st used for sale

Description of the chip press: Powerful metal chip press with chip shredder for long turnings. The area of application is the processing of large quantities of milled and turning chips. Materials: aluminum, steel, cast iron Drip pan as oil tank Geared motor for optimal agitator operation Hydraulic Compression Cylinder Hydraulic press cylinder with two coaxial sections Diameter of briquettes 60 mm Automatic briquette length adjustment with displacement transducers Inductive Proximity Sensors Pre-compaction cylinder in conjunction with special compression hydraulic cylinder that compacts the material in the bushing-bulkhead unit Briquette ejection system, consisting of a compression chamber and a bulkhead with special anti-wear treatment Highly efficient closed-circuit oil cooling system consisting of an air/oil heat exchanger Hydraulic system with B ...

Capacity: 1000 KG, 2x12V battery

Hydraulic mobile tin hole punch for e.g. control cabinet construction and control construction Manufacturer Alfra Type SKP-1 Punches holes of max 140mm diameter in 3mm sheet metal Round, square and rectangular stamps possible. Punch punch punch tin punch drill tin hole drill monocut gap-plate-hole, hand hydraulics, ball bearing screw, Klauke Alfra Special price

Bread rolls Stüpfler stainless steel 380 volts -30 in part

IMA FILLING AND CLOSING MACHINE, MODEL STERIFILL SMART PWD Year of construction: 2017 IMA SMART PWD is able not only to process difficult powders accurately, but also to simultaneously dose, by vacuum-pressure, two different types of pharmaceutical products inside the same vial, with single 100% check-weighing. Speed: max. 100 pcs/min Available formats: 10R Transport system: Intermittent motion Highlights Possibility of dosing up to 2 different pharmaceutical powders in the same vial Vacuum-pressure powder filling system Advanced 100% IPC with speeds of up to 120 pcs/min Possible integration of a capping station Pick & place stoppering system Fit for isolation technology with possibility of wetting in place cRABS for powder containment Technical characteristics Standard voltage: 400 V, 50 Hz, 3ph + N + G Installed power: 19 kW

article nr. : 67347-0101 Control card brake of PT 8 Tetra Pak Pull Tab applicator

MAZAK CO2 Laser Cutting Machine STX510 MKIII 4kW -made in Japan- ! SOFORT EINSATZBEREIT ! over-recovered, very well-preserved MAZAK laser machine with 4000W Panel size: 3000mm x 1500mm minimum set-up area of 2.9m x 7.3m Puncture sensor Plasma sensor Burning Sensor automatic nozzle change Small parts conveyor belt Ball roller table Fast-punching fully encapsulated machine cover Cast bed, no foundation needed FE: up to 20mm VA: up to 15mm ALMG: up to 10mm Plastic, wood cutable incl. CAD / CAM Software 2020 Version incl. 12 months warranty (within Dtl.) incl. delivery incl. commissioning + training Testing under electricity ready for delivery immediately immediately ready for use =optional with fully automatic loading and unloading MAZAK CELL=

Scissor knife for table scissors . Shear knife. Knives.

Pizza oven with two floors, hood, and fermentation chamber GMG The baking chamber is completely made of refractory stone Temperature range: 50 to 400°C The front side made from stainless steel Digital control Upper and lower heat are separately adjustable Digital monitoring for upper and lower heat settings Digital error code system Heavy-duty temperature-resistant door with tension spring Double-glazing door glass for strengthened insulation and air circulation External dimensions: 149x110x194cm Internal dimensions: 105x70x15cm Electric power: 2 x 8 kW - 3NAC I 400 V Fermentation chamber: 149 x 93 x 90 cm - 3kW and 230 V Weight: 500 kg

Used Stork monoblock. 32 fillers and 8 screw heads. For PET bottles. Dose adjustment on the pistons.

Used Stork Wolf model MRS-2500.

Spreading attachment PIETSCH STA 1.7 MW series 2000, capacity 1.7 m3, conveyor belt, tarpaulin folding roof, spreader rubber, drive via vehicle hydraulics, with remote control and support supports. Sale as is or in parts possible.

all stainless steel electrically heated 4 x 9 kW frying length 1,500 mm belt width 400 mm adjustable speed oil level control manual hoists suitable for fire protection overall dimensions (l x w x h) : x 4,350 x 1,750 x 2,250 mm

FISH FOOD / PET FOOD EXTRUSION LINE CAN HAVE MANY APLLICATIONS FROM PET FOOD TO FISH FOOD was used to produce dog food output till 2 / 3 tonnes according to formulas Extruder was well maintained MODEL BC 82, TWIN SCEWS, has rails allowing to open totally the extruder to clean screw and barrels Extruder main electric cabinet coming with the line Conditionner Wenger , stainless, model 7 DCC , new in 2000 used for 2 years extruder main electric engine new in 2000, Continuous current LAK 4180 DA 400 volts, used for 2 years pelleting device, sieve, scale, buffer bin, STOLZ coater, STG 500 with vacum pomp the cooler (STOLZ RCC SEP 22X22F ) is not any included in the line many accessories, pomps, valves are coming with the line The line is partialy diassembled, plans could be provided Visits can be planned, enquiries for further details are welcome

VIRO StyroDesign XL-2 EPS cutting machine was built in 2011 in Slovenia by VIRO pakirni stroji d. o. o. The machine is used for precision cutting of materials such as EPS blocks, using hot resistance wires. The process is extremely fast and efficient thanks to the use of a large number of 2000 mm long wires. The machining parameters are programmed in the state-of-the-art SytroDesignPRO software, which, thanks to the optimisation of the cutting layouts, significantly facilitates process management and reduces material losses. All this makes the StyroDesign XL-2 styrofoam cutting machine an excellent choice for the production of, among others, insulation components and other prefabricated building components. Technical specifications of VIRO StyroDesign XL-2 foam cutting machine - software: StyroDesign PRO - cutting angle: 90° - cutting speed: up to 2.5 m/min - ability to cut at an ...

N GREAT WORKING CONDITION ONLY 90 WORKING HOURS

LVD Siena strippit 1212 punching machine was built in 2005 in Belgium by LVD Group NV. Designed for machining steel and aluminium sheets, the machine is an excellent choice for both unit and batch production. Reliable components with excellent performance, combined with a compact design based on a one-piece frame, ensure that the SIENA 20 1212 punching machine delivers excellent precision and machining quality for many years of use. The capacious, 27-station turret with 3 auto-index stations and MultiTool support offers a wide variety of machining options and a high level of flexibility. Precision tools punch metal sheets with a force of 20 tonnes on a large brush table, which protects the surface of the workpiece from scratches and scrapes, while increasing the quality of machining. All of this is completed by the GE FANUC CNC control with its unique Smart Stroke function for automat ...

STILL EXV-SF 14 electric pallet stacker was built in 2023 by German company STILL GmbH. This extremely versatile vehicle allows you to control the flow of goods in your warehouse, from transporting loads in the goods receiving area to handling high-bay racks. The maximum load capacity of 1400 kg, combined with the intelligent speed reduction in corners, ensure maximum safety in transporting loads in even the most confined spaces. When the stand-on platform and side lateral protection arms are extended, the maximum speed without load can reach up to 10 km/h. The machine’s structure has been designed for maximum operator comfort. The pneumatically cushioned stand-on platform, which can be adjusted to the operator’s weight, protects the back from strain over long distances. Precise controls have been adapted to both right- and left-handed operators. On top of this, the operator has a ...

Double-tubing stainless steel tanks very stable quality. Suitable for cooling with a net content of 2500 l

Eccentric screw pump with funnel Power: approx. 15-20m3 per hour Infinitely adjustable with adjustable motor Dimensions and weight: Length: 3100 mm Width: 820 mm Height: 1300 mm Engine data s. Photos

Good day We hereby offer you a used baler from the manufacturer Strautmann, type BaleTainer. The following technical data have been taken from the manufacturer's operating instructions and brochures, for which we cannot assume any liability for accuracy and completeness. Manufacturer Strautmann Type BaleTainer Year of construction 2013 Operating hours 18,819 hours Number of bales pressed: 7,019 pieces Press force main press 60 t Drive power 9.2 kW Machine weight press 7.38 t The press has been partially overhauled. Piston rods and gasket sets of the two main hydraulic cylinders were renewed and general maintenance work such as oil and filter changes etc. was carried out. Finally, after the overhaul work, the machine was tested. For feeding, the press has a hydraulic tilting device to empty lattice box containers at a truck ramp. For example, the machine can be par ...

Due to new motorization In the current state Expanded turning hours plus minus 42,000

Plate plate made of cast iron with longitudinal grooves and mounting holes, manufactured according to DIN876, the T - grooves manufactured according to DIN650 - H12. - 4 plates with dimensions 3,000 mm x 1,200 mm x H 300 mm.

Clamping plate 5,000 mm x 2,000 mm x H 400 mm made of cast iron with 10 pieces T - grooves with 35 mm width, manufactured according to DIN876, the T - grooves manufactured according to DIN650 - H12.

Clamping plate 5,000 mm x 1,980 mm x H 300 mm made of cast iron, with 6 pieces T - grooves with 35 mm width, manufactured according to DIN876, the T - grooves manufactured according to DIN650 - H12.

20121 - MARINE GEARBOX TK 600S - 571 HP AT 2100 RPM - RATIOS 1.97,2.53, 2.75,3.04, 3.42 Brand Gearbox TK Model Gearbox 600S-1 Ratio 1.97,2.53, 2.75,3.04, 3.42 Power 571 HP RPM 2100 RPM General condition BRAND NEW Status AVAILABLE SPECIFIC INFORMATION Sae housing SAE 1 Flexible coupling YES AND ALU. FLANGE Controls NO SPECIFIC FEATURES Brackets YES Oil cooler YES DIMENSIONS Weight (kg) 600 KG

Brand Gearbox TK Model Gearbox 600S-1 Ratio 1.97,2.53, 2.75,3.04, 3.42 Power 571 HP RPM 2100 RPM General condition BRAND NEW Status AVAILABLE SPECIFIC INFORMATION Sae housing SAE 1 Flexible coupling YES AND ALU. FLANGE Controls NO SPECIFIC FEATURES Brackets YES Oil cooler YES DIMENSIONS Weight (kg) 600 KG

Big Bag filling station, filling and weighing system used The system consists of the following components: 1 filling hopper approx. 2300 height 2500 mm 2 stainless steel trough screws 1 tumbling/shaking sieve approx. 1200 height 1900 mm 1 BigBag filling station approx. 1950 x 2400 x 3700 mm 1 control cabinet The Big Pack filling is filled by wheel loader or forklift via a pouring funnel. The filling material is transported via a conveyor screw to a tumbling sieve. From there, transported with another screw to the actual weighing and filling station. The big bags lie on a vibrating floor when filling and are thus compacted.

The scope of delivery includes: Steel panel, new Material colour: sendzimir galvanised Total width: approx. 295 mm Total depth: approx. 1,110 mm Inner depth: approx. 1,104 mm for column depth: approx. 1,100 mm Clear span: approx. 992 mm Truss support: approx. 55 mm Height of bending: approx. 25 mm Material thickness: approx. 2.00 mm Weight / piece: approx. 5.95 kg Other quantities on request. Quantity: - clear width trusses: 01 pcs. 02 pcs. 06 pcs - 1,800 mm 07 pcs - 2,100 mm 08 pcs - 2,400 mm 09 pcs - 2,700 mm 10 pcs. - 3,000 mm 11 pcs. - 3,300 mm 12 pcs - 3,600 mm 13 pcs - 3,900 mm 20 pcs. 50 pcs. 75 pcs. 100 pcs. Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. An additional desired transport or a shipment of this item is a ...

Mobile marking station Marking of metal parts - was used in Faurecia Machine checked - fine, ready for use

Qty. 1 Second-hand carusel Monoblok filling line Mfc.: Stork Bepak B.V. Built: 1992 Type: VS 60/110/12LV Capacity: 20 000 Btl./h No. of filling stations: 60 pieces No. of closing heads: 12 pieces Size of buttles: 250, 500, 700 & 750 ml Inspector checking the fill level and cap Very good condition!

STEPPER RS - 12470917

Тype: WALDYSSA 33 Stretchfilm wrapping machine Маx. trays dimensions L x B x H: 300 x 200 x 160 mm Мin. trays dimensions L x B x H: 110 x 90 x 10 mm Capacity: max. 28 trays / min Machine dimensions: Length: 2500 mm Width: 1450 mm Height: 1500 mm Voltage: 380 V, 50Hz Power: 2,6 kW Machine weight: 350 kg

The scope of delivery includes: 01x Stand protection, used Manufacturer: Meta (Thyssen) Material colour: orange Total height: approx. 1,255 mm Total width: approx. 105 mm Inner width: approx. 86 mm Suitable for frame profile: 85 mm Material thickness: approx. 4.0 mm Total depth: approx. 60 mm Height deflector: approx. 50 mm Leg size: approx. 75 x 75 mm Original clasp tabs Weight | Pcs.: 12,51 kg. Your contact persons in our company: Mr.: Andre Evering Sir: Mario Klöver Mr.: Falk German General information about the article: This item is only available for pickup. Any additional transport or shipment of this item is associated with additional costs, which can be requested separately depending on the delivery location or scope of delivery.

Push-mast forklift, high-bay forklift used Manufacturer: STEINBOCK BOSS Type: WA15R-19130 MK II A-1 Built: 1999 Operating hours read: 10747 Callable capacity max 1000 kg Lifting height: 8750 mm Weight without battery: 6550 kg Battarie 80V 4 PzS 620 kW13/2019 Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.

Shrink Tunnel Kallfass Standard 450 N; State as is; checked only for function; Inlet width 400mm; Pass-through height 200mm; Cooling fan. Shrink tunnel Kallfass Standard 450 N; condition as is; only chekced on function; width 400mm; hight 200mm; cooling unit.

Sell a well-preserved triple honing machine from Stanko. The machine was in use until it was dismantled. The dimensions of the machine are LXWXH 800mm x 1100mm x 1650mm. The weight is 800kg. The dimensions of the control cabinet are LxWxH 350mm x 950mm x 1550mm. The weight is approx. 150kg. If you have any questions, just get in touch. The machine can be viewed by prior appointment. Shipping, on 2 pallets, is no problem. Please inquire about shipping costs with zip code. Furthermore, the machine can be delivered and unloaded in the immediate vicinity with its own crane truck and against assumption of costs. On-site loading is no problem and free of charge. The sale is without warranty and guarantee. The return is excluded. All information without guarantee.

Steel construction, machine platform, used steel scaffolding Manufacturer: EHINGER IMPIANTI Dimensions approx. 4.8 x 4.6 x 8.7 m The system has already been dismantled. Any machines and devices that can be seen in the pictures are not part of the scope of delivery. We only offer the steel construction here. The construction was part of a glass recycling plant in which foam glass bulkowas was manufactured. We sell the complete plant with belt furnaces, cup plants, silos, crushers and mills. Subject to changes and errors in the technical data, dates and prices as well as intermediate sale.

Semi-automatic machine Workpiece diameter 40-400 mm Max. workpiece length 2000 mm Spindle rotation frequency 16-1460 rpm Workpiece spindle speed 3-180 rpm Max. diameter of grinding: -In steady rest 120 mm -Without steady rest 360 mm Max. grinding length 1800 mm Height of centers above the table- 210 mm Max. work-piece weight- 1000 kg Grinding wheel dia min/max 500-750 mm Max. length of table travel- 1800 mm Spindle taper- Morze 6 Motor power: 13 kW Periodical feed of grinding headstock: -Max.: 0,030±0,0025 mm -Min.: 0,0025±0,0006 mm Max. axial travel of grinding headstock spindle: ±2,5 mm

Free-swinging model S33 according to Mart Stam in white leather

Conveyor belt / belt conveyor Belt width: approx. 1,400 mm Axle distance: approx. 8,000 mm Drive: 2.2 kW

Manufacturer: Homag aus Homag KF 20, Type: Ein und Ausgangskarten Streckensteuerung,

Manufacturer: Stöber, Model: FDS 2024/B, Serial number: 463602591, FREE TEXT: weitere Angaben entnehmen Sie den Bildern,

Manufacturer: Stöber Umrichter, Type: 1040 B, Serial number: 1172564/894,

Manufacturer: Heesemann Bedienteil LSM 8, Type: Steuerung Schleifmaschine,

Manufacturer: Sutron BT 20 Steurungspanel, Type: BT 20,