128,847 used machines on RESALE, but how to find them? Machine Search
Bezel, steady rest, lynette -max passage. Ø: 320mm (410mm) -Center height: 500 mm -Drawing: with the photos -Dimensions: 1000/270/H900 mm -Weight: 216 kg
Dreh-Øüber Bett: 400 mm Dreh-Øüber Support: 220 mm turning length: 1000 mm spindle turning speed range: 12,5 - 2000 U/min spindle taper: Bajonett 55022 spindle bore: 47 mm feeds - longitudinal: 0,07 - 4,16 mm/U feeds - cross: 0.035 - 2,08 mm/U thread - mm pitch: 0,87 - 192 mm thread - inch: 2 - 24 Gang/ inch. rapid travel - longitudinal/face: 3,4 / 1,7 m/min spindle drive: 11 kW power capacity: 13 kW weight of the machine ca.: 2,8 t dimensions of the machine ca.: 2,8 x 1,2 x 1,5 m • 3-jaw chuck Ø 250 mm, 4-jaw chuck 200 mm, • 2-axis- digital display, ANILAM WIZARD LATHE - refinished in 1992, The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Clamping table, clamping angle, T-slot table, rotary table, milling machine table -Table surface: 500 x 200 mm -4x T slots: 14 mm -Clamping angle: rotatable, swiveling, tiltable -Foot recording: mm -Dimensions: 500/300/H210 mm -Weight: 50.5 kg
Electric motor, three-phase motor -Power: 0.55 kW -Speed: 1370 rpm -Shaft: Ø 19 mm -Construction: B3 -Protection class: IP 44 -Dimensions: 290/150/H190 mm -Weight: 10.3 kg
faceplate diameter: 1130 mm swing diameter: 1500 mm turning height: 1100 mm faceplate diameter: mm swing diameter: mm total power requirement: 30 kW weight of the machine ca.: t dimensions of the machine ca.: m Brand: STANKO TYPEL 1512 Build in: 1977 with pneumatick 3-jaw stuck 1130 mm max. turning diameter 1500 mm max. turning height 1100 mm Motor 30 KW The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Hydraulic unit, hydraulic pump, hydraulic pump -Max. pressure: 63 bar -Liter flow rate: 6 l/min -Hydraulic tank: 40 liters -Dimensions: 690/400/H700 mm -Weight: 100 kg
hydraulic unit, hydraulic pump, hydraulic pump, universal unit, hydraulic station, -Manufacturer: Stankoimport Caenaho, hydraulic unit -Motor: 220/380 V/ 1400 rpm -Individual components: Technical data see photos type plates -Dimensions: 420/380/H310mm -Weight: 30 kg
Machine vice, sturdy vice, drill press vice -Machine vice: with MK5 / M20 holder -Type: 36642.M11 -Clamping jaws 80 x 22 mm -Clamping depth: 40 mm -Dimensions: 215/175/H80 mm -Weight: 3.7 kg
Nominal weight of the falling parts: 750 kg Max. number of blows per minute: 105 Kinetic energy: 1900 kg Distance from an axis of the slider up to bed: 750 mm Cylinder diameter: 600 mm Diameter of the plunger: 630 mm Max. headstock travel: 835 mm Dimensions: -Left-to-right: 3940 mm -Front-to-back: 1430 mm Height above floor level: 3260 mm Weight: -With an anvil-block: 25600 kg -Without an anvil-block: 16600 kg
Bezel, steady rest, lynette -Bezel: max. aperture Ø 75 mm -Type: 36642.M44 -Centre height: approx. 125 mm see photos -Dimensions total: 135/310/260 mm -Weight: 7.3 kg
Tailstock, counter bearing for dividing head, dividing head, tailstock for tool grinding machine, cylindrical grinding machine -Tailstock: center height 125 mm -Type: 36642.M3 -Recording: MK2 -Dimensions: see photos -Dimensions: 270/230/H180 mm -Weight: 8.5 kg
Tailstock, counter bearing for dividing head, dividing head, tailstock for tool grinding machine, cylindrical grinding machine -Tailstock: center height 125 mm -Type: 36642.M2 -Recording: MK2 -Dimensions: see photos -Dimensions: 255/200/H170 mm -Weight: 7.1 kg
Tailstock, counter bearing for dividing head, dividing head, tailstock for tool grinding machine, cylindrical grinding machine -Tailstock: Center height 83-175 mm adjustable/swivelling -Type: 36642.M31 -Dimensions: see photos -Dimensions: 280/220/H270 mm -Weight: 12.1 kg
spherical roller bearing -Bearing type: Spherical roller bearing -Bore: Ø 80 mm -Outer diameter: 140 mm -Width: 33 mm -Weight: 2.2 kg
spherical roller bearing -Bearing type: Spherical roller bearing -Bore: Ø 110 mm -Outer diameter: 200 mm -Width: 53 mm -Weight: 7.5 kg
Hydraulic unit, hydraulic pump, hydraulic pump -Max. pressure: 80 bar -Liter flow rate: 18 l/min -Motor: 2.2 kW 950 rpm -Hydraulic tank: 800/650/H280 mm -Dimensions: 1000/650/H1150 mm -Weight: 400 kg
Spline shaft milling machine STANKO 5350 without change gears.
Key data: 50 mm, 2000 1/min
Solid bench boring mill of the brand Stanko-Import, model 2H125 Stanko import Type: 2H125 Year of construction approx. 1975 massive rod drill with MK4 mount in good condition. Dimensions: L860 x W850 x H2400 Weight approx.: 1050 kg Motor 2,2Kw 380V Drilling depth gauge Automatic threading (RE-LI)up to M24 Drehz. 45 -2000 in 12 stages Feed 0.1-1.6 / Umdr.in 9 levels Projection 200mm Adjustment ranges: quill stroke 280mm Drill head 170mm Table 270mm, 400x400 The machine can be viewed at any time. On-site loading can be easily carried out with a forklift. Transport possible throughout Germany via freight forwarder.
Rotary table, rotary indexing table, dividing head, dividing head -Clamping surface: Ø 250 mm -Groove: 20 mm -Height: 108 mm -Dimensions: 580/350/H120 mm -Weight: 36 kg
model is 5B 150P - table diameter is 800mm - max stroke is 160mm - control is Omron NS12 - logic equipment and sensors: Omron CS1 series CPU control cards Electric drawings and safety and instructions for use are updated at 2004 same as the modernisation
Various fixed steady rests for lathes up to center height approx. 600 mm
x-travel:630 mm y-travel:200 mm z-travel:360 mm total power requirement:7,5 kW weight of the machine ca.:2,5 t dimensions of the machine ca.:1500 x 1800 x 1900 mm spindle taper:SK40 table-size:250 x 1100 mm
rotary table dia.:400 mm weight of the machine ca.:130 kg dimensions of the machine ca.:500 x 600 x 160 mm
STANKO 2N636GF1 Horizontal boring mill MITSUBISHI controler, new 2013 Spindle 125 mm Table 1600 x 1800 mm Max. horizontal (axial) movement of the spindle (Z') - 1000 mm Max. vertical movement of the headstock (Y)- 1400 mm Max. longitudinal movement of table (Z, W) - 1600 mm Max. lateral movement of table (X) - 1400 mm The largest mass of the processed product - 8 tons Spindle speed - 8 ... 1250 rpm Spindle Drive Electric Motor - 20 kW The weight of the machine is full - 34.6 tons
Max. diameter of initial blank: 30 mm Blank length: -Min.: 120 mm -Max.: 300 mm Max. diameter of upset flange: 60 mm Upset slide nominal force: 2500 kN Max. force on clamping slide with dies closed: 2500 kN Stroke: -Movable die: 100 mm -Upset slide (full): 220 mm -Die closing: 140 mm Slide strokes per minute: 45 Machine overall dimensions: -Length: 6050 mm -Width: 4600 mm -Height: 2260 mm Machine weight: 24680 kg
for production of forgings by forging of ferrous, non-ferrous metals and alloys in the hammer dies model M212 Impact energy, 50 kJ Nominal weight of falling parts, kg 2000 Stroke woman, mm 1200 Stroke woman, mm 1200 Machine dimensions Length Width Height (mm) 3650X1660X5310 Weight kg 58.310, spare parts available
faceplate diameter: 2200 mm swing diameter: 2500 mm turning height: 1600 mm Control: Siemens chip conveyor: total power requirement: 100 kW weight of the machine ca.: 35 t dimensions of the machine ca.: m vertical lathe with two RAM, faceplate Ø 2000 mm, SPS supported control for storable cycles, RAM/channel 1 two Capto recordings C8 with Internal tool cooling, RAM/channel 2, two Capto mounts C8 with internal tool cooling, Chip conveyor / spindle Z-axis as new / without KSS Filter unit / 3 glass scales are missing / control panel is disconnected but complete and OK, a 90 degree angle is missing from the control panel arm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Machine vise STANKO / BZSP (Made in USSR) jaw width: 300 mm span: 20 - 275 mm on rotary table with graduation solid design ! Dimensions: 550 x 370 x 225 mm
Rotary table STANKO 720440023 Ø 400 mm Table height: 160 mm used, tested ! Dimensions: 500 x 600 x 160 mm
Machine vise STANKO / BZSP (Made in USSR) Model: 7200-0221 jaw width: 200 mm jaw height: 65 mm Span: 0...260 mm on rotary table with graduation 360° rotatable solid design !' Dimensions: 600 x 370 x 185 mm
Machine vise STANKO jaw width: 250 mm span: 220 mm jaw height: 70 mm good condition ! Dimensions: 650 x 300 x 180 mm
Face Plate STANKO 7103-0049 Outer Ø: 400 mm Bolt Circle Ø : 135 mm Bore Ø: 100 mm New ! preserved ! Dimensions: 400 x 400 x 165 mm
Clamping jaws, jaw boxes for face plate type 1516
Spline shaft Grinding machine STANKO 3M451B/1500 with accessories.
sheet width: 2050 mm plate thickness: 8 mm distance between columns: mm electrical: . weight of the machine ca.: 6,3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
roll diameter: 440 mm throat: 420 mm workpiece height: 200 mm cutting speed: 20 - 1550 m/min table surface area: 560 x 560 mm band length: 3250 mm total power requirement: 1,5 kW weight of the machine ca.: 0,8 t dimensions of the machine ca.: 1,2 x 0,8 x 2,1 m Bandsaw with - Saw blade welding unit - Grinding stone - Saw bands - documentation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
pressure: 40 t throat: 225 mm stroke: mm total power requirement: 4,7 kW weight of the machine ca.: 3,45 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
bore capacity in steel (diameter): 75 mm total power requirement: 14 kW weight of the machine ca.: 10 t - capacity at boring: 75 mm ( St 45 ) - spindle diam. 115 mm - taper in spindle: 110 mm/ Morse 6 - distance column to drilling spindel: 500.. . 2000 mm - vertical adjustment of arm: max. 1100 mm - distance column to drilling spindel: 450.. 2000 mm - drilling depth: 450 mm - range of speeds: 12,5 ...1600 U/ min // rpm - feed: 0,63 ... 3,15 mm / U - angle of arm: 360 ° The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Vertical turning lathe SEDIN 1512 CNC CNC control- Eastern origin Table diameter: 1120 mm Max work-piece: -Diameter: 1250 mm -Height: 1000 mm -Weight: 3200 kg Table speeds range per 1 min: 5-250 Tool dimensions: 25×40 Max horizontal travel of the vertical ram: 775 mm Max vertical travel of the vertical ram: 700 mm Max horizontal travel of the horizontal ram: 630 mm Max vertical travel of the horizontal ram: 1000 mm Max turning angle of the vertical ram: 45 degree Cross rail: -Travel: 660 mm -Speed: 400 mm/min Main motor power: 30 kW Overall dimensions: 2750×2975×4100 mm Machine weight: 15700 kg
SEDIN 1516 Vertical Turret Lathe Turning diameter: 1600 mm Table diameter: 1400 mm Max workpiece height: 1000 mm Max table loading: 5000 kg Max horizontal ram travel: 630 mm Max horizontal carriage travel: 975 mm Max vertical ram travel: 700 mm Max vertical carriage travel: 1000 mm No of feed carriages: 16 Carriages feed range: 0,07-12,5 mm/rev Distance between table and ram: 0-1225mm Fast stroke: 2000 mm/min Main motor power: 30 kW Speeds range: 4 - 200 rpm Dimensions: 3190x3360x4100 mm Weight: 19200 kg Side support
SEDIN 1516 CNC Vertical Turret Lathe CNC control- Eastern origin Turning diameter: 1600 mm Table diameter: 1400 mm Max workpiece height: 1000 mm Max table loading: 5000 kg Max horizontal ram travel: 630 mm Max horizontal carriage travel: 975 mm Max vertical ram travel: 700 mm Max vertical carriage travel: 1000 mm No of feed carriages: 16 Carriages feed range: 0,07-12,5 mm/rev Distance between table and ram: 0-1225mm Fast stroke: 2000 mm/min Main motor power: 30 kW Speeds range: 4 - 200 rpm Dimensions: 3190x3360x4100 mm Weight: 18200 kg
Slot head for milling machine, milling head, CCCP / USSR STANKO Type 1502Nr: 200 Year of construction 1974Stroke size: max. 60 mmStroke rate: approx. 200 - 500 strokes/min. Tool holder: 12 x 17 mm with clamping plateHole spacing machine-flange plate: 245 x 185 mmMounting hole: 17 mmCentering diameter on the machine flange plate: 190 mm- Stroke size adjustable via eccentric adjustment- The drive is as with the normal vertical head from the machine gearbox- Drive via driver, centric in the centering diameter- Degree scaling at the
pressure: 100 t throat: 355 mm stroke: mm total power requirement: 11,5 kW weight of the machine ca.: 8,5 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.
Capacity (ton) 315 Table size, mm 2500 x 1250 Slider stroke, mm 400 Shut height,mm 750 Strokes per min 25 Press weight, kg 50900
STANKO 5K822B Thread Grinding machine Grinding diameter 200 mm Grinding length 500 mm Max. grinding wheel diameter 400 mm Max. workpiece weight 30 kg Machine weight: approx. 4500 kg -for grinding of cylindrical and tapered, left and right, single-start and multi-start internal and outernal threads of various profiles.
- Table rotation 360 Gr - Head tilting possible up to 10 Gr - Big Cabinet with slotting key way tools - Lubrication - Complete Overhauled in 1994
gebr. Milling machine, Fabr. Stanko Type 6175 Travel X/Y/Z: 320/210/300 mm Spindle speed: 50 - 2040 rpm Feed speed: 13 - 395 mm/min Drive power: 1.5 kW Tool holder: 4 MK Groove width: 14 mm Number of grooves: 3 pieces Groove spacing: 50 mm
Drilling capacity (steel): 50mm, spindle speed: 1700rpm, reach: 45mm-1500mm, workpiece height range: 470mm-1500mm, sleeve stroke: 680mm, quill stroke: 350mm, spindle taper: MK5, max. tool weight: approx. 30kg. Machine dimensions X/Y/Z: approx. 2600mm/1100mm/3500mm, weight: approx. 4000kg. An on-site inspection is possible.
maximum number of results exceeded
please refine your search
