straightening press used for sale

used baler Manufacturer: PAAL Type: LIKON 110/150 Year of construction: May 2004 Specifications: Press weight up to: approx. 36 tons Press force at 275 bar: 150 t Operating pressure max. 320 bar Filling opening: approx. 2,000 x 1,020 mm Channel cross-section: 1,100 x 1,100 mm Drive power: 2 x 75 kW Flow rate: 425 m³/h Binding: 5-fold horizontal Total connected load: 176 kW Rated current: 340 A Pre-fuse (min.) 400 A Operating voltage: 3 x 400 VAC/50 Hz/N/PE Control voltage: 230 VAC / 24 VDC including: - Oil cooling - Low-pressure circuit - Free kicks - Key locking system Transport dimensions: Length: 13,803 mm Width: 2,500 mm Height: 3,164 mm without wire unwinding devices, without binding wire, without feed belt, without a personal protection system, without conveyor belt hopper and withou ...

Qty. 1 Second-hand JCO pipe press bending line Mfc.: Samyul, ROBO, Shinsung, ChangSong, Rotech, FANUC, Hyupshun, Ingersoll Built: 2003, 2008, 2009, 2013, 2014 Plate material: Mild steel Plate dim.: 16.0 x 5.2 x 0.08 m – L x W x T Pipe dia.: Φ400~Φ1650 mm Pipe Length: 6.0m ~ 16.0 m Scope of supply: JCO Hydraulic Press Tack Welder Machine Sealing Welder Pipe Heating & Rotating Device Inside Welder Outside Welder Calibration Presses Milling Cutter Cutting Machine Bevelling Machine Compressor

Good day We hereby offer you a used baler from the manufacturer Strautmann, type BaleTainer. The following technical data have been taken from the manufacturer's operating instructions and brochures, for which we cannot assume any liability for accuracy and completeness. Manufacturer Strautmann Type BaleTainer Year of construction 2013 Operating hours 18,819 hours Number of bales pressed: 7,019 pieces Press force main press 60 t Drive power 9.2 kW Machine weight press 7.38 t The press has been partially overhauled. Piston rods and gasket sets of the two main hydraulic cylinders were renewed and general maintenance work such as oil and filter changes etc. was carried out. Finally, after the overhaul work, the machine was tested. For feeding, the press has a hydraulic tilting device to empty lattice box containers at a truck ramp. For example, the machine can be par ...

Good day We hereby offer you a used baler from the manufacturer Presona AB, type LP 80 VH1. The following technical data have been taken from the manufacturer's operating instructions and brochures, for which we cannot assume any liability for accuracy and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Press force main press 78 t Specific pressing force 95 N/cm² Press force pre-press flap 28 t Dimensions of the insertion tray 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW 5-fold vertical bonding Hydraulic oil tank volume 1,000 L Press dimensions built with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Hint: The machine was u ...

Qty. 1 Second-hand press for production of Aluminium pots and discs Mfc.: SITI Built: 2005 Renewed in by experts Duration: 3-4 months Force: 4000 Ton Production of Aluminium discs & induction & normal pots Pots height: 120 / 140 mm The press will be overhauled and revamped and sold as specified below: New Piston Grinding of cylinder New Flange Table modification New pumps New gaskets etc . New electric and electronical parts New program

Machine name: Chamber filter press used Manufacturer: Netzsch Type: 1000 /110 Year of Make: 1996 Design: Side-spar press Filter pressure: 15 bar Press capacity: approx. 2509 liters Procedure: Closed Filter area: Approx. 163 m2 Plate format: 1000 x 1000 mm Number of plates: 100 Panel Material: Polypropylene Plate Conveyor: Automatic Filter Cloth Washer: Yes Cake thickness: 30 mm Closing pressure: 385 bar Dimensions: L 9,347 x W 2,245 x H 2,435 mm Curb weight: 11,800 kg Tech. Documentation: Yes Note: It will be available from January 2025 Accessories: A control cabinet, a control cabinet, a hydraulic system, a light barrier, a filter cloth washer, a high-pressure pump and drip plates Condition: Used Price: On request

Manesty Drycota 900 23 Station Double Headed Tablet Press with Type D Tooling • This Double Headed Tablet Press is Mounted on a Common Chassis Plate and Driven via Line Shaft by a Common Drive • Twin Single Compression • Turrets Are Each Fitted With 23 Type D Stations • Upper Keyed Tooling • Removed Side Attached Operation Control Panel N°. of Stations: 23 Voltage: 400 VOLTS Frequency: 50 HERTZ Phase: 3

The BTS-MF150 is the ideal waste baler for compacting your loose cardboard and plastic film waste into a bale of up to 150 kg. The baling press impresses with its ease of use, safe operation and its large filling volume, it is ideal for medium material volume. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 8 Ton Bale weight: up to 150 kg (material depending) Bale size: 1000 H (var.) x 975 W x 800 D mm Machine size: 2630 H x 1560 W x 1030 D mm Machine weight: 780 kg Transport height: 1955 mm Loading aperture: 975 W x 470 H mm Cycle times: 40 seconds Motor: 2.2 kW 16 Amp Power supply: 220 - 240 V (1 phase) Noise level: 68 dB User-friendly lever control Bale kicker for easy eject the bal ...

Rotary tablet press SPT- TP500D with double-sided press; Brvyulnw 2 layered production; Touch screen, PLC Control Panel; HMI (Human Macshine Interface); SPT-TP 500D Number of stations (Max.) D=41 B=49 BB=59 1 Max tablet ejection (two-sided) T/h 270 000 360 000 420 000 Max tablet ejection 2 layer T/h 90 000 115 000 140 000 2 Max.Tab.Diameter Round mm 13 16 25 Form 14 19 25 3 Max tablet thickness mm 8.5 4 Max main pressing force t 10 6 Dimensions mm 1150 x 1550 x 1950

The BTS-MF250 is the ideal waste baler for compacting your loose cardboard and plastic film waste into a bale of up to 250 kg. With a crush insert baler is even suitable for crushing individual small and large drums and also other sheet metal containers. The baling press impresses with its ease of use, safe operation and its large filling volume. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 15 Ton Bale weight: up to 250 kg (material depending) Bale size: 1000 H (var.) x 1200 W x 800 D mm Machine size: 2900 H x 1759 W x 1185 D mm Machine weight: 985 kg Transport height: 2250 mm Loading aperture: 1200 W x 680 H mm Cycle times: 34 seconds Motor: 2.2 kW 16 Amp Power supply: 220 - 240 V (1 phas ...

Gluing stars Polzer Floor gluing press Type: EVA - 6 E Year of manufacture 1989 6 gluing shelves with 2 special heating plates each Gluing dimension 2100 mm x 1100 mm With Leimangabestation With 2 lifting devices for loading and removing the panels With roller conveyor Workpiece thickness maximum approx. 50 mm For removal, the plate is pneumatically lifted Per floor: 7 pneumatic pressure cylinders 100 mm diameter, 100 mm stroke, compressive force 740 kg per cylinder, Movable pressure plate 250 mm x 40 mm 2 cylinders to operate the upper heating plate Insertion opening 700 mm 2 electric heating plates Each electric heating plate 220/380V, 3 kW, thermostats 0 – 120°C Operating pressure 8 – 10 bar Gluing temperature adjustable, ideally 50-65° Capacity approx. 50 m²/h With protective grille External dimensions approx. 4000 mm x 4000 mm x 3600 mm

Rotation tablet press SPT-TP 400 with high production capacity; Touch screen, PLC Control Panel; HMI (Human Macshine Interface); SPT-TP 400 Number of stations (Max.) D=30 B=36 BB=45 1 Max tablet ejection/hour T/h 125000 170 000 215 000 2 Max.Tab.Diameter Round mm 13 16 25 Mould mm 14 19 25 3 Max tablet thickness mm 8.5 4 Max main pressing force t 10 5 Max pre-press force t 2 Hqgonxsno 6 Dimensions mm 1000 x 1230 x 2000

Dough dividing and rounding machine Bread Press TOP Model Fortuna Automat Gr. 3+ with active shutdown Intervention protection with protective corners Head cleaning to the rear electrically Dividing head with stainless steel knife NEW Dough insert up to 2400g depending on TA Dough divider with 3 new knitting plates E-system NEW with return button & protective visor DGUV V3 tested Connection 400V, 1.6 kW, 16A-CEE plug Dimensions: 720 x 800 x 1510 mm WxDxH Used machine overhauled with 6 months warranty + spare parts service Option: Platform or chassis Cast Plate Service Package Maintenance contract E-Box Instruction & Commissioning Many TOP roll presses in stock!

The small rotary tablet press SPT-TPL 200 (small scale production); Touch screen, PLC control platform; HMI system; Bczkcapdbh The machines comply with the requirements of the GMP guidelines and are CE certified; Number of stations (Max.) D=13 B=16 BB=19 1 Max tablet ejection/hour T/h 46 000 57 000 68 000 2 Max.Tab.Diameter Round mm 25 16 13 Shape mm 25 19 14 3 Max tablet thickness mm 8.5 4 Max main pressing force t 5 5 Max pre-press force t 1 6 Dimensions mm 600 x 1106 x 1705

The scope of delivery includes: 01x Surface-mounted shelf rack, used Material colour: hot-dip galvanised Total depth: approx. 2,520 mm (lifting rod direction) for double rows: 2x 1,100 mm Inner depth: approx. 2,517 mm Overall width: approx. 1,120 mm (crossbar direction) Bearing rod diameter: 30|1.50 mm Frame height: approx. 30 mm Mesh size: approx. 68 x 45 mm Weight | Pcs.: approx. 30,83 Kg Internal designation: GR-114 Note: The grating may have damage, scratches, dents, welds. Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. An additional desired transport or a shipment of this item is associated with additional costs, which will be charged separately depending on the delivery location or scope of delivery.

Stainless steel pedestal for bread presses / dough-sharing machines suitable for all common bread presses massive construction resilient with 1 to easy lifting with the lift truck Stainless steel for optimal cleaning Dimensions: 735 x 640 x 170 mm, WxDxH Visit our large bakery machinery warehouse!

Storage tank / beer tank / pressure tank with cooling jacket round of V2A Operating pressure: 0.99 bar, test pressure: 1.7 bar Quantity: 100+ Content: 17-00047-1L 800 litres 17-00047-2L 1000 litres 17-00047-3L 1,200 litres 17-00047-4L 1,500 litres 17-00047-5L 1,800 litres 17-00047-6L 2,000 litres Material: V2A - AISI 304, 1.4301 Surface: inside and outside 2B=IIIC Topsoil: with pressure lid 390 mm with 1 x threaded welding nozzle DN 50 with 1 x overpressure valve with 1 x CO2 connection with 6 x star grip screws Cylider tank: with cooling jacket with 1 x beading stiffening Underbody: with forward-drawn outlet pipe DN 50 with disc valve with 4 stable feet can be underrun with pallet trucks

Storage Tank/ Pressure Tank/Beer tank 2400 liters in AISI 304 with cooling jacket Test pressure: 1,5 bar, Operating pressure: 0,99 bar - NEW Material: V2A – AISI 304 (1.4301) Operating pressere: 0,99 bar Surface inside IIIC Operating temperature in °C: 130 Upper body: Manhole lid round DN 400 with 6 screws With 1 Thread connection DN 50 and with handle bar With CO2-connection (extra charge) With overpressure valve (extra charge) Tank cylinder: With cooling jacket With connections for cooling jacket on the back inlet 1” AG, outlet 1¼”AG With connection for sample valve DN 15 ( sample valve - extra charge) With connection for temperature indicator 3/8 (temperature indicator - extra charge) Lower bottom: Rest outlet with butterfly valve DN 50 with conical bottom On 4 stable feet Easily movable with a m ...

with 130 filling valves and 26head crown corker Year of manufacturing: 1994 capacity: approx. 50.000 bph Control system to Siemens S7 - 02/2011 Reconstruction capper to crown cork and Twist off, both is possible without conversion of the capping elements

Dynajet 500 me , NEW, Operating pressure: 500 bar, Number of foerders: 15 l/min, Drive: electric 15 kW, 400 volts, Engine hours: approx: 1, Trolly, incl. zubehoer,

automatic baler Manufacturer: HSM Type: VK 8818 R-FU, 100 t Year of manufacture / delivery date: 12/2012 Operating hours: approx. 13,500 specifications: Press force: 1000 kN Specific pressing pressure: approx. 120 N/cm² Channel format: 1,100 x 750 mm (W x H) Binding: 5-fold horizontal Wire push-through: seen in the direction of pressing on the left side Filling opening: 1,800 x 990 mm Drive power: 2 x 45 kW Control: S7-300 Theoretical throughput: - At 20 kg/m³ bulk density: approx. 12.86 t/h - At 50 kg/m³ bulk density: approx. 32.15 t/h Cycle time: approx. 8.3 sec. Bale dimensions: approx. 750 x 1,100 x length (600-1,200) mm Bale weights: approx. 500 - 750 kg Machine weight: up to approx. 30,000 kg including: - Remote maintenance system - Wire Slot Maze - Press box double-walled with replaceable HARDOX 500 sh ...

Crank press ZAMECH PKRR 400A built in 1974. Technical data : - pressure: 400 tons - clearance between stands: 1020 mm - ram stroke: 315 mm - number of strokes per minute: 20 - maximum distance of the slider from the table closed: 742.5 mm - slider adjustment: 250 mm - table dimensions: 1020 x 1050 mm - main engine power: 40 kW - main engine revolutions: 1500 1 / min. - weight of the press: 40 t

Complete clean air extraction system with briquette press and piping with gate valves, etc. Extraction system for woodworking companies with briquetting press undermounted. Aspirator ALKO Type: MOBIL-JET 250 Year of construction 2003 Extraction diameter 250 mm Nominal capacity 4900 m³/h Motor power 6.5 KW Dimensions approx. 330 x 135 x 2.95 cm with suction control for automatic slide control. Briquette press WEIMA/ ALKO Type: APC30S Year of manufacture 2007 Motor power 5.5 KW Pressing capacity 30 - 50 kg/h Briquette diameter approx. 50 mm incl. complete piping with branches, bends, valves. there would be another batch of extraction pipes with fittings, which can be purchased cheaply. Plant has been dismantled and packed ready for loading. Condition see pictures, or follow the item description. Parts can also be picked up ...

Crank press HECKERT PKZ 400.1 built in 1980. Technical data : - maximum pressing force: 400 t - working path - lower position of the slider to the maximum pressing force: 21 mm - maximum drawing depth: 125 mm - pressing force using the maximum drawing depth: 160 Mp - idle speed of the slider: 18 min-1 - maximum number of switchings: 9 min-1 - ram stroke (min-max): 315 mm - slider adjustment: 200 mm - holding force of the drawing device at air pressure: 63 Mp, 5 kp / cm2 - force of the drawing device ejector at air pressure: 10 MP, 7 kp / cm2 - total weight: 38.5 t

Operating pressure: 150 bar, Number of foerders: 42 l/min, Drive: electric 15 kW, 400 volts, Engine hours: approx: 1, Trolly, incl. zubehoer,

Operating pressure: 1000 bar, Number of foerders: 17 l/min, Drive: electric 35 kW, 400 volts, 63 A, Engine hours: approx: 2 h, Trolly, incl. pistol, 10 m HD hose, 15° flat jet dues,

mechanical briquette press briquetting press chip press defective SPÄNEX Type: KS7 Total motor power 13.2 KW Pressing capacity up to approx. 300 kg/h Briquette diameter approx. 50 mm The machine has been in my warehouse for several years. In the briquette press, the brass bearing of the crankshaft is worn. The bearing bushes would have to be replaced. The control system would have to be checked. It is sold as it is, because I clean up my stock. Documents on the machine are available. Condition see pictures, or follow the item description. Parts can also be picked up by yourself. All measurements are approximate. All information to the best of our knowledge but without warranty. Subject to prior sale. The items can be picked up by yourself or shipped at the expense of the buyer. Shipping costs are a guideline, depending on the distance and unloading op ...

Operating pressure: 350 bar, Flow rate: 21 l/min, Engine: Vanguard 2-cylinder, 4-stroke gasoline engine Working hours: 2h

a hydraulic single-stand drawing press Müller model CLZ.100.1.34, Y.O.M. 1994, good condition, with UVV, Siemens S7 screen control, throat gap 400 mm, installation height 800 mm, table surface 800 x 730 mm, stroke 600 mm, drawing cushion 40 to., drawing cushion stroke 200 mm.

Used Monobelt, type: NP06-AD belt press for dewatering sludge. Belt width 60 cm. The belt is made entirely of stainless steel, has a fully automated high-pressure pump and two sets of flat jet nozzles for washing the belt. It is equipped with smooth belt feed regulation and a pneumatic installation that controls the belt tension and thus the sludge crushing force. It is also equipped with an automatic belt setting controller on rollers. The press control cabinet is very extensive and controls the press itself but also additional equipment (sludge pump, mixer, dispenser). Press with equipment: - screw pump for sludge with a capacity of 6 m3 per hour with capacity regulation, - dispenser of various types of emulsifiers with capacity regulation and a mixer. The whole is a complete set for work in the agri-food industry, processing, sewage treatment plants, distilleries, bre ...

press is after overhaul: full function complete mechanical parts, pneumatic and control system. The press has a new pneumatic clutch, the original was electromagnetic clutch as old system. Press capacity: max. 45 t Pull force: max. 45 t Counter force in pressing position: max. 17 t Stroke of the punch: 175 mm Filling height: max. 140 mm Deduction: max. 85 mm Compression distance: max. 55 mm Top pressing: max. 15 mm Stroke rate: 9 – 26 min.-1 Motor: 7,4 kW Approx: 3000x1200x1800 mm Net weight: about 5000 kg

Pressing rollers Tranklein Model 600 Year 1980 Width 600 mm Available Direct

New machine 2-year warranty Advantages: + unbeatable price-performance ratio + already standard: mobile machine, ideal for fast floor mopping + Stainless steel cutting blade + Quickly replaceable, coated cutter head + Up to 4 different cutter heads can be used with one machine + extremely wide weight range (16 gr - 400 gr round-knitted possible!) + Uniform division of the dough, excellent rounding of the dough pieces + Effective shutdown at the touch of a button + Ergonomic knife cleaning position (head can be swivelled forward by 90 degrees) + Active switch-off, pressing time and duration can be programmed + Digital display, 10 programs can be stored + Easy and quick adjustment of the effective room height + Side holder for knitted plate, immediately at hand SERIES accessories: 3 knitting plates included SPECIAL accessories, available at an additional cost: - Add ...

New machine 2-year warranty Advantages: + unbeatable price-performance ratio + already standard: mobile machine, ideal for fast floor mopping + Stainless steel cutting blade + Quickly replaceable, coated cutter head + Up to 4 different cutter heads can be used with one machine + extremely wide weight range (16 gr - 400 gr round-knitted possible!) + Uniform division of the dough, excellent rounding of the dough pieces + Effective shutdown at the touch of a button + Ergonomic knife cleaning position (head can be swivelled forward by 90 degrees) + Active switch-off, pressing time and duration can be programmed + Digital display, 10 programs can be stored + Easy and quick adjustment of the effective room height + Side holder for knitted plate, immediately at hand SERIES accessories: 3 knitting plates included SPECIAL accessories, available at an additional cost: - Add ...

waited

Filter press plate filter ultrafiltration plate filter used Manufacturer: Rhone Poulenc Type: UFP 70 Max working pressure: 4.5 bar/64 psi Torque: 8 mxkg 6x24 plates approx. 2000 x 600 H 1700 mm Changes and errors in the technical data, Information and prices as well as intermediate sale reserved.

Table top height: 910 mm Table top size: 700 x 380 mm Max drilling depth: 145 mm Max long hole length: 240 mm Height adjustment distance 135 mm Engine power: 1.5 kW Voltage: 400 V / 50 Hz Speed: 3,000 rpm Net weight: approx. 200 kg Suction nozzle: 100 mm Dm Dowel drilling device: Pitch 16, 22, 25, 32 mm with precision grid roller Driving equipment: Yes Frame stop 90°: pluggable Two-jaw chuck: up to 20 mm clamping range Hand eccentric tensioner: 1 piece 1 Lever control: Yes Measuring clock in handwheel: Yes Miter stop: Yes, double angle adjustment stop from 22.5° to 75° infinitely adjustable

Plate press Filter press Chamber filter press Industrial wastewater technology -used- Manufacturer: FAZZINI Type: F500 Operating pressure 15 bar Plate size 500 x 500 mm 20 plates with hydraulic unit 1.5 kW and piston pump 0.75 kW Dimensions: approx. 2400 x 750 x 1600 mm All items are checked for function before delivery, if technically possible !

Block glue press Müro 5000/A2 WT; Working width 705mm; 3x dryer; Stack increase; Heat guide plate; Stand unit. Padding press Müro 5000/A2 WT; working width 705mm; 3x dryer; pile elevation; heating sheet; floor mounted machine.

Code: 0119 Brand: KOLMAG - ITALY Model: PGP 600 F Hydraulic press for moulds, frames, furniture elements, solid wood doors, plastic materials, composite materials and various Press modular structure with heavy thick plates without weldings and worked by tool machine Oleodinamic plant with pistons prefilling system in order to have a quick opening and closing of the platens Dimensions of massive steel platens mm 1600 x 500 - Thickness mm 60 with electric resistances - Max temperature 260°. N° 3 pistons diameter mm 240 Pressure kg/cm2 56 Thrust Tonn 450 Safety photocells Hydraulic power unit Kw 7,5 Power absorbed heating platens 31 Kw Control board with pressure control gauge - Timer for platens opening - Telethermometer to regulate upper platen temperature - Telethermometer to regulate lower platen temperature - Switches for opening and closing of the platens - Emerge ...

The press brake HAMMERLE BM 200-3100 press brake was built in 1996. The folding machine was serviced regularly. Technical parameters of the press: - control: INFINITRON - number of NC axes: 11 - pressure: 200 tons - bending length: 3100 mm - working stroke: 400 mm - distance between the body walls: 3240 mm - maximum distance between the table and the bumper: 965 mm - voltage: 3 x 400 Volt - control voltage: 24 V = - total power: 28 kW - deflection arrow compensation - total machine width: 4400 mm - total height of the press: 3400 mm - weight of the press: 16 600 kg

For sale is a top-equipped system for briquetting including silos, conveyor technology and packaging unit, consisting of the following components: For sale is a comprehensive briquetting plant including silos, conveyor technology and packaging unit, consisting of the following components: Silo and discharge technology 2x steel silos, each approx. 20 m³ usable capacity Including silo discharge systems Briquetting presses 1x Briquetting press SPM PAWERT AG, Type 84/1 - I 90/200, Masch.-Nr. 1060, Power: 55 kW 1x Briquetting press SPM PAWERT AG, Type 96/1 - I 90/200 SBP, Masch.-Nr. 1140Bj.2021 Conveyor and transport system Complete transport route including: • - 2 cooling lines • - All conveyor belts, roller conveyors and accessories Cutting & packaging technology 2 cross-cut stations with noise protection cabin 1 Feeder KÖRA Packmat, type presumably EF-235 1 shrink pack ...

GERDA HYDOMAT PAWN 100 automatic press was built by GERDA HYDOMAT S.A. in Poland in 2001. The machine, with a high press force of 100 tonnes, is dedicated to the mass production of precision steel parts. All machining processes, i.e. precise stamping and threading of the workpieces, are performed fully automatically. The sheet metal feeder accurately feeds the material into the workspace, where the slider and reliable threading head are located. The design, which is made from the highest quality raw materials, in turn maintains the highest stability during even the most intensive challenges. The GERDA HYDOMAT hydraulic press weighs 5200 kg. Technical specifications of the GERDA HYDOMAT PAWN 100 press - press force: 100 t (1000 kN) - work table dimensions (L x W): 700 x 320 mm - height of working space: 250 mm - slider stroke: 0-70 mm - number of slider strokes: 10-40/min - numbe ...

Completely overhauled HSB 15 incl. certified oil pan and protective fence for a quick and Trouble-free commissioning. Overhauled in 2021 Optional new 8m3 bunker and conveyor screw available. Including. Used machine warranty

Qty. 1 Second-hand crank hot forging press – dismantled & in storage Mfc.: Hyunjin Industry, Korea Built: 2008 Status: dismantled and in storage Force: 2500 T Total weight of the machinery: approx. 250 T

ADIRA BB 3515 servo electric press brake was built in 2018 in Portugal by ADIRA – Metal Forming Solutions, S.A. The offered machine, apart from passing the start-up tests, has not worked in production and is like new. The ADIRA BB3515 CNC press brake is the perfect choice for precision machining of workpieces with a maximum length of 1500 mm. The machine is distinguished by the use of many state-of-the-art technical solutions, thanks to which it will meet all, even the most intensive challenges of modern business. The powerful electric drive developed in Bluedrive technology, is free of any filters, seals and hydraulic oil compared to a standard hydraulic system. This solution makes the machine much faster, quieter and more environmentally friendly than other presses available on the market. The electric drive also eliminates the occurrence of the so-called deflection arrow and its  ...

Press brake edge machine edge bench press used Manufacturer: Mengele Type: C320-4B Built: 1966 last revision and repair: 2000 Location D-01587 Riesa Dimensions WxH: 6,250 x 3,650 mm Edge knife width: 6,150 mm sheet thickness at 6,000 mm bending length: approx. 7.5 mm. The machines are designed for very deep shaft bends, therefore very deep cheek recesses. Original 300 t pressing force - In 1989 the pressing force was increased to 350 t. The press is in very good condition despite its age. The machine is disassembled and ready for loading. documentation for the machine is available. Weight: about 45 t

250 ton x 3000mm 3100mm ben length 3200mm between frames MASSIVE tooling package Bend aid and voice control!

Baler Presto CC 20 M, built in 2019, press force 20 t, with restraint. Specifications: Manufacturer: Presto Type: CC 20 M Year of Make: 2019 Hours: 1022 Press force: 20 t Cycle time: 24 s Drive power: 7.5 kW Filling opening: 1030 x 750 mm Filling volume: 0.53 m³ Binding: 3-fold, manual Throughput at bulk density of 35 kg/m³ - 1.6 t 60 kg/m³ - 2.3 t 100 kg/m³ - 2.8 t Bale dimensions: 700 x 750 mm Bale weight: up to 300 kg Dimensions: 3300 x 1235 x 1860 mm (LxWxH) Machine weight: approx. 2500 kg Materials: paper, cardboard, foil Remark: The machine is in good condition. It was inspected and tested by us in 28816 Stuhr. You can find the video at the top of the pictures, or on our website or YouTube channel. Viewings, also under power, are possible at any time by arrangement. Video calls are possible on request. We will also be happy to answer any questi ...

Stationary high-pressure pump unit Hammelmann HDP 77 on base frame. Similar/no Uraca, Woma, Kamat Pump type: HDP 77 Operating pressure: 490 bar Flow rate: 59 l/min. Drive speed: 1800 RPM Drive power: 65 kW with AC 55 kW 3 motor AH 250 M-4; 400V; 50 Hz Dimensions LxWxH: approx. 1665x1212x1641 mm Weight: approx. 1050 kg Built: 2008 Condition: in very good used condition. Includes complete documentation.