129,270 used machines on RESALE, but how to find them? Machine Search
Vertical milling machine SPECIFICATIONS: Spindle milling machine: Ø 25 mm Speed: 12000 rpm Installed power: 2.2 kW ACCESSORIES: 3-roller drive with speed controller
Offer 22646 Hydraulic profile and bar steel shears with notching device and hole punch Specifications: - Flat steel scissors - Flat steel - 400 x 16 mm - or: 300 x 18 mm - Profile steel shears - L- and T-irons at 90° 130 x 12 mm - Square steel / round steel 40 / 40 mm - Notcheter - with square clinker for sheet metal up to approx. 13 mm - Latch depth approx. 70 mm - Latch width approx. 52 mm - Hole punch - Punching force approx. 60 t - Projection 400 mm - Stroke approx. 10 to 50 mm - perforated in steel up to Ø 31 in 15 mm - Material stop - div. 10 pcs punches + matrices - Drive 400 V / 5.5 kW - Dimensions W 1100 x H 2000 x D 1700 mm - Weight approx. 2100 kg
Stephan MCV12 Microcut, continuous cutter, colloid mill, koial mill, ultra-fine shredder Voltage: 400V Speed: 2900rpm Power: 8800W Stainless steel funnel Spout with DN50 milk thread, thus the possibility of retrofitting a circulation device for product circulation neat condition smooth running should be thoroughly cleaned before use Video about test run available
Hydr . Flat profile and bar steel shears with notching device and hole punching Specifications: - Flat steel shears cut up to 375 x 10 mm - 220 x 20 mm - Profile steel shears - cuts L-steel at 90° to 130 x 13 mm - Steel bar shears - cuts round steel up to 45 mm - Square steel up to 45 mm - Notching device - with square notching device 100 x 42 x 10 mm - Hole punch - punching force 600 KN - with stop table - Projection 300 mm - perforated in steel up to 28 mm Ø in 15 mm - or 34 mm Ø in 12 mm - manual length stop - Drive 400 V / 4 kW - Space requirement approx. W 600 x H 1550 x D 1500 mm - Weight approx. 1300 kg
Vacuum cutter Alpina PBV 330-1110 DC Manufacturer Switzerland Year of production Overhauled Technical data overall dimensions 3300x2600x2450 mm; bowl 330 ltr; power supply 400 V, 50 Hz; total power 115 kW / 150 A; knives speeds 550/975/1950/2500/3200/4100 rpm, main motor 103 kW DC; bowl speeds 4/8/12/16 rpm, bowl motor 1,2 kW; mixing speeds 65/130 rpm, hydraulic system 5,5 kW; loader; unloader; vacuum pump Busch 250 m3/h, 5,5 kW; weight 5600 kg.
Size untrimmed max 410 x 315 mm Size trimmed max 380 x 300 mm Size trimmed min 80 x 50 mm Feeding height max 100 mm False opening max 130 mm Table height 900 mm Good working conditions
Max. punching capacity: 600 kN Max. shear power: 800 kN Punches 27 mm holes in 16 mm steel Shears on the flat steel shears to 400 mm up to material thickness of 16 mm steel Hydraulic hold-down device on flat steel shears Further technical data on request With an assortment of punches and dies as desired Weight: approx. 2,000 kg
used
Compressive force max.: 55 kN Projection: 175 mm Punching stroke adjustable: 0 - 28 mm Number of strokes at 15 mm stroke: 30 Adjustable notch stroke: 0 - 60 mm Hydraulic drive: 380 V, 3 kW Required space: 1170 x 620 x 1470 mm Weight: 930 kg
Motor for folding machine Eurofold / Foldmaster 235 / 435 / 200 / 400 Art.: PS2356
Various turning tools Kennametal, Widia and others Prices on request. Complete package or individually. Other items available on request. A total of 13 lattice box tools through company liquidation. All new and unused. Estimated about 10 tons of mass. Mainly Kennametal, Widia, as well as HSK mounts (approx. 300) and various milling heads (approx. 300).
Face cutting knife for Polar 66 Art.: PS153 Ersatzteil Nr. / parts No. 446282 / 280403 Qualität/ Quality : HSS Stahl Kanefusa from Japan Made in Germany Dimensions: 805x95x9.7 mm. Number of holes: 14 / M: 10 Number of rows of holes: Packaging : Disposable crate
Messer für Papierschneidemaschine / paper knife - guillotine Polar 55 Art.: PS832 Ersatzteil Nr. / parts No. 241580 Qualität/ Quality : HSS Stahl Kanefusa from Japan Made in Germany Dimension: 685x95x9.7 Number of holes M10: 14 Number of rows of holes: 2 Packaging : Disposable crate
Knife für Papierschneidemaschine / paper knife - guillotine Polar 76 Face cutting knife for Polar 76 Art.: PS342 Ersatzteil Nr. / parts No. 233231 Qualität/ Quality : HSS Stahl Kanefusa from Japan Made in Germany Dimension: 925x110x9.7 Number of holes M10: 14 / 2 lift holes Number of rows of holes: 2 Packaging : Disposable crate
Seydelmann K40 Bowl cutter 2008, Stainless bowl cutter, three blade assembly, variable speed, timer and temperature controls, 3Ph
Paper knife - guillotine Polar 78 / 80 Art.: PS223 Ersatzteil Nr. / parts No. 424409 (273893) (446280) Qualität/ Quality : HSS Stahl Kanefusa from Japan Made in Germany Dimensions: 960x110x11.7 mm. Number of holes M10: 18 Number of rows of holes: 2 Packaging : Disposable crate
IMAC Plasma Cutter Working range 3000x1500 Workable thickness 15/20 mm. complete with vacuum cleaner Updated Software CD
Messer HSS für Papierschneider / paper knife HSS - guillotine Ideal 7228 / 7260 (Krug & Priester) Art.: PS4409 Ersatzteil Nr. / parts No. 9000141 Qualität/ Quality : HSS Stahl Kanefusa from Japan Made in Germany Dimensions: 840x100x10 mm. Number of holes M10: 6 Number of rows of holes: 2 Packaging : Disposable crate
WEINIG Rondamat R 934 Machine for manual profile knife grinding / regrinding profile knife Sharpening of straight knives in the planer head – according to a template Tool flight circle min. 100 mm / max. 300 mm Tool width max. 240 mm Grinding wheel diameter min. 150 mm / max. 225 mm Grinding wheel bore 60 mm Mandrel D=40 mm Grinding wheel width – ceramic 5 mm Borazon 10 mm Grinding wheel output 1.1 kW Spindle speed, infinitely variable 500 – 3,000 rpm. Clearance Angle – Radial (Back) 10 – 30 degrees Axial (lateral) 0 – 20 degrees Axial for planer heads 60 degrees Coolant tank approx. 50 litres Electrical connection approx. 1.5 KW Operating voltage 380 V / 50 Hz Machine complete with accessories Machine technically and optically in good condition – fully functional Packing: On pallet Payment: Net cash register be ...
Cutter head for Microcutter - Fine shredder Inotec I175mm 6 winged : 1 new, 1 used Catalog number: 30026242 3 winged : 1 x used Catalog number: I175 - 3-6-6 ( 3-6-6 ) Request a Quote iNTER-WiBA Sp.J. Ul. Krakowska 263 PL 43-305 Bielsko-Biała VAT number: PL547-17-47-669 Phone: 0048/33 812 58 60 fax. 0048/33 812 58 36
WEINIG Rondamat R 934 S/N 934-733, YOC 1996 Machine for manual profile knife grinding / regrinding profile knife Sharpening of straight knives in the planer head – according to a template Tool flight circle min. 100 mm / max. 300 mm Tool width max. 240 mm Grinding wheel diameter min. 150 mm / max. 225 mm Grinding wheel bore 60 mm Mandrel D=40 mm Grinding wheel width – ceramic 5 mm Borazon 10 mm Grinding wheel output 1.1 kW Spindle speed, infinitely variable 500 – 3,000 rpm. Clearance Angle – Radial (Back) 10 – 30 degrees Axial (lateral) 0 – 20 degrees Axial for planer heads 60 degrees Coolant tank approx. 50 litres Electrical connection approx. 1.5 KW Operating voltage 380 V / 50 Hz Machine complete with accessories Machine technically and optically in good condition – fully functional Packing: On pallet Payment ...
Manufacturer: INOTEC Type: I225 Cutter head 6-winged for continuous cutter - ultra-fine shredder Inotec I225 mm Catalogue Number: I2250039048 / I09110027-I225I6-6-6 Request a Quote iNTER-WiBA Sp.J. Ul. Krakowska 263 PL 43-305 Bielsko-Biała VAT number: PL547-17-47-669 Phone: 0048/33 812 58 60 fax. 0048/33 812 58 36
Manufacturer: INOTEC Type: 175 for engines 75 D , 90 D Lug ring for Mikrocutter INOTEC 175 Article number : V500661-1 / 175-0020123 Request a Quote iNTER-WiBA Sp.J. Ul. Krakowska 263 PL 43-305 Bielsko-Biała VAT number: PL547-17-47-669 Phone: 0048/33 812 58 60 fax. 0048/33 812 58 36
Shaftless Unwind Monomatic Typ MD 107 (150 mm core diameter) FIFE side edge control max. roller diameter 1,070 mm Web tension control device Multiple breaking device Trimming station Cutting accuracy +/-0.2 mm Automatic angle adjustment Automatic sheet length adjustment without gear change Working width up to 1250 mm min. Working width 600 mm, cutting length from 550 to 1500 mm Materials from 60 g/sqm to 150 g/sqm (unwinder max. 120 g/m2) Ionisation device Waste ejection station Shingled delivery Belt delivery extended to the end of the stack Counting device Pile delivery with jogger max. mechanical output 300 m/min Cerutti embossing station - suitable for surface embossing (steel - paper 1 : 1.85) Embossing calender output max. 250 m/min
CREEL KNIFE - CUTTING CREEL FOR DICE CUTTER MACHINE TREIF - USED 1 set. GATE KNIFE D = 20 mm for cube cutter TREIF FELIX AND FOR TREIF DERBY Art.Nr. 51823 1 set CREEL KNIFE D = 26 mm for cube cutter TREIF FELIX CE Art.Nr. 51818 Request a Quote iNTER-WiBA Sp.J. Ul. Krakowska 263 PL 43-305 Bielsko-Biała VAT number: PL547-17-47-669 Phone: 0048/33 812 58 60 fax. 0048/33 812 58 36 abc.inter-wiba.com.pl infointer-wiba.com.pl
Specifications Type: KBLH 700 Dimensions (LxWxH): 1850 x 680 x 2050 mm Working height: 700 mm Cutting length: 510 mm Knife length: 520 mm Max. shear cross-section: 3500 mm Stroke of the scissors, infinitely variable: 0 – 45 Max. stroke number of scissors: 11 PMG knife for: L-steel 90°+45°/ T-steel 90° Required power : 8.5 kW Weight approx.: 2950kg
Bowl cutter Kramer+Grebe SM 80 Overhauled Technical data overall dimensions 2000x1150x1800 mm; bowl 80 ltr; power supply 400 V, 50 Hz; power: main motor 15/20 kW; bowl motor 1,1/1,4 kW; mixing motor 1,3/1,8 kW; unloader motor 0,75 kW; 2 knives speeds 1500/3000 rpm; 2 bowl speeds; 2 mixing speeds; weight 1500 kg
Offer 23294 Specifications: - Flat steel shears - knife length 470 mm - for flat material 450 x 15 mm - or 300 x 20 mm - Sectional steel shears - L- steel at 90° 140 x 13 mm - at 45° 70 x 7 mm - T-steel at 90° 70 mm - Bar steel shears - round steel 50 mm - Square steel 42 mm - Notching device - rectangular notching 52 x 90 x 12 mm - Punch punch - punching force approx. 750 KN - - Infinitely variable stroke 0 - 70 mm - Perforates in steel up to 30 mm Ø in 20 mm - Projection 310 mm - Hydraulic drive 400 V / 7.5 kW - Space requirement approx. W 1600 x H 1850 x D 1400 mm - Weight approx. 2400 kg - With: - 2 E. foot switches for two separate workstations - Slewing ring
Three knife trimmer - in-line Make Challenge Model CMT-330 Year 2005 Serial 05010048 Min untrimmed size 178 x 127 mm Min trimmed size 148 x 100 mm Max untrimmed size 330 x 330 mm Max trimmed size 307 x 328 mm Stack height 51 mm Min trim 2.5 mm Max trim 152 mm Speed up to 400 cycles per hour in single stream mode Memory up to 99 set-ups Change over time Fully automatic within 20 seconds Details 56600 Tilt in-feed conveyor + 56421 cooling down elevator + 56420 exit conveyor, this machine can be used in-line with a perfect binder Available direct
Three knife trimmer Make Challenge Model CMT-330-B Year 2010 Serial 10040217 Min untrimmed size 178 x 127 mm Min trimmed size 148 x 100 mm Max untrimmed size 330 x 330 mm ( Max trimmed size 307 x 328 mm Stack height 51 mm Min trim 2.5 mm Max trim 152 mm Speed up to 400 cycles per hour in single stream mode and 700 in Multi stream mode Memory up to 99 set-ups Change over time Fully automatic within 6 seconds Details 56416 manual in-feed conveyor + 58000 vertical stacker Available direct
Stephan MCH10/2 Microcut, continuous cutter, colloid mill, coial mill, ultrafine shredder Machine in neat condition Voltage: 400V Power: 4000/4500W Speed: 1415/2920rpm neat and smooth running Machine must be thoroughly cleaned before use Cutting gap: 1.3mm The machine was operated "inline" by the previous owner, so there is no circulation device, but this can be easily built with DN50 milk thread screws. Video about test run available
Max. punching capacity: 600 kN Max. shear capacity: 1000 kN Punches 20 mm holes in 19 mm steel Shears on flat steel shears to 500 mm up to material thickness of 12 mm steel Further technical data on request With an assortment of stamps and dies as desired
Panel thickness (min/max) 5/50 mm Cutterhead rotation speed 30000 rpm Motor power 0,8 kW Table dimensions 320x440mm Milling axis Ø 6 mm Sufficient and constant compressed air Ø 6 mm Power 220 V/50Hz Transport dimensions 720x500x470 mm Weight 25 kg Price 299 Eur (EXW Jonava, Lithuania
Equipped with 3 standard tools : A : 207x174 mm B : 134 x 101 mm K :
Max. punching force: 700 kN Projection: 510 mm Cuts on flat steel shears 500 x 18 mm Punches e.g. 30 mm diameter in 20 mm flat bars Quick-change device Assortment of tools is included in the price Weight: 3,000 kg
Many of our machines are available from stock. Call and ask to find out more. CNC plasma cutting machine PCO-2010-D The machine was engineered and manufactured in Poland. Working parameters: - XY operating range (working area): 1020 x 2100mm - Clearance between table and gantry: 240 mm - Maximum cutting tube height: 200 mm - Idle speed (Cutting speed depends on the capacity of the plasma source and the thickness of working material.): 25000 mm/min. - Compatible with Hypertherm Powermax 45-125, and Hypertherm MAXPRO200 plasma sources. Structure specifications: - Length: 2650 mm - Width: 1780 mm - Height: 1500 mm - Total mass: 800.0 kg - Maximum load: 800.0 kg - Adjustable support legs: 4 pcs Easy application of metal sheets The entire gantry and the head are designed to travel out of the working area. This makes applying large sheets of metal easy. Systems THC ...
A NEW USED Compact - FLAT - FINGER-JOINTING line Manufacturer: GÖTZINGER Year of construction 2019 Max. 140 mm x 80 mm Min. 20 mm x 30 mm Built up and immediately available Milling, gluing, pressing, capping Sale as inspected without warranty and guarantee Self-dismantling with full assistance For the production of all mouldings inside and outside, floors and much more. All built in a line, about 35 m long. Gluing one-component PU glue waterproof Technical description on request
Many of our machines are available from stock. Call and ask to find out more. CNC plasma cutting machine PCO-2010-D The machine was engineered and manufactured in Poland. Working parameters: - XY operating range (working area): 1020 x 2100mm - Clearance between table and gantry: 240 mm - Maximum cutting tube height: 200 mm - Idle speed (Cutting speed depends on the capacity of the plasma source and the thickness of working material.): 25000 mm/min. - Compatible with Hypertherm Powermax 45-125, and Hypertherm MAXPRO200 plasma sources. Structure specifications: - Length: 2650 mm - Width: 1780 mm - Height: 1500 mm - Total mass: 800.0 kg - Maximum load: 800.0 kg - Adjustable support legs: 4 pcs Easy application of metal sheets The entire gantry and the head are designed to travel out of the working area. This makes applying large sheets of metal easy. Systems THC ...
Punching force: 750 kN (punches e.g. 30 mm in 22 mm material), with search device via foot switch for punching Projection: 320 mm Cuts 450 x 15 mm or 300 x 20 mm on flat steel shears Support table on the punching side Two separate foot switches for the punching and shearing side, so that independent punching and shearing can be carried out Assortment of tools is included in the price
Many of our machines are available from stock. Call and ask to find out more. CNC plasma cutting machine PCO-3015-D The machine was engineered and manufactured in Poland. Working parameters: - XY operating range (working area): 1520 x 3100mm - Clearance between table and gantry: 240 mm - Maximum cutting tube height: 200 mm - Idle speed (Cutting speed depends on the capacity of the plasma source and the thickness of working material.): 25000 mm/min. - Compatible with Hypertherm Powermax 45-125, and Hypertherm MAXPRO200 plasma sources. Structure specifications: - Length: 3650 mm - Width: 2280 mm - Height: 1500 mm - Total mass: 1100.0 kg - Maximum load: 1800.0 kg - Adjustable support legs: 6 pcs Easy application of metal sheets The entire gantry and the head are designed to travel out of the working area. This makes applying large sheets of metal easy. Systems T ...
Many of our machines are available from stock. Call and ask to find out more. CNC plasma cutting machine PCO-3020-D The machine was engineered and manufactured in Poland. Working parameters: - XY operating range (working area): 2020 x 3100mm - Clearance between table and gantry: 240 mm - Maximum cutting tube height: 200 mm - Idle speed (Cutting speed depends on the capacity of the plasma source and the thickness of working material.): 25000 mm/min. - Compatible with Hypertherm Powermax 45-125, and Hypertherm MAXPRO200 plasma sources. Structure specifications: - Length: 3650 mm - Width: 2780 mm - Height: 1500 mm - Total mass: 1450.0 kg - Maximum load: 2000.0 kg - Adjustable support legs: 6 pcs Easy application of metal sheets The entire gantry and the head are designed to travel out of the working area. This makes applying large sheets of metal easy. Systems T ...
Many of our machines are available from stock. Call and ask to find out more. CNC plasma cutting machine PCO-4020-D The machine was engineered and manufactured in Poland. Working parameters: - XY operating range (working area): 2020 x 4100mm - Clearance between table and gantry: 240 mm - Maximum cutting tube height: 200 mm - Idle speed (Cutting speed depends on the capacity of the plasma source and the thickness of working material.): 25000 mm/min. - Compatible with Hypertherm Powermax 45-125, and Hypertherm MAXPRO200 plasma sources. Structure specifications: - Length: 4650 mm - Width: 2780 mm - Height: 1500 mm - Total mass: 1850.0 kg - Maximum load: 2500.0 kg - Adjustable support legs: 8 pcs Easy application of metal sheets The entire gantry and the head are designed to travel out of the working area. This makes applying large sheets of metal easy. Systems T ...
Many of our machines are available from stock. Call and ask to find out more. CNC plasma cutting machine PCV-6020-D The machine was engineered and manufactured in Poland. Working parameters: - XY operating range (working area): 2020 x 6100mm - Clearance between table and gantry: 240 mm - Maximum cutting tube height: 200 mm - Idle speed (Cutting speed depends on the capacity of the plasma source and the thickness of working material.): 25000 mm/min. - Compatible with Hypertherm Powermax 45-125, and Hypertherm MAXPRO200 plasma sources. Structure specifications: - Length: 6750 mm - Width: 2780 mm - Height: 1500 mm - Total mass: 2600.0 kg - Maximum load: 5000.0 kg - Adjustable support legs: 10 pcs Easy application of metal sheets The entire gantry and the head are designed to travel out of the working area. This makes applying large sheets of metal easy. Systems ...
Max. punching capacity: 600 kN Max. shear capacity: 800 kN Punches 27 mm holes in 16 mm steel Shears on the flat steel shear to 400 mm up to material thickness of 16 mm steel Hydraulic hold-down device on flat steel shear Large support table on the punching side with stops Further technical data on request With an assortment of stamps and dies as desired Weight: approx. 2,000 kg
Cutting table for 36 NF stones. There is equipment for formats 1.4 and 2.1. The cutter only in use for 5 months
with laser positioning aid at the punching station Hydraulic cylinders with fast return stroke Easy installation of special tools Projection also available in 310 mm including punch/punch search device Punching capacity: D 22 x 18, D 50 x 8 mm Max. stroke length: 100 mm Table size: 700 x 700 mm Projection: 510 mm Dimensions: 1520 x 820 x 1960 mm Weight: 1850 kg
with 5 stations Punching diameter: 40 x 8/22x 15 mm Projection: 165 mm 1-cylinder machine with footswitch with lighting Stop: 1000 mm Projection: 165 mm Punching diameter: 40 x 8/22 x 15 mm Blade length: 300 mm Notching: 50 x 90 x 70 mm Total power requirement: 3.7 kW Colour: blue/beige Angle steel: 75 x 75 x 6 mm Flat steel: 300 x 10 mm Square steel: 25 x 25 mm Round steel: D 30 mm Punching pressure: 45 t Dimensions: 1050 x 760 x 1490 mm Weight :840 kg
Punching capacity: ø 18x14 mm, (diameter and thickness): ø 50x5 mm U-steel height: 180 mm Max. stroke length: 100 mm Stroke rate/min. (20 mm stroke): 41 Max. hole diameter: ø 160x2 Motor power: 3.7 kW Punching force: 35 ton Weight: 1200 kg
Automatic controlled guillotine cross knife Consistent high throughput Chamber length: 620 mm Chamber cross section: 120 x 120 mm
maximum number of results exceeded
please refine your search
