sw 3 ha used for sale

General SKU025P753 MakeChemap AG No.9-2964 Year of construction1985 LocationBarneveld Pressure Working pressure3 Bar Vacuum possiblecheck Working pressure jacket3 Bar Vacuum possible jacketcheck Main Features MaterialStainless steel Volume300 Ltr. Specified Features - Stainless Steel Reactor MaterialStainless steel 1.4435 (316L) Stainless Steel Reactors Reactorcheck Capacity300 Ltr. Vessel sizesdia. 700x800mm, Flat top side Dished bottomcheck Outletdia. 30mm With jacketcheck (15 Ltr.) Max. temperature130°.C., Vibro stirrer Information Floorspacedia. 0,9 m Total height2,2 m Extra SpecificationsWithout controls Technical specs Extra informationFlat top sideStainless Steel ReactorsChemapReactors > Stainless Steel ReactorsBrand > Chemap What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping ...

Inlet medium: AP water, outlet medium: distillate, distillate outlet temperature: approx. 99°C, tank volume: 900l, number of preheaters/evaporator columns: 3/4, distillate production: 300l/h, pure steam production: approx. 70kg/h, operating modes: distillate production/pure steam production/WFI loop system sterilization, controls: Siemens SPS S7-300. The distillation unit was designed as part of an overall system but has its own control and automation and can be operated separately. Documentation available. An on-site inspection is possible.

Key data: 75 mm, 30

Single Screw Extruder Cincinnati TALOS 75-30G Output capacity: max. 450 kg/h (depending on material and processing conditions) Screw diameter: 75 mm, L/D = 30 Screw geometry for processing HDPE/PP 11 x Tool Zones incl. TC Type J ITIB 3-pin Thermal Probe incl. mass temperature and pressure sensor Interface for succession via CAN Open Bus Machine control Cincinnati EXcXP-touch Drive power main motor: 125 kW Total connected load: 178 kW Machine weight: 2,200 kg Remark: incl. spare engine (used) without material hopper Condition: used, function tested

Clamping force: 1300kN, screw diameter: 40mm, max. injection pressure: 2120bar, shot volume: 182m³, shot weight: 153g, tie bar spacing: 470mm/470mm, platen dimensions X/Y: 650mm/650mm, min. mold installation height: 275mm, max. opening stroke: 850mm, centering: 125mm. Machine dimensions X/Y/Z: approx. 4600mm/1600mm/2200mm, weight: approx. 5500kg. The clamping unit shows an oil leakage at the clamping cylinder. Documentation available. An on site inspection is possible.

Code: 0228 Brand: OMS SALVARANI Model: 300 INVINCIBILE Pneumatic double croscutting machine for cutting wood, frames, fixtures, joinery, furniture, and various other materials Technical data: Working length mm 3000 Blade diameter mm 300 Motor power Hp 2,5 - Rpm 3000 Manual movement of the 2 heads Cutting from 0 to 45° right and left Pneumatic pedal for lowering the heads N° 2 pneumatic clamps for locking workpieces N° 2 suction ports diameter mm 50 Compressed air 6 bar Overall dimensions mm 4000 x 700 x 1250 h Weight kg 520

Grinding length: 1500mm, center height: 175mm, max. workpiece diameter: 350mm, max. workpiece weight: 300kg, grinding wheel diameter: 450mm, grinding wheel width: 80mm, bore: 203mm. Machine dimensions X/Y/Z: approx. 3600mm/1900mm/1900mm, weight: approx. 4000kg. Documentation available. An on-site inspection is possible.

I am selling an autoclave Korimat KA 380 Programmable control with the ability to record temperatures 1 basket for inserting products Machine in original condition, fully functional. Possibility of transportation and installation of the device by an external service company. Price negotiable.

Watercooled chiller TRANE RTHD 300 SE 1055 kW Cooling capacity: 1055 kW / 299.98 tons (12/7 - 30/35°C) Year of manufacture: 2016 Refrigerant circuit: 1 pcs. Heat exchanger: Shell and tube Compressors: 1 pcs. Trane CHHC1D1F0N0 (screw) Type of refrigerant: R134a Dimensions: 3.3x1.65x2.3 m. Weight: 6300 kg. Working hours: 8319 h. Condition: Good

General SKU315T1252 LocationBarneveld Main Features MaterialStainless steel Volume300 Ltr. Motor1.5 KW Specified Features - Stirring vessel MaterialStainless steel Capacity± 300 Ltr. Vessel sizesdia. 750x690 mm With covercheck Top connectionsdia. 34 mm Outletdia. 46 mm With jacketcheck With paddle stirrercheck Motorcheck 1,5 kW 380-500 Volt Speed mixing shaft10-280 rpm Stirring vessels With paddle stirrercheck Information MakeTerlet Type(unknown: missing typeplate) Mounted on legscheck With switch(as is) Floorspace1,4x1,4 m Total height1,5 m Weight570 kgStirring vesselsTerletStirring vessels > Stirring vesselsBrand > Terlet What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please vis ...

gebr. Cover FP3 NC, built in 1983 in neat condition: Travel X: 400 mm, Y: 400 mm, Z: 400 mm Table size approx. 700 × 460 mm Tool holder SK 40 Spindle motor power typ. 2.0 – 3.0 kW Feed speed approx. 2 – 3,600 mm/min Rapid traverse up to approx. 4,000 mm/min Total weight approx. 1,800 – 2,000 kg Power supply / connection 380 V three-phase current Control Dialog 2

sheet width: 3000 mm plate thickness: 8,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 6,80 t dimensions of the machine ca.: m Motorized backgauge with fine adjustment via handwheel up to 1000 mm Cutting length limiter Sharpened blades The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

General SKU212T478 LocationBarneveld CEcheck Main Features MaterialStainless steel Volume300000 Ltr. Motor30 KW Specified Features - Centrifugal Pump MaterialStainless steel 1.4408 Centrifugal Pumps Pumpcheck Number of pumps:1 Capacity300 m3/h With motor30 kW 380/415 Volt (ABB)(Ex) Inletdia. 150 mm Outletdia. 100 mm Information MakeAPV TypeW-25/200-380 Mach.No.922145040915360000 Floorspace1x0,7 m Total height0,6 m Weight390 kg ATEX compatiblecheckCentrifugal PumpsAPV RosistaPumps > Centrifugal PumpsBrand > APV Rosista What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

Key data: 5 KW, 2860 1/min

Used Grundfos MGE 132SB2-38FF265-B electric motor with frequency converter Power 5.5 KW Voltage 400V, frequency 50Hz., current 12.0A, IP55 Speed 700 to 2860 rpm. With remote control / remote R100. Without pump. Sale only to tradespeople.

General SKU212T485 MakeAPV TypeW-25/200-380 LocationBarneveld Main Features MaterialStainless steel Volume300000 Ltr. Motor30 KW Specified Features - Centrifugal Pump Pumpcheck Number of pumps:1 Capacity300 m³/h With motor30 kW 380-690 Volt (ABB)(Ex) Inletdia. 150 mm Outletdia. 100 mm Centrifugal Pumps MaterialStainless steel 1.4408 Information Floorspace1x0,7 m Total height0,6 m Weight390 kg ATEX compatiblecheckCentrifugal PumpsAPV RosistaPumps > Centrifugal PumpsBrand > APV Rosista What you can expect from Foeth: -- Machine is in working condition -- At a reduced price compared to new -- Ready for shipping to any destination worldwide -- You are welcome to inspect the machine in Barneveld, The Netherlands. Please visit us in Barneveld for many more machines!

This SCHELLING FLM 365.002 panel saw was manufactured in 1995. It features a main saw blade diameter of 400 mm and a scoring saw blade diameter of 200 mm, with a maximum saw blade projection of 80 mm. The machine is capable of processing materials like acrylic and glass-fiber reinforced plastic, with a maximum panel length of 3000 mm and a maximum thickness of 80 mm for acrylic. Consider the opportunity to buy this SCHELLING FLM 365.002 panel saw. Contact us for further details.

Control Fanuc ... 0i - TD Turning diameter ... 500mm Turning length ... 1090mm Inclined bed Spindle bore ... 86mm Number of tools (driven tools) ... 12/12 Axis X ... 300mm Axis Z ... 1200mm Spindle speed ... 10-3500 rpm Axis C ... 0,001° Main engine power ... 15/18.5kW Machine weight ... 6000kg L x W x H ... 4483x1800x1830mm

2 DC 8/32 towers, each with 8 stations, suction feeder, DBM 120 stapling and folding unit, DBM 120T trimmer, stacker System 5000

Motor: 2402 cm³ Motor power: 92 kW Top: Diesel Motor Model: D0FA Length 6750 mm Width 2090 mm Height 2900 mm

Machining sides: 3, workpiece materials: aluminium/steel, travel X: 4000mm, feed rate: 120m/min, A-axis: +/-110°, spindle speed: 18000rpm, tool holder: SK30, tool positions: 8, max. profile dimensions X/Y/Z: 4000mm/250mm/190mm, machine dimensions X/Y/Z: approx. 5750mm/2100mm/2350mm, weight: approx. 4000kg, control: Mecal. Documentation available. On-site inspection is possible.

Inv. Num. : 8749 Type: M2-3120B Producer: FLOW Created: 2011 Parameters: Table dimensions: 2000x3100 mm Spindle power: 6.6 kW

work piece width: 900 mm workpiece height max.: 40 mm feed speeds: mm/min workpiece length: 0 mm Control: total power requirement: 35 kW weight of the machine ca.: 3,7 kg Dimensions (LxWxH): 6,0 x 2,35 x 2,2 0 Sheet metal deburring machine - ESA touch panel - incl. turbo separator - incl. 3m infeed table - Spare belts - Documentation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

CNC lathe Okuma LU 3000 EX-M 2PC-600 Control: OSP-P300L Year of Make: 2017 Turning length: 600 mm Turning diameter: 340 mm Swivel diameter over bed: 580 mm Speed: 50 - 5,000 rpm 2 Tool Turrets A-turret: 12 tool positions (all places driven) B-turret: 8 tool positions Equipment / Accessories: - Chip conveyors - One Touch IGF - Tool monitoring system - Tool measuring device - Reinforced coolant pump 8 bar - 3- Baking Chuck Kitagawa B208

Key data: 500 mm, 400 mm

Roboform 350 + Erowa Robot Compackt 44-Fold Electrode Changer This die-sinking EDM machine offers precise machining with a wide range of features. Details: Year 2006 Travels: X/Y/Z 350 x 250 x 300 mm Minimum power consumption: 5 kVA Maximum electrode weight: 25 kg Accessories: incl. Erowa zero-point clamping system on table WITHOUT electrode holder

2 x injection moulding machines EL - EXIS 200 S incl. Wittmann robot cell for removal and feeding ( No IML ) EL - EXIS 300 S incl. Wittmann robot cell for removal and stacking ( no IML )

Grafisk Maskinfabrik - Slitter Rewinder LS-350 Working width: 350 mm Connection voltage: 400V, working width: 350 mm, Supply voltage: 400V

The 2003 Mazak VTC 300 is a Vertical Traveling Column (VTC) machining center designed for handling long, heavy, or oversized workpieces that might be awkward on a traditional moving-table machine. Find more here - / Contact us at -

Drilling diameter: 3-25mm, drilling depth: 1000mm, connected load: 36kW, control: EST, 99 drilling memory positions per program, grinding and coordinate programming, plain text programming via input mask. Accessories: paper band filter, coolant cooling system, 4-door control cabinet, high-pressure pump up to 150bar, oil tank, 1 steady rest for smaller diameters at large drilling depths, direction-adjustable holder for drill bushing holders, various drill bushing holders, long clamping table for 0-height, tailstock stop and base plate for machine vice freely movable on the additional table, matching precision machine vice optionally available. Speed, high pressure, Z-axis (feed), X/Y-axes, and W-axis (approach slide) programmable via control. CPU and card rack defective (fan fault), machine therefore not operational, drives and guideways were fully functional until last operation. An on-s ...

roll diameter: 315 mm throat: 295 mm workpiece height: 190 mm Motor Capacity: 0,37/0,8 kW table-size: 470 x 450 mm saw band length: 2220 mm cutting speeds: 450 + 900 m/min weight of the machine ca.: 110 kg dimensions of the machine ca.: 640 x 510 x 1600 mm Electric 380 Volt: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

1 Wagner Leopard 3570 airless sprayer with air piston drive. It is for hanging on the wall. About 8m of spray hose are included, and a gun with nozzles, filters, etc. For data see type plate Technical data: Gear ratio: 35:1 Max. air inlet pressure: 7.1 bar Max. working pressure: 250 bar Volume flow rate per double stroke: 70 cm³ Max. stroke rate: 60 DH/min Max. flow rate: 4.2 l/min The system was in operation until recently, is well maintained and perfectly cleaned. Pick-up only in 27404 Zeven.

- technically efficient, ready to work – after full service - drilling for the bottom hinge - automatic screwdriver + ASS 60 screw feeder - punch holder - centring system - steering stop for trimming the stay - tilting table - shelf

Tetra Pak TBA19 330 ml Prisma Filling Line General Information: - Manufacturer: Tetra Pak - Model: TBA 19 – Version 010V - Year of Make: 2003 - Capacity: 6,000 packs/hour - Filling Volume: 330 ml - Format: Prisma - Condition: Very good used condition Line Overview: Complete Tetra Pak filling and secondary packaging line for 330 ml Prisma carton packs, designed for reliable and efficient production in dairy and beverage applications. The line combines a proven Tetra Pak TBA19 filling machine with a brand-new cap applicator and a cardboard packer, ensuring modern functionality and high operational reliability. Ideal for producers looking for a cost-efficient, ready-to-install solution with upgraded components. Main Components: - 1. Filling Machine - Make: Tetra Pak - Model: TBA 19 – Version 010V - Capacity: 6,000 p/h - Volume: 330 ml - Format: Prisma ...

CNC lathe Type: GA-360 LM Manufacturer: Goodway Year: 2005 Control: Fanuc Series Oi-TC Max turning diameter: 500 mm Max turning length: 1200 mm Clamping head: 100 mm Swing over bed: 700 mm Spindle bore: 75-105 mm Chuck size: 15" LM driven tools with milling function (C-axis) Driven tool motor: 7 hp Spindle motor: 30 hp Revolver head: 12 VDI 3-jaw chuck Chip conveyor Tailstock Machine in good condition, under power Find more here - / Contact us at -

Trumpf TrumaBend V230 8 assen: Y1 / Y2 / X / R / Z1 / Z2 / V / W bovenste en onderste Willa hydraulische gereedschappen met Trumpf ACB-optie; hoekmeetsysteem 3 beweegbare plaatsteunen aan de voorzijde veel gereedschappen inbegrepen Capacity: 230 ton x 3100 mm Backgauge: CNC Control: Delem Passage between uprights: 2690 mm Max stroke: 365 mm Max distance between table -- ram: 535 mm Depth of throat: 410 mm Table width: 200 mm Locking speed: 200 mm/sec Working speed: 1 > 10 mm/sec Returning speed: 135 mm/sec Electric motor (power): 30 kW Length: 3660 mm Depth: 2120 mm Height: 3095 mm Weight: 17,7 ton

BILLION HERCULES H2000 Series - 320 T Clamping force: 320 T - 3200 KN Injection unit: H 2000 Screw diameter: 75 mm Distance between columns: 610 x 610 mm Tray dimensions: 920 x 920 mm Min/max thickness of the mould: 330 - 680 mm Opening stroke: 660 mm Injected volume: 1259 cm3 Material pressure: 1587 bar Dimensions: 7.1x 2.1 x 2.6 m Weight: 14,000 kg

diameter: 315 mm bore: 89 mm dimensions of the machine ca.: m Wedge bar chuck with short taper DIN 55027 / Gr. 8, for 4 studs, 1 set Baking, studs not available. Machine dealer with own stock of 1600 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

This HONESS V250-3000 was manufactured in 2002. A profile punching machine for tubes and profiles, it features a self-centering product clamp and interchangeable clamping jaws for various tube types. It can handle tubes up to 100 mm wide and 80 mm high, with a maximum punching diameter of 40 mm. Ideal for high-speed punching with a carriage travel speed of 40 m/min. Contact us for more information about this machine.

USED TETRA PAK TBA 19 250ML BASE 30v FILLING LINE FOR SALE Item #: Usm-234 Category Tetra Pak TBA 19 One used Tetra Pak tba 19 250ml base filling line for sale. 1-TBA 19 250ml Base filling line, year of manufacturing 2007, Version 30v, working hours 11900 2-Straw applicator tsa 21 3-tetra pal shrink tts 51 4-20m Tetra Pak conveyors and easy ride 5-Paper trolly Condition: Good

REFURBISHED TETRA PAK TBA 19 200ML SLIM 30v FILLING LINE FOR SALE Item #: Usm-237 Category Tetra Pak TBA 19 Refurbished TBA 19 200ml Slim 30v Filling Line for sale 1-TBA 19 200ml Slim Filling Machine, Year of manufacturing 2007, Version 30v, Working hours 30000 2-Straw applicator TSA 21 3-Multi Shrink wrapper 65 4-20meter conveyors and Paper trolly Condition: refurbished and test run approved.

Box and Bag Printing Machine – BM300 Perfect for printing on paper bags and cardboard. Introducing the BM 300, an easy-to-use and highly versatile digital solution for Direct-to- Packaging printing. With a small investment, it opens up opportunities in the ever-growing market of customizing boxes, shipping envelopes, paper bags, and jute in small and medium runs. This latest addition is a natural evolution based on sales successes and customer feedback, resulting in a more effective and smooth workflow management system. The BM 300 incredible versatility comes from its combination of an ultra-fast HP Technology print engine with water-based, solvent-free, and odorless pigmented inks. It can print on both treated and untreated paper and cardboard substrates, as well as directly on packaging up to 15 cm thick. With the BM 300 Software, you can accurately adjust the printhead  ...

Height 1940 mm Width 1100 mm Length 2200 mm Electrical Supply: 400V 50Hz 3N Total power 22 kW Main Material Stainless Steel, Acid Resistant No loading, possibility to buy additional pole loading for the machine Throat diameter 180 mm Wolf type Straight wolf Auger Stuffing Feeding System Hopper Throat Workmanship Stainless Steel Material of the feeding screw Stainless steel, acid-resistant

sheet width: 3000 mm plate thickness: 4 mm work height max.: 900 mm : 450 mm total power requirement: 5,5 kW weight of the machine ca.: 4800 kg dimensions of the machine ca.: 4250 x 1500 x 1850 mm Equipment: - electric bending angle adjustment - electric upper beam adjustment - foot switch - operating instructions The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Metal band saw MEBA 320 DG semi-automatic hydraulic - Semi-automatic - Hydraulic operation - Infinitely adjustable band saw speed - Mitre cuts possible - Hydraulic clamping of the mitre adjustment - Hydraulically adjustable saw pressure - Fully hydraulic material clamping - Coolant device - Automatic shut-off - Emergency stop - Connection: 400 V - Cutting range: Round material: up to Ø 320 mm

VOEST DA 360 - Lead & Pull Spindle Lathe -Heidenhain digital display -Peak height above bed 400mm -Turning diameter over bed 800mm -Turning diameter over support 500mm -Turning length 1000mm -Rod passage approx. 87mm -Speed range 14 - 1000 rpm / 18x speeds -Automatic length / face feeds -Automatic input Z-axis -Tailstock MK 5 -Wedge bar chuck 250mm -Multifix base holder with insert -Work light -Machine feet -Documentation Dimensions: LxWxH 3x1.5x1.7 meters / Weight 3500 KG

Technical data for the shelf: Shelving system: Meta Type: Clip The scope of delivery includes: 01x Shelf, used Soil name: MS150-III Material colour: sendzimir galvanised Dimensions: 1,300 x 600 x 40 mm Weight: 5.11 kg|pcs. max. load per shelf 150 kg with evenly distributed load Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. An additional desired transport or a shipment of this item is associated with additional costs, which will be charged separately depending on the delivery location or scope of delivery.

Key data: 3500 mm, 12 mm

Schäfer SVRM 3500/12 - CNC 4-roll bending machine - Siemens CNC control with joystick for roller positioning and digital display (renewed in 2006) - Hydraulic tilting of the upper roller by control panel - Rollers made of quenched and tempered material with a strength of 900 N/mm² - Year of construction 1989 Technical data - Max. sheet width: 3500 mm - Bale length of rollers: 3550 mm - Max. sheet thickness bending: 12 mm - Max. sheet thickness bending 4xS/3xS: 8 / 6 mm - Max. insertion limit of the sheets at 20% work hardening: 380 N/mm² - Upper and lower roller diameter: 360 mm - Side roller diameter: 290 mm - Smallest radius to be achieved: 220 mm - Feed speed lower roller: 200 mm/min - Feed speed side rollers: 700 mm/min - Total installed capacity: 22 kW - electr. Control: 380 V / 50 Hz / 3 Ph - Machine weight: 21100 kg

Technical features: heated knives, weld bead limitation 0.2mm, optimization of the welding result through the parallel sliding welding process, individual adjustment of the welding parameters, quick changing of the outer contour allowances by means of holding magnets. Air consumption at 6bar: 15l/Takt, angle adjustment range: 30-180°, profile height: 30-105mm, max. profile width at 90°: 157mm, compressed air connection: 8.7bar, power: 2.7kW, supply voltage: 220V, 50/60Hz, length: 770mm, width: 880mm, height: 1560mm, weight: 320kg. An inspection on site is possible.

no missing parts, no damages - well maintained

spindle diameter: 1 mm x-travel: 1 mm y-travel: 1 mm total power requirement: 1 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Digital color printing system Type: Xeikon 3300 Manufacturer: Xeikon Year: 2013 X 5 colors CMYK+W Second fuser unit alpine for embrossed labels In good condition, fully functional Find more here - / Contact us at -

B&A REF: 9269 TON: 60 SCREW DIAMETER: 25MM SHOT WEIGHT: 45 STROKE VOLUME: 49CM3 INJECTION PRESSURE: 2240AR PLATEN SIZES: 446 X 446MM DBTB: 320 X 320MM MIN MOULD HEIGHT: 200MM MOULD OPENING STROKE: 350MM MAX DAYLIGHT: 550MM EJECTOR STROKE: 125MM AIR VALVES: 1 MOTOR: 11 HEATING CAPACITY: 4.9KW SCREW DRIVE: HYDRAULIC