studer e used for sale

Make: Allweiler Type: SZBP 100.1 E 11 P01 No.: 7602467 Q = 5-25 l / min = 300-1500 l / h n = 40-140 min-1 Year of construction: 1995 Condition very good Spare parts: 1 stator speed-controlled drive North Type: SK255F AL-R1500-100 L / 4E Dimensions: LWH = 1400x300x650mm Weight: approx. 120 kg

tower silos 4 x 50 m³ / 50000 litres of polyester tanks / Tower silos / flour silos, GRP silos, grain silo / hopper silo / compound feed component silo Top condition Content per silo: 50 m³ / 50000 litres piece / pc: 4 pieces Year of construction: 1994 mass of Tower silos without steel: approx. Ø 2,80 x 12 m high Height of the entire system: 21 m Density/weight: 1,200 kg per m³ approval number: Z 10-22-42 Manufacturer: Polem More details: the silos are in good used condition. According to the age traces are present. The system has complete works until its closure. The system could not be tested yet, because there is no power supply. It is a complete meal silo plant with very thick-walled 4 x 50 m³ GRP silos with a density/weight 1200 kg per m³ is each silo separately to fill up the tanks through several cross conveyor (scraper conveyors). The silo is a spray head to cle ...

Chain hoist with motorized chassis for steel beams, load capacity: 1,000 kg, lifting speeds: 5.4 m/min. (fast); 1.4 m/min. (slow), incl. hallway operation, without steel beams. Brakes and drives workshop overhauled / tested.

Francis Shaw 90mm coldfeed rubber extruder.Year: 1992. Machine No.4846Vented. Side power roller feed,L/D ratio 20:1,H series David Brown gearbox,Thrige Scott 63kW, 2000rpm DC variable speed motor.Machine fully overhauled, cleaned/painted and fitted with NEW electrical control panel. With provision for 5 x TCU's.

Drum pump, hygienic ExzenterschneckenpumpeVon of the company GrünpumpenTechnische DatenTyp ds.: LDS 80.1Ser. No.: 0259 Qm³ / h 2,40N1 / min: möglichVerpackung 6,75ZahlungsmodalitätenBarzahlung pick up and transfer in advance and shipping pick up, shipping via forwarding and abroad by prior arrangement all data were listed to the best of our knowledge and belief.Errors are reserved. This auction is aimed only at professionals, dealers, and other legal persons.

Rated power up to 300 kg/h engine power Drive motor 0.37 (0.5) Washing machine motor 0.12 (0.16) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 1280 mm width 870 mm He he 1350 mm 65 mm width 350 mm Band length 4900 mm application width 240 mm Application shoehe 0-50 (infinite) mm Weight 350 kg Material 1.4301 / AISI 304 Juice yield up to 75% Band speed 2 m/min Contact time 1 min Water consumption for cleaning 2 l/ min Connection for waste water 48.3mm Connection for juice drain 1 High juice drain 420 mm High sewage drain 120 mm Hoehe marc ejection 700 mm ; New machine - best condition

Rated power up to 3000 kg/h engine power Drive motor 2.2 (3.0) Washing machine motor 0.37 (0.5) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 3035 mm width 2080 mm He he 1690 mm Width 1200 mm Band length 9950 mm application width 900 mm application shoehe 0-65 (5 steps) mm Weight 2500 kg material 1.4301 / AISI 304 Juice yield up to 75% Band speed 0.5-3.5 m/min Contact time 2-11 min Water consumption for Cleaning 6 l/min Connection for waste water 76.1mm Connection for juice drain 11.2 High-gasning 400 mm High-speed wastewater drain 250 mm Hoehe marc ejection 880 mm Supplied high-pressure cleaner, compressor ; New machine - best condition

Rated power up to 1500 kg/h engine power drive motor 0.55 (0.75) washing machine motor 0.12 (0.16) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 2538 mm width 1463 mm He 1460 mm mm width 650 mm Band length 8120 mm application width 450 mm application shoehe 0-50 (infinite) mm Weight 1060 kg material 1.4301 / AISI 304 Juice yield up to 75% Band speed 0.9 - 1.8 m/min Contact time 1.9 - 3.8 min Water consumption for cleaning 3 l/min Connection for waste water 75mm Connection for juice drain 2 High juice drain 400 mm Hoehe wastewater drain 210 mm Hoehe marc ejection 840 mm Supplied high pressure cleaner, compressor ; New machine - best condition

End clamp profile Schletter GmbH, solar mounting systems Type 7231526 EC06 Dimensions: L 70mm, B 30mm, H 20mm Price per piece 0.50 approx. 2,300 STK. in stock.

Rated power: up to 1000 kg/h engine power: engine: 0.75 kW buster cleaning: 0.37 kW high pressure cleaner: 4.7 kW Electrical connection: 400V 50Hz (3 phases) Electrical fuse: 16 A Dimensions: Laenge: 2 145 mm Width: 1 270 mmhoe height: 1 290 mm d drop-off height: 1 290 mm Width: 580 mm Application width: 240 - 460 mm application shoehe (9 steps): 10 - 50 mm Weight: 665 kg Material: 1.4301 / AISI 304 Juice yield: up to 75% band speed (infinite): 2.1 - 5.5 m/min Throughltime: 0.6 - 1.6 min Water consumption for cleaning: 3 l/min Connection: Connection for waste water: DN75 Connection for juice drain: 1 1/2 He juice drain: 305 mm High water flow: 86 mm High disarmer discharge: 745 mm usable for core and stone fruit Supplied New machine - best condition

Force of pressure: 75 t projection: 300 mm table size: 620 x 800 mm Durchfalloch in the table: 225 x 325 mm table adjustment: 175 mm plunger surface: 180 x 475 mm slide adjustment: 80 mm stroke adjustment: 16-140 mm stroke rate: 90 / min drive motor: 380 V, 3 kW space: 1700 x 1200 x 2500 mm weight: 3300 kg

Iddon HRX 4.5? (120mm) Cold Feed Rubber Extruder Year 1994 LD ratio 17:1 Bostock & Bramley Gearbox ABB Motor: 1994, 95kW, 1870 rpm, 419 amps, 360 volts With 1 x spare vacuum screw With Control Panel

Key data: 30 , 28 , 110

Single-screw extruder with new 7,5kW drive, new gear box, new cylinder and new screw 30 mm - 28 d, nitrated new ceramic heating elements, cooling fan, temperature sensors Control cabinet integrated in the machine frame Machine frame on wheels Stainless steel hopper

Key data: 30 , 28 , 110

Plant for the production of filament for use in 3D printers Capacity up to 10 kg/h consisting of 30 mm extruder, stainless steel trough, puller and winder with traverse guide

Thank you for your interest in our gum extruder system we offer you as follows: many thanks for your interest on our new chewing gum extruder plant, please follow our offer find: AUTOMATIC EXTRUDING; ROLLING AND SCORING MACHINE 7 ´ ´ /. COMPLETE LINE for production of chewing gum sticks and Chiclets Manufacturer: WLS Type: Chewing gum Extrudier-, rolling and cutting machine gum extruder, rolling and cutting system Product: Chewing gum sticks and Chiclets Size (working width): 7 ´ ´ / 177mm other dimensions are possible on demand Type: WLS RAS 7 "with manual take-off Capacity: Approx stick gum. 200-250 kg / h / Chiclets approx. 250-350 kg / h Number of rolling stations: 4 Number of cutting stations: 2 Electrical: 400V 3 ph 7 "ROLLING AND SCORING MACHINE incl. EXTRUDER Conveyor belt is covered with powderin ...

Eurolux Beer Tanks / Fermentation Tanks in AISI 304 test pressure: 1,5 bar, operating pressure: 0,99 bar with Cooling Jacket with Isolation - Capacity: 1000 Litres NEW Material: V2A (AISI 304) 1.4301 Upper bottom: with Manhole with 6 Screws incl. thread connection DN 50 according to DIN 11851 with over- and underpressure valve Tank Body: with Cooling Jacket 600 mm wide with inlet 1” external thread with Isolation Lower bottom: With Conical Bottom and rest outlet underneath with a forklift and pallet truck Measurements and weight: WxH: 1150 x 1950 mm Zyl. height: 850 mm weight: 170 kg Surcharges/unit (price upon request): Fermentation Connector DN 50 Fermentation Lock Butterfly valve DN 40, DN 50 Sample Valve CIP Cleaning System Blind Cap DN 50 Immersion socket for temperature control Temperatur ...

System: piston diaphragm pump Manufacturer: Emmerich Type: SP521 2075 Machine number: 0275 Year of construction: 1977 Performance: 5m 3 with 16 bar Pressure: 16 bar Engine: BBC, 14.9 kW, 50 Hz Inlet connection: DN 50 Durckseite connection: DN 50 Dimensions: approx. 1600 mm L

description: Type: MAN 2876 LE302 gas engine for combined heat and power Power: 190kWe/1,500 rpm Standard scope of delivery â?¢ Rows â 6 cylinder four-stroke â gas engine based on MAN â D28 â?¢ Single cylinder heads, high-alloyed valve seat rings and valves, form-forged crankshaft with counterweights, wet cylinder sockets, piston cooling over oil spray nozzles â?¢ Compression ratio 11:1, biogas 1500 rpm â?¢ Main power oil filter, 2-fold, standing, not switchable with oil cooler â?¢ Closed crankcase ventilation with multi-cyclone oil separator, engine ventilation must be integrated on the customer side â?¢ Flywheel case SAE 1 â?¢ Flywheel I = 2,412 kgm2 for clutch SAE 11.5 and SAE 14 with tooth wreath â?¢ Anlassser â?¢ Valve solvets made of hard metal & ...

Outdated MAN E2876LE302 bio gas engine in Exchange.

E - engine of Exhaustor 3 x 380 volts.

MAN D 2066 LF 12 - Euro 4-287 KW - 390 HP Motor was cpl. repaired according to RAL GZ-797: with new piston rings, new bearings, new oil pump, AT cam shaft, AT injectors, new water pump, oil and fuel filters 1 year warranty without KM-limit Old Engine must be returned

MAN D 2066 LF 31 - Euro 4-324 KW - 440 HP Motor was cpl. repaired according to RAL GZ-797: with new cylinder liners, Pistons, bearings, turbochargers, air compressor, injectors, high pressure pump - without starter, alternator and clutch Repair enabled old part must be returned. Maximum mortgage of old part of 4.000,00 = €

Motor was sealed front and rear new - upgraded oil pump, thermostat, oil filter, fuel - engine was installed on engine test bench and a cpl. Test run was carried out 6 months warranty on the motor mechanism Mileage only 200,000 km old part pledge 4,500.00 = €

MAN D 2876 LF 13 - Euro 4-390 KW - 530 HP Motor was cpl. repaired according to RAL GZ-797: with new pistons and liners, new bearings, new oil pump, AT cam shaft, AT injectors, new water pump, oil and fuel filters 1 year warranty without KM-limit Bauglieches old part must be returned

MAN 2876 LE302 gas engine (biogas) 190KW (also as 210KW-Version) It's a replacement engine for various biogas CHP. Overhauled according to manufacturer guidelines and RAL quality seal(maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a quotation. We have other Exchange engines (2848 with 250KW and 2842 370KW) and AT cylinder heads, intercoolers, turbochargers, etc. and other components and spare parts for MAN gas engines in stock.

MAN 2848 LE322 gas engine (biogas) 250KW It's a replacement engine for various biogas CHP. According to one manufacturer guidelines and according to RAL quality seal repaired (maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a written offer. We have other replacement engines (2876 with 190KW and 2842 370KW) and AT cylinder heads, intercoolers, turbochargers and other components and spare parts for MAN gas engines in stock.

MAN 2842 LE322 gas engine (biogas) 370KW It's a replacement engine for various biogas CHP. According to one manufacturer guidelines and according to RAL quality seal repaired (maintenance level R3). 1 year warranty - education, and installation and service engine and optional for CHP. Please contact us for a written offer. We have other replacement engines (2876 with 190KW and 2848 250KW) and AT cylinder heads, intercoolers, turbochargers and other components and spare parts for MAN gas engines in stock.

Attachment: eccentric screw pump Manufacturer: Allweiler Type: On BP 6.2 E21 P01 Machine number: 7612455 Year of construction: 1998 Performance: 1.67 8.3 l / h Speed: 120-600 1 / min Engine: Nord, type SK Voltage: 400 V Length: approx. 900 mm Condition: used, ready

Edge glue machine HolzHer express 1437 Glue, caps, flush milling, RADIUS milling / Beveling, scraping, cutting tool for rolling edges Total revision 10 years ago everything top Year of construction 1989 L x W x H: 500 x 120 x 170 cm Weight approx. 1800 kg The machine is in top shape, ready for use. Subject to changes, errors, and intermediate sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

SOLD! ABC ENGINE 8XDXC 886KW @ 750 RPM diesel engine ABS BJ 2002

FOR SALE... COMPLETE 2 ENGINES MIRRLESS BLACK STONE ESL 6MK2 AT TURKEY TO WHOM IT MAY CONCERN; WE'VE 2 PCS COMPLETE MIRRLESS BLACK STONE ESL MK2 PROPULSION ENGINES AT OUR STOCK PLS FIND ENGINE DTLS AT BELOW TYPE ESL MK2 REV 1000RPM ENGINE SHAFT OUTPUT 1215BHP ENGINE NO. 93740 / 93738 ENGINES HAS STD CRANK SHAFT Capt. Ayhan Ugurluba BEST REGARD; Aliaga marine services E mail: info/aliagamarine.com PHN/fax: +90 232 618 03 85 Mobile: + 905556084850 aliagamarine.com TURKEY

Control cabinet EMS 2000 by Jenbacher J312 from 1997. If you are interested, we also have many spare parts for Jenbacher 312

System: piston diaphragm pump Manufacturer: Abel Type: CM G E272 Manufacturer no.: 10074 Construction year: 2013 Performance: 15 m3/h Pressure: 1.00 MPa Motor: 7,5 kW, 50 Hz

Manual Edger Esterer EWD DKV with task table good condition ! Immediately available !; Well

Esterer DKV 1 movable shaft ! feed hydraulically hydraulic and electrically roller lift: hydraulic power: 55 kW Year construction year: approx. 1982 passage: 750mm = width, 160mm = height 2 x directional laser incl. approx. 15 Circularsaws including with Splitter unit screw roll; good

- Cores are ejected separately from the mash nominal power up to 1000 kg/h engine power 5.5 (7.5) kW (PS) Electrical connection 400V 50Hz (3 phases) Electrical fuse 16 A Laenge 2 014 mm width 770 mm Hoehe 1 615 mm He He Assumption 1 615 mm Weight 220 kg Material 1.4301 / AISI 304 Connection for mash pump DN 65 AG Hoehe mash release 430 mm Hoehe stone ejection 490 mm ; New machine - best condition

capacity 500 kg/h power 3 kW electric outlet 400V 50Hz (3 phases) fuse 16 A dimensions: length 1 200 mm width 640 mm height 1 250 mm insertion resp. discharge height 1 250 mm weight 115 kg material 1.4301 / AISI 304 mash pump connection DN 65 AG stone discharge height 380 mm mash discharge height 340 mm suitable for stone fruit, berries scope of delivery 5 mm screen ; new machine - top condition

dimensions: length 643 mm width 410 mm weight 14,5 kg material 1.4301 / AISI 304 suitable for fruit and vegetable juices scope of delivery: two pipe-screens, flap valves and tees piped, with cans 0,25 mm, 2x connection parts with slotted nut DN25 ; new machine - top condition

Hercules Elite with online development G+J ML 860; good condition; cleaned and checked; with HQ RIP.; Ready. At this point we allow ourselves to note that all offered machines are in our unrestricted possession or access and are present in our warehouse. Visits and demonstrations are possible on request in our premises. We would also be pleased to inform you about our complete stock, as only part of our portfolio is presented here.

High-temperature oven with a maximum working temperature of 1,800C and lowerable/swivel bottom. All sides of the furnace chamber are heated with Kanthal super elements (= MoSi2). Temperature homogeneity is achieved by downward removable U-elements. Operation with 3 transformers and thyristor control. Chamber dimensions: 500 mm x 500 mm x 500 mm (= 125 l.). The oven is practically unused (only about 50 fires).

Mitsubishi S16R- MPTA Marine engine rebuild in 2013

J. Engelsmann mobile lifter for containers etc., max. weight 300kg, fork length approx 700mm, fork diameter 50mm, fork gap approx. 600mm, max. lift approx. 1700mm from the floor.

Edge glue machine HolzHer express 1437 Edge gluing, flush milling, caps flush milling with chamfer milling or RADIUS milling with sep. Aggregate Schwabelscheiben 2 mm and two units for chamfering or just milling milling ABS edge 2 additional units for RADIUS Hours of operation 1072.5 hours Masch. No. 721/9-203 L x W x H: 400 x 120 x 170 cm Weight approx. 900 kg Built in 1992 The machine is in good condition, ready to use. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

Pressure: 65 tons -Stroke: 140 mm -Table size: 720 x 600 mm -Plunger surface: 500 x 300 mm -Tappet adjustment: 80 mm -Strokes: 20-40 per min. -. Weight: 6000 kg -Dimensions (L x W x H): height 3.1 m -Clamping hole ø 60 x 80 mm More info on request

Hard PVC pipe extrusion plant for tubes D28/D30/D33, consisting of: Battenfeldextruder B45-24 d, ESDE tube crosshead K 010, vacuum calibration with water bath, Graewe-band trigger BA63, Graewe Abstech-and at chamfer machine STS50, various sleeves, cores, calibrations and jaws, as well as additional tube crosshead Battenfeld RS 8-40

Siemens Spare Parts