synchronous used for sale

Number of sanding units: 4 St sanding width: 190 mm Sanding height max.: 4-180 mm weight: 4200 kg Hess Expert 4-belt single wood sanding machine -------------------------------------- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimen ...

Manufacturer: Costa, Type: CCC + CCC 1150, Year: 1998, Monting of the machine: obenWalze/Walze/Walze , Equipment of machine 2: untenWalze/Walze/Walze, Double sided sanding line: yes, Sanding width mm: 1150, Sanding hight mm: 120, Number of sanding belts: 6, Sanding belt dimensions: 2620 X 1150, Table hight adjustment by engine: yes, Rubber roller: 3 +3, Shore roller 1: 70, Shore roller 2: 70, Walze 3 Shorehärte : 60, Längsschleifaggregate: ca.34, Belt 2 shoe unit: ca.22, Belt 2 synchronous and reverse run: ca.17, Belt 3 synchronous and reverse run: 34/22/17, Table hight adjustment by engine: yes, Combi unit roller/shoe: 8-20, Table hight adjustment by engine: ca 3 + 3, Abrasive belts at bottom: yes, Intermediate sanding of lacquer: yes, Programmanwahl extern: yes, Pressure pads for short workpieces: 150, Year :1998

Linear unit with planetary gearbox, stroke 1028mm, RK Monoline Z 60, RK Rose+Krieger, used Top Used - top condition like a demonstration unit The part was removed from a pilot system that was only used for a short time and is in almost new condition. Special price We still have several identical and other such devices, but the amount is ending. Buy more than 1 piece, there is still a great discount. The current price of a similar product is € 1980 excl. VAT. If you have a VAT number, we will gladly issue you an invoice without VAT. Technical data: - Linear unit RK Monline Z 60, with toothed belt drive, RK Rose+Krieger, - Incl. 2 tables 187 x 140mm, table 1 is driven, table 2 is freely movable - the 2nd table can be removed - Max. stroke when using one table = 1028mm - Variable positioning of the drive - Connection linear unit - Gearbox with backlash-free Rotex ...

Tenoning spindle: 1 0 Number of milling agregates: 5 St. Spindle diameter: 50 mm control: Weinig, PC-Nexus # 2732 Weinig Unicontrol 6 with NC spindles ------------------------------------------------ Machine is in checking process at the moment! Technical data summary (please inquire about any additional accessories included) Pos. 1: Crosscut saw ------------------------------------------------ > Number of tools: 1 piece. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Tool diameter max.: 400 mm > Motor power: 3 kW > Adjustment path radially pneumatically controlled to 8 positions, e.g. for edge rounding from above > Laser directional light to detect the saw section Pos. 2: Rounding unit horizontally at the bottom ------------------------------------------------ > Position: horizontally below > Motor power: 1.5 kW > Spindle diameter: 20 mm > Clamping length 25 mm > Spindle spee ...

Tenoning spindle: 1 St. Number of milling agregates: 4 St. Spindle diameter: 50 mm control: Südtron BT 20 Weinig Unicontrol 6 --------------------------------- General data --------------------------------- Loading dimensions approx. 5000x2400x2400 Machine weight approx. 3000 kg crosscut saw --------------------------------- > Pneumatic crosscut saw, against 8-fold turret stop > Spindle speed: 2800 > Spindle diameter: 40 mm > Tool diameter max.: 350 mm > Motor power: 3 kW > Laser directional light to detect the saw section Length stop - clocked --------------------------------- > Length stop 2700 mm 1. Tap and slot spindle --------------------------------- > Number of tools: 3/4 pieces. > Tool clamping length: 320 mm > Vertical pneumatic spindle stroke: 240 mm for wood thicknesses IV 68-92 > Spindle speed: 3500 rpm > Spindle diameter: 50 mm > Tool diameter max.: 320 mm > Motor power: 11 ...

Number of spindles: 4 St. Number of tools: 11 St. Spindle diameter: 50,40 mm Spindle length: 285,125 mm length: 4000 mm width: 2000 mm height: 2200 mm Weinig Univar 10/3 folding machine --------------------------------- Machine will be cleaned and chcked before delivery For milling around windows, doors and the like with uneven circumferential profiles. Machine suitable for wood thickness 68 to 92 mm Time required per frame milling, medium size 1.20 x 1.20 m - approx. 2 minutes. The available tool positions are selected using a selector switch on the control panel retrieved. Machine with 3 hydraulically controlled right precision Lifting spindles for holding 3 tool sets, 2 x 95 mm spindle stroke per spindle The spindle stroke takes place in a U-movement, so that the opening is possible for short parts The milling stop remains as small as possible. Spindle stroke horizontally fine Adjusta ...

We offer two Ford gas cogeneration plants for sale. Synchronous generator: Emod 19 KVA Engine: Ford Voltage: 230 / 400 3 phases Frequency: 50 Hz Speed: 1500 rpm COS phi: 0.8 Starter: 24 V Weight: 900 kg Year of construction: 1996 Hours of operation: 24,000

STAMFORD Synchronous Generator HC. I 734 E2-CG 1215 KVA 400 / 231 V 1754 A 50 Hz, 1500 rpm. Accessories: - Winding PT100 - AVR MX321, PFC-3 COMPLETE OVERTIME in June 2017

- Hobelbreite 50 - 400 mm - Hobelhöhe 10 - 300 mm - stufenloser Vorschub 5-25 m/min. - Spindel FI 50 mm - Drehzahl 6000 U/min - 6 Spindeln - untere Welle min. / max. Werkzeug FI 160 /180 mm - rechte Welle min. / max. Werkzeug FI 160 /230 mm - linke Welle min. / max. Werkzeug FI 160 /230 mm - obere Welle min. / max. Werkzeug FI 160 /230 mm - 2. obere Welle min. / max. Werkzeug FI 160 /230 mm - untere Welle min. / max. Werkzeug FI 160 /230 mm -max. Sägeblattdurchmesser 2. obere Welle 300 mm Motorleistung: 1. unten 15,0 kW 2. rechte 11,0 kW 3. linke 11,0 kW 4. oben 15,0 kW 5. oben 15,0 kW 6. unten 15,0 kW - Motor Vorschub 11,0 kW - Motor Höhenverstellung 1,5 kW - Gesamtanschluss 94,5 kW - Jointer obere Wellen und unter Welle - horizontale Wellen mit Gegenlager / Hydrospannung - obere Welle elektrisch verstellbar mit Vorschubsystem mit Digitaler Anzeige - linke Welle elektrisch verstellb ...

TECHNICAL INFORMATION Manufacturer: AMMANN Name: Two-shaft continuous mixer Type: AMIX2_4CB Built: 2010 Continuous power: 180 cbm/h Gross volume: 4.12 cbm Net volume: 3.71 cbm Filling level: 0.64 Drive power: 2 x 45 kW Length inside: 2,400 mm Inside width: 1.910 mm Stirring circle diameter: 1,080 mm Axle spacing: 830 mm Weight: 7.700 kg Drive type: V-belts and synchronous transmissions SPECIFIC COMMENT - Mixing trough with electro-pneumatically actuated outlet valve (300 x 650 mm) - Stirring arms with honeycomb blades and screwed agitator arm protection - Automatic central lubrication unit with grease flow monitoring - Mixer camera - Little operating hours and wear - Plant is dismantled and cleaned If there is any interest, we are happy to send you an offer with photos. EuroConsult Dimitrios Piretzidis

The synchronous generator Flash 2500 S is in good condition, ready to use. Built in approximately 1997 Weight 36 kg 230 V, 50 Hz, 9.7 A 2 kVA 3000 min IP 23 Altitude 100 m above sea level. NN Ambient temperature 27 � C Radio interference level DIN 57875 spare parts/service MATEC CH-4952 Eriswil/DE-79618 Rheinfelden Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

GUK Slitting Machine RS 21/760 Technical details: -No double bows, false bows and no risk of mixing! -Insensitive to static charge -approx. 20% cost savings compared to processing batch goods -Automatic control of the cutting position -Synchronous control of the print mark -Installation of code readers additionally possible -Storage in maintenance-free needle and ball bearings -Paper roll on top, single or double roll stand -With and without integrated adhesive table -Drive left or right, with chain or timing belt -Smallest fold 15 mm -With automatic roller changer ARW 21 Specifications: -Min. format: (WxL) 60 mm x 105 mm -Format: (WxL) 210 mm x 315 mm -Roller outer diameter: max. 600 mm -Roll core diameter: Europe 70 mm USA and Japan 76 mm or 152.4 mm or 3 inch or 6 inch -Power: 300/minute, depending on section length -Capacity: For paper roll by. 600 mm, sectio ...

Used Heuft Empty Bottle Inspector InLine IXs reflexx Device No. 2ZG044698 Condition: very good, ready for use at short notice ·       Commissioning 6 May 2012 ·       Upgrade for later integration of additional ground control using X-ray technology ·       Tape control Heuft Synchronous TX ·       Network Heuft Hlan ·       Haylofts two ways discharge with div. Heuft container transport Convejor ·       Troubleshooting Software Wizard ·       Software assistant guided instructions for the different container changes ·       Power max. 46,000 fl./h ·       5 Variety licenses incl. scope of delivery: ·       Belt control Spectrum TX ·       Measuring bridges for inlet control and discharges incl. height connections ·       2 x Discharge Delta K  ...

1 very well preserved double girder crane ideally suited to the transport and use of long goods crane driving towards Load approx. 4 x 4,000 = 16,000 kg track width approx. 20.565 mm Hook path about 6.500 mm Make steel Year of construction/renovation 1990/1993 Workshop overhaul 2016 FEM 3 m Crane equipped with high-quality wind factory units, synchronous and separately controllable to apply loads, radio control Working speeds: Hoist CA. 1,2/12.0 m / min Trolley gear approx. 5.0/20,0 m / min crane chassis approx. 10.0/40.0 m / min

Two used 8110 KVA Syncronous A.C. 11KV generators( generator end ) for sale. The alternators is in a very good running condition.It was driven by a Siemens Tornado gas turbine. The location is our warehouse in solingen, germany. generator end: Synchronous A.C. Alstom Type: CGS710N2240U voltage: 11.000V electrical power: 8110 KVA rpm: 1500 rpm Year of construction: 1999 Weight: 17t Price on request Here you can download the generator pictures (4 MB): abc.stromerzeuger-discount.de/Alstom-Generatoren/P140796-10.zip

Single Slab Reheat Furnace • Type: Walking Beam • Manufacturer: Davy • Capacity: 150 t/h • Inside Refractory Width: 8,35 m • Effective Length: 32,6 m • Slab Thickness: 160 mm • Slab Maximum Length: 7,5 m • Primary Fuel: mixed BFG and COG • Alternate Fuel: N°6 Fuel Oil • Commissioned in 1995 Water Descalers • Primary descaler at slab reheat furnace run out table • Front and back 3 Hi Rougher Mill descalers. • Finishing Mill descaler at run-in table. Water Descaling Pumps • Manufacturer: Union Pump Company • N° of Pumps: Two (one operating, one stand by.) • Power: 5.000 HP (3.730 kW) • Pump Speed: 4.500 rpm • Discharge Pressure: 127 barg (1.840 psig) Rougher Mill • Type: 3 Hi, one stand 22" x 34" x 100" Reversing Mill • Manufactured by Blaw-Knox in 1923. • Ma ...

CHP with John Deere gas engine and 70 kW of electrical power New exhaust gas turbocharger Control AMG 2 with leanox control Synchronous Generator Stamford 70kW Complete with frame,sound hood Automatic oil refilling with internal silencer and exhaust heat exchanger Operating hours approx.42,000 Suitable for biogas and natural gas

Machine details Bearing number 1105-03062 Machine type Machining center - Horizontal Make MAZAK Type FH 680 Built in 1997 Control type CNC Warehouse FRANCE Country of origin Japan Delivery time immediately Freight base from location Technical details x-way 1050 mm y-path 800 mm z-way 880 mm Control MAZATROL M plus Pallet changer type 2-fold Pallet size 630 x 630 mm Tool changedevice 40 Tool holder bt 40 Table load 1 t Pallet change time 6 sec Rapid response 40 m/min Feed 1-40,000 mm/min Speed 35-7000 rpm Drive power 30 kW Workpiece dimensions max. 1000X 1000 mm Tool diameter 135/260 mm Tool length - max. 500 mm Tool weight max. 7 kg Total power requirement 45 kVA Machine weight approx. 15 t Space requirement approx. 19 m2 Information High-pressure cooling by spindle 20 bar MAZATROL m plus Synchronous thread cutting NC Round table 0.001° x 360,000 p ...

A quadroblock of Krones SUPERBOLCK is offered All machines are powered by cardio-shafts and please and a synchronous movement of the bottles. This achieves outputs of up to 37,000 bottles per hour. The system includes the following machines: Exhaust Rinser: Kom 560-002 Vacuum Filler: Kom 307-551 Shooter: SV 15 Etyma: Starmatic 24-8-8 Kom. 090-952 Bottle format: 20ml (can be adapted to customer requirements) Capacity: 7000-37000 bottles per hour Built: 1994 Plant condition: The system is completely overhauled Made in GERMANY For more information please contact us. Tel.: +49 6061 968 78 22 or email: v.gurin@allfill.de

rolling capacity max.: NA t workpiece diameter: 38 mm workpiece length: 500 mm total power requirement: 24 kW weight of the machine ca.: 10 t dimensions of the machine ca.: m Max.Ø tool slide stroke 760 mm Max.Ø rack length 610 mm Length of workpiece between centres, approx. 500 mm Max. tooth width / profile width 92 mm Max. workpiece Ø 38 mm Tailstock stroke on outboard support, hydraulic, approx. 500 mm Module range 0.3 - 1.3 Total electrical load, approx. 24 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features KBH Workpiece Feed Device, standing parallel to the machine, at present set-up for feed-in and feed-out of shaft-formed workpieces, approx. Ø 16 x 200 mm long, with prism conveyor belt and lifting station for 2 shafts (blank and finished part), as well as workpiece positioning control. Originally, external gears were formed on the machine using  ...

Table dimensions: - mm Motor output: 7,5 kW Spindle diameter: 40 mm reus: 6000 U/min Weight: 300 kg Year: 2018 Universal profiler Götzinger UP 1730 Machine for frontal and cross-side machining. Different application technology for wood products First-class surface quality of machined workpieces due to high speed, Particularly stable bearing of the milling shaft and through synchronous milling. Rapid tool change through one-sided mounted cutter shaft and through swiveling clamping device. The whole work process, such as clamping, pneumatic-hydraulic table feed with speed control (stepless) and fast reverse. By exchanging the milling segments and by changing the attachment points can be up to ten different with a single profile milling set Create profile companies. Technical specifications: Cutting depth max .: 30 mm Milling height max .: 150 mm Voltage cross section per stroke max. Softw ...

working length: 3100 mm Working width: ca. 3400 mm Working height: 750 - 1000 mm Haberkorn return means for Umfälzautomat For frame from 300 mm to 3000 mm for automatic Return consisting of: First cross roller conveyor approx 3100 mm long ------------------------------------------------- built-in conveyor belts for depositing the wing on the cross roller conveyor with about 10 mm stroke Driving speed of about 5-30 m / min. Roller diameter 80 mm Rollers with PVC coating Gear motor with 0.37 KW 2 Synchronized lifting device for cross roller conveyor -------------------------------------------------- ------------------------ built-in rollers with stepless drive about 5-30 m / min. max. 100 mm stroke Roller diameter 80 mm Rollers with PVC coating Synchronous storage of GG 25 hardened gears and rods 2 pneumatic cylinder 80 x 100 mm adjustable stops (top - down ) Synchronization via shafts  ...

Bosch Rexroth Linear Cylinder Machine The machine is a special production for Bosch for its own use in the production process. The machine contains: Rexroth MSK050C-0600-NN-M1-UG1-NNNN 3-Phase Synchronous PM Motor Festo DGC-40-650-KF-Y5R-A 532449 H608 Rexroth EMC-063-NN-2 Schischke MY_1106 E2 - Voltage 380-480, 6 bar, 1300 kg, year of construction 2016 Condition: used The plant is located in Hildesheim and can be dismantled and picked up there by the customer. Dismantling and transport according to offer and agreement also possible by us. Complete plant closure, large selection of mezzanine, pallet racks, shelves, paternosters. High-quality industrial machines, lathes, grinding machines, manual machines

max. wheel diameter: 0 mm max. number of teeth: 0 max. module: min. module: total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m CNC controlled milling machine for synchronous rings The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

From stock unused Bosch Rexroth MST251F-0040-FT-NOCN-D303 Synchronous Torque Motor !

Frequency controlled pump, TPE2 80-180 N-A-F-A-BQQE, Grundfos, new -30% - Single-stage inline pump (glanded pump) with speed-controlled, fan-cooled permanent magnet synchronous motor, - 50.5 m³/h, 360 - 4000 rpm, 2.2 KW, 12.8/18m, DN80, 10bar, 3x380-500V, - Grundfos 98437605, control panel HMI 200 standard, function module FM 300 - Frequency converter MGE90LD 2-56C-IA For air conditioning of commercial buildings, heating for commercial buildings Hot water circulation in commercial properties and much more. Special price ! The current new price of a similar product is € 4.800 excl. VAT. We still have several identical pumps, but the quantity is ending. Buy more than 1 piece there is still a great discount. If you have a UID number, we will gladly issue an invoice without VAT. As good as new in original packaging! The part was bought from a spare parts store of a co ...

Diesel combined heat and power plant, CHP, generator set, power generator used DIETER KUNZLER GmbH Generator K-EA-3ST-PAR-SYN-M 500 kVA 400/231 V Synchronous 3x 362 A 50 Hz Mtu 12 V 183 AA 31 MERCEDES OM 424 225 kW 1500 rpm Dimensions unit: approx. 2500 x 1200 x 1500 mm, control cabinet approx. 2400 x 500 x 2000 mm Changes and errors in the technical data, information and prices as well as prior sale reserved.

A rotating frequency generator generates 60Hz alternating current from 50Hz alternating current. In good condition. The device can be converted into a diesel generator. Manufacturer: YAMADA DENKI CO LTD Type: RFC-3543E; Series: 80155 Power: 350 kVA Input: 415 V; 50 Hertz Output: 415/215 V; 60 Hertz Operating hours: 3624 h Electric motor: AM-355 W; 350 kW; 415 volts; 546A; 50 hertz; 1500 rpm Synchronous generator: M3834; 400 kVA; 415/210 volts; 60 hertz; 1400 rpm

Currently in stock! AGG 200_COK3 Achievement: PRP: 200 kVA / 160kw ESP: 220 kVA / 176 kw 50 Hz 400 volts Disposals: 3-pole terminal block, neutral conductor. Earthing. Engine: Cummins QSB7-G5 Cylinders: 6 incl. starter battery Fuel: Diesel Emission level 0 Generator: Stamford UCI274H 1-bearing Synchronous generator with AVR voltage regulation analogue, directly with Steel disc clutch flanged to engine. Construction: Without sound hood. Control: Cummins PowerComand1.2. Net weight: 2117 kg Dimensions: 2656 x 1130 x 1822 mm Delivery possible on request! Net price plus VAT. The General Terms and Conditions of Business, Delivery, Payment and Installation of Aggretech GmbH shall apply exclusively) G22I809262

technical details: - suitable for heavy starting machines - 18 l large tank = long running time - electronic voltage regulation (AVR) - Thermo-magnetic circuit breaker against overload and short circuit due to defective loads and cables - Insulation monitoring = safe personal protection - Oil deficiency shutdown - E-Start = high comfort Metrics: - Length: approx. 842 mm - Width/depth: approx. 523 mm - Height: approx. 557 mm - Weight: approx. 96 kg Drive: - Engine: Honda GX 390 - Power factor: 0.9 cos ɸ - Starter: E-Start / Hand Start - Type of fuel: Gasoline - Tank capacity: 18 l - Consumption at 75% load: 2.2 l/h - Sound pressure level Lp: 72dB(A) - Sound power level Lw: 97 dB(A) Generator: - Type: Synchronous - Rated voltage: 230 V - Apparent power at LTP: 7.2 kVA - Active power at LTP: 6.4 kW - Apparent power at COP: 6.0 kVA - Active power at COP: 5. ...

Turbine Nadrowski Superheated steam turbine Brand turbine factory Nadrowski Type B 5 S4+GIV/V Year of construction: 1989 for generating electricity from superheated steam Maximum steam temperature 400°C Working pressure 4-31 bar Maximum power 632 kW with Synchronous Generator AVK DKBN 100K/800-4 Power 813kVA, current 1173 A regularly serviced External dimensions approx. L 4 m x W 1.50 m x H 1.50 m

• 120 tons total pressing force • Pressing area 3,000 x 1,350 mm • With patented, thermostable electric heating plates with automatic temperature control system • Connected load of the heating plates with economy circuit 10.6 kW • Connected load of the hydraulics 2.2 kW • in 6-cylinder version Ø 85 mm • Lockable main switch • Push-button control • Stop button • Safety ripcord, safety edge • Timer with automatic opening and acoustic signal • Stroke = opening 400 mm • Infinitely adjustable stroke limitation • 2-stage hydraulics with automatic pressure follow-up • Compact hydraulic power unit mounted maintenance-free in the oil tank • Teflon bronze guides in the cylinders • Hard chrome-plated steel pistons • Heavy rack and pinion compensation for synchronous table movement • fully open on four sides • Economy circuit installed as s ...

Ball-bearing linear guide with 2 carriages, MR55-A2-1244-22-22-G1-V3-GP, Schneeberger, as good as new As good as new in original packaging! The high-quality part comes from a spare parts warehouse of a mechanical processing of a large automobile manufacturer, has been in stock for some time, is completely new and in the original packaging. Attention: We have many, bearing, high-quality ball screws, synchronous motors and linear guides in different designs. Take a look at our website of IPV GmbH. Linear guide with ball chain type MR55-A2-1244-22-22-G1-V3-GP of Schneeberger consisting of: -1 guide rail 55mm x 1244mm long - 2 pcs. guide car MR55-A2 Functional guarantee! For second-hand parts, we cannot provide a conventional guarantee and warranty. However, we give you a functional guarantee. If the device does not work during commissioning, you can return the goods and we ...

Jenacher diesel emergency generator with a MAN 2842 LE diesel engine and a Hitzinger Synchronous generator . Complete with switch box and heat extraction from Jenbacher with 235 kW from the exhaust heat

Linear unit, linear axis, portal axis with servo drive, synchronous servo motor, electric slide, loading unit, linear guide with servo motor and pneumatic gripper REXROTH INDRAMAT Type: MKD0771B-061-KP1-KN Ident No. 247238 0001 Year of construction: 2000 Axis movement: 2400 mm Carriage length: approx. 500 mm Total length: 3520 mm- pneumatic feed pliers (clamping pliers with 2 Festo compressed air cylinders) - Standard linear guide 65 x 25 mm - Basic profile made of steel - Ball screw 32 x 10 mm- pneumatic with position indication - permanent servo motor type: MKD071B-061-KP1-KN (Part No: 261989, S. Nr. MKD071-50234, brake with 24 Volt DC) Overall dimensions L x W x H: 3520 x 400 x 580 mm Weight: 340 kg good condition; used

Spiral dough mixer with fixed stainless steel kettle for max. 120 kg dough. Vat cover with swivelling lid part, motor protection by overcurrent relay, electrical switching and control unit in the machine. Kneading process over time with 2 timers and synchronous motor, with automatic switching and switch-off. -Type: SP 120 D -mobile -for max. 75kg flour or for max. 120kg dough- -with 2 automatic timers -Stainless steel spiral and boiler -Boiler diameter 75cm -Boiler capacity approx. 180 litres -Machine mobile on castors with a swivel castor -Locking by 2 locks -with plastic flour dust cover -400 Volt Frequency 50 Hz -8 kW 18A -Weight of the machine approx. 550 kg -Condition "very good" as good as new

Standard configuration Machine ? Closed machine frame with integrated laser unit ? Motion unit for high precision processing ? Gantry drive in combination with direct linear drives ? Automatic pallet changer ? Longitudinal conveyor for small parts / slag ? Enclosed beam delivery system ? 19? Touch screen ? Working area lighting ? Positioning laser diode ? Spray device ? PierceLine ? FocusLine ? NitroLine ? PlasmaLine ? Automatic nozzle cleaning Trumpf Laser ? New generation CO2-Laser TruFlow 6000, energy-efficient ? Maintenance-free radial turbine blowers ? Radio-frequency excitation ? Laser control TASC ? Laser power control ? Logbook function Laser Laser cutting head ? Laser cutting head with 250 mm lens ? Universal quick-change device UTI ? LensLine with status control ? ControlLine: Height regulation and sheet edge sensing ? Lens with RFID-chip Control ? Easy shopfloor programmi ...

Automatic Packing Machine: OMRON PLC Controlled, equipped with 2 volumetric cup and 1 auger filling system. Applicable for granule (2x) and powder (1x) packing. Standard Features integrate metering, bag-making, packaging, sealing. Standard positioning with servo film transporting system. Stable for transporting film with two synchronous belts. High automation with auto correction function. Reasonable structure, convenient adjusting operation and maintenance. - Specification: max. speed of the machine in neutral: 60 cycles/min | bag size: L(50-240mm), W(50-200mm) | the max width of packing film: 420mm | thickness of film: 0.04-0.09mm | bag making mode: 4-side seal bags | air consumption: 6bar 2.0m?/min | power/voltage: 2kW/220V, 50 Hz, ca. 3-4kW | dimension (LxWxH): 1600?1600?1800mm | weight: 500kg (depending on final fitting) | body: SS304 | touch screen: 7 colour | PLC by OMRON, Control ...

Key data: 1400 V, 1800 , 400

MWM Power Generator TBG620-V16K Gas generator set from 2001, Scope of delivery: base frame and generator, as shown. Without turbocharger, gas mixer, oil cooler and intercooler. Camshaft has signs of wear on the B side. 1 available 1,365 KWel x 1,500 rpm, 400 V/50 Hz. AC generator: Stamford HC I734G2 CG, 1,800 KVA Gas engine MWM TBG620-V16K Manufacturer: MWM Model No.: TBG620-V16K Type: Gas generator set Serial Number: 2203156 Power [KW]: 1.400 Year of construction: 2001 Hours:– Weight [kg]: 8.588 Dimensions LxWxH [cm]: 470×145 AC generator Stamford HC I734G2 CG Manafacture: Stamford Model: HC I734G2 CG Type: AC Synchronous Generator Serial Number: 0140886/06 Power [KVA]: 1,800 Voltage [V]: 400 Frequency [Hz]: 50 Current [A]: 2.598 Speed [1/min]: 1,500 Year of construction: 2001 Weight [kg]: 3.700

Automatic Packing Machine: SIEMENS PLC Controlled, equipped with volumetric cups system. Applicable for the granule packing. Standard Features integrate metering, bag-making, packaging, sealing, printing and counting. Standard positioning with servo film transporting system. Stable for transporting film with two synchronous belts. High automation with auto correction function. Reasonable structure, convenient adjusting operation and maintenance. - Specifications: max. speed of the machine in neutral: 60 cycles/minute | bag size: L(50-230mm), W(50-150mm) | the max width of packing film: 320 mm | thickness of film: 0.04-0.09mm | bag making mode: pillow bag, gusset bag | range of measuring: 150-500ml | air consumption: 0.8Mps 0.25m?/min | power/voltage: 2kW/220V, 50Hz | dimension (LxWxH): 1200?905?1300mm | weight: 300kg | body: SS304 | touch screen SIEMENS, PLC SIEMENS, control valve SIEMEN ...

Machine Details Stock number 1105-037895 Machine type machining center - vertical Brand HURCO Type VMX 40 Year of construction 2000 Control type CNC Storage location FRANCE Country of origin taiwan Delivery time immediately Freight base from site Technical details x-travel 1060 mm y-travel 508 mm z-travel 650 mm Working surface 1200 X 610 mm Motor power (30 min. ED) 15 kW Distance between table and spindle 150 - 760 mm Torque 600 Nm rpm 30 min ED 22 Tool changer 30 times Ultimax 4 Control Machine weight ca. 6 t Information HURCO VMX 40 BORN 2004 CNC ULTIMAX 4 Synchronous.Thread 8000 rpm SPAENEFOERDEREr

technical details generator: - Type: Synchronous - Rated voltage: 230 V - Apparent power at LTP: 4.18 kVA - Active power at LTP (emergency power): 3.8 kW - Apparent power at COP: 3.63 kVA - Active power at COP (continuous power): 3.3 kW - Protection class generator: IP 23 - Version sockets: 2 x 230 V, Schuko - Protection class sockets: IP 44 technical details drive: - Drive: SC170B - Power factor: 0.9 cosφ - Starter: Hand start - Engine oil quantity: 0.25 (min) - 0.6 (max) liters - Fuel: Gasoline - Tank volume: 15 liters - Runtime at 50% load: 14.0 hours - Runtime at 100% load: 9.5 hours - Sound pressure level Lp: 75 dB(A) - Sound power level Lw: 96 dB(A) Dimensions and weight: Length: approx. 595 mm Width/depth: approx. 460 mm Height: approx. 527 mm Weight: approx. 55 kg Scope of delivery: - 1 x wheelset with folding handle (Changes and errors regard ...

STAMFORD Synchronous Generator HVSI 824 F2 2788 KVA 10,500 V 153.3 A 50 Hz, 1500 1/min. Accessories: - 2 sets winding PT100 - AVR MA327, PFC-3 COMPLETELY RECONDITIONED, restored, windings impregnated

STAMFORD Synchronous Generator LVXI 824 H2 3800 KVA 690 V 3197.6 A 50 Hz, 1500 1/min. Accessories: - 2 sets winding PT100 - AVR MA325, PFC-3 COMPLETELY RECONDITIONED, restored, windings impregnated

Combi sheeting machine Second-hand machine - overhauled by a specialist 6 months warranty at call Properties: + mobile combination sheeting machine + Year of construction 1999, workshop overhauled 2023 + suitable for all types of dough for rolling out and touring + equipped with new felt and linen tapes and scrapers + equipped with extendable roll-out table as an extension + all relevant parts have been refelted + with flour container + with trawl net & corrugated mat for beating dough pieces, rolls or breads + with long roll station at the bottom for all doughs for long rolling + Carrier belt for high transport (approx. 83 cm height) of the elongated rolled dough pieces + complete overhaul in our workshop, according to German quality standards + only high-quality original parts are installed + Machine was finally tested by our master baker + comes with instruction  ...

Six ABB 9100kVA (11kV 440V 720rpm 60Hz) synchronous generators plus six Unitrol 1020 AVRs. 2015 year of manufacture. Zero running hours after FAT. Designed and built for an offshore marine vessel, construction of which did not proceed. Necessary mechanical power for driving equipment approx. 7,5MW The following documentation is available and can be provided to interested parties upon request. - Technical specification, GA, and other drawings and documentation - American Bureau of Shipping (ABS) approval documentation - 2015 FAT reports witnessed by ABS - 2021 ABB inspection reports concluding the generators are in good internal condition The equipment is stored in the Vaasa area of Finland and is offered EXW under INCOTERMS 2020 on an as is, where is basis. Arrangements can be made for inspection. Wärtsilä Finland Oy has and can demonstrate clear title to the  ...

BRANDT KDF 660 Profiline single-sided edge banding with joint milling, pre-milling, fine milling, 2-fold corner copying, radius drawing blade, flat-drawing blade and babble units Type: KDF 660 Profiline Specifications: BRANDT KDF 660 Profiline with joints and corner rounds Preheating of the tool stucco IR preheating Edge thickness 0,4 - 15mm Banding height max. 66 mm, with program high adjustment Caps from the roll at 3mm thickness max 45mm height or 0.8 65mm Plate thickness max. 8-60 mm for corner copying max 40mm Control PC20+ link control (loss of contact), with modem for remote service/maintenance 1. Joint unit program Adjustment of the infeed line 2. Bandkapmesser 3a. Radiant heater High-strength bonding by workpiece preheating 3b. Spray anti-adhesive 3c. Quickmelt Glue Mel Mel Application Unit with Quick Change 3d. Leimangabe by means of glue rol ...

Tenoning spindle: 2 St. Number of milling agregates: 7 St. Spindle diameter: 50 mm control: Weinig, PC-Nexus Weinig Unicontrol 12 with radial and axial CNC spindles as well as VARIO table and milling carriage Machine can be seen in use for a short time! Technical data summary (please inquire about any additional accessories included) crosscut saw > Electronic crosscut saw, horizontally infinitely adjustable > Number of tools: 1 piece. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Tool diameter max.: 400 mm > Motor power: 3.7 kW > Laser directional light to detect the saw section > Axial adjustment path 150 mm NC axis, electronically infinitely variable > Radial pneumatic adjustment path 8 positions for e.g. edge rounding from above Rounding aggregate > Position: horizontally below > Motor power: 1.5 kW > Spindle diameter: 20 mm > Tool clamping length: 25 mm > Spindle speed: ...

Diesel Generator 2 x Yanmar 1.25 MW / 50 Hz – 2019 in new condition Two identical medium speed diesel generators made by Japanize Yanmar with complete auxiliaries for Diesel and MDF operation. Equipment was manufactured in year 2019 and it is still in original factory packages, and they have one year factory guarantee. Gensets are rated in continuous operation at 1000 kWe and 1250 kWe in Prime Power operation (one hour in 12 hour period). Engines are 6-cylinder inline, turbo charged 1000 rpm diesel engines, alternators are self-ventilated 400 V brushless type synchronous generators. Engine and alternator are built on common base frame and they have rigid connection. Delivery includes in addition to generating sets control panels, auxiliary motor control panels, fuel oil feeding systems for diesel and MDF, lubrication oil system, radiator cooling system for engines, start air sy ...

AGG 600_SSK0 Achievement: PRP: 600.0 kVA / 480.0 kW / 866 A ESP: 660.0 kVA / 528.0 kW 50 Hz 400 volts Disposals: Terminal strip 3-pole, neutral conductor, grounding. Engine: Scania DC16 093A 02-54 Power: 545.0 kW Cylinders: 8 Cooling water capacity: 68.0 l Oil volume: 48.0 l incl. starter battery 24 volts Generator: Nidec TAL Series 600 kVA 1 Bearing Synchronous generator with AVR voltage regulation, directly with Steel disc clutch flanged to engine. Construction: NEA in soundproof hood with 990 l base frame tank. Control: Comap InteliLite AMF25 automatic emergency power incl. battery charger and cooling water heater, for automatic start in the event of a power failure (without power switching, not synchronizable), with shutdown in case of overtemperature and lack of oil pressure. Digital display of voltage, frequency, operating hours, 3x phase curren ...