tailstock used for sale

turning diameter: 325 mm turning length: 532 mm control: FANUC 0i-TD swing over bed: 500 mm spindle turning speed range: 3500 U/min bar capacity: 65 mm travel -x axis: 195 mm travel -z axis: 660 mm spindle drive: 15/11 kW rapid travel - longitudinal/face: 30/30 m/min tailstock quill diameter: 80 mm tailstock quill stroke: 100 mm tailstock quill taper MT: 4 total power requirement: 30 kVA weight of the machine ca.: 4,7 t dimensions of the machine ca.: 2875 x 1675 x 1720 mm Very good condition, low working hours ! Machine comes from a factory closure. CNC control FANUC 0i-TD C axis 12-pos turret with powered positions (3,7/2,2 kW, 5000 rpm) Internal cooling at 17 bar Tailstock Collet chuck up to 60 mm diameter 3-jaw chuck, diameter 250 mm 2 driven tool holders for machining the lateral surface 2 driven tool holders for machining the end face The data for this ad was created with ...

turning diameter: 500 mm centre distance: 1000 mm control: Siemens 840D swing diameter over face slide: 280 mm spindle head: Gr 8 spindle bore: 93 mm spindle diameter in front bearing: 130 mm main drive motor: 25 kW turning speed range: 1 - 3000 U/min tailstock quill taper MT: 5 tailstock quill diameter: 90 mm tailstock travel: 180 mm total power requirement: 34 kVA weight of the machine ca.: 3,2 t dimensions of the machine ca.: 4,4 x 2,2 x 1,97 m - Control unit Siemens 840D - 3-jaw chuck - Support with 2 tool holders ( - steady rest - Tailstock ( air pressure supported ) - chip conveyor - Coolant system only 5720h operating hours very good condition The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

grinding diameter:1000 mm grinding length:6000 mm centre height:510 mm max. workpiece weight:1800 (zw. Spitzen) kg max. workpiece weight:7000 (m. Lünetten) kg grinding spindle speed:400-1200 1/min grinding wheel diameter:915 mm grinding wheel width:100 mm grinding wheel peripheral speeds::35 m/sec cross adjustment:autom. 0,001 mm cross adjustment:mit Handrad: 0,001/0,01/0,1 mm table travel:6200 mm table speed -stepless-:10~4500 mm/min Rotation speed of workhead :3~30 1/min tailstock quill stroke:150 mm taper in tailstock-quill:6 MK tailstock adjustment:über Pneumatik tailstock quill adjustment:manuell spindle drive:30 kW Weight approx.:26 t dimensions:17500x3700x1900 mm surface roughness: max. 0.3µm Ra cylindricity:0.002~0.005 mm/m roundness:0.002~0.005 mm CNC controller:Siemens 828D mit Schleifzyklen fully enclosed:Optional open steady:Optional live center:2 Stk./pc warranty: None pa ...

:Omicron ET6 600 | Omicron ET6 1000 | Omicron ET6 1500 | Omicron ET6 2000 grinding diameter:355 / 455 mm grinding length:630 | 1030 | 1530 | 2030 mm centre height:180 / 230 mm swing over bed:355 / 455 mm max. workpiece weight:250 (300 opt.) kg grinding headstock:. grinding wheel size:450 (opt. 500) mm x127 x min.20-max.80 mm grinding spindle speed:600-1600 (stufenlos) 1/min feed per revolution of handwheel:0,001/ 0,01 / 0,1 mm grinding head swivellable +/-:±180 ° automatic feeds:0,2-3000 mm/min workhead:. workhead - spindle speed:0-600 (stufenlos) 1/min swiveling workpiece drive:±90 ° workhead - center taper:5 MK tailstock:. xx tailstock quill adjustment:35 (opt. 70) mm tailstock quill diameter:48 (opt. 70) mm taper in tailstock:4 (opt. 5) MK table:. table speeds:1-5000 mm/min swivellable angle of table:+9°/-5° | +8°/-4° | +7°/-3° | +6°/-2° ° table adjustment - longitudinal: ...

:Omicron PT6 1000 | Omicron PT6 1500 | Omicron PT6 2000 | Omicron PT6 3000 grinding diameter:595 / 695 mm grinding length:1000 | 1600 | 2100 | 3000 mm centre height:300 / 350 mm Distance between centres:1150 | 1750 | 2250 | 3150 mm swing over bed:595 / 695 mm max. workpiece weight:1200 (1800 opt.) kg grinding headstock:_________________________________________________ __ grinding wheel size:610 mm x 230 x min. 50-max.120 mm grinding spindle speed:600-1250 (stufenlos) 1/min feed per revolution of handwheel:0,001/ 0,01 / 0,1 mm grinding head swivellable +/-:±180 ° grinding spindle movement:480 mm automatic feeds:0,2-3000 mm/min workhead:________________________________________________ __ workhead - spindle speed:0-300 (stufenlos) 1/min swiveling workpiece drive:±90 ° workhead - center taper:6 MK tailstock:__________________________________________________ __ tailstock quill adjustment: ...

:Omicron CNC 3206 | Omicron CNC 3210 grinding diameter:315 mm grinding length:600|1000 mm centre height:160 mm swing over bed:315 mm max. workpiece weight:120 kg grinding headstock:_________________________________________________ __ grinding wheel size:450 x127 x min.20-max.50 mm grinding spindle speed:600-1600 (stufenlos) 1/min feed per revolution of handwheel:0,001/ 0,01 / 0,1 mm grinding head swivellable +/-:±180 ° automatic feeds:0,2-3000 mm/min workhead:________________________________________________ __ workhead - spindle speed:0-600 (stufenlos) 1/min swiveling workpiece drive:±90 ° workhead - center taper:4 MK tailstock:______________________________________________ __ tailstock quill adjustment:50 mm tailstock quill diameter:70 mm taper in tailstock:4 MK table:__________________________________________________ __ table speeds:1-5000 mm/min swivellable angle of table:+9°/-5 ...

:Omicron CNC 3606 | Omicron CNC 3610 | Omicron CNC 3615 | Omicron CNC 3620 grinding diameter:355 / 455 mm grinding length:630 | 1030 | 1530 | 2030 mm centre height:180 / 230 mm swing over bed:355 / 455 mm max. workpiece weight:250 (300 opt.) kg grinding headstock:_________________________________________________ __ grinding wheel size:450 (opt. 500) mm x127 x min.20-max.80 mm grinding spindle speed:600-1600 (stufenlos) 1/min feed per revolution of handwheel:0,001/ 0,01 / 0,1 mm grinding head swivellable +/-:±180 ° automatic feeds:0,2-3000 mm/min workhead:________________________________________________ __ workhead - spindle speed:0-600 (stufenlos) 1/min swiveling workpiece drive:±90 ° workhead - center taper:5 MK tailstock:__________________________________________________ __ tailstock quill adjustment:70 mm tailstock quill diameter:70 mm taper in tailstock:5 MK table:_______________ ...

:Omicron CNC 8030 | Omicron CNC 8040 | Omicron CNC 8050 | Omicron CNC 8060 grinding diameter:795/895/955 mm grinding length:3000|4000|5000|6000 mm centre height:400/450/500 mm Distance between centres:3000|4000|5000|6000 mm swing over bed:795/895/955 mm max. workpiece weight:zw. Spitzen 4 t grinding headstock:_________________________________________________ __ grinding wheel size:760-1200mm x 305 x min. 50-max.120 mm grinding spindle speed:600-1250 (stufenlos) 1/min feed per revolution of handwheel:0,001/ 0,01 / 0,1 mm grinding head swivellable +/-:±180 ° grinding spindle movement:480 mm automatic feeds:0,2-3000 mm/min workhead:________________________________________________ __ workhead - spindle speed:0-150 (stufenlos) 1/min swiveling workpiece drive:±90 ° workhead - center taper:6 MK tailstock:__________________________________________________ __ tailstock quill adjustment:120 mm ...

:Omicron CNC 6010 | Omicron CNC 6015 | Omicron CNC 6020 | Omicron CNC 60300 grinding diameter:595/695 mm grinding length:1000 |1600 |2100 |3000 mm centre height:300/350 mm Distance between centres:1150 |1750 |2250 |3150 mm swing over bed:600/700 mm max. workpiece weight:zw. Spitzen 1200 kg grinding headstock:_________________________________________________ __ grinding wheel size:610mm x 230 x min. 50-max.120 mm grinding spindle speed:600-1250 (stufenlos) 1/min feed per revolution of handwheel:0,001/ 0,01 / 0,1 mm grinding head swivellable +/-:±180 ° grinding spindle movement:480 mm automatic feeds:0,2-3000 mm/min workhead:________________________________________________ __ workhead - spindle speed:0-350 (stufenlos) 1/min swiveling workpiece drive:±90 ° workhead - center taper:6 MK tailstock:__________________________________________________ __ tailstock quill adjustment:70 mm tailst ...

Made in Italy machine according to DIN 8605: lathe with increased accuracy. Tip height: 215 mm Turning diameter over bed: 430 mm Swing over carriage: 240 mm Top width: 1,000 mm Bed width: 290 mm Spindle bore: 52 mm Spindle nose: Camlock 6 " Spindle speeds variable: 6 Spindle speeds: 60-2,000 rpm S6/S1 engine power: 4 kW (option: 5.5 kW) feed Z-axis: (38) 0.05 - 1.88 mm / Rev Feed x axis: (38) 0.02 1,084 mm / Rev Thread cutting, metric: (30) 0.45-20 mm Thread cutting, Witworth: (35) 80-1 3/4 TPI Thread cutting, module: (25) 0.25-10 mm Thread cutting, Diametral Pitch: (30) 160-3 1/2 D.P.. Cross slide Lxw: 370 x 190 mm Transversal carriage stroke: 240 mm Upper carriage Lxw: 275 x 115 mm Upper carriage stroke: 120 mm Tailstock Quill diameter: 60 mm Tailstock Quill stroke: 135 mm Tailstock taper: MK 4 Weight: approx. 2,000 kg Facilities: -Infinitely variable  ...

Horizontal Lathe POREBA TCA 160 x 12 m Condition: very good, complete Technical details: Max. swing over bed 1600 mm Max. swing over carriage 1280 mm Max. swing over gap 1600 mm Turning length (between centers) 12000 mm spindle turning speed (min) 0.85 rpm spindle turning speed (max) 170 rpm The width of guide way 1100 mm Dia. of spindle bore 105 mm Taper of center sleeve 120/80 Feeds: bed slide/longitudinal 0,19-5, 0 mm/1 spindle rotation Feeds cross slide 0,095-2, 5 mm/1 spindle rotation Rapid travel-longitudinal/face 4000 mm/min Max work piece weight centre this centre 30000kg Max work piece weight with 2 steady rest 40000kg Faceplate diameter 1600 mm Metric thread 35 strokes-1-50 mm Whitworth thread 35 strokes-24-1/2 " Module thread Diametrical pitch thread Section of tool shank 70x70mm Travel of the top slide 0,095-2, 5 mm/1 spindle rotation Max.travel o ...

Grinding diameter: 0 mm Grinding length: 0 mm Workpiece weight: 0 kg CNC Brand: 0 CNC Model: 0 Control: GE FANUC Series 16-GC Operating hours: 34900 Technical data Centre height: 175 mm Distance between centres: 1000 mm Workpiece weight on centres max.: 130 kg Grinding weehl left side: Diameter: 400 mm Width: 40 mm Bore: 127 mm Grinding wheel right side: Diameter: 400 mm Width: 63 mm Bore: 127 mm B axis resolution max.: 0.001 ° B axis swivelling range (automatic): 15° + 205 ° Peripheral speed: 35 m/s Max. travel: 275 mm Max. grinding length: 1050 mm Transversal slide: Work piece spindle head: speeds: from: 30 rpm up to: 675 rpm rotatable: 90 ° taper in spindle: MT: 5 Tailstock: Hydraulic return Taper in tailstock:: 3 MT Voltage 50 Hz 3x: 400 Volt Workpiece spindle motor: 7.5 kW Machine´s weight about: 5100 kg Overall dimensions machine: Length: 3750 mm Width: 1200 mm Height: 2 ...

[ 5000 characters max., no information about the advertiser ] Brand:MODUL Model:ZFWZ 2000/3 Type:Gear Hobbers Year:1981 Location:Czech Republic Specification: Max diameter of gear without tailstock 2100 mm Max diameter of gear with tailstock 1450 mm Max face of gear 1060mm Max module with hobbing head 22 Max/ Min center distance 1240/150 mm Min number of teeth 10 Max pressure angel 45 deg Table dia / number of slots 1800 mm/12 Bore in table / length 600/800 mm Max dia of hob / length 300/330 mm Max weight of workpiece 15000 kg Accessories: Standard milling head Tailstock (no clamping) Set of gear supports (shoes) Set of arbors Set of change gears

turning diameter over bed: 460 mm turning diameter over slide rest: 274 mm turning length: 1000 mm spindle bore: 58 mm turning dia. in gap: 690 mm spindle taper: Größe 6, DIN 55029 spindle turning speed - stepless: 30 - 2000 U/min feeds - longitudinal: 0,031 - 1,7 mm/U thread - mm pitch: 0,1 - 14 mm thread - inch: 2 - 112 Gang / inch. tailstock quill diameter: 60 mm tailstock quill taper metric: MT 4 tailstock quill stroke: 120 mm max. workpiece weight between centres: 500 kg voltage: 400 V / 50 Hz spindle motor: 5,5 kW total power requirement: 6 kW weight of the machine ca.: 1,8 t dimensions of the machine ca.: 2,9 x 1,2 x 1,5 m • stepless adjustable turning speed via frequency converter, digital display, 2-axe-DRO, Made:NEWALL The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

max. wheel diameter: 80 mm gear width: 150 mm max. module: 2,5 min. module: total power requirement: 10 kW weight of the machine ca.: 2400 kg M I K R O N (Switzerland) Fully Automatic Gear Hobber for Worm Gears Model A 33 / 1 Year 1985 Ser.-No. 14.06/14.07/14.15 ____________________________________________________________ max. gear- without feed magazine approx. 80 mm max. gear- with feed magazine approx. 50 mm Module max. 2, / 2,5 Axial milling length approx. 150 mm max. workpiece-mounting length approx. 200 mm Milling slide can be swivelled up to 90 degrees Milling cutter - 24 - 50/63 mm Max. radial distance of milling slide 0-14/18 mm Milling cutter adjustment max. 25 mm Milling cutter speed 212 - 2.000 rpm Axial feed range infinitely adjustable 0,05 - 4,0 mm/workpiece rotation radial infinitely adjustable 0,2 - 200 mm/min.  ...

turning diameter: 400 mm turning length: 1000 mm control: FAGOR control: CNC 8055/B-T centre height: 200 mm centre distance: 1000 mm turning dia. over face-slide: 210 mm bed width: 300 mm spindle bore: 65 mm spindle turning speed range: 0 - 3000 U/min transmission ratio: 2 feeds - longitudinal: 0 - 10.000 mm/min feeds - cross: 0 - 10.000 mm/min rapid travel - longitudinal/face: 15 m/min tailstock quill diameter: 68 mm tailstock quill stroke: 155 mm tailstock taper MT: 4 total power requirement: 8 kW weight of the machine ca.: t dimensions: 3,1 x 1,9 x 1,78 m Accessories: 3-jaw chuck, MULTIFIX-tool post with various inserts, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

workpiece length: 6300 mm swing dia.: 800 mm clamping length: 6300 mm grinding diameter: 800 mm grinding length: 1660-6300 mm grinding wheel dia. x width: 1500 x 150 x 650 mm grinding spindle speed: 250 - 500 U/min work piece spindle speed: 0,1-10 / 1 - 15 U/min table - swivable +/-: ° table speeds: m/min max. workpiece weight between centres: 5000 kg grinding motor: 18,5 / 22 kW control: FANUC 31i A5 clamping diameter: 200 - 600 mm diameter of main spindle: 280 mm tailstock quill diameter: 240 mm tailstock adjustment: 90 mm feed in x - axis: 0,01 - 10000 mm/min feed range Z-direction: 1 - 6000 mm/min z-axis: 7750 mm x-axis: 650 mm bed width: 2300 mm bed track: 4 total power requirement: kW weight of the machine ca.: 55 t dimensions of the machine ca.: 16,5 x 5,5 x 2,3 m Namely automatic clamping, automatic gear shifting, automatic slightly loosening, automatic servo indexing, automatic ...

turning diameter over bed: 400 mm turning diameter over slide rest: 235 mm turning length: 1000 mm turning dia. in gap: 560 mm spindle bore: 52 mm spindle taper: Größe 6, DIN 55029 spindle turning speed - stepless: 18 - 2120 U/min feeds - longitudinal: 0,015 - 0,6 mm/U face feeds: 0,0075 - 0,3 thread - mm pitch: 0.25 - 7,5 mm thread - inch: 4 - 120 Gang / inch. tailstock quill diameter: 50 mm tailstock quill taper metric: MT 4 tailstock quill stroke: 120 mm max. workpiece weight between centres: 500 kg voltage: 400 V / 50 Hz spindle motor: 5,5 kW total power requirement: 7,5 kW weight of the machine ca.: 1,85 t dimensions of the machine ca.: 2,9 x 1,2 x 1,5 m • stepless adjustable turning speed via frequency converter, digital display, 2-axe-DRO, Made:NEWALL The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Grinding diameter: 0 mm Grinding length: 0 mm Workpiece weight: 0 kg CNC Brand: 0 CNC Model: 0 Control: GE FANUC Series 18-T Technical data Centre height: 175 mm Distance between centres: 1000 mm Max. grinding diameter: 348 mm Grinding length: 1000 mm Workpiece weight on centres max.: 250 kg Grinding wheel: Diameter: 500 mm Width: 100 mm Peripheral speed: 45 m/s Longitudinal slide: Max. travel: 1400 mm Resolution: 0.0001 mm Feed speed up: 8000 mm/min Transversal slide: Max. travel: 340 mm Resolution: 0.0001 mm Feed speed up: 8000 mm/min Swivelling range: +9/-9 ° Work piece spindle head: speeds: from: 20 rpm up to: 1000 rpm rotatable: +30/-45 ° Précision d´usinage: 0.0005 mm taper in spindle: MT: 6 Tailstock: Taper in tailstock:: 4 MT Tailstock travel of barrel: 50 mm Voltage 50 Hz 3x: 400 Volt Grinding spindle motor: 15 kW Total power required: 26.5 kW Total power requi ...

turning diameter over bed: 560 mm turning diameter over slide rest: 355 mm turning length: 2000 mm turning diameter in the gap: 790 mm turning speeds: 20 - 1800 U/min centre height: 380 mm spindle bore: 80 mm tailstock quill taper MT: 2,8 MK tailstock travel: 150 mm tailstock quill diameter: 75 mm total power requirement: 5,5 kW weight of the machine ca.: 3,4 t dimensions of the machine ca.: 3,5 x 1,15 x 1,3 m • 80 mm spindle passage • Gears hardened and ground • manual central lubrication • adjustable main spindle bearings • Overload clutch in the lock case • bed bridge • incl. 3 - axis digital display The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

centre distance: 8500 mm turning diameter over bed: 1070 mm turning diameter over slide rest: 800 mm spindle bore: 128 mm turning speeds: 1,12 - 1120 U/min Control: Alan Bradley 9-series total power requirement: 62 kW weight of the machine ca.: t dimensions of the machine ca.: m 3 Shear Bed, Carriage can bypass Steady Rest and Tailstock 6-position Sauter Turret 360 mm Capacity Self Centering Hydraulic Steady Rest 385 mm Capacity Rotaring Work Support (Used for Gun Barrels) 800 mm 4-Jaw Chuck Tailstock Quill diameter Ø 200 mm Tailstock Taper M.T. 6 Chip Conveyor The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

- Sino SDS6-3V 3-axis position display - magnetic and manual spindle brake - 3 jaw chucks ø 250 mm - 4 jaw linings ø 320 mm - Stop Z-axis - fixed & running bezels - Multifix Type C incl. 4 holders - Flat disc ø 430 mm - Lighting system - Coolant sealing Specification - Tip width: 2000 mm - Circulating Ø over bed: 600 mm - Circulation Ø over slide: 360 mm - Circulating Ø in eruption: 730 mm - Bed width: 330 mm - Spindle bore Ø: 80 mm - Spindle cone: Metric 80 C8 / D1 - D8 - Speed range: 24 - 1600 rpm - Speed levels: 15 - Metric threads: 0.5 - 28 mm (66 steps) - Inch thread: 1 - 56 tpi (66 steps) - Module thread: 0.5 - 3.5 mm (33 steps) - Thread with diametrical slope: 8 - 56 dp (33 steps) - Longitudinal feed: 0.072 - 4.038 mm/U (66 steps) - Transverse feed: 0.036 - 2.019 mm/U (66 steps) - Tool holder: 25 x 25 mm - Tailstock Pinole Ø: 65 mm - Tailstock ...

Grinding diameter: 0 mm Grinding length: 0 mm Workpiece weight: 0 kg CNC Brand: 0 CNC Model: 0 Control: KELCO 90 Technical data Centre height: 225 / 305 mm Distance between centres: 1000 mm Travels: Z axis: 1160 mm X axis: 350 mm Workpiece weight on centres max.: 200 kg Diameter: 449 mm Grinding weehl left side: Diameter: 500 mm Width: 80 mm Bore: 203 mm Grinding wheel right side: Diameter: 400 mm Width: 40 mm Bore: 127 mm B axis swivelling range: +30 / -190 ° Grinding wheel speeds: up to: 1720 rpm Peripheral speed: 45 m/s Rotatable grinding spindle head (b-axis): 270 ° Work piece spindle head: speeds: stepless from: 5 rpm up to: 500 rpm rotatable: -10 / +100 ° taper in spindle: MT: 5 Tailstock: con regolazione micrometrica Taper in tailstock:: 4 MT Tailstock travel of barrel: 50 mm Feeds: X axis: 8 m/min Resolution: 0.1 µm Z axis: 16 m/min Resolution: 0.2 µm Max. table angular di ...

Grinding diameter: 0 mm Grinding length: 0 mm Workpiece weight: 0 kg CNC Brand: 0 CNC Model: 0 Control: FANUC Series 0i-TD Operating hours: 12835 Technical data Centre height: 175 mm Distance between centres: 1000 mm Travels: Z axis: 1150 mm X axis: 370 mm Workpiece weight on centres max.: 150 kg Grinding wheel: Diameter: 500 mm Width: 63 mm Bore: 203 mm Peripheral speed: 50 m/s Rotatable grinding spindle head (b-axis): 0 / 30 ° Work piece spindle head: speeds: stepless from: 1 rpm up to: 1000 rpm C axis taper in spindle: ISO: 50 Required power: 4 kW Tailstock: con regolazione micrometrica Hydraulic return Taper in tailstock:: 4 MT Tailstock travel of barrel: 60 mm Feeds: Air connect: 5 - 7 bar Voltage 50 Hz 3x: 400 Volt Grinding spindle motor: 7.5 kW Total power required: 20 kVA Machine´s weight about: 10500 kg Overall dimensions machine: Length: 3900 mm Width: 2584 mm Height: 2 ...

Grinding diameter: 0 mm Grinding length: 0 mm Workpiece weight: 0 kg CNC Brand: 0 CNC Model: 0 Control: GE FANUC Series 18i-T Operating hours: 0 Technical data Centre height: 125 mm Distance between centres: 760 mm Grinding length: 430 mm Workpiece weight on centres max.: 100 kg Grinding wheel:: Standard Diameter: 400 mm Width: 63 mm Bore: 127 mm Rotatable grinding spindle head (b-axis) Indexing manually: 2.5° Longitudinal slide:: Z Max. travel: 650 mm Resolution: 0.0001 mm Feed speed up: 0.1 mm/min Feed range: 12000 mm/min Transversal slide:: X Max. travel: 320 mm Resolution: 0.0001 mm Feed speed up: 0.1 mm/min Feed range: 6000 mm/min Work piece spindle head: from: 8 rpm up to: 800 rpm taper in spindle: MT: 5 Tailstock: Taper in tailstock:: 4 MT Tailstock travel of barrel: 50 mm Table speed: Rapid motion: 12 / 6 m/min Voltage 50 Hz 3x: 400 Volt Grinding spindle motor: 7.5 ...

- Sino SDS6-3V 3-axis position display - magnetic and manual spindle brake - 3 jaw chucks ø 250 mm - 4 jaw linings ø 320 mm - Stop Z-axis - fixed & running bezels - Multifix Type C incl. 4 holders - Face disc - Lighting system - Coolant sealing Specification - Center width: 1000 mm - Circulating Ø over bed: 500 mm - Circulation Ø over slide: 325 mm - Orbital Ø in eruption: 630 mm - Bed width: 330 mm - Spindle bore Ø: 80 mm - Spindle cone: Metric 80 C8 / D1 - D8 - Speed range: 24 - 1600 rpm - Speed levels: 15 - Metric threads: 0.5 - 28 mm (66 steps) - Inch thread: 1 - 56 tpi (66 steps) - Module thread: 0.5 - 3.5 mm (33 steps) - Thread with diametrical slope: 8 - 56 dp (33 steps) - Longitudinal feed: 0.072 - 4.038 mm/rev (66 steps) - Transverse feed: 0.036 - 2.019 mm/rev (66 steps) - Tool holder: 25 x 25 mm - Tailstock Pinole Ø: 65 mm - Tailstock pinole ...

Working area Swing over bed: 650 mm Swing over cross slides: ? 465 mm Max. turning diameter: ? 400 / ? 315 mm Cross travel (X): 267.5 mm Longitudinal travel (Z): 600 mm Rapid traverse (X / Z): 30 / 30 m/min Main Spindle Spindle nose: A2-8 Bar capacity: ? 80 mm Spindle diameter in the front bearing: 130 mm Chuck: 210 / 250 / 315 Drive power (40/100% ED): 25.5 / 17 kW Maximum torque (40/100% ED): 426 / 283 Nm Maximum speed: 4000 rpm Positioning accuracy Acc. to ISO 230-2 in X- / Z-axes (indirect measurement system): 5 / 10 ?m Acc. to ISO 230-2 for C-axis: 20 arcsec Turret Number of tool stations: 12 x VDI 40/6 x BT Of which driven tool stations: 12 Tool station diameter: 40 mm Max. power: 5.44 kW Max. torque (40 % DC): 20 Nm Max. speed: 4,000 rpm Tailstock Tailstock travel: 500 mm Life center interface: 5 MK Max. tailstock force: 8 kN Guidwa ...

Working area Swing over bed: 650 mm Swing over cross slides: ? 465 mm Max. turning diameter: ? 400 / ? 315 mm Cross travel (X): 267.5 mm Longitudinal travel (Z): 600 mm Rapid traverse (X / Z): 30 / 30 m/min Main Spindle Spindle nose: A2-8 Bar capacity: ? 80 mm Spindle diameter in the front bearing: 130 mm Chuck: 210 / 250 / 315 Drive power (40/100% ED): 25.5 / 17 kW Maximum torque (40/100% ED): 426 / 283 Nm Maximum speed: 4000 rpm Positioning accuracy Acc. to ISO 230-2 in X- / Z-axes (indirect measurement system): 5 / 10 ?m Acc. to ISO 230-2 for C-axis: 20 arcsec Turret Number of tool stations: 12 x VDI 40/6 x BT Of which driven tool stations: 12 Tool station diameter: 40 mm Max. power: 5.44 kW Max. torque (40 % DC): 20 Nm Max. speed: 4,000 rpm Tailstock Tailstock travel: 500 mm Life center interface: 5 MK Max. tailstock force: 8 kN Guidwa ...

Working area Swing over bed: 650 mm Swing over cross slides: ? 465 mm Max. turning diameter: ? 400 / ? 315 mm Cross travel (X): 267.5 mm Longitudinal travel (Z): 600 mm Rapid traverse (X / Z): 30 / 30 m/min Main Spindle Spindle nose: A2-8 Bar capacity: ? 80 mm Spindle diameter in the front bearing: 130 mm Chuck: 210 / 250 / 315 Drive power (40/100% ED): 25.5 / 17 kW Maximum torque (40/100% ED): 426 / 283 Nm Maximum speed: 4000 rpm Positioning accuracy Acc. to ISO 230-2 in X- / Z-axes (indirect measurement system): 5 / 10 ?m Acc. to ISO 230-2 for C-axis: 20 arcsec Turret Number of tool stations: 12 x VDI 40/6 x BT Of which driven tool stations: 12 Tool station diameter: 40 mm Max. power: 5.44 kW Max. torque (40 % DC): 20 Nm Max. speed: 4,000 rpm Tailstock Tailstock travel: 500 mm Life center interface: 5 MK Max. tailstock force: 8 kN Guidwa ...

Working area Swing over bed: 650 mm Swing over cross slides: ? 465 mm Max. turning diameter: ? 400 / ? 315 mm Cross travel (X): 267.5 mm Longitudinal travel (Z): 600 mm Rapid traverse (X / Z): 30 / 30 m/min Main Spindle Spindle nose: A2-8 Bar capacity: ? 80 mm Spindle diameter in the front bearing: 130 mm Chuck: 210 / 250 / 315 Drive power (40/100% ED): 25.5 / 17 kW Maximum torque (40/100% ED): 426 / 283 Nm Maximum speed: 4000 rpm Positioning accuracy Acc. to ISO 230-2 in X- / Z-axes (indirect measurement system): 5 / 10 ?m Acc. to ISO 230-2 for C-axis: 20 arcsec Turret Number of tool stations: 12 x VDI 40/6 x BT Of which driven tool stations: 12 Tool station diameter: 40 mm Max. power: 5.44 kW Max. torque (40 % DC): 20 Nm Max. speed: 4,000 rpm Tailstock Tailstock travel: 500 mm Life center interface: 5 MK Max. tailstock force: 8 kN Guidwa ...

General- Compound slides with turning/milling spindle as integrated spindle motor, with hydr. locking at turning acceptance HSK-63A DIN 69893 - Y-axis ± 100 mm - B-axis ±110° with pneumatic locking - Tools magazin disc with 1x24 positions - Absolute direct gauging system in the X, Y, Z linear axes - Coolant pump 5 bar; 20l/min - Cooling system for spindle motor, turning/milling spindle, B-axis torque motor - USB interface, Ethernet interface; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways500 mmTurning diameter500 mmMax. Turning Length750 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmMain drive 1Drive power (100% DC)25 kWDrive power (40% DC)32 kWSpeed range- 5000 rpmTorque (100% DC)280 NmMax. torque (40% DC)360 NmC-Axis Speed-5000 rp ...

: neu : ca. 6 Monate ab Auftragse : Bulgarien : 78300 € : 1566 € : 760 mm : 3000 mm : 380 mm : 132 mm : 520 mm : 560 mm : 11 : 140 M : 3 : 7 - 42, 28 - 170, 165 - 1 U/Min : 150 : 0.039 mm/U : 0.02 mm/U : 0.5 - 180 mm : 60 - 1/6 Gänge/ : 0.125 - 45 : 2 - 240 : 410 mm : 150 mm : 105 mm : 6 MK : 225 mm : 15 kW : 4470 kg driven by variable speed control (3 steps) 3-axes digital readout FAGOR with CSS (constant surface speed) quick change toolpostAmestra type Multifix with 4 holders (3 square, 1 round) 3-jaw chuck Bison3295/DIN6350, Ø 400 mm spindle dead center main motor with frequency invertor four way rapid traverse device foot pedal brake longitudinal stop for 1 position steady and following rest coolant equipment full length rear splash guard leadscrew and shaft protection safety guard for the chuck toolholder guard levelling bolts and plates quick release tailstock tailstock quill ...

Lathe Seiger SLZ 500E Year of construction: 2001 Technical Details Turning length: 2000 mm control: Cycle control Heidenhain Manual Plus total power requirement: 25 kW Machine weight approx.: 3 t Swing diameter over bed: 500 mm Swing diameter max. via face slide: 280 mm bed width: 350 mm spindle head according to DIN 55027 size 8 spindle bore: Ø mm 93 / 130 (option) spindle Ø in front bearing mm: 130 / 170 (option) tailstock quill Ø mm 90 tailstock stroke mm: 180 tailstock Morse taper: MK 5 Video: https://youtu.be/_YocZ_jHsyQ https://www.youtube.com/watch?v=4PBiyhvmj7I

Key data: 500 mm, 200 mm

JANUS HTC2050 CNC lathe was built in Poland in 2010. The machine, characterised by high stability and operational reliability, uses the necessary equipment for high-speed and finishing machining, allowing for precise machining of internal holes, columns, cones, arches and all types of screw threads. The machine uses a high-speed spindle with infinitely variable rotation speed from 40 to 4000 rpm and a bed inclined by 45°, which facilitates chip removal and increases the cutting force transmitted by the horizontal bed and its head. Rear and front spindle angular contact bearings simultaneously transfer radial and axial loads, ensuring low spindle temperature rise and less thermal deformation during high-speed finishing. The JANUS lathe equipment includes a state-of-the-art FANUC Series 0i Mate-TC CNC controller, a chip conveyor and the tools shown in the photos. The total weight of th ...

turning diameter: max. 820 mm turning length: max. 790 mm control: MSC 516 turning diameter over bed: 890 mm turning diameter over cross slideways: 560 mm centre distance: 900 mm Main spindle:: turning speed range - main spindle: 4 - 1.800 min/-1 power capacity - main spindel: 37 / 30 kW max. Torque: 3.870 Nm Number of speed ranges: 3 spindle bearing diameter: 170 mm spindle bore: 105 mm max. usable bar diameter: 89 mm spindle head: JIS A1-11 turret:: number of toolpositions: 12 pos. Shank height for square tool: 32 mm Drill shank diameter: max. 65 mm axis stroke:: x-axis: 435 (25 + 410) mm z-axis: 860 mm Tailstock:: tailstock: 680 mm diameter of quill: 110 mm quill stroke: 100 mm taper of center: MK 4 feeds:: rapid traverse: X: 5 / Z: 8 m/min Tipp feed: 0 - 1.260 mm/min total power requirement: 62 kVA weight of the machine ca.: 9,2 t dimensions of the machine ca.: 6,5 x 3,0 x 2,6 m ...

turning diameter: 640 mm turning length: 1500 mm control: SIEMENS SINUMERIK 820 D turning diameter over slide: 420 mm spindle bore: 65 mm centre height: 320 mm centre distance: 1500 mm bed width: 440 mm spindle drive: 17 kW max. torque on the spindle: max. 162 Nm rapid travel - longitudinal/face: 10 / 5 m/min feed power: 10000 / 9500 N tailstock quill diameter: 100 mm tailstock quill stroke: 240 mm tailstock taper MT: 5 total power requirement: 25 kW weight of the machine ca.: 5,5 t Accessories: 3-jaw chuck 310 mmø, various tool holders for turret, running center, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 600 mm, 1250 mm, 3000 1/min

Machine Details Stock-No. 1105-03939 Type of machine CNC Lathe - Inclined Bed Type Make GILDEMEISTER DMG Type NEF 600 Year of manufacture 2006 Type of control CNC Storage location HAGUENAU FRANCE Country of origin Germany Delivery time immediately Freight basis EX WORK Price Technical details turning diameter 600 mm turning length 1250 mm control SIEMENS 840 D greates pass round over bed 600 mm centre height 350 mm Spindle Bore 92 mm turning speed range 3500 rpm Rapid Travel - Longitudinal/Face 20 m/min face stroke 400 mm tailstock quill diameter 100 mm Tailstock Quill Stroke 1150 mm tailstock taper MT 5 Turret (X-Stations) 12 turning diameter over slide 410 mm Additional information Acc. 3-Jaw Chuck 315 mm, tailstok turret 8 P ,chip conveyor, coolant CNC Siemens 840 D

turning diameter: max. 650 mm turning length: max. 790 mm control: MORIC T5F turning diameter over bed: 890 mm turning diameter over cross slideways: 560 mm centre distance: 900 mm Main spindle:: turning speed range - main spindle: 4 - 1.010 min/-1 power capacity - main spindel: 37 / 30 kW max. Torque: 3.870 Nm Number of speed ranges: 2 spindle bearing diameter: 240 mm spindle bore: 168 mm max. bar capacity: 144 mm usable bar diameter: 120 mm spindle head: JIS A2 -11 chucking diameter: 610 mm turret:: number of toolpositions: 12 pos. Shank height for square tool: 32 mm Drill shank diameter: max. 65 mm axis stroke:: x-axis: 350 (25 + 325) mm z-axis: 860 mm Tailstock:: tailstock: 680 mm diameter of quill: 110 mm quill stroke: 100 mm taper of center: MK 4 feeds:: rapid traverse: X: 5 / Z: 8 m/min Tipp feed: 0 - 1.260 mm/min total power requirement: 69 kVA weight of the machine ca.: 9,2 ...

turning diameter: 500 mm turning length: 1000 mm control: MONFORTS CONTROL control: SYSTEM MTC-K turning diameter over bed slide: 290 mm spindle bore: 70 mm spindle turning speed range: 3 - 2800 U/min spindle power: 15 kW max. torque on the spindle: 1530 Nm spindle head: DIN 55027 Gr. 8 feed power X/Z axis: 11300 N rapid travel - longitudinal/face: 10 / 5 m/min bed width: 360 mm travel of cross-slide: 265 mm upper slide travel: 140 mm turning tool - shaft cross cut: 32 x 25 mm tailstock quill diameter: 80 mm tailstock quill stroke: 160 mm tailstock taper MT: 5 total power requirement: kW weight of the machine ca.: 3,1 t dimensions of machine L x W x H: 2,88 x 1,68 x 2,18 m Accessories: 3-jaw chuck ROTA-S plus 250 mmø, 4 pos. toolholder PARAT, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 500 mm turning length: 1500 mm control: MONFORTS CONTROL control: SYSTEM EURO TURN turning diameter over bed slide: 290 mm spindle bore: 70 mm spindle turning speed range: 3 - 2800 U/min spindle power: 15 kW max. torque on the spindle: 1530 Nm spindle head: DIN 55027 Gr. 8 feed power X/Z axis: 11300 N rapid travel - longitudinal/face: 10 / 5 m/min bed width: 360 mm travel of cross-slide: 265 mm upper slide travel: 140 mm turning tool - shaft cross cut: 32 x 25 mm tailstock quill diameter: 80 mm tailstock quill stroke: 160 mm tailstock taper MT: 5 total power requirement: kW weight of the machine ca.: 3,3 t dimensions of machine L x W x H: 3,45 x 1,65 x 1,93 m Accessories: 3-jaw chuck ROTA-S plus 250 mmø, 4 pos. toolholder PARAT, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

PONAR KOWARY NUA 25 tool grinding machine was built by the Polish company PONAR KOWARY (LAKFAM) in 1984. A machine characterised by a robust construction of high stability, is used in tool shops and workshops for precision grinding of tools and tooling. Grinding of workpieces is performed on a table with a surface area (L x W) of 915 x 135 mm with two handwheels for manual longitudinal movement (X axis) and transverse movement (Z axis) of the work table. The reliable grinding wheel spindle moving at 3850 and 5635 rpm guarantees rapid and precise machining. The total weight of the machine is 910 kg. The machine is offered with the extensive range of equipment shown in the attached photos, which includes: – driven divider to the instrument along the screw line – angle vice 2 pcs. – moving tailstock: 2 pcs. – 3-jaw chuck fi 160 + spanner – workpiece centre positioning tool ...

GeneralTurning Center; Control: Control M730UM CharacteristicsMax machining diameter366 mmDimensions (L x W x H)3,84 x 2,36 x 1,80 mDrive power tool spindle7,5/5,3/3,7 kWDrive power main spindle22/11 kWRapid feed X / Z30/30 m/minInput precision of C-axis on Mainspindle0,001 degreeMovements X / Z250/1143 mmRotary tool spindle speed6000 rpmNumber of tool stations12 Speed max.4500 rpmBar diameter max.65 mmSpindle bore73 mmSwing- Ø, max.760 mmMax. Turning Length1085 mmWeight approx.6500 KgSLIMlineSLIMline DMG MORI operating system equipped with MAPPS. The large 15-inch display can reduce the number of switching of the screen as it provides the four-way split screen and allows user to see more information at once. It is also possible to customi(Spindle 1) 22/15/11 kW,4,500 min-1 (Standard)(Spindle 1) Standard Spindle 22/15/11 kW (30/20/15 HP), 4,500 min-1 The ALX2000 adopts a highly reliable ...

GeneralMilling Specification; Control: Control M730UM with CELOS CharacteristicsMax machining diameter278 mmDimensions (L x W x H)2,82 x 2,09 x 2,15 mDrive power tool spindle5,5/5,5/3,7 kWDrive power main spindle11/15/15 kWRapid feed X / Z30/30 m/minInput precision of C-axis on Mainspindle0,001 degreeMovements X / Z260/590 mmRotary tool spindle speed10000 rpmNumber of tool stations12 Speed max.6000 rpmBar diameter max.52 mmSwing- Ø, max.755 mmMax. Turning Length192 mmWeight approx.4900 KgCELOS - ERGOline TouchCELOS - ERGOline Touch to facilitate machine operation incl. 21.5 ERGOline Touch ® control with multi touch screens Uniform management, documentation and visualization of order, process - and machine data Networkable with CAD / CAM User friendly and pHigh-output spindle (Left Spindle) 15/ 11 kW, 6,000 min-1(Left Spindle) High-Output Spindle 15/11 kW (20/15 HP), 6,000 min-1 The NLX ...

GeneralCNC Turning Centre with C axis and tool drive; Control: Control M730UM with CELOS CharacteristicsMax machining diameter356 mmDimensions (L x W x H)2,82 x 2,09 x 2,15 mDrive power tool spindle5,5/5,5/3,7 kWDrive power main spindle15/22/22 kWRapid feed X / Z30/30 m/minInput precision of C-axis on Mainspindle0,001 degreeMovements X / Z260/590 mmRotary tool spindle speed10000 rpmNumber of tool stations12 Speed max.-5000 rpmBar diameter max.65 mmSwing- Ø, max.755 mmMax. Turning Length510 mmWeight approx.5000 KgCELOS - ERGOline TouchCELOS - ERGOline Touch to facilitate machine operation incl. 21.5 ERGOline Touch ® control with multi touch screens Uniform management, documentation and visualization of order, process - and machine data Networkable with CAD / CAM User friendly and pHigh-output spindle (spindle 1) 22/ 15 kW, 5,000 min-1The NLX 2000 adopts a highly reliable main spindle de ...

General2-Axes Universal Turning Center with driven tools, C-axis, Y-axis and counter spindle - Direct measuring system for X / Y axis; Control: DMG MORI SLIMline® Multi-Touch control Working areaSwing diameter over transverse guideway370 mmSwing diameter over guide ways700 mmTurning diameter400 mmBar diameter max.80 mmSlide 1Transverse stroke276 mmLongitudinal stroke755 mmY axis, vertical+/- 60 mmRapid traverse in X30 m/minRapid traverse in Z30 m/minRapid traverse in Y22,5 m/minMain drive 1Drive power (100% DC)17 kWDrive power (40% DC)25,5 kWSpeed range- 4000 rpmTorque (100% DC)283 NmMax. torque (40% DC)426 NmC-Axis Speed-200 rpmTorque of C-Axis (holding torque)426 NmWork spindle (left)Spindle noseA2-8 Bar diametre80 mmSpindle diametre on front bearing130 mmMain drive 2Drive power (100% DC)13 kWDrive power (40% DC)14 kWSpeed range- 5000 rpmTorque (100% DC)171 NmMax. torque (40% DC)192 N ...

GeneralTurning-milling centre; Control: Fanuc 31iB5 CharacteristicsSwing- Ø, max.1070 mmDrive power milling spindle22 kWDrive power second spindle22 kWDrive power main spindle22 kWNumber of Toolmagazine positions50 Speed max.8000 rpmSlewability of B-Axis1 degreeMovements X / Z / Y1040/+-330/3150 mmMilling spindle upper side1 Input precision of C-axis on Counterspindle0,0001 degreeBar diametre164 mmSpindle speed 2nd Spindle max.1500 rpmInput precision of C-axis on Mainspindle0,0001 degreeBar diametre164 mmSpeed max.1500 rpmMax. Turning Length3076 mmMax machining diameter1070 mmWeight approx.46000 KgTool spindle full indexing specificationsErhöhung der mögl. Indexierung der B-Achse auf 0,0001º Einrichtung zur Positionierung der B-Achse mit einem minimalen Winkel von 0,0001º anstelle der Standardausführung mit 1º, einschließlich der Option Direktes Wegmesssystem in der B-Achse derSp ...

turning diameter over bed: 500 mm turning diameter over slide rest: 320 mm turning length: 1000 mm centre height: 250 mm centre distance: 1000 mm spindle bore: 56 mm spindle turning speed range: 14 - 2240 U/min spindle nose: DIN 55027 Gr. 6 feeds - longitudinal: 0,023 - 4,8 mm/U feeds - cross: 0,011 - 2,4 mm/U face slide travel: 300 mm upper slide travel: 140 mm thread - mm pitch: 0,25 - 60 mm thread - inch: 120 - 1/2 Gg/ thread - module: 0,125 - 15 mm tailstock quill diameter: 80 mm tailstock quill stroke: 180 mm tailstock taper MT: 5 total power requirement: 7,5 kW weight of the machine ca.: t dimensions of machine L x W x H: 2,42 x 1,23 x 1,93 mm Accessories: 3-jaw chuck 250 mmø, MULTIFIX-toolpost with various inserts, drill chuck, running center, coolant The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

turning diameter: 820 mm turning length: 300 mm turning diameter over slide: 465 mm control: max. torque on the spindle: 3000 Nm turning speeds: 5,6-1120 U/min Feed: 1-5000 mm/min Rapid movement: 5000 mm/min tailstock quill taper MT: 6 3 jaw chuck Forckrath: mm steady: mm main drive motor: 50 kW diameter of main spindle: 170 mm spindle passage: 128 mm tailstock quill diameter: 125 mm tailstock quill stroke: 250 mm z-axis: 3000 mm x-axis: 550 mm total power requirement: 52 kW weight of the machine ca.: 7,1 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Dividing head, dividing head, dividing table, with tailstock WMW Type TU 100 ( TU100 ) Center height: 105 mm Dividing head: Mount: MK4 ( inside ) / cone Ø 51 / 54 mm x 10 mm ( outside ) Flange diameter: Ø 108 mm, bolt circle diameter: 75 mm 3x threaded hole: M10 x 1.5, Depth: 20 mm -15° - +105° tiltable spindle bore: Ø 24 mm Base: 105 x 195 mm tailstock with quill and fixed grain tip Tool holder: MK2 quill stroke: 35 mm quill: +/- 5° tiltable foot: 70 x 142 mm used, checked! Dimensions ( dividing head ): 480 x 450 x 260 mm Dimensions (tailstock) ): 220 x 70 x 115 mm

Dividing head, dividing head, dividing table, with tailstock TOS KURIM Type DU200AN Center height: 105 mm Dividing head: Receptacle: Inner diameter: Ø 48 mm, depth: 50 mm -10° - +100° tiltable spindle bore: Ø 22 mm Base: 155 x 215 mm tailstock with quill and fixed grain tip Tool holder: MK3 quill stroke: 40 mm quill: +/- 5° tiltable foot: 100 x 140 mm used, tested ! Dimensions ( dividing head ): 400 x 395 x 230 mm Dimensions (tailstock) ): 242 x 100 x 125 mm