-acting, with piston rod on both sides PARKER CKC-3LRLS29MC piston diameter: Ø 38,1 mm Rod diameter: Ø 25.4 mm stroke: 200 mm rod female thread: 2x M20 x 1.5, depth: 40 mm foot: 305 x 90 mm hole spacing: 286 / 70 mm 4x Bore: Ø 11.0 mm used, tested ! Dimensions: 575 x 90 x 52 mm

Diaphragm accumulator, bladder accumulator, pressure accumulator HYDAC SBO200-1E1/112U-200AB Content: 1,,0 l Pmax.: 200 bar T: -10 - 80°C Hydraulic connection: Female thread: G1/2 ( inch ) / External thread: M33 x 1.5 Width across flats: 41 mm Filling connection: Internal thread: Male thread: M28 x 1.5 New ! Dimensions: 205 x 137 x 137 mm

Hydraulic cylinder, double-acting VALMET 200/110x300 DWN32401031.04 Piston diameter: Ø 200 mm rod diameter: Ø 110 mm stroke: 300 mm 2x rod end, without bearing necessary bearing diameter ( outside ): Ø 160 mm, bearing width: 50 mm used, repaired, checked ! Dimensions: 1100 x 270 x 270 mm

Hydraulic cylinder, double-acting VALMET 200/110x300 DWN32401031.04 Piston diameter: Ø 200 mm Rod diameter: Ø 110 mm stroke: 300 mm 2x rod end, with bearing bearing diameter ( inside ): Ø 110 mm, bearing width: 70 mm used, repaired, checked ! Dimensions: 1100 x 270 x 270 mm

Hydraulic cylinder, differential cylinder REXROTH CD/T3/MP5/50/22/200/F/11/B/3/3/H/H/E/M/W/W 0010648134/0010 piston diameter: Ø 50 mm rod diameter Ø 22 mm stroke: 200 mm unused ! Dimensions: 450 x 75 x 85 mm

Wire rope hoist, hoist, electric wire rope hoist BALKANCAR T 0243 MA ( T0243MA ) Year: 1982 Capacity: 2000 kg Lifting height: 12 m Lifting speed: 1,1,4 / 8 m/min 380 V 3AC 50 Hz approx. 10 m control cable New ! Dimensions: 1100 x 560 x 460 mm Dimensions(wooden box): 1200 x 800 x 600 mm

Chain hoist with electric chassis, trolley PFAFF SILBERBLAU Type PL10 2004B1 Capacity: 2000 kg Lifting height: 3,3,000 kgbr /br /lifting height: 3,000 kgbr /br /lifting height: 3,3,2004B1br /br / 0 m Lifting speed: 4 / 1 m/min Electric chassis type CHM20 Travel speed 20 m/min 1.75 / 0.45 kW voltage: 400 V 3AC, 50 Hz IP55 used, tested ! Dimensions ( without cable ): 650 x 450 x 730 mm

Pressure vessels, compressed air tanks SILIT - WERKE 3.5239.4-EG capacity: 200 litres zul. Operating pressure: 15 bar max. Operating temperature: +100 °C Main connectors: 1x 21/4 ( inches ), 1x 21/2 ( inches ) various auxiliary connectors: 3/8 ( inches ) to 1 ( inches ) Material: Steel, painted used, tested ! Dimensions: 1450 x 500 x 1100 mm

Lever clamp, sheet metal clamp, sheet metal gripper, lifting clamp TAKRAF KH 2 ( KH2 ) Load capacity: 2 Mp ( approx. 2000 kg ) Gripping range: 5 - 50 mm used, tested ! Dimensions: 370 x 260 x 195 mm

hook harness, bottom bottle, crane bottle, hook bottle TAKRAF 2000 kg hook load: 2000 kp ( 2000 kg ) 2-strand, with single hook Ø 35 mm with pocket wheel: diameter Ø 80 mm for round steel chain: length ( outside ): 30 mm, width ( outside ): 22 mm, Diameter: Ø 7 mm New ! Dimensions: 290 x 90 x 100 mm

Heavy duty rack, pallet rack KÖGL Type: pull-out rack Order number: P87 0087036303-Z78 Shelf load: max. 10000 kg bay load: max. 4000 kg shelf width: 1520 mm, shelf height: 2000 mm, shelf depth: 950 mm 3 pull-out compartments ( height adjustable ) Compartment width: 1240 mm, compartment depth: 750 mm ( 800 mm without aluminium profile ) The heavy-duty shelf must be anchored in the floor ! used, checked ! Dimensions: 1520 x 950 x 2000 mm

Tool cabinet with 8 mm steel plate Pagus Heavy version width: 2000 mm depth: 1000 mm height: 1020 mm made of sheet steel with 2 doors with 2 bays New ! 330 kg

Axial fan, axial duct fan VEM, ILKA VAV140/50 0,04 m3/s 45 Pa impeller: Ø 140 mm Pipe inner diameter: Ø 146 mm motor: 0.025 kW 2000 rpm 220 V AC 50 Hz New ! Dimensions: 150 x 150 x 70 mm

Control cabinet fan, filter fan PFANNENBERG TYPE: PF 2000 ( PF2000 ) Filtered air flow: 56 m3/h front dimensions. 150 x 150 mm Mounting opening: 125 x 125 mm Motor : 5 Watt 24 V DC IP54 New ! Dimensions ( fan ): 150 x 150 x 67 mm Dimensions ( packaging ): 160 x 160 x 8 mm

Adjustable pharyngeal gauge, pharyngeal gauge FEINMESSZEUGFABRIK SUHL 200 - 250 mm im Holzkasten used, tested ! Dial gauge unused ! Dimensions: 520 x 300 x 50 mm

concentricity tester, concentricity tester PAGUS center height: 200 mm face plate: outer Ø: 335 mm height with jaws: 128 mm slotted holes: Ø 16 x 45 / 55 mm flange for face plate: Ø 150, PCD: Ø 105 mm Table for measuring stand: 305 x 53 mm, working height: 45 mm Measuring stand: Radius of action: 250 mm Measuring height: 300 mm Stand: 260 x 70 x 44 mm used, tested ! Dimensions: 390 x 380 x 450 mm

caliper, analogue workshop caliper MASSI TGL 9252 0 - 2000 mm Accuracy: ±1.0 mm beak length: 250 mm with fine adjustment and locking screw used, tested ! Speditionsware, shipping costs on request ! Dimensions : 2265 x 320 x 20 mm

welding table, straightening table, straightening flap, work table, clamping table measuring table PAGUS 130 x 200 mm measuring height: max. 525 mm Projection: 120 mm working surface: 130 x 200 mm Working height: 70 mm dial gauge mount: Ø 27,5 mm, Length: 52.5 mm Column: Diameter: Ø 50 mm, Length: 600 mm used, tested ! Dimensions: 305 x 130 x 670 mm

Magnetic clamping plate, electric PAGUS 200 x 78 mm 4x clamping surface: 200 x 78 mm 220 V 0.14 A approx. 2.2 m connection cable used, tested ! Dimensions ( without cable ): 293 x 78 x 78 mm

3-jaw chuck, three-jaw chuck, lathe chuck PAGUS Ø 200 mm outer Ø: 200 mm centering Ø: 155 mm bolt circle Ø (chuck) : 182 mm bore Ø: 65 mm height with jaws: 104 mm including feed wrench used, checked! Dimensions ( lathe chuck ): 200 x 200 x 104 mm

Turntable, rotatable base plate for machine vices WMW, NILES D/1-200 outer ring: Ø 188 / 210 mm Inner ring: Ø 110 / 142 mm Bolt holder: Ø 30 mm Groove width: 23 / 39 mm Groove depth: 33 mm groove (bottom): Width. 20 mm, Depth: 6 mm, Length: 350 with graduation 2x U - hole: Ø 22 x 30 mm New ! Dimensions: 350 x 293 x 42 mm