tetra pa 250 used for sale

peak heights: 250 mm point distance: 1500 mm bar pass: 105 mm

Capacity up to 250 kg/h Melting container capacity 35 kg stainless steel with casting device with vibration table Connection 8.2 kVA Electrical heating resistance 4.5 kW with cooling compressor, coolant R134a Cooling capacity 7.5 kW with touchscreen operation with 1 year warranty, operating errors excluded

specifications: - Welding current 300 A 60% ED - 230 A 100% ED - Welding current adjustable from 10 A to 300 A - Current consumption 400 V / 19.5 A / 10.7 kVA - with: - E.- welding cable - Ground cable - Connection cable - Space requirement approx. W 600 x H 900 x D 1000 mm - Weight approx. 180 kg

faceplate diameter: 2500 mm swing diameter: 3200 mm turning height: 3100 mm Control: R&D type: MTC 2x-2 workpiece weight: 20000 kg slide adjustment: 1600 mm side head - cross travel: 1000 mm Tool changer: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 2,5 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 92 mm tool adaptor: 35 mm speed: 3,5 m/min total power requirement: 1,5+0,55 kW weight of the machine ca.: 320 kg dimensions of the machine ca.: 1200x700x1200 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 2,5 mm roll-body distance: 260 mm throat: 500 mm distance between roll centers: 92 mm tool adaptor: 35 mm speed: 3,5 m/min total power requirement: 1,5 kW weight of the machine ca.: 295 kg dimensions of the machine ca.: 1200x700x1200 mm Domestic equipments: - motor driven beading machine - 3 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding wheel diameter: 200 mm no. of working stations: 2 Stück turning speeds: 2800 U/min dimensions of grinding wheel: mm grinding motor: 0,55 kW shaft cross cut: 32x40 mm total power requirement: kW weight of the machine ca.: 250 kg dimensions of the machine ca.: 1 x 0,6 x 1,2 m - Swing table 420 x 220mm - on the side. Movement 40mm - infeed against grinding wheel 70mm - Degree of inclination 30 ° - Grinding guide grinding device - Inclination of the mounting bracket 20 ° - Adjustment of the mounting bracket 45 ° - Infeed against grinding wheel 80mm - Height adjustment 90mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

saw blade diameter: 70 - 230 mm sawblade width: 12 mm hole of sawblade: 10 - 50 mm grinding wheel diameter: 120 mm grinding wheel width: 6 mm grinding wheel hole diameter: 32 mm no. of teeth: 30 - 400 total power requirement: 0,33 kW weight of the machine ca.: 350 kg dimensions of the machine ca.: 0,80 x 0,70 x 1,70 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

press capacity: 250 t spindle diameter: 160 mm ram stroke range: 180 mm stroke speed: 71 Hub/min column daylight: 450 mm table surface area: 560x450 mm ram surface: 450x400 mm total power requirement: 12 kW weight of the machine ca.: 9 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter over bed: 250 mm turning diameter over slide rest: 130 mm turning length: 700 mm turning speeds: 115 - 1620 U/min centre height: 125 mm spindle bore: 27 mm tailstock quill taper MT: 2 tailstock quill stroke: 40 mm metric threading: 0,2 - 3,5 mm thread - inch: 8 - 56 inch. thread - module: 0,2 - 12,5 mm swival range +/-: Oberschlitten 45 ° connected load frequency: 400 V total power requirement: 0,75 kW weight of the machine ca.: 0,15 t dimensions of the machine ca.: 1,41 x 0,61 x 0,41 m Equipped with - 2-axis digital measuring system with position indicator - manufactured according to DIN 8606 - 27 mm spindle passage - adjustable guideways by adjustable strips - Strong engine with 0.75 kW - High resolution of the axis spindles for exact positioning Delivery: 3-jaw chuck 100 mm, change gear set, splash guard 3-axis digital measuring system fully assembled. The data for ...

turning diameter over bed: 250 mm turning diameter over slide rest: 130 mm turning length: 700 mm turning speeds: 115 - 1620 U/min centre height: 125 mm spindle bore: 27 mm tailstock quill taper MT: 2 tailstock quill stroke: 40 mm metric threading: 0,2 - 3,5 mm thread - inch: 8 - 56 inch. thread - module: 0,2 - 12,5 mm swival range +/-: Oberschlitten 45 ° connected load frequency: 400 V total power requirement: 0,75 kW weight of the machine ca.: 0,15 t dimensions of the machine ca.: 1,41 x 0,61 x 0,41 m Equipped with - 2-axis digital measuring system with position indicator - manufactured according to DIN 8606 - 27 mm spindle passage - adjustable guideways by adjustable strips - Strong engine with 0.75 kW - High resolution of the axis spindles for exact positioning Delivery: 3-jaw chuck 100 mm, change gear set, splash guard 3-axis digital measuring system fully assembled. The data for ...

capacity 90 degrees: round: 255 mm capacity 90 degrees: square: 240 mm : 300 x 180 saw band length: 2.765 x 27 x 0,9 mm mm table height: 950 mm band speed: 18 - 110 m/min total power requirement: 1,5 kW weight of the machine ca.: 0,42 t dimensions of the machine ca.: 1,23 x 1,7 x 1,75 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

screw size: 84 mm injection shot weight in Polysterol: unbkt. g/PS closing pressure: 440 kN volumn: 1660 volt: V total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

PART NUMBER: 7545 Specifications: - Track width 250mm - shaft width 220mm - max disc diameter 300mm - blade hole diameter 60mm - cutting height 100mm - table top width 650mm - table top length 1460mm –in advance: - 2 rows of ratchets - smooth sliding shaft - shaft with saws - smooth, sliding shaft – from below: -Guide -Triggers -caterpillar - 2 types of feed speed + smooth - central lubrication - feed motor 1.2kW - main motor 21kW - extraction spigot diameter 180mm - total dimensions length/width/height 1700x1450x1500mm - weight about 1800kg ADVANTAGES – Italian production – DTR documentation – a solid machine – used multirip saw, very good condition Net price: 25900 PLN Net price: 6023 EUR depending on the price of 4.30 EUR (Prices may change with higher fluctuations)

workpiece length: 610 mm work piece width: 180 mm workpiece height: 240 mm dia. of cup wheel: 200 mm table-size: Ø 280 mm spindle throat: 250 mm spindle speed:: 3000 U/min. voltage: 380 V total power requirement: 2,94 kW weight of the machine ca.: 430 kg dimensions of the machine ca.: 0,85 x 0,75 x 1,90 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

PART NUMBER: 7544 Specifications: - Track width 250mm - working width of the shaft 220mm - max disc diameter 300mm - blade hole diameter 60mm - max cutting height 100mm - width of the table top with extension 560mm - table top length 1580mm –in advance: - ratchets 2 rows - Slip roller, metal, pressure roller - shaft with saws - smooth, metal, slip roller – from below: - slip roller - guide strip -Triggers -caterpillar - central lubrication of the track - smooth speed control on the inverter - feed motor 1.5kW - main engine 15kW - extraction spigot diameter 170mm - total dimensions length/width/height 1950x1500x1600mm - weight about 1800kg ADVANTAGES – Italian production – central lubrication of the track – very good condition – used multi-rip saw Net price: 33900 PLN Net price: 7884 EUR depending on the price of 4.30 EUR (Pric ...

sheet width: 2500 mm plate thickness: 30 mm pre-bending: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Stocknumber 2210015 Type of machine Hydr. 3-roll bending machine Make HAUSLER Type RMA 2500/30 Build in 1962 Type of control conventional Additional information max. widht 2500 mm Max. plate thickness 30 mm 3 rolls diameter upper oll 450 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

x-travel: 2550 mm y-travel: 900 mm z-travel: 1200 mm Control: Heidenhain type: 355 table surface area: 2900x800 mm Center of spindle to wall or column: 1000 mm spindle taper ISO: 50 : chip conveyor: tool clamping electrical: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m About usmore than 400 machines in the warehouse over 12000 m² storage area, crane capacity 70 tmore than 1000 items accessories for your workshopYou want to sell machines production lines or your company, then talk to us. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

GeneralCNC Turning Centre; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways620 mmTransverse stroke260 mmLongitudinal stroke795 mmClamping chuck diameter max.315 mmWork spindle (left)Spindle bore91 mmSpindle diametre on front bearing140 mmMain drive 1Drive power (100% DC)22 kWSpeed range- 4000 rpmMax. torque (40% DC)525 NmTorque (100% DC)410 NmAccuracy at point stopping0,001 degreeTool holder 1Number of tool stations12 Shank diametre according to DIN 6988040 mmNumber of driven tools12 Speed max.-6000 rpmPower max. (100% DC)10 kWFloor space/WeightDimensions (L x W x H)3,99 x 2,03 x 2,2 mWeight approx.6500 KgTechnologie cycle alternating speedTechnology cycle for the application of an alternating speed for vibration sensitive set-ups (Only in conjunction with Siemens control)Y-Axis PartingTechnology cycle to parting off the workpiece by the Y-axis to ac ...

GeneralIntegrated Mill Turn Center; Control: Control F31iB5 with CELOS CharacteristicsSwing- Ø, max.700 mmMilling spindle upper side1 Bar diametre80 mmSpeed max.4000 rpmMax. Turning Length1530 mmMax machining diameter670 mmDrive power tool spindle5,5/3,7 kWDrive power milling spindle28/23 kWDrive power main spindle18,5/15 kWMovements X / Z200/1542 mmLower Turret10 PositionsNumber of Toolmagazine positions38 Speed max.12000 rpmSlewability of B-Axis±120 degreeMovements X / Z / Y675/1562/300 (±150) mmWeight approx.18500 KgCELOS - ERGOline TouchCELOS - ERGOline Touch to facilitate machine operation incl. 21.5 ERGOline Touch ® control with multi touch screens Uniform management, documentation and visualization of order, process - and machine data Networkable with CAD / CAM User friendly and p(Left Spindle) through-spindle hole dia. 91 mm, 4,000min-1 (STD)(Left Spindle) Through-spindle Hol ...

Specification: Nominal force: 2500 ton Ram stroke: 190 mm Number of strokes in 1 minute: 20 Shut height: 800 mm Bolster plate-to-ram adjustable stroke: 15 Table size: 1250x1400 mm Weight 124.230T

PKZZ 250 Double Column Crank stamping Press Completely overhauled. Electric and Control- Not available. Table 2500 x 1400 mm Ram 2320 x 1250 mm Distance between uprights 2525 mm Window in table width 2300 mm Window in table depth 850 mm Stroke 400 mm Strokes per minute SPM 12 Adjustment of ram 120 mm Shutheight 550 mm Table cushion force 50 to Cushion stroke 160 mm Motor 32 kW Weight ca. 39 tons

; Gross weight [kg]: 12350; Engine: QSK50-G17; Accessories: Battery, Control Panel, Incl. coolant heater and battery charger

; Gross weight [kg]: 16160; Engine: Cummins QSK60-G4; Accessories: Battery, Control Panel, Including heater and battery charger

Kemper vat wagon with boiler Kneading boiler vats for spiral kneader Kemper SP 250 AL Stainless steel boilers with carrying handle for a maximum of 250 kg flour for max. 400 kg dough Dimensions Boiler diameter inside 125 cm Boiler height 60 cm

We offer Peri Pep 30-250 galvanized, used - including original Peri stacking pallet. Special offer 42 x Peri ceiling props including frame = 1.218,00€ 42 pcs PERI Ceiling Prop PEP 30-250, galvanized, used 1 pc. Peri Pallet RP 0.80 x 1.50m galvanized, used The PERI PEP slab props are particularly characterized by their high load-bearing capacity and low weight. Due to a 100% hot-dip galvanizing, the tubular steel ceiling column has a long service life. The risk of injury is significantly reduced by a built-in crush protection of 10 cm. Due to the large adjustment range of 12 cm, frequent replugging is no longer necessary. The high-quality forged nut with hardened contact surface and two-way thread make loosening under full load much easier. All supports are checked and sorted - immediately ready for use. Only while stocks last. Subject to prior sale. If you have  ...

1 used service water pump HABERMANN HPK, power 600 cbm/h, impeller diameter 660, H 33, good condition, E -Motor SONDERMEIER GmbH Type KG315 S/7, 110 kW

We offer you here a used box shelf for sale. The shelf is ideal for lighter boxes, but cardboard boxes can also be easily picked up. The box shelf can be individually adjusted to your own needs. Both the angle of inclination of the roll strips and the distance between planes can be quickly and easily adjusted with an Allen. The levels are provided with guide rails on both sides and a stop on one side, so that the boxes/cardboard boxes are secured against accidental falling. Technical data and further information: Manufacturer: Beewatec Designation: Cardboardrack 1 lanes 19032-01 Year of construction: approx. 2015 Notes: As can be seen in the pictures, the shelf is delivered in a pre-assembled state. Included in delivery are: 01x Box shelf, used Total length: approx. 2,500 mm Total depth: approx. 610 mm Total height: approx. 1,915 mm Internal depth: approx.  ...

Diesel Fuel Tank 2000 Liter, 2.000 Liter Tank, Western Global 20TCC; Gross weight [kg]: 698; Accessories: 2x in stock

GeneralCNC Turning Centre; Control: Control M730UM with CELOS CharacteristicsMax machining diameter406 mmDimensions (L x W x H)3,35 x 2,11 x 2,2 (3,99 x 2,11 x 2,2) mDrive power main spindle22/18,5 kWRapid feed X / Z30/30 m/minMovements X / Z260/795 mmRotary tool spindle speed10000 rpmNumber of tool stations12 Speed max.2500 rpmBar diameter max.102 mmSpindle bore111 mmMax. Turning Length705 mmWeight approx.6400 KgCELOS - ERGOline TouchCELOS - ERGOline Touch to facilitate machine operation incl. 21.5 ERGOline Touch ® control with multi touch screens Uniform management, documentation and visualization of order, process - and machine data Networkable with CAD / CAM User friendly and pLeft Spindle through-spindle hole dia. 111 mm (spindle speed 2,500 min-1, 22/ 18.5 kW)(Left Spindle) Through-Spindle Hole Dia. 111 mm (4.37-inch) (Spindle Speed 2,500 min-1, 22/18.5 kW) The NLX 2500 adopts a h ...

Key data: 200 KW, 250 kVA, 400 V

MODEL: EQ-D250200 ENGINE: Deutz BF6M1015C-LA G1A FREQUENCY (HZ): 50 VOLTAGE (V): 400 MAXIMUM POWER: 250(kVA) / 200(kW) STARTING: ELECTRIC CONTROL SYSTEM: SELF-CONTROL FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 3300kg DIMENSIONS L/W/HEIGHT (MM): 380012502000 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight price, please send us an inqui ...

Complete clean air extraction system with briquette press and piping with gate valves, etc. Extraction system for woodworking companies with briquetting press undermounted. Aspirator ALKO Type: MOBIL-JET 250 Year of construction 2003 Extraction diameter 250 mm Nominal capacity 4900 m³/h Motor power 6.5 KW Dimensions approx. 330 x 135 x 2.95 cm with suction control for automatic slide control. Briquette press WEIMA/ ALKO Type: APC30S Year of manufacture 2007 Motor power 5.5 KW Pressing capacity 30 - 50 kg/h Briquette diameter approx. 50 mm incl. complete piping with branches, bends, valves. there would be another batch of extraction pipes with fittings, which can be purchased cheaply. Plant has been dismantled and packed ready for loading. Condition see pictures, or follow the item description. Parts can also be picked up ...

; Power [PS]: 272; Gross weight [kg]: 2035; Engine: Perkins 1506A-E88TAG2; Accessories: Tanker, Battery, Control Panel, Including : coolant heater and battery charger; Water Tank Volume [l]: 528

USED SIHI ZSKQ 2501 DN90L-2 REFRIGERATED CENTRIFUGAL PUMP

; Power [PS]: 2719; Gross weight [kg]: 13380; Engine: Perkins 4016-61TRG3; Accessories: Battery, Control Panel

; Power [PS]: 272; Gross weight [kg]: 2782; Engine: Perkins 1506A-E88TAG2; Accessories: Tanker, Battery, Control Panel, Stahldach, Including: battery charger and coolant heater; Water Tank Volume [l]: 528

RAANTEC DELTA 250 UV – Converting Year of Manufacture: 2003 ________________________________________ Product Description:  Web width: max. 10 inch – 254mm  1x die-cutting unit  1 x inking unit UV Flexo 1-colour with corona and dust removal  1 set of impression cylinders  Unwinding 850mm  Winding on large roll and small roll possible  Ran all the time only in single-shift operation. Machine Specifications and Equipment: ________________________________________ Accessories Included:  Manuals  Keys  etc. ________________________________________ Technical and Optical Condition: • Technical: 8/10 (checked and in excellent running condition) • Optical: 8/10 (cleaned and ready for immediate end-user deployment) ________________________________________

Key data: 370 mm, 650 mm, 3500 1/min

Machine Details Stock-No. 1105-04067 Type of machine CNC Lathe Make DAEWOO Type PUMA 250 B Year of manufacture 1998 Type of control CNC Storage location HAGUENAU FRANCE Country of origin Corea Delivery time to be agreed Freight basis ex Site Technical details turning diameter 370 mm turning length 648 mm control Fanuc 18 t bar diameter 77 mm swing dia. 570 mm swing diameter over cross slide guide 255 mm max. turning diameter 255 mm drive capacity - spindle motor 18.5/22 kW turning speeds 3500 rpm Turret (X-Stations) 10 pos. JAPAN rapid traverse X-axis 24 m/min total power requirement 32 kW weight of the machine approx. 6 t dimensions of the machine approx. 3.43 X 1.85 X 2 m Additional information GOOD MACHINE WITH CNC FANUC 21 IT 3 JAW CHUCK DIA 250 MM SCHIP CONVoYEUR TOOL SETTER COOLANT INTERLOKED GUARDS

Jib Crane, Column-Mounted Crane, Column Jib Crane, Crane 250 kg, Used Machine Manufacturer: Abus Load Capacity: 250 kg Column Height: 2900 mm Reach: 2600 mm Hoist: Demag, Chain Hoist Type: DKUN 2-250 K V2 Load Capacity: 250 kg Lifting Height: 2600 mm IP Rating: IP 55

Belt round knitter Kemper SBR-2500 Kemper belt round knitter with 2500mm long belts, with flour spreader.Speed adjustable via pot, machine can be moved on rollers, height adjustable. The machine is visually and technically in good condition, can be visited and tested in the warehouse in Bielefeld. We will be happy to send you further pictures and information on request.

Laska Mixer Type ME 250 Vacuum Z Arm Mixer Kneader Filling quantity approx. 180 KG

Laska Mixer ME 250 VAC Capacity 180 Kg Mixing System Z Arm Kneader Mixer

; Gross weight [kg]: 14470; Engine: Caterpillar 3516B; Accessories: Control Panel, Caterpillar 3516B Genset from the official CAT Rebuild Program., Engine is completely rebuild by CAT or even unused/surplus., All other components are usually new., Comes with the standard CAT factory warranty.

IRON SA 25000 ENC sheet metal decoiler was built in 2025 in Italy by Iron Srl. The machine, designed to automate production, has been equipped with state-of-the-art technology, which ensures the highest precision in decoiling coil strip. These include a worm gear reducer with overload clutch, an epicyclical reducer and four self-centring clamps with hydraulic expansion. The machine is controlled by a inverter and feedback encoder, which in turn enables controlled electrical braking. All this is complemented by a sturdy construction made of top-quality steel. The offered IRON 25 t sheet metal uncoiler is brand new and unused. The price also includes a CST coil lift table for easy loading of the coil directly onto the machine arm. The IRON SA 25000 ENC self-centring decoiler is part of the RNM coil strip handling line. The system is customisable and can be equipped with devices such  ...

Stainless steel container, transport container 250 liters Content: 250 Ltr. Working pressure: 0.9 bar, according to type plate, without papers, test pressure 2.0 bar Material: Stainless steel, 1.4301 Design: round, standing, on 4 feet, with welded construction for use by forklift or pallet truck, Outlet with disc valve DN 50, in the upper lid DN 125, 1 x safety valve, 2 x quick coupling connection for CO², Total weight 57 kg last use: Food Height: approx. 1,515 mm Diameter: approx. 625 mm

High-performance flue gas fan very good condition closed wing for high pressure 15kW V-belt transmissions

The generator has never been used before. The device is water-cooled. Further details: see nameplate. Price is negotiable. Shipping possible. The sale is carried out on behalf of the customer. Prior sale and error excepted. The terms and conditions of Cleantec-MR apply.

Suction fan S 250 Motor power 5.5 KW 400V Air capacity 6700m³/h

Backflow preventer, Check valve, Reto Stop, DN 250, PN10, VAG, new -20% Special price ! We still have several identical and other such devices, but the quantity is ending. Buy more than 1 piece there is still a great discount. The current new price of a similar product is € 3,022 excl. If you have a UID number, we will gladly issue an invoice without VAT. As good as new in original packaging! Manufacturer date 2018 The part was purchased from a spare parts warehouse of a company and has never been in operation, is completely as new and in the original packaging. Soft-seated slanted check valve opens already at small differential pressures. Valve disc can be used on both sides, therefore double service life of the valve disc. The one-piece and all-around EPDM rubberized disc allows a completely free passage and reduces the adhesion of impurities. Suitable for both horizonta ...

New KUSING four-sided brush / grinding machine made in Europe. Compact machine with quick adjustment and optional parameters. Technical parameters: Maximum material width: 250 mm Maximum material height: 150 mm Horizontal motor power: 1.5 kW Vertical motor power : 1.1 kW Diameter of the shaft : 40 mm Tool diameter : 200 / 250 mm Minimum possible material length : 250 mm Possible machine versions with 3 spindles KuSING has been manufacturing woodworking machines since 1991. In the field of 4-sided brushing, we offer a wide range of manufactured machines for every application. Parameter changes possible as required. The advertisement was automatically translated. Translation errors are possible.