135,973 used machines on RESALE, but how to find them? Machine Search
Müro A4/5000 block size press; good condition; cleaned and tested; Heat baffle; Stack increase; optionally with dryer. Block gluing machine Müro A4/5000; good condition; cleaned and checked; pile elevation; heating sheet; for option with heater.
blowers Müro block glue presses; Condition used; 2 pcs.; 1x old connector, 1x new connector; cleaned and checked for function. Heater Müro padding press; condition used; two pic.; one old connector, one with new connector; cleaned and checked on function.
used baler Manufacturer: ABBA Type: ACOMAT 400 H3A Year of Make: 2008 specifications: Press force: 45 t Drive power: 7.5 kW Throughput capacity: approx. 45 m³/h Filling opening: 1,150 x 850 mm Channel format: 790 x 730 mm (W x H) Bale size: 790 x 730 x length in mm (W x H x L) Binding: 3-fold horizontal Wire push-through: seen in the direction of pressing on the left side Machine dimensions: approx. 4,250 x 2,580 x 2,000 mm (L x W x H) Machine weight: approx. 3,600 kg
Number Of Stations: 32 // Output (caps/min): 500
Offer 25374 Specifications: - Max. pressing force 100 t - Max. ram stroke approx. 500 mm - Lifting speed 25 mm/sec. - Return 125 mm/min - Installation height approx. 1000 mm - Projection to the middle of the ram 380 mm - Pusher clamping surface 530 x 400 mm - Plunger clamping pin 40 mm - Table size 750 x 560 mm - Table hole / through hole in the table 200 mm - Table height above floor 720 mm - Oil filling quantity approx. 200 ltr - Drive 400 V / 11 kW - Space requirement approx. W 1150 x H 3250 x D 1850 mm - Weight approx. 4600 kg
Number Of Stations: 24 // Output (caps/min): 600
Air Pressure: 40 bar // Delivery Rate: 1630 m³/h
Air Pressure: 40 bar // Delivery Rate: 950 m³/h
used
Capacity 50 tons Stroke 750 mm Table size 1500x1000 mm
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 45 to PRESS TABLE table surface (left-right): 700 mm table surface (front-back): 440 mm opening in bed (diameter): 40 mm SLIDE table surface (left-right): 410 mm table surface (front-back): 280 mm stroke rate (max.): 110 /min SLIDE (MECHAN. PRESS) slide adjustment: 65 mm stroke min.: 0 mm stroke max.: 90 mm main drive power: 5.5 kW TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 380 mm distance between columns (H-frame): 360 mm ATTACHMENTS (PRESSES) 2-hand engagement: yes foot engagement: yes European CE standards: yes
Properties: Volume 200 L Material V2A (AISI 304) 1.4301 Surface on the outside marbled III C Total height 1900 mm Overall height 1770 mm Cylinder length 1020 mm Diameter width 477 mm Operating pressure 0.99 bar Number of feet 3 or 4 [ 5000 characters max., no information on the advertiser ] Properties: Volume 200 L Material V2A (AISI 304) 1.4301 Surface on the outside marbled III C Total height 1900 mm Overall height 1770 mm Cylinder length 1020 mm Diameter width 477 mm Operating pressure 0.99 bar Number of feet 3 or 4 [ 5000 characters max., no information on the advertiser ] Properties: Volume 200 L Material V2A (AISI 304) 1.4301 Surface on the outside marbled III C Total height 1900 mm Overall height 1770 mm Cylinder length 1020 mm Diameter width 477 mm Operating pressure 0.99 bar Number of feet 3 or 4 Description Tank topstock: Manhol ...
pressure: 630 t diameter: 320 mm stroke: 310 mm total power requirement: kW weight of the machine ca.: 3500 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Dynajet 1000 me, used, blue Operating pressure: 1000 bar, Flow rate: 17 l/min, Drive: electric 35 kW, 400 volts, 63 A, Operating hours: approx.: 427 h, Trolly, incl. gun, 10 m HD hose, 15° flat spray nozzle,
upper amp; lower Wila tooling 5 axes: X / X´ / R / Z1 / Z2 Capacity: 50 ton x 2550 mm Backgauge: CNC Control: TS3 Passage between uprights: 2550 mm Max stroke: 265 mm Max distance between table -- ram: 515 mm Locking speed: 90 mm/sec Working speed: 20 mm/sec Returning speed: 90 mm/sec Electric motor (power): 9 kW Length: 3400 mm Depth: 1850 mm Height: 2820 mm Weight: 5 ton
A CNC sheet bending machine Amada is available. Working width: 4000mm, pressing force: 2200kN, stroke: 350mm, axes: 8. Machine dimensions X/Y/Z: approx. 5600mm/2650mm/3300mm, weight: approx. 18000kg, control: Amada. An on-site inspection is possible.
Manufacturer: EXNER Model: PG 80 Year of Manufacture: 2014 The EXNER PG 80 is a four-column hydraulic tool testing press for testing stamping, forming, embossing, and drawing tools. It is designed for high precision and durability, with modern proportional hydraulic control and digital force display for tool setup and testing. Technical Data Press Ram - Number of press cylinders: 2 pcs - Nominal force (adjustable): 2 × 400 kN - Return force: 2 × 150 kN - Stroke: 350 mm - Ram width: 2100 mm - Ram depth: 840 mm - Guide length: 750 mm - Ram speed under load (100%): approx. 0–10 mm/s - Ram return speed: approx. 0–20 mm/s - T-slots (DIN 650): 18 mm - T-slot pitch: 150 mm Installation Space - Installation height (top to bottom): 550 mm - Table width: 2100 mm - Table depth: 840 mm - Table T-slots (DIN 650): 18 mm - T-slot pitch: 90 mm - Table passage (W×D): 1300 × 120 mm (to be ...
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 50 to PRESS TABLE table surface (left-right): 700 mm table surface (front-back): 450 mm SLIDE table surface (left-right): 440 mm table surface (front-back): 360 mm spigot hole diameter: 40 mm stroke: 90 mm stroke rate (max.): 70 /min SLIDE (MECHAN. PRESS) slide adjustment: 70 mm stroke min.: 0 mm stroke max.: 90 mm main drive power: 3 kW TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 300 mm DIMENSIONS / WEIGHTS space requirements -left/right-: 700 mm space requirements -front/back-: 1295 mm total height: 2360 mm total weight approx.: 3000 kg
PRESS DESIGN drive system: eccentric / crank PRESS FORCES total force (nominal): 80 to PRESS TABLE table surface (left-right): 860 mm table surface (front-back): 620 mm thickness of bolster plate: 70 mm opening in bed (diameter): 165 mm SLIDE table surface (left-right): 570 mm table surface (front-back): 390 mm spigot hole diameter: 50 mm stroke: 120 mm stroke rate (max.): 67 /min SLIDE (MECHAN. PRESS) slide adjustment: 90 mm stroke min.: 9 mm stroke max.: 120 mm main drive power: 5.5 kW TOOL ASSEMBLY DIMENSIONS shut height (stroke down, adjustment up), BDC: 360 mm DIMENSIONS / WEIGHTS space requirements -left/right-: 1420 mm space requirements -front/back-: 1700 mm total height: 2990 mm total weight approx.: 5600 kg
pressure: 130 t chamfer lenght: 3060 mm distance between columns: 2690 mm column arm: 410 mm stroke: 215 mm dayligth: 385 mm ajustment speed: 200 mm/sec working feed: 1-10 mm/sec return speed: 135 mm/sec table width: 120 mm table height: 1050 mm tiltable up to: +/- 10 mm Number of working hours: 53.820 h compressed air: 5.0 - 7.0 bar oil volume: 250 l operating pressure: 340 bar voltage: 400 V total power requirement: 16.0 KVA weight of the machine ca.: 11250 kg range L-W-H: 3640 x 2210 x 2375 mm - in checked condition - machine video - https://www.youtube.com/watch?v=23IbxRaZ2KA Equipment: - CNC electro-hydraulic press brake - including DELEM CNC control model DA 65 swiveling control panel, front left 2D graphic programming & product display tool & program library including new TFT-LCD industrial monitor - CNC controlled axes: Y1 + Y2 / X / R - CNC electro-motor / controlled back st ...
Block size press Müro 5000/A4 WT; good condition; cleaned and tested; Heat baffle; Stack increase; with dryer. Block gluing machine Müro 5000/A4 WT; good condition; cleaned and checked; pile elevation; heating sheet; with heater.
Key data: 600 t
Max Tool length: 3000mm Max Tool Width: 2000mm Min Tool Height: 500mm Total Tool Weight: 20,000kg Max Closing Speed: 400 mm/sec
Rutil Vertial Injection Moulding Machine Year of manufacture: 2001 Type: Injection Configuration: Vertical Clamping force: 350 tons Injection volume: 2000 cc Upper intermediate frame: Yes Lower intermediate frame: Yes Heater plate dimensions: 600×650 mm Tie bar distance: 600 / 340 mm Additional heating option: Yes Sliding plate: Yes
Manufacturer: Hans Schoen Model: NH 160 Year of Manufacture: 1988 rebuilt in 2016 The press is being sold without tools or spare parts. Technical Data Press force max.: 1,600 kN Main drive power: 30 kW Speeds Rapid advance from: 300 mm/sec Pressing speed: 18 mm/sec Rapid return: 300 mm/sec Strokes Max. stroke: 150 mm Max. daylight opening: 450 mm Table and Ram Dimensions Ram area: 730 × 560 mm Table area: 650 × 650 mm Openings Front vertical opening: 750 mm Side vertical opening: 250 mm Heights Table height above floor: 850 mm Table bore diameter: 150 mm Ram bore, Ø H7: 60 mm T-slots T-slots in table, DIN 650 H12 diagonal: 22 mm T-slots in ram, DIN 650 H12: 22 mm Two pieces, front to back Machine Dimensions Machine footprint approx.: 1,850 × 1,500 mm Machine height approx.: 2,850 mm Find more here - .ucymachines/ Contact us at - sales@ucymachines
Maximum pressure: 50 tons Year of Make: 2006 Pressing force: 65 tons/m² Number of bindings: 4 vertical Channel cross-section: 750 x 1000 mm Dimensions of the tailgate: 920 x 1400 mm Bale weight: 350-500 kg Weight: approx. 13 tons Power connection: 400 V/ 22 kW Bale tying: automatic
Key data: 60 t, 370 mm, 10 mm
Eccentric Press Compressive Force 60 Ton Equipped: -Hydraulic clutch -Hydraulic overload protection
Simimpianti 3500×1300 veneer shelf press Shelf length 3500mm Shelf width 1300mm Two Batches Press on 8 cylinders Shelves heated with CO water Operating pressure max 300bar Piston diameter 80mm Machine Weight 7000kg Machine dimensions 435x160x235cmH Net price 65,000zł
Electricity connection 400V 13kW 2 heating plates à 1200 x 2250 mm Heating plates controlled by 2 thermostats Press pressure at 250 bar LxDxH: 2590 x 1330 x 1950 mm Weight approx. 2800 kg Press thickness 380 mm
Offer 25450 Specifications: - Compressive force 100 t - Projection 300 mm - Table size approx. 650 x 450 mm - Height-adjustable table - Diarrhea hole in the table approx. 200 x 100 mm - Large installation height approx. 450 mm - Plunger area 70 x 140 mm - Peg hole in the ram 40 x 80 mm - Tappet adjustability 60 mm - Stroke adjustment 10 - 100 mm - Stroke rate 80 rpm - Pneumatically assisted coupling - Drive 380 V / 5.5 kW - Space requirement approx. W 1350 x H 2550 x D 1600 mm - Weight approx. 5000 kg
Offer 25471 Specifications: - Compressive force 75 t - Projection approx. 300 mm - Table size approx. 800 x 600 mm - Height-adjustable table - Stroke adjustment approx. 16 - 140 mm - Plunger adjustment 80 mm - Stroke rate 80 rpm - Pneumatic connection - Drive 400 V - Space requirement approx. W 1800 x H 2450 x D 2000 mm - Weight approx. 4000 kg
It is a used, reconditioned Fortuna bun press fully automatic for sale. The machine head can be swivelled electrically and switched off with active movement. Weight range of the machine is 40gr. - 110gr. per piece of dough (30 pieces). Incl. 3 x plates (more plates on request). Price on request.
The Dorst TPA 15/3 is a used mechanical powder compaction press designed for precision and efficiency in industrial applications. It provides a maximum pressing force of 150 kN and a withdrawal force of 100 kN, supporting a variety of compaction tasks. With an upper punch stroke of 100 mm and a range of 70 mm for adjusting the travel, this machine offers flexibility for different requirements. Operating at speeds of 7 to 32 strokes per minute, it ensures a reliable production throughput. This press allows for a maximum filling height of 70 mm and pressing travel up to 35 mm, suitable for a range of powder compaction needs. The machine is fitted with a compressed air system that has an intake of around 70 liters per minute and a total connected load of approximately 6 kW. It is compact yet robust, with dimensions of about 1400 mm in width, 1300 mm in depth, and 2650 mm in height, weighing ...
Technical data: Material width: min. 130 mm, max. 270 mm Material width: max. 244 mm Print repeat length: min. 101.6 mm, max. 254 mm Machine components: • Corona treatment • 5 × offset printing units • 1 × flexo printing unit • Flat hot foil stamping unit • Flat die-cutting unit
The Dorst TPA 6 is a used mechanical powder compaction press suitable for various industrial applications due to its robust performance and flexibility. It boasts a maximum pressing force of 60 kN and a withdrawal force of 30 kN, addressing a wide range of compaction needs. The machine supports a maximum filling height of 70 mm and a pressing travel of 30 mm, with an upper punch stroke of 95 mm and an adjustable travel of 50 mm. This ensures precise control over the compaction process. Operating at speeds between 7 to 32 strokes per minute, the Dorst TPA 6 consumes approximately 70 liters of compressed air per minute and has a total connected load of about 3.5 kW. It measures 2220 mm in width, 1060 mm in depth, and 2250 mm in height, weighing around 1,200 kg. With a gear oil capacity of 12 liters and a workplace-related sound level of 75 dB(A), it is designed to endure continuous use whi ...
Key data: 100 t, 330 mm, 10 mm
Press Type P 100 RE Pressure 100 ton Free passage between the two uprights 420 mm Slab dimensions 610 x 410 mm Table dimensions 950 x 650 mm Installation height plunger lower 400mm Plunger position 90 mm Stroke rate 55 min Motor power 7.5 KW Weight 7000 kg Press is equipped : - Air coupling - Hydraulic overload protection
The Dorst TPA 4 is a used mechanical powder compaction press well-regarded for its sturdy performance in various industrial settings. It features a maximum pressing force of 40 kN and a withdrawal force of 30 kN, making it versatile for different compaction tasks. With a maximum filling height of 70 mm and a pressing travel of 30 mm, this machine efficiently handles varied operational demands. The upper punch has a stroke of 95 mm with an adjustable travel of 50 mm, enabling precise control during processes. The press operates within a speed range of 7 to 32 strokes per minute, consuming around 70 liters of compressed air per minute and requiring a total connected load of approximately 3.5 kW. It is designed with dimensions of 2220 mm in width, 1060 mm in depth, and 2250 mm in height, while weighing about 1,200 kg. The gear oil capacity is 12 liters, ensuring durability and the ability t ...
Roll Press Fortuna Semi-Automatic Size 4 Semi-automatic 30-piece machine for perfect dough pieces Robust design for long service life Parting head NEWLY revised Dough filler up to 3300g, Low space requirement Connection 400V, 16A-CEE plug Dimensions: 580 x 580 x 1350 mm, WxDxH Used machine overhauled Quality from a specialist company! Benefit from over 35 years of experience! Option: Stainless steel pedestal Wirkteller Neu Service Package Maintenance contract Instruction & Commissioning Delivery
Pass-through press for glued glue ITALPRESSE PL/9 Shelf length 3000mm Shelf width 1300mm Number of vertical cylinders 6 Pressure of 90t vertical cylinders Diameter of vertical cylinders 70mm Number of horizontal cylinders 6 Heating shelves with a high-frequency generator The line consists of: -Material feeding section -Glue application section -Material loading section -Press PL/9 -Material receiving table CE Certificate Line dimensions 740x770x235cmH Weight about 8000kg
Used Roll Press FORTUNA, Machine Size 4 -In Bakery Condition- - 30 hollows per plate - Weight range: 40 - 110g - Condition: very good, - Video on request A viewing is of course possible by arrangement.
A high-pressure pump BFT with Rexroth and VEM components is available. Pressure: approx. 4000bar, motor power: approx. 37kW. An on-site inspection is possible.
ID3680 Haarup Mixodatamat 1200/2000 year/Year of construction 1993 Slab press for 50mm slabs with backing concrete, with mixer, portioning, press, including steel pallets for picking the pressed slabs. Slab press for 50 slabs with back concrete, with mixer, portioning, press, incl. steel pallets for picking the pressed slabs
Fritz Shuttle Table Press Closing force approx. 300T Platen 2.7 m x 1.8 m deep 3x adjustable platens top and bottom Type of heating: induction Shuttle located at the rear of the press Used for rubber moulding
Haco PPM 175 ton x 3600 mm Capacity: 175 ton x 3600 mm Backgauge: electric Passage between uprights: 3150 mm Max stroke: 200 mm Max distance between table -- ram: 450 mm Depth of throat: 300 mm Locking speed: 80 mm/sec Working speed: 9 mm/sec Returning speed: 95 mm/sec Electric motor (power): 15 kW Length: 3880 mm Depth: 1750 mm Height: 2750 mm Weight: 13,4 ton
Specifications: Pressure: 50 t Bending length: 2000 mm Equipment: - Backgauge - Emergency stop push button - Foot control
pressure: 30 t throat: 250 mm table-size: 650 x 500 mm stroke: 400 mm dayligth: min. 120 / max. 500 mm Control: Simatic HMI Touch Siemens total power requirement: 13 kW weight of the machine ca.: 3,5 t dimensions of the machine ca.: 2,5 x 1,70 x 2,85 m Setup mode and single stroke operating mode Two side tables with a support surface of 850x500mm with hydraulic ball bars for heavy workpieces The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Offered is a Kocher + Beck rotary die cutter/rotary die cutting technology. SKK: scale front stop 5, scale on cylinder 9, 10bar, Mini B (pressure downward): scale front stop 11, scale on cylinder 5, 20bar, Memobox carton: scale front stop 3, scale on cylinder 11, 40bar, Memobox insert: scale front stop 5, scale on cylinder 5 & 2mm, 10bar. Inspection by appointment possible.
CONTROLS PC controller BECKHOFF Offer for services of complete Overhaul of a Customer-Owned Fineblanking Press FEINTOOL GKP 160 Scope of Overhaul • Complete disassembly into individual components • Inspection of all parts, including crack testing of critical components • Overhaul of the drive system, new motors • Reworking and precise alignment of all guideways • Complete overhaul of the hydraulic cylinders • Overhaul of the clamping tables • Installation of a new hydraulic unit • Renewal of the pneumatic system • Renewal of the electrical system Modernisation / Retrofit • Combined table • Servo feed systems • Central lubrication system • RAZIOL band lubrication • New brake/clutch unit • BECKHOFF PC-based control system with touch panel • PILZ safety control system • Implementation of CE conformity Notes • Special options and customer-specific ext ...
A Strautmann plastic briquetting press is available. Pressing force: 300kN, hopper type: TS 1600, system dimensions X/Y/Z: approx. 6750mm/1900mm/2750mm. Documentation available. An on-site inspection is possible.
maximum number of results exceeded
please refine your search
