tba 9 200 used for sale

Pneumatic cylinder, air cylinder, pneumatic stamp, air stamp, standard cylinder -Manufacturer: Atlas Copco, standard cylinder type C4-200 40-200 -Stroke: 194 mm -Piston rod: Ø 40 mm -Total dimensions: 220/265/H645 mm -Total weight: 24 kg

Arburg 520C-2000-675 (154) without funnel General information Item number: 154 Availability: In stock Year of construction: 1998 Brand: Arburg Specifications Spray weight: 240 g Clamping force: 2,000 kN Screw diameter: 45 mm Spray pressure: 2500 bar Spar spacing: 520 x 520 mm Clamping plate size: 715 x 715 mm Tool installation height min.: 250 mm Control: Selogica Language: German Power: 44.9 kW Operating hours: 126766 h Weight: 6630 kg Dimensions: 5.6 x 1.7 m Euromap: Yes Air valve: Yes

grinding diameter: 5 - 255 mm grinding length: 300 mm centre height: 130 mm grinding length at plunge grinding: 50 mm control: SINUMERIK 805 grinding spindle speed: 25 - 1400 U/min work piece spindle speed: 0 - 500 U/min feed of grinding spindle slide cross: 0 - 5000 mm/min table speeds: 0 - 5 m/min grinding wheel diameter: 450 mm total power requirement: 10 kW weight of the machine ca.: 2,3 t dimensions of the machine ca.: 2,65 x 2,2 x 2,35 m Accessories: grinding wheel with flange, 3-jaw chuck, electron. hand wheel The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dry installed radial split volute horizontal centrifugal pump ksb hpk-ls 050-200

Dry installed radial split volute horizontal centrifugal pump ksb hpk-ls 050-200

Gear motor, electric motor, three-phase motor -Speed: 114/228 rpm -Power: 0.8/1 kW -Construction: B3 -Diameter shaft: Ø 24 mm -Protection class: -Number: 1x motors available -Price: per piece -Dimensions: 405/225/H210 mm -Weight: 22.3 kg

Pausch recording workstation Compact CS 2000 with the following device components: Generator Editor Hfe 501 Tube RAD 21 0.6/1.2 Varian Vertical tripod BS 2000 • Before taking over, all devices or systems have been tested on site for their functionality. • The system is located in our warehouse in Freiberg / Germany. It is packed on pallets, professionally railed and with Stretch film wrapped and can be picked up immediately • You buy the system in "ACTUAL" condition from the warehouse Freiberg (EXW), Saxony, Germany, and advance payment. • The sale takes place as "used", EXW Freiberg, Saxony, Germany, to resellers or dealers despite full Functionality without guarantee. • The installation and configuration of the system or plant components must be completed by a specialist authorised by the manufacturer or technicians!

Cutter Kilia 200 liter Express, surface, bowl lid and bowl stainless steel, noise protection lid, loading, ejector, knife shaft brake, knife shaft speed 2-touring

Manufacturer/ Make: SKODA Typ/ Type: W200 Year of construction/ year: 1987 X-way: 11500 mm Y-way/ Y-way: 4500 mm Spindle diameter: 200 mm

Control cabinet, distribution cabinet, control cabinet, TS modular cabinet, profile door -Profile door KTS for: refrigerator -TS single door: 600 x 2000 RAL 7035 -Article No.: 5050154 -Dimensions: 2040/645/H90 mm -Weight: 33 kg

Cutter K+G Wetter CutMix 200 STL with load for 200 liter standard car and ejector, 200 liter cutter, surface, bowl lid with storage wall and bowl stainless steel, noise protection cover, knife shaft brake, main switch, membrane keyboard, infinitely adjustable knife shaft speed (40-4,400 rpm), infinitely adjustable bowl speeds (5-18 rpm), infinitely adjustable mixing gear backwards (40-500 rpm), digital display knife shaft temperature bowl, K+G weather CM 200 STL

Hydraulic cylinder, support cylinder, hydraulic ram, pressure ram, center mower lifting cylinder -Hydraulic cylinder: stroke 200 mm -Piston rod: Ø 23 mm / thread Ø22 x 50 mm -Mounting: Ø20 x 32 mm -Cylinder: outside Ø 62 mm -Dimensions: 770/70/H62 mm -Weight: 7.2 kg

CNC lathe WIA L 200 SY Manufacturer: Hyundai YEAR: 2014 Control Fanuc ... Fanuc 31i Turning diameter ... 550mm Rotation length... 530mm Axis Y ... +-40mm Counter spindle Spindle bore... 70mm Tool turret... 12 L x W x H ... 3045 x 1707 x 2021mm Machine weight ... 4600kg The machine is in good condition, possible to test under power.

Good working conditions

Workbench, work table, assembly bench -Width: 2000mm -Depth: 700mm -Height: 850mm -Drawers: 3 -Storage: 1 -Number of workbenches: 3 available -Price per piece -Weight: 116kg/pcs

An original control cabinet that was dismantled by PAAL Konti 275 C, built in 1994. It is based on SIEMENS S5 controller. It is also suitable for other models such as: Konti 200, 275, 325,425, depending on model and drive power. A complete control cabinet, functional We have several channel balers and balers in our warehouse and we cordially invite you to contact us!

Power resistor, wire potentiometer, resistor, braking resistor, solid tube resistor -Manufacturer: Frizlen, power resistance -Type: FZDPQ 200x35 -Power: 450 W 4.0 ohms -Dimensions: 250/140/100 mm -Weight: 1.7 kg

Clamping angle, clamping aid -Bracket made of: aluminum -Clamping angle for: workpiece clamping -side stop rails -Dimensions: 1155/200/H160 mm -Weight: 22 kg

Hand lever shears, long knife, sheet metal and round steel shears, lever shears -Mubea: sheet metal and round steel shears -Cutting insert length: 200 mm -Dimensions: 380/160/H1240 mm -Weight: 22 kg

An original control cabinet dismantled by PAAL Konti 200B, built in 1987. It is based on analog relays. It is also suitable for the other models such as: Konti 125, 200, 275 , depending on model and drive power. A complete control cabinet, functional

0: 4000,5000 mm Working height: 120 mm 0: ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

0: 3.700mm, 5.100mm, 6.100mm mm Working height: 160 mm 0: ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Sandpaper, emery paper, abrasive cloth, sanding discs, grinding wheels -Theleico: 42A 60-1 I 6 -Outer diameter: 200 mm -Width: 6 mm -Inside diameter: 40 mm -Price: per piece -Number: 19 pieces -Weight: 0.4 kg

pneumatic angle grinder, flex, grinding witch, cut-off grinder, cut-off machine, angle grinder -pneumatic straight screwdriver -Operating pressure: 6 bar -Speed: 900 rpm -Price: per piece -Number: 2 pieces -Dimensions: 380/42/H67 mm -Weight: 1.4 kg/piece

live center, live center point, live Morse taper, live center point, live lathe center, center point, centering taper -Manufacturer: Bokö, live centering tip -Type: 2005 -Recording: MK5 -Dimensions: Ø 85 x 252 mm -Weight: 4 kg

Rubber mat, rubber plate, stop rubber, stop plate, rubber cover, rubber pad -Gum plate: from pre-tensioning technology -Thickness: 48 mm -Width: 150 mm -Length: 200 mm -Number: 12 pieces -Price: per piece -Weight: 4.3 kg/piece

Tool holder, milling holder, milling tool, cutter head, face milling cutter, shell end mill, Side milling cutter -Manufacturer: Wodex, side milling cutter -Adjustment: SK50 -Size: Ø 200 x 12 mm -Dimensions: Ø 200 x 220 mm -Weight: 6.3 kg

Marine diesel piston, diesel engine piston -Piston: Ø 199 mm -Piston height: 265 mm -Piston pin: Ø 75 mm -Distance from center of piston pin to top of piston: 155 mm -Quantity: 2 pieces available -Price: per piece -Weight: 9.025 kg

wire electrode, welding wire, welding wire -Eurotrode: Carbo 2002 -Diameter: 1.00mm -Price: per roll -Number: 3 rolls available -Dimension: O 300/100 mm -Weight per roll: 15 kg

0: 3.700mm, 5.100mm, 6.100mm mm Working height: 160 mm 0: ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding length: max. 630 mm grinding width: max. 200 mm workpiece height: . mm x-axis: max. 250 mm y-axis: max. 710 mm distance spindle center to table: max. 500 mm table surface area: 0,25 mm table load: max. 1,1 t table speed -stepless-: 2 - 18 m/min cross feed autom.: . dust exhaust: 0,25 kW coolant pump: 0,09 kW total power requirement: ca. 4,5 kW weight of the machine ca.: 1,3 t dimensions of the machine ca.: 2400 x 1600 x 1900 mm Adjustments Y axis: 1 scale value = 0.005 mm Z axis: 1 scale value = 0.002 mm Manual adjustment (within the range of 250 mm of the Y axis): 80 mm Speeds: automatic cross feed Adjustment path in Y direction: - intermittent 0.2 - 20 mm per stroke, - continuous: 0 - 4 m/min Grinding wheel Ø max. 200 mm Grinding wheel bore: 51 mm Grinding wheel width: 20 mm Diamond dressing unit Digitaldisplay for 2 advertisement vertical infeed The data for this ad was cr ...

working width: 2000 mm for sheets up to: 3 mm Clear stand width: 2050 mm Stand discharge: 250 mm Support table size: 220 x 2200 mm electr. Drive: 380 V, approx. 5 kW Weight: 2.7 t

Roll Jaws, Floating Center Jaws, Pull-Down Jaws, Machine Vise Jaws -Ground steel jaws: 200 mm -Hole spacing: 140 mm -Price: per piece -Number: 3 pieces -Dimensions: 200/15/H65 mm -Weight: 1.5 kg/piece

New hotbox in the industry standard for max. 200 bar and up to 28 liters per minute. EQUIPMENT - Epoxy coated steel frame with stainless steel cover - 4-wheel chassis with solid rubber tyres - Connection hose 1,5m - Water inlet temperature max. 60° - Heating capacity approx. 90 kW - Water outlet temperature in the steam range up to max. 140°C - With thermal switch and flow monitor Diesel tank: 20L Power supply: 1x 230V Dimensions: (L x W x H): 700mm x 570mm x 800mm Weight: 65kg Shipping possible. Errors and prior sale excepted. We refer to our terms and conditions.

Roll Jaws, Floating Center Jaws, Pull-Down Jaws, Machine Vise Jaws -Steel jaw: 200 mm -Hole spacing: 140 mm/Ø 11 mm -Dimensions: 200/18/H65 mm -Weight: 1.8 kg

Wheel diameter: 200 mm Cutting height: 80 mm cutting width: 180 mm Motor output: 350 W Table dimensions: mm Table tiltable: 45 Grad saw band length: 1400 x 6,5 x 0,35 mm machine weight ab.: 12 kg Dimensions (L/W/H): 700 x 600 x 700 mm Wood band saw with extendable and swiveling saw table The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Special price for stock goods! Only while stocks last! Belt dimensions: 75 x 2000 mm Belt speed: 29 m/sec. Contact disc Ø x W: 200 / 80 mm Face grinding table: 460 x 75 mm Suction connection Ø: 100 mm Motor output power S1 100%: 3.0 kW Motor input power S6 40%: 4.0 kW Voltage: 400 V Length: 1080 mm Width: 440 mm Height: 1000 mm Weight approx.: 66 kg Characteristics: - Good grinding performance due to high belt speed - Quick adjustment for horizontal and inclined position - Continuous face grinding surface for optimal grinding of long workpieces - Constant belt tension due to spring-loaded clamping device - Universally applicable for grinding edges, surfaces and cylindrical grinding - Including quick clamping system for fast belt changes - Easy adjustment of the parallel belt run by means of adjustment screw - Graphite coating on the face grinding surface increa ...

An indestructible machine for the toughest conditions. The machine is suitable for processing raw wood. The machine has no inclination. The saw blade is located directly on the motor. Technical parameters: Maximum saw blade diameter: ø 500/mm Power of the main motor: 5.5 kW Main speed of the saw blade: 2850 rpm Maximum cutting height: 85 mm (with 350 mm saw blade) Inclination of the saw unit: NO Dimensions of the iron table: 1050 × 600 mm Aluminium formatting table: 2000 × 360 mm / OPTION 3200 x 360 mm Formatting table for hardened rods (Altendorf principle) Cutting length: 2000 mm Weight of the machine: 450 kg Given the prices of new Chinese machines that cannot withstand the harsh conditions, this machine is the solution. Made in Slovakia in Europe

Roll jaws, floating central jaws, pull-down jaws, machine vice jaws, clamping jaws -Pull-down jaws: with magnet -Interior dimensions: 140/160 mm -Groove width: 8 mm -Price: per piece -Number: 2 pieces -Dimensions: 200/30/H100 mm -Weight: 3.1 kg/piece

Catalog No. : 5936 Type: W 200 HB Producer: ŠKODA Made in: 1986 Characteristic: Control system: HEIDENHAIN 530 Minimum rotary speed of the spindle: 0.8 1/min Maximum rotary speed of the spindle: 630 1/min X-Axis travels: 16200 mm Y-Axis travels: 5250 mm Z-Axis travels: 1600 mm Taper: ISO 60 Spindle diameter: 200 mm Machine height: 8000 mm Machine length: 20000 mm Machine width: 10000 mm Equipment: Chip convoyer 2008: renovation (new control. wiring and drives)

Roll jaws, floating central jaws, pull-down jaws, machine vice jaws, clamping jaws -1 piece: pull-down jaw -Interior dimensions: 140/160 mm -Groove width: 8 mm -Dimensions: 200/30/H100 mm -Weight: 3.2 kg

SAA 2001 Aspirator Suction nozzle on the device 125mm Suction nozzle on the distributor 100mm Height 2000mm Weight 47kg Motor 1.5kw 230V 50Hz Nominal volume flow 2553 m³/h G&STÜ-5922201

Lifting tipper Kemper HK 200 - Boiler lift tipper from Kemper type HK 200 RD - with stage for WP DK 250 boiler - with enclosure - Height: 366cm - Tilt height 260cm - Year of construction 2014

Pressure booster system, centrifugal pump, water pump, inline pump used 2 pumps Manufacturer: KSB Type ETALINE ETL 150-150-200 GGSAV10D301104 Year of construction 2017 Pump wheel Ø 221 mm Q 2x 209 m³/h at 14.5 m 11 kW Control KSB PumpDrive PDRV2__011K00 Dimensions approx. 2500 x 1200 x 1500 mm All articles are checked for function before delivery, if technically possible! Changes and errors in the technical data, information and prices as well as prior sale reserved.

Pipe sealing cushions, leak sealing cushions, sealing plate, pipe sealing, breakthrough sealing -Pipe sealing cushions -Outer/inner diameter: 200/111 mm -Height: 18 mm -Hole circle: Ø 152/8 mm -Delivery of: steel/stainless steel cover plates possible -Number: 13x pillows available -Price: per piece -Weight: 0.4 kg/piece

three-jaw chuck, three-jaw lathe chuck, 3 jaw chuck -Handover: as is -Chuck size: Ø 200 mm -Bolt circle: Ø 134 mm -Weight: 20.7 kg

I sell a drill with cutting units COMEC FM0V8 2000, built in 1997. Working width max. 2000mm Configuration: 0 motors from below 1+1 motors from sides / angular adjustable 2 motors from behind / head angular adjustable 3 motors from above / head angular adjustable 4 pieces of material prints from above 2 cut saws from above / head angular adjustable Atypical 5-spindle drill heads Including 3 x 15mm / 2 x 25mm. Dubel heads in the price. Very good addition. Available the same.

Description Domino M230i T4 The ability to use stroke lengths of 0 – 360 mm and the auto-stop function to interrupt movement when touching an obstacle make the M230i-T4 label dispenser the most versatile and safe labeling system available on the market today. It is immediately available and ready for use Viewing possible at any time If it does not fit, there is always a large number of different labelers in stock. Talk to us and we will find the right one for you.

Machine type MIG/MAG inverter welding system Böhler brand Type Uranos 2000 SMC Connection voltage 1 x 230 Volt Setting range 5 – 200 amps Duty cycle 35 % ED at 200 amps 60% ED at 160 amps 100% ED at 130 amps Current adjustment infinitely variable Cooling inverter by built-in fan Cooling burner gas-cooled Version portable mounting system Wire feed gearbox 2-roller gearbox Fuse 16 amps Dimensions L x W x H 500 x 210 x 400 mm Special accessories TIG DC welding without HF E-welding, MIG soldering Weight 13 kg Age 6 months Condition workshop tested, as new, incl. UVV test report Scope of delivery welding system with the following accessories: 1 piece welding torch, 3 mtr. long 1 piece ground cable 1 piece pressure reducer argon with 2 pressure gauges 1 roll of welding wire D-200 coil, 5 kg 1 can of non-stick spray 1 piece ...

Siemens AXIOM Iconos R 200 as spare parts dispenser with the following system components: Generator Polydoros SX 65/80_Model No. 8609364 X2217 m. Bedienpult_Model No. 3157554 X2076 Tube Optitop 150/40/80 HC 0,6/1,0, Tiefenblende_Model No. 10092618_Bj. 01/2017 digital image processing Fluorospot Compact_Model No. 7144434 Gerätesteuerpult_Model No. 7030708 G5478 Image intensifier 40 cm_Model No. 3828832 V5092 Handauslöser_Model No. 9722059 G5455 Monitor Simomed HM 44_Model No. 2323464-2_Bj. 2006 Flat screen monitor Acer_Model No. V193 B_Bj. 2009 • The system is located in our warehouse in Freiberg / Germany. It is packed on pallets, professionally lashed and wrapped with stretch film and can be picked up immediately • You buy the system in "ACTUAL" condition from the warehouse Freiberg (EXW), Saxony, Germany, and advance payment. • The sale takes place as "used", EX ...