128,858 used machines on RESALE, but how to find them? Machine Search
Blow volume 0.2-2.0 ltr. PET stretch blower, 3 blow stations, capacity: up to approx. 3,600 bottles / h. Incl. preform bunker, lift and sorter, Available at extra cost: compressor, cooler and moulds
Gearbox due to re-motorization PTO drive shaft is inclusive Reduction 4,987:1
Pump Manufacturer: Lowara (Italy) Type: HTS 32-125 N°: 90 Power: 3 kW Flow rate: 12-33 m3/h at 26-18.8 m height (water) LWH: 600 x 300 x 360 mm
with vertical matrix connector Max. work-piece diameter: 140 mm Max. diameter of upset flange: 180 mm Nominal force of upset slide: 12500 kN Force on clamping slide with dies closed: 12500 kN Stroke of: -Upset slide: 460 mm -Upset slide after closing of dies: 310 mm Number of continuous slide strokes per minute: at least 32 Electric motor power: 75 kW Machine dimensions: -Length: 8035 mm -Width: 4800 mm -Height: 3575 mm Machine weight: 140 tons
Capacity, ton 1250 Stroke, mm 500 Min number of no-load stroke: 8 /per min Slider adjustment, mm 215 Max. shut height between bolster plate and slider (stroke down, adjustment up), mm 860 Table size, mm 1600 x 1850 Slider size, mm 1300 x 1400 Table gap size, mm 1100 x 1100 Distance between columns, mm 1630 Distance between slides, mm 1580 Cushion travel, mm 200 Cushion capacity, ton 200 main motor power, kW 90 Press weight, kg 130000
Koch Pumpentechnik (Porta Westphalica) Built: 2007 Type: FP2/40-125/302 Power: 20 m3/h at 18 m height (water) very good condition Engine power: 3 kW/3.45 kW Weight: 70 kg Diameter inlet: 65 mm Diameter outlet: 50 mm Milk pipe LWH: 500 x 230 x 360 mm
Spiral kneader Diosna Oasis SPK 200 E with emptying of the soil -Spiral kneader with center emptying -Stainless steel boiler and tool -for max. 200 kg dough
Key data: 100 KW, 125 kVA, 400 V
MODEL: EQ-D125100 ENGINE: Deutz BF4M1013FC FREQUENCY (HZ): 50 VOLTAGE (V): 400 MAXIMUM POWER: 125(kVA) / 100(kW) STARTING: ELECTRIC CONTROL SYSTEM: SELF-CONTROL FUEL TYPE: DIESEL COOLING: WATER-COOLED WEIGHT: 1900kg DIMENSIONS L/W/HEIGHT (MM): 280011501600 The engines are new, complete including control, diesel tank, exhaust and batteries. Network monitoring, grid feed-in Soundproofed Immediately ready for use. Control: Deep Sea Electronics (DSE) / ComAp Alternator: Leroy-Somer / Stamford Additional: Automatic Transfer Switch (ATS) 63A/100A ABB & Schneider Disconnectors GenCloud Connect with a phone or computer Single-phase valve 50°C-55°C Radiator External Diesel Tank Lubricating Oil Heater Water Heating Dispatch: Worldwide transport including unloading is possible for an extra charge To be able to quote an exact freight price, please send us an inquiry wit ...
Slideways for die-casting machine, 2580 x 125 x 25mm, Idra, Oleopress, new The new slideways from Olepress / OP die casting come from a spare parts stock of an aluminium die casting company. They fit die casting machines like Olepress, Idra and others. See dimensions Slideways, slide rails for aluminium die casting machines, case hardened steel. The bronze bars of the die casting tables slide on these slide rails. 2580 x 125 x 25mm, bores 4 x D20/14 x 2540 x 90 If you have a UID number, we will gladly issue an invoice without VAT. You are welcome to inspect and check the goods at our premises in Austria, 3130 Herzogenburg.
Manufacturer Düchting Type centrifugal pump LHK 125x5 Unused / Refurbished Flow rate 180 m3/h Head 150m Step number 5 Weight approx. 550kg Special price
used
Qty. 1 Second-hand complete 12-Hi reversing cold rolling mill incl. sand blast line Mfc.: Kobelco Type: 12-Hi reversing Built: 1986 Strip width: 900 – 1250 mm Thickness: Entry: 3.2 mm Exit: 0.4 mm Rolling speed: 120/300 m/min.
; Gross weight [kg]: 7753; Engine: Perkins 4008-30TAG3; Accessories: Battery, Control Panel, Including : coolant heater and battery charger
Weibert RLA 125 Clean air extraction system Rated volume flow: 1095 m3/h Minimum volume flow: 884 m3/h Max Vacuum: 2220 Pa Chip collection volume max.: 255 ltr. Engine power: 2.2kW Connection 50Hz: 400V Weight: 194 kg Dimensions in mm: 1100 x 830 x 1650 Suction nozzle diameter: 125 mm Height lower edge suction nozzle to the ground: 850 mm Max sound pressure level 73 db (A) G&STÜ-5131250
General- Compound slides with turning/milling spindle as integrated spindle motor, with hydr. locking at turning acceptance HSK-63A DIN 69893 - Y-axis ± 125 mm - B-axis ±120° with pneumatic locking - Tools magazin disc with 1x24 positions - Absolute direct gauging system in the X, Y, Z linear axes - Coolant pump 12 bar; 23l/min - Cooling system for spindle motor, turning/milling spindle, B-axis torque motor; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways500 mmMax. Turning Length1200 mmBar diameter max.65 mmTurning diameter500 mmWork spindle (left)Diametre of spindle nose170h5 mmSpindle noseFlat flange Spindle bore87 mmSpindle diametre on front bearing130 mmMain drive 1Drive power (100% DC)25 kWDrive power (40% DC)32 kWSpeed range- 5000 rpmTorque (100% DC)280 NmMax. torque (40% DC)360 NmTurning-milling spindleSpindle taperHSK-A 63 DIN 69893 ...
Key data: 250 mm, 550 mm, 145 mm
Demonstration article Condition: Mint The Superturn 550/125 Vario with MFB 16 Vario offers modern turning, milling and drilling technology for the central machining of small to medium-sized workpieces - a practical all-rounder for mechanics and model makers, vocational schools and training workshops. The basic component SUPERTURN 550/125 Vario is a lead screw lathe with an infinitely adjustable speed control and a digital speed display. The maximum turning size above the carriage is Ø 145 x 550 mm, the spindle bore diameter is 26 mm. Standard equipment: - Digital speed display - Three-jaw lathe chuck ø 125 mm, centr. - Centrifuge MK 4 - Grain tip MK 2 - Emergency stop button / zero-voltage trigger - Lathe chuck protection with safety limit switch - Chip tray / bulkhead - Toolbox / Instruction Manual / CE Specifications: Center width 550 mm Tip height 125 mm ...
Description: 12 New Transformers Design : Cast resin transformer Design: Dry Make : TESAR Built: 2012 Condition: New Rated power: 1250 KVA Medium voltage: 20 KV +- 2 x 2.5% Low Voltage: 270 V Solar Transformers Vueuqq Switching group: DYN 5 Frequency: 50 Hz Cooling type :AN Total weight: 3450 Kg Other sizes and voltages also available from 100 KVA to 3500 kva . All transformers are tested and ready for use and immediately available from our warehouse in 59557 LIPPSTADT . Nationwide delivery included. For further questions, contact i.m. Mon to Sat 8 a.m. to 10 p.m.
Plug 1 – 1250 kVA Transformer Manufacturer: France Transfo / Schneider Electric Year: 2002 Power: 1250 kVA HV voltage: 5775/5500/5225 V LV voltage: 410 V LV Current: 1760.2 A Cooling: ONAN Insulation: OIL Winding: ALU Total weight: 2665 kg Condition: Good condition sold as is, with no warranty. Plug 2 – 1600 kVA Transformer Manufacturer: Pauwels France Year: 2004 Power: 1600 kVA HV voltage: 5750/5500/5225 V LV voltage : 2253.07 V LV Current: 167.96 A Cooling: ONAN Insulation: OIL Winding: Total mass: 3200 kg Condition: Good condition, sold as is, no warranty. Plug 3 – 1250 kVA Transformer Manufacturer: France Transfo / Schneider Electric Year: 2004 Power: 1250 kVA HV voltage: 5775/5637/5500/5362/5225 V LV voltage: 410 V LV Current: 1760.2 A Cooling: ONAN Insulation: OIL Winding: ALU ...
Code 71112 Description Radial drilling machine Make SORALUCE Modell TRO - 1250 Serial No. 2754 10406 Year 1975 Capacity in Steel 60 40 mm Capacity in Cast Iron 50 mm Thread cutting in Steel 60 M 30 Thread cutting in Cast Iron M 40 Spindle taper 5 MC Spindle radius: max / min 1400 / 450 mm Spindle traverse 950 mm Min / Max height spindle / top of base plate 300 – 1300 mm Arm traverse 700 mm Quill stroke 300 mm Number of speeds 12 Spindle speed range 25 – 1440 rpm Number of spindle feeds 6 Spindle feed range 0,08 – 0,99 mm/rev Baseplate size 1900 x 750 mm Clampsurface base plate 1200 x 650 mm Main motor 3,0 kW - 380 Volts Dimension of machine 2000 x 750 x 2150 ( max.2650 ) mm ( L x W x H ) Weight 2500 kg Accessoiries Box 600 x 450 x 400 mm Coolant elect ...
Ø plateau: 1250 mm Top speed: 500 rpm - 2 ranges Ø false plateau: 1450 mm Maximum piece: 1550 mm Maximum height of the piece: 1200 mm RAM stroke: 800 mm Crossbar stroke: 850 mm Tool warehouse: 10 ATC CNC Siemens 810 D
honing diameter: 125 mm stroke: 350 mm throat: mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Two step expansion for pre and finish honing Air gauge measuring Fixture for honing a 4 cylinder block Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
General- Compound slides with turning/milling spindle as integrated spindle motor, with hydr. locking at turning acceptance HSK-63A DIN 69893 - Y-axis ± 125 mm - B-axis ±120° with pneumatic locking - Absolute direct gauging system in the X, Y, Z linear axes - Coolant pump 12 bar; 23l/min - Cooling system for spindle motor, turning/milling spindle, B-axis torque motor; Control: CELOS with Siemens 840D sl Operate Working areaTurning diameter500 mmSwing diameter over guide ways500 mmMax. Turning Length1200 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmMain drive 1Drive power (100% DC)25 kWDrive power (40% DC)32 kWSpeed range- 5000 rpmTorque (100% DC)280 NmMax. torque (40% DC)360 NmTurning-milling spindleSpindle taperHSK-A 63 DIN 69893 Spindle speed-12000 rpmDrive power (100% ...
General- Compound slides with turning/milling spindle as integrated spindle motor, with hydr. locking at turning acceptance HSK-63A DIN 69893 - Y-axis ± 125 mm - B-axis ±120° with pneumatic locking - Absolute direct gauging system in the X, Y, Z linear axes - Coolant pump 12 bar; 23l/min - Cooling system for spindle motor, turning/milling spindle, B-axis torque motor; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways500 mmTurning diameter500 mmMax. Turning Length1200 mmBar diameter max.65 mmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmMain drive 1Drive power (100% DC)25 kWDrive power (40% DC)32 kWSpeed range- 5000 rpmTorque (100% DC)280 NmMax. torque (40% DC)360 NmTurning-milling spindleSpindle taperHSK-A 63 DIN 69893 Spindle speed-12000 rpmDrive power (100% ...
General- Compound slides with turning/milling spindle as integrated spindle motor, with hydr. locking at turning acceptance HSK-63A DIN 69893 - Y-axis ± 125 mm - B-axis ±120° with pneumatic locking - Tools magazin disc with 1x24 positions - Absolute direct gauging system in the X, Y, Z linear axes - Coolant pump 12 bar; 23l/min - Cooling system for spindle motor, turning/milling spindle, B-axis torque motor; Control: CELOS with Siemens 840D sl Operate Working areaSwing diameter over guide ways500 mmMax. Turning Length1200 mmTurning diameter500 mmBar diameter max.65 mmMain drive 1Drive power (100% DC)25 kWDrive power (40% DC)32 kWSpeed range- 5000 rpmTorque (100% DC)280 NmMax. torque (40% DC)360 NmWork spindle (left)Spindle noseFlat flange Diametre of spindle nose170h5 mmSpindle bore87 mmSpindle diametre on front bearing130 mmTurning-milling spindleSpindle taperHSK-A 63 DIN 69893 ...
plate thickness: 1,25 mm roll-body distance: 250 mm throat: 260 mm distance between roll centers: 62 mm tool adaptor: 26 mm speed: 6,3 m/min total power requirement: 0,7 kW weight: 170 kg range L-W-H: 1020x600x1500 mm Domestic equipments: - motor driven beading machine - 5 sets of bead rollers - Footswitch - Operating instructions in German - CE mark / Declaration of Conformity The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
width of the strips: 25 mm band length: 762 mm dimensions of grinding wheel: 125 mm Table tiltable up to: 45 Grad table surface area: 130 x 130 mm connected load frequency: 230 V total power requirement: 0,3 kW weight of the machine ca.: 9 Kg dimensions of the machine ca.: 650 x 360 x 400 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Mechanical/mechanical clamping system with force transmission, manually operated: mechanical/hydraulic clamping system · Deformation-resistant design for very high clamping accuracy · for use on machining centers with high quality and production performance · Drive spindle with clamping force presetting · grease fittings on both sides for lubricating all guides subject to wear and the spindle thread · Mounting thread M12 for workpiece stop · Stable chip protection prevents chips from penetrating the interior of the body · all guides hardened and ground · Height measurement of base body/workpiece support -0.02 · important for paired use · Supplied with step jaws reversible, hardened and ground. Other technical features: · Version: Model RKE - 3-sided clamping option · Can be clamped horizontally, vertically or laterally - Base body made of steel - hardened and ground - with fo ...
weight max. in kg: 1250 kg Working height minimal: 540 mm Working height maximum: 1120 mm table diameter: 800 mm swivelling range: --> 95 Grad max. torque: 490 Nm table rotation speed: 2 U/min Working height from to: 540 - 1120 vertikal mm Working height from to: 700 - 1280 horiz. mm total power requirement: 2,53 kW weight of the machine ca.: 757 kg dimensions of the machine ca.: 1,76 x 1,63 m Hydraulic positioner for permanent turning right + left, tilting, Raise and lower. Machine dealer with own stock of 2500 m². The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
centre height: 125 mm spindle bore: 27 mm taper in dividing head spindle: MK 4 mm total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: m Horizontal dividing head WALTER mounted on a SINUS-table WELK. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
angle steel/side length: siehe TD mm double T-iron on the x-axis: siehe TD mm U-iron on the x-axis: siehe TD mm total power requirement: 15 kW weight of the machine ca.: 4,6 t dimensions of the machine ca.: 1850 x 1550 x 1685mm m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
The machine is in good technical condition, after prior agreement it is possible to test it. General repair including major modernization (retrofix) on CNC control including automatic central lubrication of axes + hydraulic systems, water cooling, conductive rollers with brushes for the system of possible welding of the workpiece and complete covering against chip flying. Swing diameter: above the bed 1250mm above the slide 900mm Control system: Heidenhain manual plus 4110 Max. workpiece weight: 14,000Kg Max. workpiece length: 3,000mm Machine weight: 16,350Kg Machine power: 80 Kw Machine dimensions: width 3000mm height 2100mm length 8000mm Supplied accessories: Face plate including handles, support (steady rest), raised cutter head, universal chuck, etc.
turning diameter over slide rest: 940 mm turning length: 10000 mm turning diameter: 1250 mm spindle diameter: 105 mm speed: 1,6 - 315 (x24) m/min voltage: 380 V total power requirement: 75 kW weight of the machine ca.: t dimensions of the machine ca.: m 4-jaw faceplate Power compound The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Notching cutter Wegoma Type: AKF 125 for milling plastic and aluminium profiles with profile stop on both sides swivel 60° Pneumatic clamping device Manual feed with hand lever of the three-phase milling motor Engine start directly at the hand lever Suction nozzle with a diameter of 100 mm running on the milling carriage Profile stop adjustable without tools with locking bolt for 90° and 45° on both sides Power milling motor 1.5 kW Speed milling motor 2800 rpm Milling path max. 380 mm Milling cutter diameter/height max. 210 mm/ 90 mm Milling spindle diameter 27 mm Dimensions: L 700 mm x W 500 mm x H 700 mm Weight approx. 50 kg
saw blade diameter: 1250 mm cutting diameter: 380 mm cutting range: 480x320 mm motor speeds:: 3000 U/min feed speeds: 1000 mm/min main drive motor: 112 kW chip conveyor: cutting speed: 10-265 m/min total power requirement: 125 kW weight of the machine ca.: t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Head type: 3-SH/60-125-PE/T (DeCo) Marke/ Brand: UES Condition: New/ New Layers : 2 Center distance: 125 mm Nozzle/ Die: 60 mm Hoses/ Parisons: 3 Material/ Material: HD(PE), PP WBK/ WTC: Yes/ Yes View stripe: No/ No
New and unused 2023 generator set with 0 running hours.; Gross weight [kg]: 7753; Engine: Perkins 4008-30TAG3; Accessories: Battery, Control Panel, Including : coolant heater and battery charger
Rated current (A): 1250, Poles: 3; Gross weight [kg]: 41; Accessories: Multiple breakers in stock!, NEW/UNUSED
; Gross weight [kg]: 7970; Engine: Perkins 4008TAG3; Accessories: Tanker, Battery, Control Panel, Including : coolant heater and battery charger; Water Tank Volume [l]: 1450
Head type: 2-BKD-51-125 (A 70) Marke/ Brand: Bekum Overhauled: Yes/ Yes Layers : 1 Center-distance: 125 mm Nozzle/ Die: 51 mm Hoses/ Parisons: 2 Material/ Material: HD(PE), PP WBK/ WTC: Yes/ Yes View stripe: No/ No
Prism jaw, 125mm wide for clamping round parts, type 1, D4-20mm, and 2x D6-40mm, Type 2, D4-20mm and D9-62mm
maximum number of results exceeded
please refine your search
.jpg)
